Skip to contentSkip to conversation

media: ov13b10: Support device probe in non-zero ACPI D state

PATCH In review Arec Kao 2 participants 2 messages Mar 14, 2023

Subsystems (3)
lore
Share & tools
lore

Arec Kao

author maintainer
#0 lore raw

PATCH v2 1/1 media: ov13b10: Support device probe in non-zero ACPI D state

Tell ACPI device PM code that the driver supports the device being in non-zero ACPI D state when the driver's probe function is entered.

Also do identification on the first access of the device, whether in probe or when starting streaming.

---
 drivers/media/i2c/ov13b10.c | 74 +++++++++++++++++++++++--------------
 1 file changed, 47 insertions(+), 27 deletions(-)
drivers/media/i2c/ov13b10.c +47 -27
index 549e5d93e568..722f490f9db4 100644
@@ -589,6 +589,9 @@ struct ov13b10 {
 
 	/* Streaming on/off */
 	bool streaming;
+
+	/* True if the device has been identified */
+	bool identified;
 };
 
 #define to_ov13b10(_sd)	container_of(_sd, struct ov13b10, sd)
@@ -1023,12 +1026,42 @@ ov13b10_set_pad_format(struct v4l2_subdev *sd,
 	return 0;
 }
 
+/* Verify chip ID */
+static int ov13b10_identify_module(struct ov13b10 *ov13b)
+{
+	struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
+	int ret;
+	u32 val;
+
+	if (ov13b->identified)
+		return 0;
+
+	ret = ov13b10_read_reg(ov13b, OV13B10_REG_CHIP_ID,
+			       OV13B10_REG_VALUE_24BIT, &val);
+	if (ret)
+		return ret;
+
+	if (val != OV13B10_CHIP_ID) {
+		dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
+			OV13B10_CHIP_ID, val);
+		return -EIO;
+	}
+
+	ov13b->identified = true;
+
+	return 0;
+}
+
 static int ov13b10_start_streaming(struct ov13b10 *ov13b)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
 	const struct ov13b10_reg_list *reg_list;
 	int ret, link_freq_index;
 
+	ret = ov13b10_identify_module(ov13b);
+	if (ret)
+		return ret;
+
 	/* Get out of from software reset */
 	ret = ov13b10_write_reg(ov13b, OV13B10_REG_SOFTWARE_RST,
 				OV13B10_REG_VALUE_08BIT, OV13B10_SOFTWARE_RST);
@@ -1144,27 +1177,6 @@ static int __maybe_unused ov13b10_resume(struct device *dev)
 	return ret;
 }
 
-/* Verify chip ID */
-static int ov13b10_identify_module(struct ov13b10 *ov13b)
-{
-	struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
-	int ret;
-	u32 val;
-
-	ret = ov13b10_read_reg(ov13b, OV13B10_REG_CHIP_ID,
-			       OV13B10_REG_VALUE_24BIT, &val);
-	if (ret)
-		return ret;
-
-	if (val != OV13B10_CHIP_ID) {
-		dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
-			OV13B10_CHIP_ID, val);
-		return -EIO;
-	}
-
-	return 0;
-}
-
 static const struct v4l2_subdev_video_ops ov13b10_video_ops = {
 	.s_stream = ov13b10_set_stream,
 };
@@ -1379,6 +1391,7 @@ static int ov13b10_check_hwcfg(struct device *dev)
 static int ov13b10_probe(struct i2c_client *client)
 {
 	struct ov13b10 *ov13b;
+	bool full_power;
 	int ret;
 
 	/* Check HW config */
@@ -1395,11 +1408,14 @@ static int ov13b10_probe(struct i2c_client *client)
 	/* Initialize subdev */
 	v4l2_i2c_subdev_init(&ov13b->sd, client, &ov13b10_subdev_ops);
 
-	/* Check module identity */
-	ret = ov13b10_identify_module(ov13b);
-	if (ret) {
-		dev_err(&client->dev, "failed to find sensor: %d\n", ret);
-		return ret;
+	full_power = acpi_dev_state_d0(&client->dev);
+	if (full_power) {
+		/* Check module identity */
+		ret = ov13b10_identify_module(ov13b);
+		if (ret) {
+			dev_err(&client->dev, "failed to find sensor: %d\n", ret);
+			return ret;
+		}
 	}
 
 	/* Set default mode to max resolution */
@@ -1431,7 +1447,10 @@ static int ov13b10_probe(struct i2c_client *client)
 	 * Device is already turned on by i2c-core with ACPI domain PM.
 	 * Enable runtime PM and turn off the device.
 	 */
-	pm_runtime_set_active(&client->dev);
+
+	/* Set the device's state to active if it's in D0 state. */
+	if (full_power)
+		pm_runtime_set_active(&client->dev);
 	pm_runtime_enable(&client->dev);
 	pm_runtime_idle(&client->dev);
 
@@ -1480,6 +1499,7 @@ static struct i2c_driver ov13b10_i2c_driver = {
 	},
 	.probe_new = ov13b10_probe,
 	.remove = ov13b10_remove,
+	.flags = I2C_DRV_ACPI_WAIVE_D0_PROBE,
 };
 
 module_i2c_driver(ov13b10_i2c_driver);
Signature · 1 line
2.17.1
maintainer
#1 lore raw

Hi Arec,

Quoted 7 lines · Arec Kao

Tell ACPI device PM code that the driver supports the device being in non-zero ACPI D state when the driver's probe function is entered.

Also do identification on the first access of the device, whether in probe or when starting streaming.

Please detail the changes from the previous version.

This is ok for now though.

Signature · 3 lines
Kind regards,

Sakari Ailus