Skip to contentSkip to conversation

TI's K3 documentation updates

PATCH In review Bryan Brattlof 3 participants 7 messages Dec 19, 2022 – Jan 5, 2023

lore
Share & tools
lore
#0 lore raw

cover TI's K3 documentation updates

Hello everyone!

Before the holidays get started, I wanted to improve the documentation for TI's K3 generation of SoCs. Specifically I wanted to collect all the similarities into one file called 'K3' in doc/board/ti/ and leave the details to each SoC specific sub-page.

My goal is to eliminate the boilerplate needed to document each new K3 SoC and instead allow the sub-pages to highlight the differences that could trip others as they begin to develop on their new K3 device.

Thanks for reviewing!
~Bryan

Bryan Brattlof (2):
doc: ti: reorganize existing ti docs
doc: ti: add the K3 generation page

 doc/board/ti/am335x_evm.rst |   5 +-
 doc/board/ti/am62x_sk.rst   |   4 +-
 doc/board/ti/index.rst      |   5 +-
 doc/board/ti/j721e_evm.rst  |   4 +-
 doc/board/ti/k3.rst         | 276 ++++++++++++++++++++++++++++++++++++
 5 files changed, 286 insertions(+), 8 deletions(-)
 create mode 100644 doc/board/ti/k3.rst

base-commit: 2243922edca9f56a9d5519b9d6e36f5d7a18434d

Signature · 1 line
2.39.0
#1 lore raw

PATCH 1/2 doc: ti: reorganize existing ti docs

Texas Instruments produces quite a lot of SoCs based upon a common architecture 'generation'. (eg: OMAP, K3) TI's existing documentation layout makes noticing this generation jump rather difficult.

To make navigation easier, split the existing documentation into individual SoC families so we may begin grouping them according to their generational (eg: OMAP, K3) families.

---
 doc/board/ti/am335x_evm.rst | 5 ++++-
 doc/board/ti/am62x_sk.rst   | 4 ++--
 doc/board/ti/j721e_evm.rst  | 4 ++--
 3 files changed, 8 insertions(+), 5 deletions(-)
doc/board/ti/am335x_evm.rst +4 -1
index a90f32da7aea5..7db9604ce05c9 100644
@@ -1,8 +1,11 @@
 .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 .. sectionauthor:: Tom Rini <[email protected]>
 
+AM335x Generation
+=================
+
 Summary
-=======
+-------
 
 This document covers various features of the `am335x_evm` default
 configuration, some of the related defconfigs, and how to enable hardware
doc/board/ti/am62x_sk.rst +2 -2
index 4e68c2018a50b..b1b7d99befb92 100644
@@ -1,8 +1,8 @@
 .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 .. sectionauthor:: Vignesh Raghavendra <[email protected]>
 
-Texas Instruments AM62 Platforms
-================================
+AM62 Platforms
+===============
 
 Introduction:
 -------------
doc/board/ti/j721e_evm.rst +2 -2
index ad70f15b7a418..e898601c41ea4 100644
@@ -1,8 +1,8 @@
 .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 .. sectionauthor:: Lokesh Vutla <[email protected]>
 
-Texas Instruments K3 Platforms
-==============================
+J721E Platforms
+===============
 
 Introduction:
 -------------
Signature · 1 line
2.39.0
#2 lore raw

Re: [PATCH 1/2] doc: ti: reorganize existing ti docs

Quoted 20 lines · Bryan Brattlof

Texas Instruments produces quite a lot of SoCs based upon a common architecture 'generation'. (eg: OMAP, K3) TI's existing documentation layout makes noticing this generation jump rather difficult.

To make navigation easier, split the existing documentation into individual SoC families so we may begin grouping them according to their generational (eg: OMAP, K3) families.

---
  doc/board/ti/am335x_evm.rst | 5 ++++-
  doc/board/ti/am62x_sk.rst   | 4 ++--
  doc/board/ti/j721e_evm.rst  | 4 ++--
  3 files changed, 8 insertions(+), 5 deletions(-)
doc/board/ti/am335x_evm.rst +0 -0
index a90f32da7aea5..7db9604ce05c9 100644

doc/board/ti/am335x_evm.rst line 5

Quoted 8 lines
doc/board/ti/am335x_evm.rst +3 -1
@@ -1,8 +1,11 @@
  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
  .. sectionauthor:: Tom Rini <[email protected]>
 
+AM335x Generation
+=================
+
  Summary
-=======

"AM335x Generation" is a level 1 header (<h1>). "Summary" should not be on the same header level. Please, use:

Summary
-------

Best regards

Heinrich

Quoted 34 lines
doc/board/ti/am335x_evm.rst +1 -0
+-------
 
  This document covers various features of the `am335x_evm` default
  configuration, some of the related defconfigs, and how to enable hardware
doc/board/ti/am62x_sk.rst +2 -2
index 4e68c2018a50b..b1b7d99befb92 100644
@@ -1,8 +1,8 @@
  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
  .. sectionauthor:: Vignesh Raghavendra <[email protected]>
 
-Texas Instruments AM62 Platforms
-================================
+AM62 Platforms
+===============
 
  Introduction:
  -------------
doc/board/ti/j721e_evm.rst +2 -2
index ad70f15b7a418..e898601c41ea4 100644
@@ -1,8 +1,8 @@
  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
  .. sectionauthor:: Lokesh Vutla <[email protected]>
 
-Texas Instruments K3 Platforms
-==============================
+J721E Platforms
+===============
 
  Introduction:
  -------------
#3 lore raw

Re: [PATCH 1/2] doc: ti: reorganize existing ti docs

Quoted 33 lines · Heinrich Schuchardt
Quoted 26 lines · Bryan Brattlof

Texas Instruments produces quite a lot of SoCs based upon a common architecture 'generation'. (eg: OMAP, K3) TI's existing documentation layout makes noticing this generation jump rather difficult.

To make navigation easier, split the existing documentation into individual SoC families so we may begin grouping them according to their generational (eg: OMAP, K3) families.

---
  doc/board/ti/am335x_evm.rst | 5 ++++-
  doc/board/ti/am62x_sk.rst   | 4 ++--
  doc/board/ti/j721e_evm.rst  | 4 ++--

  3 files changed, 8 insertions(+), 5 deletions(-)
doc/board/ti/am335x_evm.rst +0 -0
index a90f32da7aea5..7db9604ce05c9 100644
@@ -1,8 +1,11 @@

  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause .. sectionauthor:: Tom Rini <[email protected]>

doc/board/ti/am335x_evm.rst +3 -0
+AM335x Generation
+=================
+
Quoted 2 lines

  Summary
-=======

"AM335x Generation" is a level 1 header (<h1>). "Summary" should not be on the same header level. Please, use:

Quoted 2 lines

Summary
-------

Sorry misread the patch.

Quoted 41 lines

Best regards

Heinrich

Quoted 35 lines

+-------

  This document covers various features of the am335x_evm default configuration, some of the related defconfigs, and how to enable hardware

doc/board/ti/am62x_sk.rst +0 -0
index 4e68c2018a50b..b1b7d99befb92 100644
@@ -1,8 +1,8 @@

  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause .. sectionauthor:: Vignesh Raghavendra <[email protected]>

doc/board/ti/am62x_sk.rst +2 -2
-Texas Instruments AM62 Platforms
-================================
+AM62 Platforms
+===============

  Introduction:
  -------------

doc/board/ti/j721e_evm.rst +0 -0
index ad70f15b7a418..e898601c41ea4 100644
@@ -1,8 +1,8 @@

  .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause .. sectionauthor:: Lokesh Vutla <[email protected]>

doc/board/ti/j721e_evm.rst +2 -2
-Texas Instruments K3 Platforms
-==============================
+J721E Platforms
+===============

  Introduction:
  -------------

#4 lore raw

PATCH 2/2 doc: ti: add the K3 generation page

In reply to Bryan Brattlof

Texas Instrument's entire K3 generation of SoCs use much of the same frameworks and boot flow, especially at the uboot level. Though there are small differences introduced as each new K3 based SoC is developed and as the K3 generation matures that will also need to be documented.

Rather than copying the same documentation, with the small differences applicable to that specific SoC to a new page, introduce a new K3 page that can describe the general boot flow and design decisions for the entire K3 generation of chips, leaving the specifics for that particular SoC to a unique sub-page below this one.

---
 doc/board/ti/index.rst |   5 +-
 doc/board/ti/k3.rst    | 276 +++++++++++++++++++++++++++++++++++++++++
 2 files changed, 278 insertions(+), 3 deletions(-)
 create mode 100644 doc/board/ti/k3.rst
doc/board/ti/index.rst +2 -3
index 250d9242e82bb..89d537d195196 100644
@@ -1,11 +1,10 @@
 .. SPDX-License-Identifier: GPL-2.0+
 
 Texas Instruments
-=================
+#################
 
 .. toctree::
    :maxdepth: 2
 
    am335x_evm
-   j721e_evm
-   am62x_sk
+   k3
doc/board/ti/k3.rst new file +276 -0

276 lines not on this page · raw message

Signature · 1 line
2.39.0
#5 lore raw

Re: [PATCH 2/2] doc: ti: add the K3 generation page

Quoted 72 lines · Bryan Brattlof

Texas Instrument's entire K3 generation of SoCs use much of the same frameworks and boot flow, especially at the uboot level. Though there are small differences introduced as each new K3 based SoC is developed and as the K3 generation matures that will also need to be documented.

Rather than copying the same documentation, with the small differences applicable to that specific SoC to a new page, introduce a new K3 page that can describe the general boot flow and design decisions for the entire K3 generation of chips, leaving the specifics for that particular SoC to a unique sub-page below this one.

---
  doc/board/ti/index.rst |   5 +-
  doc/board/ti/k3.rst    | 276 +++++++++++++++++++++++++++++++++++++++++
  2 files changed, 278 insertions(+), 3 deletions(-)

create mode 100644 doc/board/ti/k3.rst

doc/board/ti/index.rst +2 -3
index 250d9242e82bb..89d537d195196 100644
@@ -1,11 +1,10 @@
  .. SPDX-License-Identifier: GPL-2.0+
 
  Texas Instruments
-=================
+#################
 
  .. toctree::
     :maxdepth: 2
 
     am335x_evm
-   j721e_evm
-   am62x_sk
+   k3
doc/board/ti/k3.rst new file +30 -0
new file mode 100644
index 0000000000000..9eeee41dde931
@@ -0,0 +1,276 @@
+.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+.. sectionauthor:: Bryan Brattlof <[email protected]>
+
+K3 Generation
+=============
+
+Summary
+-------
+
+Texas Instrument's K3 family of SoCs utilize a heterogeneous multicore
+and highly integrated device architecture targeted to maximize
+performance and power efficiency for a wide range of industrial,
+automotive and other broad market segments.
+
+Typically the processing cores and the peripherals for these devices are
+partitioned into three functional domains to provide ultra-low power
+modes as well as accommodating application and industrial safety systems
+on the same SoC.  These functional domains are typically called the:
+
+* Wakeup (WKUP) domain
+* Micro-controller (MCU) domain
+* Main domain
+
+For a more detailed view of what peripherals are attached to each
+domain, consult the device specific documentation.
+
+K3 Based SoCs
+-------------
+
+.. toctree::

doc/board/ti/k3.rst line 40

Quoted 10 lines
doc/board/ti/k3.rst new file +10 -0
+   :maxdepth: 1
+
+   j721e_evm
+   am62x_sk
+
+Boot Flow Overview
+------------------
+
+For all K3 SoCs the first core started will be inside the Security
+Management Subsystem (SMS) which will secure the device and start a core

This name (SMS, DMSC, HSM) changes over the K3 devices, how about just "Security Enclave".

doc/board/ti/k3.rst line 41

Quoted 1 line
doc/board/ti/k3.rst new file +1 -0
+in the wakeup domain to run the ROM code. ROM will then initialize the

Not always in the wakeup domain either.. Also what "ROM code", the "Security Enclave" also has ROM code, should refer to this second ROM as "Public ROM".

doc/board/ti/k3.rst line 43

Quoted 2 lines
doc/board/ti/k3.rst new file +2 -0
+boot media needed to load the binaries packaged inside `tiboot3.bin`,
+including a 32bit U-Boot SPL, (called the wakup SPL) that ROM will jump

Does anyone call it "wakeup SPL"? I'd call it R5 SPL everywhere.

doc/board/ti/k3.rst line 52

Quoted 9 lines
doc/board/ti/k3.rst new file +9 -0
+to after it has finished loading everything into internal SRAM.
+
+.. code-block:: text
+
+   |  WKUP Domain
+    ROM -> WKUP SPL ->
+
+The wakeup SPL, running on a wakeup domain core, will initialize DDR and
+any peripherals needed load the larger binaries inside the `tispl.bin`

Some of this is sounding specific to file-system based boot modes, might be good to pick a name for this blob, then point out what we expect it to be called when still on filesystems.

Quoted 4 lines
doc/board/ti/k3.rst new file +4 -0
+into DDR.  Once loaded the wakeup SPL will start one of the 'big'
+application cores inside the main domain to initialize the main domain,
+starting with ARM Trusted Firmware (ATF), before moving on to start
+OPTEE and the main domain's U-Boot SPL.

doc/board/ti/k3.rst line 66

Quoted 10 lines
doc/board/ti/k3.rst new file +10 -0
+
+.. code-block:: text
+
+   |  WKUP Domain   | Main Domain ->
+    ROM -> WKUP SPL -> ATF -> OPTEE -> Main SPL
+
+The main domain's SPL, running on a 64bit application core, has
+virtually unlimited space (billions of bytes now that DDR is working) to
+initialize even more peripherals needed to load in the `u-boot.img`
+which loads more firmware into the micro-controller & wakeup domains and

Also loads up cores in the MAIN domain, could be easier to make this generic.

doc/board/ti/k3.rst line 73

Quoted 7 lines
doc/board/ti/k3.rst new file +7 -0
+finally prepare the main domain to run Linux.
+
+.. code-block:: text
+
+   |  WKUP Domain   | Main Domain ->
+    ROM -> WKUP SPL -> ATF -> OPTEE -> Main SPL -> UBoot -> Linux
+

Could help to lay this out virtually, since the R5 core keeps running after the MAIN domain is running, it is not a direct execution handover.

doc/board/ti/k3.rst line 86

Quoted 13 lines
doc/board/ti/k3.rst new file +13 -0
+This is the typical boot flow for all K3 based SoCs, however this flow
+offers quite a lot in the terms of flexibility, especially on High
+Security (HS) SoCs.
+
+Boot Flow Variations
+^^^^^^^^^^^^^^^^^^^^
+
+All K3 SoCs will generally use the above boot flow with two main
+differences depending on the capabilities of the boot ROM and the number
+of cores inside the device. These differences split the bootflow into
+essentially 4 unique but very similar flows:
+
+* Split binary with a combined firmware: (eg: AM65)

What binary/firmware is split, you have not talked about SYSFW/TIFS/DM at this point yet..

Quoted 5 lines
doc/board/ti/k3.rst new file +5 -0
+* Combined binary with a combined firmware: (eg: AM64)
+* Split binary with a split firmware: (eg: J721E)
+* Combined binary with a split firmware: (eg: AM62)
+
+For devices that utilize the split binary approach, ROM is not capable

doc/board/ti/k3.rst line 101

Quoted 10 lines
doc/board/ti/k3.rst new file +10 -0
+of loading the firmware into the SoC requiring the wakeup domain's
+U-Boot SPL to load the firmware.
+
+Devices with a split firmware will have two firmwares loaded into the
+device at different times during the bootup process. TI's Foundational
+Security (TIFS), needed to operate the Security Management Subsystem,
+will either be loaded by ROM or the WKUP U-Boot SPL, then once the
+wakeup U-Boot SPL has completed, the second Device Management (DM)
+firmware can be loaded on the now free core in the wakeup domain.
+

Could help to draw this one out visually.

Quoted 77 lines
doc/board/ti/k3.rst new file +77 -0
+For more information on the bootup process of your SoC, consult the
+device specific boot flow documentation.
+
+Software Sources
+----------------
+
+All scripts and code needed to build the `tiboot3.bin`, `tispl.bin` and
+`u-boot.img` for all K3 SoCs can be located at the following places
+online
+
+* **Das U-Boot**
+
+  | **source:** https://source.denx.de/u-boot/u-boot.git
+  | **branch:** master
+
+* **K3 Image Gen**
+
+  | **source:** https://git.ti.com/git/k3-image-gen/k3-image-gen.git
+  | **branch:** master
+
+* **ARM Trusted Firmware (ATF)**
+
+  | **source:** https://github.com/ARM-software/arm-trusted-firmware.git
+  | **branch:** master
+
+* **Open Portable Trusted Execution Environment (OPTEE)**
+
+  | **source:** https://github.com/OP-TEE/optee_os.git
+  | **branch:** master
+
+* **TI Firmware (TIFS, DM, DSMC)**
+
+  | **source:** https://git.ti.com/git/processor-firmware/ti-linux-firmware.git
+  | **branch:** ti-linux-firmware
+
+* **TI's Security Development Tools**
+
+  | **source:** https://git.ti.com/git/security-development-tools/core-secdev-k3.git
+  | **branch:** master
+
+Build Procedure
+---------------
+
+Depending on the specifics of your device, you will need three or more
+binaries to boot your SoC.
+
+* `tiboot3.bin` (bootloader for the wakeup domain)
+* `tispl.bin` (bootloader for the main domain)
+* `u-boot.img`
+
+During the bootup process, both the 32bit wakeup domain and the 64bit
+main domains will be involved. This means everything inside the
+`tiboot3.bin` running in the wakeup domain will need to be compiled for
+32bit cores and most binaries in the `tispl.bin` will need to be
+compiled for 64bit main domain CPU cores.
+
+All of that to say you will need both a 32bit and 64bit cross compiler
+(assuming you're using an x86 desktop)
+
+.. code-block:: bash
+
+   export CC32=arm-linux-gnueabihf-
+   export CC64=aarch64-linux-gnu-
+
+Building tiboot3.bin
+^^^^^^^^^^^^^^^^^^^^^
+
+1. To generate the U-Boot SPL for the wakeup domain, use the following
+   commands, substituting :code:`{SOC}` for the name of your device (eg:
+   am62x)
+
+.. code-block:: bash
+
+   # inside u-boot source
+   make ARCH=arm O=build/wkup CROSS_COMPILE=$CC32 {SOC}_evm_r5_defconfig
+   make ARCH=arm O=build/wkup CROSS_COMPILE=$CC32
+

doc/board/ti/k3.rst line 188

Quoted 10 lines
doc/board/ti/k3.rst new file +10 -0
+2. Next we will use the K3 Image Gen scripts to package the various
+   firmware and the wakeup UBoot SPL into the final `tiboot3.bin`
+   binary. (or the `sysfw.itb` if your device uses the split binary
+   flow)
+
+.. code-block:: bash
+
+   # inside k3-image-gen source
+   make CROSS_COMPILE=$CC32 SOC={SOC} SOC_TYPE={hs,gp} \
+        TI_SECURE_DEV_PKG=<path/to/securit-development-tools> \

s/securit/security

Andrew

Quoted 88 lines
doc/board/ti/k3.rst new file +88 -0
+        SYSFW_PATH=<path/to/ti-sysfw/ti-fs-firmware-{SOC}-{hs|gp}.bin> \
+        SYSFW_HS_INNER_CERT_PATH=<path/to/ti-sysfw/ti-fs-firmware-{SOC}-hs-cert.bin
+
+For devices that use the *combined binary flow*, you will also need to
+supply the location of the SPL we created in step 1 above, so it can be
+packaged into the final `tiboot3.bin`.
+
+.. code-block:: bash
+
+   SBL=<path/to/wakeup/u-boot-spl.bin>
+
+At this point you should have all the needed binaries to boot the wakeup
+domain of your K3 SoC.
+
+**Combined Binary Boot Flow** (eg: am62x, am64x, ... )
+
+   `k3-image-gen/tiboot3-{SOC}-{hs,gp}-evm.bin`
+
+**Split Binary Boot Flow** (eg: j721e, am65x)
+
+   | `u-boot/build/wkup/tiboot3.bin`
+   | `k3-image-gen/sysfw-{SOC}-evm.bin`
+
+.. note ::
+
+   It's important to rename the generated `tiboot3.bin` and `sysfw.itb`
+   to match exactly `tiboot3.bin` and `sysfw.itb` as ROM and the wakeup
+   UBoot SPL will only look for and load the files with these names.
+
+Building tispl.bin
+^^^^^^^^^^^^^^^^^^^
+
+The `tispl.bin` is a standard fitImage combining the firmware need for
+the main domain to function properly as well as Device Management (DM)
+firmware if your device using a split firmware.
+
+3. We will first need ATF, as it's the first thing to run on the 'big'
+   application cores on the main domain.
+
+.. code-block:: bash
+
+   # inside arm-trusted-firmware source
+   make CROSS_COMPILE=$CC64 ARCH=aarch64 PLAT=k3 \
+        TARGET_BOARD={lite|generic} \
+        SPD=opteed \
+
+Typically all `j7*` devices will use `TARGET_BOARD=generic` while all
+Sitara (`am6*`) devices use the `lite` option.
+
+4. The Open Portable Trusted Execution Environment (OPTEE) is designed
+   to run as a companion to a non-secure Linux kernel for Cortex-A cores
+   using the TrustZone technology built into the core.
+
+.. code-block:: bash
+
+   # inside optee_os source
+   make CROSS_COMPILE=$CC32 CROSS_COMPILE64=$CC64 \
+        PLATFORM=k3 CFG_ARM64_core=y
+
+5. Finally, after ATF has initialized the main domain and OPTEE has
+   finished, we can jump back into U-Boot again, this time running on a
+   64bit core in the main domain.
+
+.. code-block:: bash
+
+   # inside u-boot source
+   make ARCH=arm O=build/main CROSS_COMPILE=$CC64 {SOC}_evm_a{53,72}_defconfig
+   make ARCH=arm O=build/main CROSS_COMPILE=$CC64 \
+        ATF=<path/to/atf/bl31.bin \
+        TEE=<path/to/optee/tee-pager_v2.bin
+
+If your device uses a split firmware, you will also need to supply the
+path to the Device Management (DM) Firmware to be included in the final
+`tispl.bin` binary
+
+.. code-block:: bash
+
+   DM=<path/to/ti-linux-firmware/ti-dm/ipc_echo_testb_mcu1_0_release_strip.xer5f>
+
+At this point you should have every binary needed initialize both the
+wakeup and main domain and to boot to the U-Boot prompt
+
+**Main Domain Bootloader**
+
+   | `u-boot/build/main/tispl.bin`
+   | `u-boot/build/main/u-boot.img`
+
+
#6 lore raw

Re: [PATCH 2/2] doc: ti: add the K3 generation page

Hi Andrew!

On January 3, 2023 thus sayeth Andrew Davis:

Quoted 14 lines · Bryan Brattlof
Quoted 13 lines

Texas Instrument's entire K3 generation of SoCs use much of the same frameworks and boot flow, especially at the uboot level. Though there are small differences introduced as each new K3 based SoC is developed and as the K3 generation matures that will also need to be documented.

Rather than copying the same documentation, with the small differences applicable to that specific SoC to a new page, introduce a new K3 page that can describe the general boot flow and design decisions for the entire K3 generation of chips, leaving the specifics for that particular SoC to a unique sub-page below this one.

---

...

Quoted 11 lines

doc/board/ti/k3.rst line 40

Quoted 6 lines
doc/board/ti/k3.rst new file +6 -0
+
+Boot Flow Overview
+------------------
+
+For all K3 SoCs the first core started will be inside the Security
+Management Subsystem (SMS) which will secure the device and start a core

This name (SMS, DMSC, HSM) changes over the K3 devices, how about just "Security Enclave".

Good point... I'll get this updated.

Quoted 5 lines
Quoted 1 line

+in the wakeup domain to run the ROM code. ROM will then initialize the

Not always in the wakeup domain either.. Also what "ROM code", the "Security Enclave" also has ROM code, should refer to this second ROM as "Public ROM".

True and I was trying to keep Public vs Private ROM out of this, but I'm good with this if you are :)

Quoted 5 lines

doc/board/ti/k3.rst line 43

Quoted 2 lines
doc/board/ti/k3.rst new file +2 -0
+boot media needed to load the binaries packaged inside `tiboot3.bin`,
+including a 32bit U-Boot SPL, (called the wakup SPL) that ROM will jump

Does anyone call it "wakeup SPL"? I'd call it R5 SPL everywhere.

haha I started calling it the wakup spl because calling it the r5 spl felt too specific

Quoted 5 lines
Quoted 5 lines
doc/board/ti/k3.rst new file +5 -0
+to after it has finished loading everything into internal SRAM.
+
+.. code-block:: text
+
+   |  WKUP Domain
Quoted 9 lines

doc/board/ti/k3.rst line 52

Quoted 4 lines
doc/board/ti/k3.rst new file +4 -0
+    ROM -> WKUP SPL ->
+
+The wakeup SPL, running on a wakeup domain core, will initialize DDR and
+any peripherals needed load the larger binaries inside the `tispl.bin`

Some of this is sounding specific to file-system based boot modes, might be good to pick a name for this blob, then point out what we expect it to be called when still on filesystems.

Ah that's true. I think I can do that

Quoted 8 lines
Quoted 8 lines
doc/board/ti/k3.rst new file +8 -0
+into DDR.  Once loaded the wakeup SPL will start one of the 'big'
+application cores inside the main domain to initialize the main domain,
+starting with ARM Trusted Firmware (ATF), before moving on to start
+OPTEE and the main domain's U-Boot SPL.
+
+.. code-block:: text
+
+   |  WKUP Domain   | Main Domain ->
Quoted 9 lines

doc/board/ti/k3.rst line 66

Quoted 6 lines
doc/board/ti/k3.rst new file +6 -0
+    ROM -> WKUP SPL -> ATF -> OPTEE -> Main SPL
+
+The main domain's SPL, running on a 64bit application core, has
+virtually unlimited space (billions of bytes now that DDR is working) to
+initialize even more peripherals needed to load in the `u-boot.img`
+which loads more firmware into the micro-controller & wakeup domains and

Also loads up cores in the MAIN domain, could be easier to make this generic.

Didn't think many people used that unprofessional hobby project ;)

Quoted 11 lines

doc/board/ti/k3.rst line 73

Quoted 7 lines
doc/board/ti/k3.rst new file +7 -0
+finally prepare the main domain to run Linux.
+
+.. code-block:: text
+
+   |  WKUP Domain   | Main Domain ->
+    ROM -> WKUP SPL -> ATF -> OPTEE -> Main SPL -> UBoot -> Linux
+

Could help to lay this out virtually, since the R5 core keeps running after the MAIN domain is running, it is not a direct execution handover.

Ah that's a good idea, kinda like what we already have for the am62x documentation.

Quoted 7 lines
Quoted 7 lines
doc/board/ti/k3.rst new file +7 -0
+This is the typical boot flow for all K3 based SoCs, however this flow
+offers quite a lot in the terms of flexibility, especially on High
+Security (HS) SoCs.
+
+Boot Flow Variations
+^^^^^^^^^^^^^^^^^^^^
+
Quoted 9 lines

doc/board/ti/k3.rst line 86

Quoted 6 lines
doc/board/ti/k3.rst new file +6 -0
+All K3 SoCs will generally use the above boot flow with two main
+differences depending on the capabilities of the boot ROM and the number
+of cores inside the device. These differences split the bootflow into
+essentially 4 unique but very similar flows:
+
+* Split binary with a combined firmware: (eg: AM65)

What binary/firmware is split, you have not talked about SYSFW/TIFS/DM at this point yet..

Oh good point... This could use a reordering.

Quoted 9 lines
Quoted 9 lines
doc/board/ti/k3.rst new file +9 -0
+* Combined binary with a combined firmware: (eg: AM64)
+* Split binary with a split firmware: (eg: J721E)
+* Combined binary with a split firmware: (eg: AM62)
+
+For devices that utilize the split binary approach, ROM is not capable
+of loading the firmware into the SoC requiring the wakeup domain's
+U-Boot SPL to load the firmware.
+
+Devices with a split firmware will have two firmwares loaded into the
Quoted 9 lines

doc/board/ti/k3.rst line 101

Quoted 6 lines
doc/board/ti/k3.rst new file +6 -0
+device at different times during the bootup process. TI's Foundational
+Security (TIFS), needed to operate the Security Management Subsystem,
+will either be loaded by ROM or the WKUP U-Boot SPL, then once the
+wakeup U-Boot SPL has completed, the second Device Management (DM)
+firmware can be loaded on the now free core in the wakeup domain.
+

Could help to draw this one out visually.

Yeah more visuals couldn't hurt

Quoted 9 lines

doc/board/ti/k3.rst line 188

Quoted 6 lines
doc/board/ti/k3.rst new file +6 -0
+
+.. code-block:: bash
+
+   # inside k3-image-gen source
+   make CROSS_COMPILE=$CC32 SOC={SOC} SOC_TYPE={hs,gp} \
+        TI_SECURE_DEV_PKG=<path/to/securit-development-tools> \

s/securit/security

Good catch!

Thanks for the review Andrew!
~Bryan