Skip to contentSkip to conversation

engicam: imx6: migrate to DM_SERIAL

PATCH In review Suniel Mahesh 3 participants 4 messages Dec 9, 2022 – Jan 31, 2023

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 engicam: imx6: migrate to DM_SERIAL

From: Michael Trimarchi <[email protected]>

Add the needed DT overrides and configs to enable UART in SPL.

---
Note:
Tested this patch on Engicam Starter Kit with I.CORE - M6 (MCIMX6Q7CVT08AC) SOM.

---
 arch/arm/dts/imx6qdl-icore-u-boot.dtsi | 16 ++++++++++++++++
 arch/arm/dts/imx6ul-isiot-u-boot.dtsi  | 16 ++++++++++++++++
 board/engicam/common/spl.c             | 20 +++-----------------
 configs/imx6dl_icore_nand_defconfig    |  1 +
 configs/imx6q_icore_nand_defconfig     |  1 +
 configs/imx6qdl_icore_mipi_defconfig   |  1 +
 configs/imx6qdl_icore_mmc_defconfig    |  1 +
 configs/imx6qdl_icore_nand_defconfig   |  1 +
 configs/imx6qdl_icore_rqs_defconfig    |  1 +
 9 files changed, 41 insertions(+), 17 deletions(-)
arch/arm/dts/imx6qdl-icore-u-boot.dtsi +16 -0
index f95d49d00d..12e46e38f6 100644
@@ -5,6 +5,22 @@
 
 #include "imx6qdl-u-boot.dtsi"
 
+&soc {
+	u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+	u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
 &usdhc1 {
 	u-boot,dm-spl;
 };
arch/arm/dts/imx6ul-isiot-u-boot.dtsi +16 -0
index aa8e9804bf..7213e71989 100644
@@ -5,6 +5,22 @@
 
 #include "imx6ul-u-boot.dtsi"
 
+&soc {
+	u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+	u-boot,dm-pre-reloc;
+};
+
+&pinctrl_uart1 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart1 {
+	u-boot,dm-pre-reloc;
+};
+
 &usdhc1 {
 	u-boot,dm-spl;
 };
board/engicam/common/spl.c +3 -17
index 6a0612481a..f1ccdc3343 100644
@@ -26,20 +26,6 @@
 #include <asm/mach-imx/iomux-v3.h>
 #include <asm/mach-imx/video.h>
 
-#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
-        PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
-        PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-static iomux_v3_cfg_t const uart_pads[] = {
-#ifdef CONFIG_MX6QDL
-        IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-        IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-#elif CONFIG_MX6UL
-	IOMUX_PADS(PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL)),
-	IOMUX_PADS(PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL)),
-#endif
-};
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
@@ -421,12 +407,12 @@ void board_init_f(ulong dummy)
 	if (!(is_mx6ul()))
 		gpr_init();
 
-	/* iomux */
-	SETUP_IOMUX_PADS(uart_pads);
-
 	/* setup GP timer */
 	timer_init();
 
+	/* Enable device tree and early DM support*/
+	spl_early_init();
+
 	/* UART clocks enabled and gd valid - init serial console */
 	preloader_console_init();
 
configs/imx6dl_icore_nand_defconfig +1 -0
index fe4866e2f5..af5873a784 100644
@@ -66,6 +66,7 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
 CONFIG_VIDEO=y
configs/imx6q_icore_nand_defconfig +1 -0
index 2cb995e7ae..8535627049 100644
@@ -67,6 +67,7 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
 CONFIG_VIDEO=y
configs/imx6qdl_icore_mipi_defconfig +1 -0
index 90eb153c45..8dd5e89511 100644
@@ -74,5 +74,6 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
configs/imx6qdl_icore_mmc_defconfig +1 -0
index 9f6d29a268..46497fbde1 100644
@@ -90,6 +90,7 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
 CONFIG_VIDEO=y
configs/imx6qdl_icore_nand_defconfig +1 -0
index 2cb995e7ae..8535627049 100644
@@ -67,6 +67,7 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
 CONFIG_IMX_THERMAL=y
 CONFIG_VIDEO=y
configs/imx6qdl_icore_rqs_defconfig +1 -0
index ee2c597bcb..3bab6739d0 100644
@@ -72,4 +72,5 @@ CONFIG_FEC_MXC=y
 CONFIG_MII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
Signature · 1 line
2.25.1
#1 lore raw

Please review and comment on this changeset.

Regards
Suniel

#3 lore raw

PATCH 1/1 engicam: imx6: migrate to DM_SERIAL

In reply to Suniel Mahesh
Quoted 6 lines

From: Michael Trimarchi <[email protected]> Add the needed DT overrides and configs to enable UART in SPL.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,        Managing Director: Erika Unter  
HRB 165235 Munich,   Office: Kirchenstr.5, 82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================