mm-add-nodes=-arg-to-memoryreclaim.patch removed from -mm tree
The quilt patch titled
Subject: mm: add nodes= arg to memory.reclaim
has been removed from the -mm tree. Its filename was
mm-add-nodes=-arg-to-memoryreclaim.patch
This patch was dropped because it was merged into the mm-stable branch of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
------------------------------------------------------
From: Mina Almasry <[email protected]>
Subject: mm: add nodes= arg to memory.reclaim
Date: Fri, 2 Dec 2022 14:35:31 -0800
The nodes= arg instructs the kernel to only scan the given nodes for proactive reclaim. For example use cases, consider a 2 tier memory system:
nodes 0,1 -> top tier
nodes 2,3 -> second tier
$ echo "1m nodes=0" > memory.reclaim
This instructs the kernel to attempt to reclaim 1m memory from node 0. Since node 0 is a top tier node, demotion will be attempted first. This is useful to direct proactive reclaim to specific nodes that are under pressure.
$ echo "1m nodes=2,3" > memory.reclaim
This instructs the kernel to attempt to reclaim 1m memory in the second tier, since this tier of memory has no demotion targets the memory will be reclaimed.
$ echo "1m nodes=0,1" > memory.reclaim
Instructs the kernel to reclaim memory from the top tier nodes, which can be desirable according to the userspace policy if there is pressure on the top tiers. Since these nodes have demotion targets, the kernel will attempt demotion first.
Since commit 3f1509c57b1b ("Revert "mm/vmscan: never demote for memcg reclaim""), the proactive reclaim interface memory.reclaim does both reclaim and demotion. Reclaim and demotion incur different latency costs to the jobs in the cgroup. Demoted memory would still be addressable by the userspace at a higher latency, but reclaimed memory would need to incur a pagefault.
The 'nodes' arg is useful to allow the userspace to control demotion and reclaim independently according to its policy: if the memory.reclaim is called on a node with demotion targets, it will attempt demotion first; if it is called on a node without demotion targets, it will only attempt reclaim.
---
Documentation/admin-guide/cgroup-v2.rst | 15 ++-- include/linux/swap.h | 3 mm/memcontrol.c | 67 +++++++++++++++++----- mm/vmscan.c | 4 - 4 files changed, 68 insertions(+), 21 deletions(-)
Documentation/admin-guide/cgroup-v2.rst renamed from Documentation/admin-guide/cgroup-v2.rst~mm-add-nodes=-arg-to-memoryreclaim +9 -6
@@ -1245,17 +1245,13 @@ PAGE_SIZE multiple when read back. This is a simple interface to trigger memory reclaim in the target cgroup. - This file accepts a single key, the number of bytes to reclaim. - No nested keys are currently supported. + This file accepts a string which contains the number of bytes to + reclaim. Example:: echo "1G" > memory.reclaim - The interface can be later extended with nested keys to - configure the reclaim behavior. For example, specify the - type of memory to reclaim from (anon, file, ..). - Please note that the kernel can over or under reclaim from the target cgroup. If less bytes are reclaimed than the specified amount, -EAGAIN is returned.
@@ -1267,6 +1263,13 @@ PAGE_SIZE multiple when read back. This means that the networking layer will not adapt based on reclaim induced by memory.reclaim. + This file also allows the user to specify the nodes to reclaim from, + via the 'nodes=' key, for example:: + + echo "1G nodes=0,1" > memory.reclaim + + The above instructs the kernel to reclaim memory from nodes 0,1. + memory.peak A read-only single value file which exists on non-root cgroups.
include/linux/swap.h renamed from include/linux/swap.h~mm-add-nodes=-arg-to-memoryreclaim +2 -1
@@ -418,7 +418,8 @@ extern unsigned long try_to_free_pages(sextern unsigned long try_to_free_mem_cgroup_pages (struct mem_cgroup *memcg,unsigned long nr_pages,gfp_t gfp_mask, -unsigned int reclaim_options); +unsigned int reclaim_options, +nodemask_t *nodemask); extern unsigned long mem_cgroup_shrink_node(struct mem_cgroup *mem, gfp_t gfp_mask, bool noswap, pg_data_t *pgdat,
mm/memcontrol.c renamed from mm/memcontrol.c~mm-add-nodes=-arg-to-memoryreclaim +54 -13
130 lines not on this page · raw message
mm/vmscan.c renamed from mm/vmscan.c~mm-add-nodes=-arg-to-memoryreclaim +3 -1
@@ -6758,7 +6758,8 @@ unsigned long mem_cgroup_shrink_node(strunsigned long try_to_free_mem_cgroup_pages (struct mem_cgroup *memcg,unsigned long nr_pages,gfp_t gfp_mask, -unsigned int reclaim_options) +unsigned int reclaim_options, +nodemask_t *nodemask) {unsigned long nr_reclaimed;unsigned int noreclaim_flag;
@@ -6773,6 +6774,7 @@ unsigned long try_to_free_mem_cgroup_pag .may_unmap = 1, .may_swap = !!(reclaim_options & MEMCG_RECLAIM_MAY_SWAP), .proactive = !!(reclaim_options & MEMCG_RECLAIM_PROACTIVE), + .nodemask = nodemask, };/* * Traverse the ZONELIST_FALLBACK zonelist of the current node to put
_
Patches currently in -mm which might be from [email protected] are