Skip to contentSkip to conversation

ASoC: fsl_micfil: explicitly clear software reset bit

PATCH New Sasha Levin 1 participant 10 messages Dec 6, 2022

Subsystems (8)
lore
Share & tools
lore
author maintainer
#6 lore raw

PATCH 7/10 can: mcba_usb: Fix termination command argument

In reply to Sasha Levin

From: Yasushi SHOJI <[email protected]>

[ Upstream commit 1a8e3bd25f1e789c8154e11ea24dc3ec5a4c1da0 ]

Microchip USB Analyzer can activate the internal termination resistors by setting the "termination" option ON, or OFF to to deactivate them. As I've observed, both with my oscilloscope and captured USB packets below, you must send "0" to turn it ON, and "1" to turn it OFF.

From the schematics in the user's guide, I can confirm that you must drive the CAN_RES signal LOW "0" to activate the resistors.

Reverse the argument value of usb_msg.termination to fix this.

These are the two commands sequence, ON then OFF.

Quoted 7 lines
No.     Time           Source                Destination           Protocol Length Info
      1 0.000000       host                  1.3.1                 USB      46     URB_BULK out

Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits) USB URB
Leftover Capture Data: a80000000000000000000000000000000000a8

Quoted 6 lines
No.     Time           Source                Destination           Protocol Length Info
      2 4.372547       host                  1.3.1                 USB      46     URB_BULK out

Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits) USB URB
Leftover Capture Data: a80100000000000000000000000000000000a9

---
 drivers/net/can/usb/mcba_usb.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/net/can/usb/mcba_usb.c +7 -3
index 21063335ab59..c07e327929ba 100644
@@ -47,6 +47,10 @@
 #define MCBA_VER_REQ_USB 1
 #define MCBA_VER_REQ_CAN 2
 
+/* Drive the CAN_RES signal LOW "0" to activate R24 and R25 */
+#define MCBA_VER_TERMINATION_ON 0
+#define MCBA_VER_TERMINATION_OFF 1
+
 #define MCBA_SIDL_EXID_MASK 0x8
 #define MCBA_DLC_MASK 0xf
 #define MCBA_DLC_RTR_MASK 0x40
@@ -469,7 +473,7 @@ static void mcba_usb_process_ka_usb(struct mcba_priv *priv,
 		priv->usb_ka_first_pass = false;
 	}
 
-	if (msg->termination_state)
+	if (msg->termination_state == MCBA_VER_TERMINATION_ON)
 		priv->can.termination = MCBA_TERMINATION_ENABLED;
 	else
 		priv->can.termination = MCBA_TERMINATION_DISABLED;
@@ -789,9 +793,9 @@ static int mcba_set_termination(struct net_device *netdev, u16 term)
 	};
 
 	if (term == MCBA_TERMINATION_ENABLED)
-		usb_msg.termination = 1;
+		usb_msg.termination = MCBA_VER_TERMINATION_ON;
 	else
-		usb_msg.termination = 0;
+		usb_msg.termination = MCBA_VER_TERMINATION_OFF;
 
 	mcba_usb_xmit_cmd(priv, (struct mcba_usb_msg *)&usb_msg);
 
Signature · 1 line
2.35.1
author maintainer
#2 lore raw

PATCH 3/10 ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()

In reply to Sasha Levin

From: Mark Brown <[email protected]>

[ Upstream commit 97eea946b93961fffd29448dcda7398d0d51c4b2 ]

The bounds checks in snd_soc_put_volsw_sx() are only being applied to the first channel, meaning it is possible to write out of bounds values to the second channel in stereo controls. Add appropriate checks.

---
 sound/soc/soc-ops.c | 6 ++++++
 1 file changed, 6 insertions(+)
sound/soc/soc-ops.c +6 -0
index 0f26d6c31ce5..49d22233d391 100644
@@ -447,6 +447,12 @@ int snd_soc_put_volsw_sx(struct snd_kcontrol *kcontrol,
 	if (snd_soc_volsw_is_stereo(mc)) {
 		val_mask = mask << rshift;
 		val2 = (ucontrol->value.integer.value[1] + min) & mask;
+
+		if (mc->platform_max && val2 > mc->platform_max)
+			return -EINVAL;
+		if (val2 > max)
+			return -EINVAL;
+
 		val2 = val2 << rshift;
 
 		err = snd_soc_component_update_bits(component, reg2, val_mask,
Signature · 1 line
2.35.1
author maintainer
#7 lore raw

PATCH 8/10 net: loopback: use NET_NAME_PREDICTABLE for name_assign_type

In reply to Sasha Levin

From: Rasmus Villemoes <[email protected]>

[ Upstream commit 31d929de5a112ee1b977a89c57de74710894bbbf ]

When the name_assign_type attribute was introduced (commit 685343fc3ba6, "net: add name_assign_type netdev attribute"), the loopback device was explicitly mentioned as one which would make use of NET_NAME_PREDICTABLE:

The name_assign_type attribute gives hints where the interface name of a given net-device comes from. These values are currently defined:
...
NET_NAME_PREDICTABLE:
The ifname has been assigned by the kernel in a predictable way that is guaranteed to avoid reuse and always be the same for a given device. Examples include statically created devices like the loopback device [...]

Switch to that so that reading /sys/class/net/lo/name_assign_type produces something sensible instead of returning -EINVAL.

---
 drivers/net/loopback.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/loopback.c +1 -1
index a1c77cc00416..498e5c8013ef 100644
@@ -208,7 +208,7 @@ static __net_init int loopback_net_init(struct net *net)
 	int err;
 
 	err = -ENOMEM;
-	dev = alloc_netdev(0, "lo", NET_NAME_UNKNOWN, loopback_setup);
+	dev = alloc_netdev(0, "lo", NET_NAME_PREDICTABLE, loopback_setup);
 	if (!dev)
 		goto out;
 
Signature · 1 line
2.35.1
author maintainer
#4 lore raw

PATCH 5/10 pinctrl: meditatek: Startup with the IRQs disabled

In reply to Sasha Levin

From: Ricardo Ribalda <[email protected]>

[ Upstream commit 11780e37565db4dd064d3243ca68f755c13f65b4 ]

If the system is restarted via kexec(), the peripherals do not start with a known state.

If the previous system had enabled an IRQs we will receive unexected IRQs that can lock the system.

[   28.109251] watchdog: BUG: soft lockup - CPU#0 stuck for 26s!
[swapper/0:0]
[   28.109263] Modules linked in:
[   28.109273] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
5.15.79-14458-g4b9edf7b1ac6 #1 9f2e76613148af94acccd64c609a552fb4b4354b
[   28.109284] Hardware name: Google Elm (DT)
[   28.109290] pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS
		BTYPE=--)
[   28.109298] pc : __do_softirq+0xa0/0x388
[   28.109309] lr : __do_softirq+0x70/0x388
[   28.109316] sp : ffffffc008003ee0
[   28.109321] x29: ffffffc008003f00 x28: 000000000000000a x27:
0000000000000080
[   28.109334] x26: 0000000000000001 x25: ffffffefa7b350c0 x24:
ffffffefa7b47480
[   28.109346] x23: ffffffefa7b3d000 x22: 0000000000000000 x21:
ffffffefa7b0fa40
[   28.109358] x20: ffffffefa7b005b0 x19: ffffffefa7b47480 x18:
0000000000065b6b
[   28.109370] x17: ffffffefa749c8b0 x16: 000000000000018c x15:
00000000000001b8
[   28.109382] x14: 00000000000d3b6b x13: 0000000000000006 x12:
0000000000057e91
[   28.109394] x11: 0000000000000000 x10: 0000000000000000 x9 :
ffffffefa7b47480
[   28.109406] x8 : 00000000000000e0 x7 : 000000000f424000 x6 :
0000000000000000
[   28.109418] x5 : ffffffefa7dfaca0 x4 : ffffffefa7dfadf0 x3 :
000000000000000f
[   28.109429] x2 : 0000000000000000 x1 : 0000000000000100 x0 :
0000000001ac65c5
[   28.109441] Call trace:
[   28.109447]  __do_softirq+0xa0/0x388
[   28.109454]  irq_exit+0xc0/0xe0
[   28.109464]  handle_domain_irq+0x68/0x90
[   28.109473]  gic_handle_irq+0xac/0xf0
[   28.109480]  call_on_irq_stack+0x28/0x50
[   28.109488]  do_interrupt_handler+0x44/0x58
[   28.109496]  el1_interrupt+0x30/0x58
[   28.109506]  el1h_64_irq_handler+0x18/0x24
[   28.109512]  el1h_64_irq+0x7c/0x80
[   28.109519]  arch_local_irq_enable+0xc/0x18
[   28.109529]  default_idle_call+0x40/0x140
[   28.109539]  do_idle+0x108/0x290
[   28.109547]  cpu_startup_entry+0x2c/0x30
[   28.109554]  rest_init+0xe8/0xf8
[   28.109562]  arch_call_rest_init+0x18/0x24
[   28.109571]  start_kernel+0x338/0x42c
[   28.109578]  __primary_switched+0xbc/0xc4
[   28.109588] Kernel panic - not syncing: softlockup: hung tasks
---
 drivers/pinctrl/mediatek/mtk-eint.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/pinctrl/mediatek/mtk-eint.c +6 -3
index 22736f60c16c..64a32d3ca481 100644
@@ -278,12 +278,15 @@ static struct irq_chip mtk_eint_irq_chip = {
 
 static unsigned int mtk_eint_hw_init(struct mtk_eint *eint)
 {
-	void __iomem *reg = eint->base + eint->regs->dom_en;
+	void __iomem *dom_en = eint->base + eint->regs->dom_en;
+	void __iomem *mask_set = eint->base + eint->regs->mask_set;
 	unsigned int i;
 
 	for (i = 0; i < eint->hw->ap_num; i += 32) {
-		writel(0xffffffff, reg);
-		reg += 4;
+		writel(0xffffffff, dom_en);
+		writel(0xffffffff, mask_set);
+		dom_en += 4;
+		mask_set += 4;
 	}
 
 	return 0;
Signature · 1 line
2.35.1
author maintainer
#3 lore raw

PATCH 4/10 libbpf: Use page size as max_entries when probing ring buffer map

In reply to Sasha Levin

From: Hou Tao <[email protected]>

[ Upstream commit 689eb2f1ba46b4b02195ac2a71c55b96d619ebf8 ]

Using page size as max_entries when probing ring buffer map, else the probe may fail on host with 64KB page size (e.g., an ARM64 host).

After the fix, the output of "bpftool feature" on above host will be correct.

Before :
eBPF map_type ringbuf is NOT available
eBPF map_type user_ringbuf is NOT available

After :
eBPF map_type ringbuf is available
eBPF map_type user_ringbuf is available

---
 tools/lib/bpf/libbpf_probes.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/lib/bpf/libbpf_probes.c +1 -1
index d38284a3aaf0..13393f0eab25 100644
@@ -244,7 +244,7 @@ bool bpf_probe_map_type(enum bpf_map_type map_type, __u32 ifindex)
 	case BPF_MAP_TYPE_RINGBUF:
 		key_size = 0;
 		value_size = 0;
-		max_entries = 4096;
+		max_entries = sysconf(_SC_PAGE_SIZE);
 		break;
 	case BPF_MAP_TYPE_UNSPEC:
 	case BPF_MAP_TYPE_HASH:
Signature · 1 line
2.35.1
author maintainer
#9 lore raw

PATCH 10/10 nvme-pci: clear the prp2 field when not used

In reply to Sasha Levin

From: Lei Rao <[email protected]>

[ Upstream commit a56ea6147facce4ac1fc38675455f9733d96232b ]

If the prp2 field is not filled in nvme_setup_prp_simple(), the prp2 field is garbage data. According to nvme spec, the prp2 is reserved if the data transfer does not cross a memory page boundary, so clear it to zero if it is not used.

---
 drivers/nvme/host/pci.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/nvme/host/pci.c +2 -0
index 089f39103584..c222d7bf6ce1 100644
@@ -817,6 +817,8 @@ static blk_status_t nvme_setup_prp_simple(struct nvme_dev *dev,
 	cmnd->dptr.prp1 = cpu_to_le64(iod->first_dma);
 	if (bv->bv_len > first_prp_len)
 		cmnd->dptr.prp2 = cpu_to_le64(iod->first_dma + first_prp_len);
+	else
+		cmnd->dptr.prp2 = 0;
 	return BLK_STS_OK;
 }
 
Signature · 1 line
2.35.1
author maintainer
#1 lore raw

PATCH 2/10 ASoC: fsl_micfil: explicitly clear CHnF flags

In reply to Sasha Levin

From: Shengjiu Wang <[email protected]>

[ Upstream commit b776c4a4618ec1b5219d494c423dc142f23c4e8f ]

There may be failure when start 1 channel recording after 8 channels recording. The reason is that the CHnF flags are not cleared successfully by software reset.

This issue is triggerred by the change of clearing software reset bit.

CHnF flags are write 1 clear bits. Clear them by force write.

---
 sound/soc/fsl/fsl_micfil.c | 8 ++++++++
 1 file changed, 8 insertions(+)
sound/soc/fsl/fsl_micfil.c +8 -0
index ead4bfa13561..6c794605e33c 100644
@@ -201,6 +201,14 @@ static int fsl_micfil_reset(struct device *dev)
 	if (ret)
 		return ret;
 
+	/*
+	 * Set SRES should clear CHnF flags, But even add delay here
+	 * the CHnF may not be cleared sometimes, so clear CHnF explicitly.
+	 */
+	ret = regmap_write_bits(micfil->regmap, REG_MICFIL_STAT, 0xFF, 0xFF);
+	if (ret)
+		return ret;
+
 	return 0;
 }
 
Signature · 1 line
2.35.1

Sasha Levin

author maintainer
#0 lore raw

PATCH 1/10 ASoC: fsl_micfil: explicitly clear software reset bit

From: Shengjiu Wang <[email protected]>

[ Upstream commit 292709b9cf3ba470af94b62c9bb60284cc581b79 ]

SRES is self-cleared bit, but REG_MICFIL_CTRL1 is defined as non volatile register, it still remain in regmap cache after set, then every update of REG_MICFIL_CTRL1, software reset happens. to avoid this, clear it explicitly.

---
 sound/soc/fsl/fsl_micfil.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
sound/soc/fsl/fsl_micfil.c +11 -0
index efc5daf53bba..ead4bfa13561 100644
@@ -190,6 +190,17 @@ static int fsl_micfil_reset(struct device *dev)
 		return ret;
 	}
 
+	/*
+	 * SRES is self-cleared bit, but REG_MICFIL_CTRL1 is defined
+	 * as non-volatile register, so SRES still remain in regmap
+	 * cache after set, that every update of REG_MICFIL_CTRL1,
+	 * software reset happens. so clear it explicitly.
+	 */
+	ret = regmap_clear_bits(micfil->regmap, REG_MICFIL_CTRL1,
+				MICFIL_CTRL1_SRES);
+	if (ret)
+		return ret;
+
 	return 0;
 }
 
Signature · 1 line
2.35.1
author maintainer
#8 lore raw

PATCH 9/10 ASoC: cs42l51: Correct PGA Volume minimum value

From: Charles Keepax <[email protected]>

[ Upstream commit 3d1bb6cc1a654c8693a85b1d262e610196edec8b ]

The table in the datasheet actually shows the volume values in the wrong order, with the two -3dB values being reversed. This appears to have caused the lower of the two values to be used in the driver when the higher should have been, correct this mixup.

---
 sound/soc/codecs/cs42l51.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/codecs/cs42l51.c +1 -1
index fc6a2bc311b4..c61b17dc2af8 100644
@@ -146,7 +146,7 @@ static const struct snd_kcontrol_new cs42l51_snd_controls[] = {
 			0, 0xA0, 96, adc_att_tlv),
 	SOC_DOUBLE_R_SX_TLV("PGA Volume",
 			CS42L51_ALC_PGA_CTL, CS42L51_ALC_PGB_CTL,
-			0, 0x19, 30, pga_tlv),
+			0, 0x1A, 30, pga_tlv),
 	SOC_SINGLE("Playback Deemphasis Switch", CS42L51_DAC_CTL, 3, 1, 0),
 	SOC_SINGLE("Auto-Mute Switch", CS42L51_DAC_CTL, 2, 1, 0),
 	SOC_SINGLE("Soft Ramp Switch", CS42L51_DAC_CTL, 1, 1, 0),
Signature · 1 line
2.35.1
author maintainer
#5 lore raw

PATCH 6/10 can: sja1000: fix size of OCR_MODE_MASK define

In reply to Sasha Levin

From: Heiko Schocher <[email protected]>

[ Upstream commit 26e8f6a75248247982458e8237b98c9fb2ffcf9d ]

bitfield mode in ocr register has only 2 bits not 3, so correct the OCR_MODE_MASK define.

---
 include/linux/can/platform/sja1000.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
include/linux/can/platform/sja1000.h +1 -1
index 5755ae5a4712..6a869682c120 100644
@@ -14,7 +14,7 @@
 #define OCR_MODE_TEST     0x01
 #define OCR_MODE_NORMAL   0x02
 #define OCR_MODE_CLOCK    0x03
-#define OCR_MODE_MASK     0x07
+#define OCR_MODE_MASK     0x03
 #define OCR_TX0_INVERT    0x04
 #define OCR_TX0_PULLDOWN  0x08
 #define OCR_TX0_PULLUP    0x10
Signature · 1 line
2.35.1