ACPI: SPCR: Amend indentation
PATCH v2 1/1 ACPI: SPCR: Amend indentation
1) Remove unnecessary blank lines.
2) Reformat one comment for consistency.
Signed-off-by Andy Shevchenko <[email protected]>
---
v2: avoided changind double spaces (Rafael)
drivers/acpi/spcr.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)
drivers/acpi/spcr.c +3 -6
@@ -71,7 +71,6 @@ static bool xgene_8250_erratum_present(struct acpi_table_spcr *tb)/** * acpi_parse_spcr() - parse ACPI SPCR table and add preferred console -* * @enable_earlycon: set up earlycon for the console specified by the table * @enable_console: setup the console specified by the table. *
@@ -82,7 +81,6 @@ static bool xgene_8250_erratum_present(struct acpi_table_spcr *tb)* * When CONFIG_ACPI_SPCR_TABLE is defined, this function should be called * from arch initialization code as soon as the DT/ACPI decision is made. -* */ int __init acpi_parse_spcr (bool enable_earlycon,bool enable_console) {
@@ -97,9 +95,7 @@ int __init acpi_parse_spcr(bool enable_earlycon, bool enable_console)if (acpi_disabled)return -ENODEV ; - status =acpi_get_table (ACPI_SIG_SPCR ,0 , - (struct acpi_table_header **)&table); - + status =acpi_get_table (ACPI_SIG_SPCR ,0 , (struct acpi_table_header **)&table);if (ACPI_FAILURE (status))return -ENOENT ;
@@ -202,7 +198,8 @@ int __init acpi_parse_spcr(bool enable_earlycon, bool enable_console)if (xgene_8250_erratum_present (table)) { iotype ="mmio32" ; -/* for xgene v1 and v2 we don't know the clock rate of the +/* +* For xgene v1 and v2 we don't know the clock rate of the * UART so don't attempt to change to the baud rate state * in the table because driver cannot calculate the dividers */
Signature · 1 line
2.40.0.1.gaa8946217a0b
Quoted 42 lines · Andy Shevchenko
1) Remove unnecessary blank lines.
2) Reformat one comment for consistency.Signed-off-by Andy Shevchenko <[email protected]>---
v2: avoided changind double spaces (Rafael)drivers/acpi/spcr.c | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-)drivers/acpi/spcr.c +1
-5@@ -71,7 +71,6 @@ static bool xgene_8250_erratum_present(struct acpi_table_spcr *tb)/** * acpi_parse_spcr() - parse ACPI SPCR table and add preferred console -* * @enable_earlycon: set up earlycon for the console specified by the table * @enable_console: setup the console specified by the table. * @@ -82,7 +81,6 @@ static bool xgene_8250_erratum_present(struct acpi_table_spcr *tb)* * When CONFIG_ACPI_SPCR_TABLE is defined, this function should be called * from arch initialization code as soon as the DT/ACPI decision is made. -* */ int __init acpi_parse_spcr (bool enable_earlycon,bool enable_console) {@@ -97,9 +95,7 @@ int __init acpi_parse_spcr(bool enable_earlycon, bool enable_console)if (acpi_disabled)return -ENODEV ; - status =acpi_get_table (ACPI_SIG_SPCR ,0 , - (struct acpi_table_header **)&table); - + status =acpi_get_table (ACPI_SIG_SPCR ,0 , (struct acpi_table_header **)&table);if (ACPI_FAILURE (status))return -ENOENT ;
drivers/acpi/spcr.c int __init acpi_parse_spcr(bool enable_earlycon, bool enable_console)
Quoted 10 lines
drivers/acpi/spcr.c +2
-2@@ -202,7 +198,8 @@ int __init acpi_parse_spcr(bool enable_earlycon, bool enable_console)if (xgene_8250_erratum_present (table)) { iotype ="mmio32" ; -/* for xgene v1 and v2 we don't know the clock rate of the +/* +* For xgene v1 and v2 we don't know the clock rate of the * UART so don't attempt to change to the baud rate state * in the table because driver cannot calculate the dividers */ --
Applied as 6.4 material, thanks!