hwmon: add OneXPlayer mini AMD sensors driver
Subsystems (3)
PATCH v5 1/1 hwmon: add OneXPlayer mini AMD sensors driver
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading and control via hwmon sysfs.
As far as I could gather all OXP boards have the same DMI strings and they are told appart by the boot cpu vendor (Intel/AMD). Currently only AMD boards are supported.
Fan control is provided via pwm interface in the range [0-255]. AMD boards have [0-100] as range in the EC, the written value is scaled to accommodate for that.
Signed-off-by Joaquín Ignacio Aramendía <[email protected]>
---
Improved documentation with sysfs attributes. Fixed missing breaks.
Shortened return code in init.
Removed debug message in read/write functions. Cleaned a read value modification on error condition.
--- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/oxp-sensors.rst | 34 ++++ MAINTAINERS | 6 + drivers/hwmon/Kconfig | 11 ++ drivers/hwmon/Makefile | 1 + drivers/hwmon/oxp-sensors.c | 255 ++++++++++++++++++++++++++++ 6 files changed, 308 insertions(+) create mode 100644 Documentation/hwmon/oxp-sensors.rst create mode 100644 drivers/hwmon/oxp-sensors.c
Documentation/hwmon/index.rst +1 -0
@@ -160,6 +160,7 @@ Hardware Monitoring Kernel Drivers nzxt-kraken2 nzxt-smart2 occ + oxp-sensors pc87360 pc87427 pcf8591
Documentation/hwmon/oxp-sensors.rst new file +34 -0
@@ -0,0 +1,34 @@ +.. SPDX-License-Identifier: GPL-2.0-or-later + +Kernel driver oxp-sensors +========================= + +Author: + - Joaquín Ignacio Aramendía <[email protected]> + +Description: +------------ + +One X Player devices from One Netbook provide fan readings and fan control +through its Embedded Controller. + +Currently only supports AMD boards from the One X Player lineup. Intel boards +could be supported if we could figure out the EC registers and values to write +to since the EC layout and model is different. + +Sysfs entries +------------- + +The following attributes are supported: + +fan1_input + Read Only. Reads current fan RMP. + +pwm1_enable + Read Write. Enable manual fan control. Write "1" to set to manual, write "0" + to let the EC control de fan speed. Read this attribute to see current status. + +pwm1 + Read Write. Read this attribute to see current duty cycle in the range [0-255]. + When pwm1_enable is set to "1" (manual) write any value in the range [0-255] + to set fan speed.
MAINTAINERS +6 -0
@@ -15337,6 +15337,12 @@ S: Maintained F: drivers/mtd/nand/onenand/ F: include/linux/mtd/onenand*.h +ONEXPLAYER FAN DRIVER +M: Joaquín Ignacio Aramendía <[email protected]> +L: [email protected] +S: Maintained +F: drivers/hwmon/oxp-sensors.c + ONION OMEGA2+ BOARD M: Harvey Hunt <[email protected]> L: [email protected]
drivers/hwmon/Kconfig +11 -0
@@ -1607,6 +1607,17 @@ config SENSORS_NZXT_SMART2 source "drivers/hwmon/occ/Kconfig" +config SENSORS_OXP + tristate "OneXPlayer EC fan control" + depends on ACPI + depends on X86 + help + If you say yes here you get support for fan readings and control over + OneXPlayer handheld devices. Only OneXPlayer mini AMD handheld variant + boards are supported. + + Can also be built as a module. In that case it will be called oxp-sensors. + config SENSORS_PCF8591 tristate "Philips PCF8591 ADC/DAC" depends on I2C
drivers/hwmon/Makefile +1 -0
@@ -167,6 +167,7 @@ obj-$(CONFIG_SENSORS_NSA320) += nsa320-hwmon.o obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o obj-$(CONFIG_SENSORS_NZXT_KRAKEN2) += nzxt-kraken2.o obj-$(CONFIG_SENSORS_NZXT_SMART2) += nzxt-smart2.o +obj-$(CONFIG_SENSORS_OXP) += oxp-sensors.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o obj-$(CONFIG_SENSORS_PC87427) += pc87427.o obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o
drivers/hwmon/oxp-sensors.c new file +255 -0
255 lines not on this page · raw message
--
2.38.1