ARM: dts: at91: sama7g5ek: align power rails for sdmmc0/1
Subsystems (2)
PATCH 1/1 ARM: dts: at91: sama7g5ek: align power rails for sdmmc0/1
On this board SDMMC0 has a 1.8 signaled eMMC device powered at 3.3 V .
Hence, correctly describe the connected rails from the PMIC.
SDMMC1 is connected to a voltage switch that can change from 3.3V to 1.8V by a hardware controlled pin.
However SDMMC1 at the moment works only 3.3V mode (default speed, no UHS-I modes), thus connect the signaling to the 3.3V rail.
--- arch/arm/boot/dts/at91-sama7g5ek.dts | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm/boot/dts/at91-sama7g5ek.dts +4 -1
@@ -764,8 +764,9 @@ &rtt { &sdmmc0 { bus-width = <8>; non-removable; - no-1-8-v; sdhci-caps-mask = <0x0 0x00200000>; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vldo1>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sdmmc0_default>; status = "okay";
@@ -775,6 +776,8 @@ &sdmmc1 { bus-width = <4>; no-1-8-v; sdhci-caps-mask = <0x0 0x00200000>; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vdd_3v3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sdmmc1_default>; status = "okay";
Signature · 1 line
2.25.1
[email protected]
AppliedQuoted 10 lines · Eugen Hristev
On this board SDMMC0 has a 1.8 signaled eMMC device powered at 3.3 V .
Hence, correctly describe the connected rails from the PMIC.SDMMC1 is connected to a voltage switch that can change from 3.3V to 1.8V by a hardware controlled pin.
However SDMMC1 at the moment works only 3.3V mode (default speed, no UHS-I modes), thus connect the signaling to the 3.3V rail.Signed-off-by Eugen Hristev <[email protected]>
Applied to at91-dt (after reshaped a bit the commit message), thanks!
Quoted 28 lines
--- arch/arm/boot/dts/at91-sama7g5ek.dts | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)arch/arm/boot/dts/at91-sama7g5ek.dts +4
-1@@ -764,8 +764,9 @@ &rtt { &sdmmc0 { bus-width = <8>; non-removable; - no-1-8-v; sdhci-caps-mask = <0x0 0x00200000>; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vldo1>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sdmmc0_default>; status = "okay";@@ -775,6 +776,8 @@ &sdmmc1 { bus-width = <4>; no-1-8-v; sdhci-caps-mask = <0x0 0x00200000>; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vdd_3v3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sdmmc1_default>; status = "okay";