Skip to contentSkip to conversation

Add ethernet driver for StarFive JH7110 SoC

PATCH Superseded Yanhong Wang 3 participants 9 messages Mar 29, 2023 – Apr 2, 2023

Subsystems (4)

v2 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v2 cover Add ethernet driver for StarFive JH7110 SoC

This series adds ethernet support for the StarFive JH7110 RISC-V SoC. The series includes PHY and MAC drivers. The PHY model is YT8531 (from Motorcomm Inc), and the MAC version is dwmac-5.20 (from Synopsys DesignWare).

The implementation of the phy driver is ported from linux, but it has been adjusted for the u-boot framework.

The PHY and MAC driver has been tested on the StarFive VisionFive 2 1.2A and 1.3B boards and works normally.

For more information and support,you can visit RVspace wiki[1].

This patchset should be applied after the patchset [2].
[1] https://wiki.rvspace.org/
[2] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/

v2:
- Reworded the phy driver. Added platform private data struct to save the configuration data read from dts.
- Reworded the MAC driver. Added platform private data struct to save the configuration data read from dts.

Previous versions:
v1 - https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/

Yanhong Wang (5):
net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy
net: dwc_eth_qos: Add StarFive ethernet driver glue layer
riscv: dts: jh7110: Add ethernet device tree nodes
riscv: dts: starfive: Add phy clock delay configuration for StarFive
VisionFive2 board
configs: starfive: Enable ethernet configuration for StarFive
VisionFive 2

 .../jh7110-starfive-visionfive-2-v1.2a.dts    |  13 +
 .../jh7110-starfive-visionfive-2-v1.3b.dts    |  27 ++
 .../dts/jh7110-starfive-visionfive-2.dtsi     |  34 ++
 arch/riscv/dts/jh7110.dtsi                    |  69 +++
 configs/starfive_visionfive2_12a_defconfig    |  12 +-
 configs/starfive_visionfive2_13b_defconfig    |  12 +-
 drivers/net/Kconfig                           |   7 +
 drivers/net/Makefile                          |   1 +
 drivers/net/dwc_eth_qos.c                     |   6 +
 drivers/net/dwc_eth_qos.h                     |   1 +
 drivers/net/dwc_eth_qos_starfive.c            | 249 ++++++++++
 drivers/net/phy/Kconfig                       |   6 +
 drivers/net/phy/Makefile                      |   1 +
 drivers/net/phy/motorcomm.c                   | 450 ++++++++++++++++++
 drivers/net/phy/phy.c                         |   4 +-
 include/phy.h                                 |   1 +
 16 files changed, 890 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/dwc_eth_qos_starfive.c
 create mode 100644 drivers/net/phy/motorcomm.c

base-commit: d7c2e87a0b8025314ae7dd62a8add292b7524e0b

Signature · 1 line
2.17.1
#1 lore raw

PATCH v2 1/5 net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have verified the driver on StarFive VisionFive2 board.

---
 drivers/net/phy/Kconfig     |   6 +
 drivers/net/phy/Makefile    |   1 +
 drivers/net/phy/motorcomm.c | 450 ++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy.c       |   4 +-
 include/phy.h               |   1 +
 5 files changed, 461 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/phy/motorcomm.c
drivers/net/phy/Kconfig +6 -0
index 5eaff053a0..aba718566a 100644
@@ -212,6 +212,12 @@ config PHY_MICREL_KSZ8XXX
 
 endif # PHY_MICREL
 
+config PHY_MOTORCOMM
+	tristate "Motorcomm PHYs"
+	help
+	  Enables support for Motorcomm network PHYs.
+	  Currently supports the YT8531 Gigabit Ethernet PHYs.
+
 config PHY_MSCC
 	bool "Microsemi Corp Ethernet PHYs support"
 
drivers/net/phy/Makefile +1 -0
index d38e99e717..e9523fed2e 100644
@@ -23,6 +23,7 @@ obj-$(CONFIG_PHY_MARVELL) += marvell.o
 obj-$(CONFIG_PHY_MICREL_KSZ8XXX) += micrel_ksz8xxx.o
 obj-$(CONFIG_PHY_MICREL_KSZ90X1) += micrel_ksz90x1.o
 obj-$(CONFIG_PHY_MESON_GXL) += meson-gxl.o
+obj-$(CONFIG_PHY_MOTORCOMM) += motorcomm.o
 obj-$(CONFIG_PHY_NATSEMI) += natsemi.o
 obj-$(CONFIG_PHY_NXP_C45_TJA11XX) += nxp-c45-tja11xx.o
 obj-$(CONFIG_PHY_NXP_TJA11XX) += nxp-tja11xx.o
drivers/net/phy/motorcomm.c new file +450 -0

450 lines not on this page · raw message

drivers/net/phy/phy.c +3 -1
index 80230b907c..78bde61798 100644
@@ -570,6 +570,9 @@ int phy_init(void)
 #endif
 #ifdef CONFIG_PHY_XILINX_GMII2RGMII
 	phy_xilinx_gmii2rgmii_init();
+#endif
+#ifdef CONFIG_PHY_MOTORCOMM
+	phy_motorcomm_init();
 #endif
 	genphy_init();
 
@@ -755,7 +758,6 @@ static struct phy_device *create_phy_by_mask(struct mii_dev *bus,
 	while (phy_mask) {
 		int addr = ffs(phy_mask) - 1;
 		int r = get_phy_id(bus, addr, devad, &phy_id);
-
 		/*
 		 * If the PHY ID is flat 0 we ignore it.  There are C45 PHYs
 		 * that return all 0s for C22 reads (like Aquantia AQR112) and
include/phy.h +1 -0
index 87aa86c2e7..f7bb2fe0af 100644
@@ -344,6 +344,7 @@ int phy_mscc_init(void);
 int phy_fixed_init(void);
 int phy_ncsi_init(void);
 int phy_xilinx_gmii2rgmii_init(void);
+int phy_motorcomm_init(void);
 
 int board_phy_config(struct phy_device *phydev);
 int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id);
Signature · 1 line
2.17.1
Reviewed-by on v2 1/5
#2 lore raw

Re: [PATCH v2 1/5] net: phy: Add driver for Motorcomm yt8531 gigabit ethernet phy

Quoted 534 lines · Yanhong Wang

Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have verified the driver on StarFive VisionFive2 board.

---
 drivers/net/phy/Kconfig     |   6 +
 drivers/net/phy/Makefile    |   1 +
 drivers/net/phy/motorcomm.c | 450 ++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy.c       |   4 +-
 include/phy.h               |   1 +
 5 files changed, 461 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/phy/motorcomm.c
drivers/net/phy/Kconfig +6 -0
index 5eaff053a0..aba718566a 100644
@@ -212,6 +212,12 @@ config PHY_MICREL_KSZ8XXX
 
 endif # PHY_MICREL
 
+config PHY_MOTORCOMM
+       tristate "Motorcomm PHYs"
+       help
+         Enables support for Motorcomm network PHYs.
+         Currently supports the YT8531 Gigabit Ethernet PHYs.
+
 config PHY_MSCC
        bool "Microsemi Corp Ethernet PHYs support"
 
drivers/net/phy/Makefile +1 -0
index d38e99e717..e9523fed2e 100644
@@ -23,6 +23,7 @@ obj-$(CONFIG_PHY_MARVELL) += marvell.o
 obj-$(CONFIG_PHY_MICREL_KSZ8XXX) += micrel_ksz8xxx.o
 obj-$(CONFIG_PHY_MICREL_KSZ90X1) += micrel_ksz90x1.o
 obj-$(CONFIG_PHY_MESON_GXL) += meson-gxl.o
+obj-$(CONFIG_PHY_MOTORCOMM) += motorcomm.o
 obj-$(CONFIG_PHY_NATSEMI) += natsemi.o
 obj-$(CONFIG_PHY_NXP_C45_TJA11XX) += nxp-c45-tja11xx.o
 obj-$(CONFIG_PHY_NXP_TJA11XX) += nxp-tja11xx.o
drivers/net/phy/motorcomm.c new file +450 -0
new file mode 100644
index 0000000000..6e37700adc
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Motorcomm 8531 PHY driver.
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <phy.h>
+#include <linux/bitfield.h>
+
+#define PHY_ID_YT8531                          0x4f51e91b
+#define PHY_ID_MASK                            GENMASK(31, 0)
+
+/* Extended Register's Address Offset Register */
+#define YTPHY_PAGE_SELECT                      0x1E
+
+/* Extended Register's Data Register */
+#define YTPHY_PAGE_DATA                        0x1F
+
+#define YTPHY_SYNCE_CFG_REG                    0xA012
+
+#define YTPHY_DTS_OUTPUT_CLK_DIS               0
+#define YTPHY_DTS_OUTPUT_CLK_25M               25000000
+#define YTPHY_DTS_OUTPUT_CLK_125M              125000000
+
+#define YT8531_SCR_SYNCE_ENABLE                BIT(6)
+/* 1b0 output 25m clock   *default*
+ * 1b1 output 125m clock
+ */
+#define YT8531_SCR_CLK_FRE_SEL_125M            BIT(4)
+#define YT8531_SCR_CLK_SRC_MASK                GENMASK(3, 1)
+#define YT8531_SCR_CLK_SRC_PLL_125M            0
+#define YT8531_SCR_CLK_SRC_UTP_RX              1
+#define YT8531_SCR_CLK_SRC_SDS_RX              2
+#define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL  3
+#define YT8531_SCR_CLK_SRC_REF_25M             4
+#define YT8531_SCR_CLK_SRC_SSC_25M             5
+
+/* 1b0 use original tx_clk_rgmii  *default*
+ * 1b1 use inverted tx_clk_rgmii.
+ */
+#define YT8531_RC1R_TX_CLK_SEL_INVERTED        BIT(14)
+#define YT8531_RC1R_RX_DELAY_MASK              GENMASK(13, 10)
+#define YT8531_RC1R_FE_TX_DELAY_MASK           GENMASK(7, 4)
+#define YT8531_RC1R_GE_TX_DELAY_MASK           GENMASK(3, 0)
+#define YT8531_RC1R_RGMII_0_000_NS             0
+#define YT8531_RC1R_RGMII_0_150_NS             1
+#define YT8531_RC1R_RGMII_0_300_NS             2
+#define YT8531_RC1R_RGMII_0_450_NS             3
+#define YT8531_RC1R_RGMII_0_600_NS             4
+#define YT8531_RC1R_RGMII_0_750_NS             5
+#define YT8531_RC1R_RGMII_0_900_NS             6
+#define YT8531_RC1R_RGMII_1_050_NS             7
+#define YT8531_RC1R_RGMII_1_200_NS             8
+#define YT8531_RC1R_RGMII_1_350_NS             9
+#define YT8531_RC1R_RGMII_1_500_NS             10
+#define YT8531_RC1R_RGMII_1_650_NS             11
+#define YT8531_RC1R_RGMII_1_800_NS             12
+#define YT8531_RC1R_RGMII_1_950_NS             13
+#define YT8531_RC1R_RGMII_2_100_NS             14
+#define YT8531_RC1R_RGMII_2_250_NS             15
+
+/* Phy gmii clock gating Register */
+#define YT8531_CLOCK_GATING_REG                0xC
+#define YT8531_CGR_RX_CLK_EN                   BIT(12)
+
+/* Specific Status Register */
+#define YTPHY_SPECIFIC_STATUS_REG              0x11
+#define YTPHY_DUPLEX_MASK                      BIT(13)
+#define YTPHY_DUPLEX_SHIFT                     13
+#define YTPHY_SPEED_MODE_MASK                  GENMASK(15, 14)
+#define YTPHY_SPEED_MODE_SHIFT                 14
+
+#define YT8531_EXTREG_SLEEP_CONTROL1_REG       0x27
+#define YT8531_ESC1R_SLEEP_SW                  BIT(15)
+#define YT8531_ESC1R_PLLON_SLP                 BIT(14)
+
+#define YT8531_RGMII_CONFIG1_REG               0xA003
+
+#define YT8531_CHIP_CONFIG_REG                 0xA001
+#define YT8531_CCR_SW_RST                      BIT(15)
+/* 1b0 disable 1.9ns rxc clock delay  *default*
+ * 1b1 enable 1.9ns rxc clock delay
+ */
+#define YT8531_CCR_RXC_DLY_EN                  BIT(8)
+#define YT8531_CCR_RXC_DLY_1_900_NS            1900
+
+/* bits in struct ytphy_plat_priv->flag */
+#define TX_CLK_ADJ_ENABLED                     BIT(0)
+#define AUTO_SLEEP_DISABLED                    BIT(1)
+#define KEEP_PLL_ENABLED                       BIT(2)
+#define TX_CLK_10_INVERTED                     BIT(3)
+#define TX_CLK_100_INVERTED                    BIT(4)
+#define TX_CLK_1000_INVERTED                   BIT(5)
+
+struct ytphy_plat_priv {
+       u32 rx_delay_ps;
+       u32 tx_delay_ps;
+       u32 clk_out_frequency;
+       u32 flag;
+};
+
+/**
+ * struct ytphy_cfg_reg_map - map a config value to a register value
+ * @cfg: value in device configuration
+ * @reg: value in the register
+ */
+struct ytphy_cfg_reg_map {
+       u32 cfg;
+       u32 reg;
+};
+
+static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = {
+       /* for tx delay / rx delay with YT8531_CCR_RXC_DLY_EN is not set. */
+       { 0,    YT8531_RC1R_RGMII_0_000_NS },
+       { 150,  YT8531_RC1R_RGMII_0_150_NS },
+       { 300,  YT8531_RC1R_RGMII_0_300_NS },
+       { 450,  YT8531_RC1R_RGMII_0_450_NS },
+       { 600,  YT8531_RC1R_RGMII_0_600_NS },
+       { 750,  YT8531_RC1R_RGMII_0_750_NS },
+       { 900,  YT8531_RC1R_RGMII_0_900_NS },
+       { 1050, YT8531_RC1R_RGMII_1_050_NS },
+       { 1200, YT8531_RC1R_RGMII_1_200_NS },
+       { 1350, YT8531_RC1R_RGMII_1_350_NS },
+       { 1500, YT8531_RC1R_RGMII_1_500_NS },
+       { 1650, YT8531_RC1R_RGMII_1_650_NS },
+       { 1800, YT8531_RC1R_RGMII_1_800_NS },
+       { 1950, YT8531_RC1R_RGMII_1_950_NS },   /* default tx/rx delay */
+       { 2100, YT8531_RC1R_RGMII_2_100_NS },
+       { 2250, YT8531_RC1R_RGMII_2_250_NS },
+
+       /* only for rx delay with YT8531_CCR_RXC_DLY_EN is set. */
+       { 0    + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_000_NS },
+       { 150  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_150_NS },
+       { 300  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_300_NS },
+       { 450  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_450_NS },
+       { 600  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_600_NS },
+       { 750  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_750_NS },
+       { 900  + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_0_900_NS },
+       { 1050 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_050_NS },
+       { 1200 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_200_NS },
+       { 1350 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_350_NS },
+       { 1500 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_500_NS },
+       { 1650 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_650_NS },
+       { 1800 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_800_NS },
+       { 1950 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_1_950_NS },
+       { 2100 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_2_100_NS },
+       { 2250 + YT8531_CCR_RXC_DLY_1_900_NS,   YT8531_RC1R_RGMII_2_250_NS }
+};
+
+static u32 ytphy_get_delay_reg_value(struct phy_device *phydev,
+                                    u32 val,
+                                    u16 *rxc_dly_en)
+{
+       int tb_size = ARRAY_SIZE(ytphy_rgmii_delays);
+       int tb_size_half = tb_size / 2;
+       int i;
+
+       /* when rxc_dly_en is NULL, it is get the delay for tx, only half of
+        * tb_size is valid.
+        */
+       if (!rxc_dly_en)
+               tb_size = tb_size_half;
+
+       for (i = 0; i < tb_size; i++) {
+               if (ytphy_rgmii_delays[i].cfg == val) {
+                       if (rxc_dly_en && i < tb_size_half)
+                               *rxc_dly_en = 0;
+                       return ytphy_rgmii_delays[i].reg;
+               }
+       }
+
+       pr_warn("Unsupported value %d, using default (%u)\n",
+               val, YT8531_RC1R_RGMII_1_950_NS);
+
+       /* when rxc_dly_en is not NULL, it is get the delay for rx.
+        * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps,
+        * so YT8531_CCR_RXC_DLY_EN should not be set.
+        */
+       if (rxc_dly_en)
+               *rxc_dly_en = 0;
+
+       return YT8531_RC1R_RGMII_1_950_NS;
+}
+
+static int ytphy_modify_ext(struct phy_device *phydev, u16 regnum, u16 mask,
+                           u16 set)
+{
+       int ret;
+
+       ret = phy_write(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_SELECT, regnum);
+       if (ret < 0)
+               return ret;
+
+       return phy_modify(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_DATA, mask, set);
+}
+
+static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev)
+{
+       struct ytphy_plat_priv  *priv = phydev->priv;
+       u16 rxc_dly_en = YT8531_CCR_RXC_DLY_EN;
+       u32 rx_reg, tx_reg;
+       u16 mask, val = 0;
+       int ret;
+
+       rx_reg = ytphy_get_delay_reg_value(phydev, priv->rx_delay_ps,
+                                          &rxc_dly_en);
+       tx_reg = ytphy_get_delay_reg_value(phydev, priv->tx_delay_ps,
+                                          NULL);
+
+       switch (phydev->interface) {
+       case PHY_INTERFACE_MODE_RGMII:
+               rxc_dly_en = 0;
+               break;
+       case PHY_INTERFACE_MODE_RGMII_RXID:
+               val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg);
+               break;
+       case PHY_INTERFACE_MODE_RGMII_TXID:
+               rxc_dly_en = 0;
+               val |= FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+               break;
+       case PHY_INTERFACE_MODE_RGMII_ID:
+               val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg) |
+                      FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+               break;
+       default: /* do not support other modes */
+               return -EOPNOTSUPP;
+       }
+
+       ret = ytphy_modify_ext(phydev, YT8531_CHIP_CONFIG_REG,
+                              YT8531_CCR_RXC_DLY_EN, rxc_dly_en);
+       if (ret < 0)
+               return ret;
+
+       /* Generally, it is not necessary to adjust YT8531_RC1R_FE_TX_DELAY */
+       mask = YT8531_RC1R_RX_DELAY_MASK | YT8531_RC1R_GE_TX_DELAY_MASK;
+       return ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG, mask, val);
+}
+
+static int yt8531_parse_status(struct phy_device *phydev)
+{
+       int val;
+       int speed, speed_mode;
+
+       val = phy_read(phydev, MDIO_DEVAD_NONE, YTPHY_SPECIFIC_STATUS_REG);
+       if (val < 0)
+               return val;
+
+       speed_mode = (val & YTPHY_SPEED_MODE_MASK) >> YTPHY_SPEED_MODE_SHIFT;
+       switch (speed_mode) {
+       case 2:
+               speed = SPEED_1000;
+               break;
+       case 1:
+               speed = SPEED_100;
+               break;
+       default:
+               speed = SPEED_10;
+               break;
+       }
+
+       phydev->speed = speed;
+       phydev->duplex = (val & YTPHY_DUPLEX_MASK) >> YTPHY_DUPLEX_SHIFT;
+
+       return 0;
+}
+
+static int yt8531_startup(struct phy_device *phydev)
+{
+       struct ytphy_plat_priv  *priv = phydev->priv;
+       u16 val = 0;
+       int ret;
+
+       ret = genphy_update_link(phydev);
+       if (ret)
+               return ret;
+
+       ret = yt8531_parse_status(phydev);
+       if (ret)
+               return ret;
+
+       if (phydev->speed < 0)
+               return -EINVAL;
+
+       if (!(priv->flag & TX_CLK_ADJ_ENABLED))
+               return 0;
+
+       switch (phydev->speed) {
+       case SPEED_1000:
+               if (priv->flag & TX_CLK_1000_INVERTED)
+                       val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+               break;
+       case SPEED_100:
+               if (priv->flag & TX_CLK_100_INVERTED)
+                       val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+               break;
+       case SPEED_10:
+               if (priv->flag & TX_CLK_10_INVERTED)
+                       val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+               break;
+       default:
+               printf("UNKNOWN SPEED\n");
+               return -EINVAL;
+       }
+
+       ret = ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG,
+                              YT8531_RC1R_TX_CLK_SEL_INVERTED, val);
+       if (ret < 0)
+               pr_warn("Modify TX_CLK_SEL err:%d\n", ret);
+
+       return 0;
+}
+
+static void ytphy_dt_parse(struct phy_device *phydev)
+{
+       struct ytphy_plat_priv  *priv = phydev->priv;
+       int ret;
+
+       ret = ofnode_read_u32(phydev->node, "motorcomm,clk-out-frequency-hz",
+                             &priv->clk_out_frequency);
+       if (ret < 0)
+               priv->clk_out_frequency = YTPHY_DTS_OUTPUT_CLK_DIS;
+
+       ret = ofnode_read_u32(phydev->node, "rx-internal-delay-ps",
+                             &priv->rx_delay_ps);
+       if (ret < 0)
+               priv->rx_delay_ps = YT8531_RC1R_RGMII_1_950_NS;
+
+       ret = ofnode_read_u32(phydev->node, "tx-internal-delay-ps",
+                             &priv->tx_delay_ps);
+       if (ret < 0)
+               priv->tx_delay_ps = YT8531_RC1R_RGMII_1_950_NS;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,auto-sleep-disabled"))
+               priv->flag |= AUTO_SLEEP_DISABLED;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,keep-pll-enabled"))
+               priv->flag |= KEEP_PLL_ENABLED;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-adj-enabled"))
+               priv->flag |= TX_CLK_ADJ_ENABLED;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-10-inverted"))
+               priv->flag |= TX_CLK_10_INVERTED;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-100-inverted"))
+               priv->flag |= TX_CLK_100_INVERTED;
+
+       if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-1000-inverted"))
+               priv->flag |= TX_CLK_1000_INVERTED;
+}
+
+static int yt8531_config(struct phy_device *phydev)
+{
+       struct ytphy_plat_priv  *priv = phydev->priv;
+       u16 mask, val;
+       int ret;
+
+       ret = genphy_config_aneg(phydev);
+       if (ret < 0)
+               return ret;
+
+       ytphy_dt_parse(phydev);
+       switch (priv->clk_out_frequency) {
+       case YTPHY_DTS_OUTPUT_CLK_DIS:
+               mask = YT8531_SCR_SYNCE_ENABLE;
+               val = 0;
+               break;
+       case YTPHY_DTS_OUTPUT_CLK_25M:
+               mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+                          YT8531_SCR_CLK_FRE_SEL_125M;
+               val = YT8531_SCR_SYNCE_ENABLE |
+                         FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+                                    YT8531_SCR_CLK_SRC_REF_25M);
+               break;
+       case YTPHY_DTS_OUTPUT_CLK_125M:
+               mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+                          YT8531_SCR_CLK_FRE_SEL_125M;
+               val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M |
+                         FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+                                    YT8531_SCR_CLK_SRC_PLL_125M);
+               break;
+       default:
+               pr_warn("Freq err:%u\n", priv->clk_out_frequency);
+               return -EINVAL;
+       }
+
+       ret = ytphy_modify_ext(phydev, YTPHY_SYNCE_CFG_REG, mask,
+                              val);
+       if (ret < 0)
+               return ret;
+
+       ret = ytphy_rgmii_clk_delay_config(phydev);
+       if (ret < 0)
+               return ret;
+
+       if (priv->flag & AUTO_SLEEP_DISABLED) {
+               /* disable auto sleep */
+               ret = ytphy_modify_ext(phydev,
+                                      YT8531_EXTREG_SLEEP_CONTROL1_REG,
+                                      YT8531_ESC1R_SLEEP_SW, 0);
+               if (ret < 0)
+                       return ret;
+       }
+
+       if (priv->flag & KEEP_PLL_ENABLED) {
+               /* enable RXC clock when no wire plug */
+               ret = ytphy_modify_ext(phydev,
+                                      YT8531_CLOCK_GATING_REG,
+                                      YT8531_CGR_RX_CLK_EN, 0);
+               if (ret < 0)
+                       return ret;
+       }
+
+       return 0;
+}
+
+static int yt8531_probe(struct phy_device *phydev)
+{
+       struct ytphy_plat_priv  *priv;
+
+       priv = calloc(1, sizeof(struct ytphy_plat_priv));
+       if (!priv)
+               return -ENOMEM;
+
+       phydev->priv = priv;
+
+       return 0;
+}
+
+static struct phy_driver motorcomm8531_driver = {
+       .name          = "YT8531 Gigabit Ethernet",
+       .uid           = PHY_ID_YT8531,
+       .mask          = PHY_ID_MASK,
+       .features      = PHY_GBIT_FEATURES,
+       .probe         = &yt8531_probe,
+       .config        = &yt8531_config,
+       .startup       = &yt8531_startup,
+       .shutdown      = &genphy_shutdown,
+};
+
+int phy_motorcomm_init(void)
+{
+       phy_register(&motorcomm8531_driver);
+
+       return 0;
+}
drivers/net/phy/phy.c +3 -1
index 80230b907c..78bde61798 100644
@@ -570,6 +570,9 @@ int phy_init(void)
 #endif
 #ifdef CONFIG_PHY_XILINX_GMII2RGMII
        phy_xilinx_gmii2rgmii_init();
+#endif
+#ifdef CONFIG_PHY_MOTORCOMM
+       phy_motorcomm_init();
 #endif
        genphy_init();
 
@@ -755,7 +758,6 @@ static struct phy_device *create_phy_by_mask(struct mii_dev *bus,
        while (phy_mask) {
                int addr = ffs(phy_mask) - 1;
                int r = get_phy_id(bus, addr, devad, &phy_id);
-
                /*
                 * If the PHY ID is flat 0 we ignore it.  There are C45 PHYs
                 * that return all 0s for C22 reads (like Aquantia AQR112) and
include/phy.h +1 -1
index 87aa86c2e7..f7bb2fe0af 100644
@@ -344,6 +344,7 @@ int phy_mscc_init(void);
 int phy_fixed_init(void);
 int phy_ncsi_init(void);
 int phy_xilinx_gmii2rgmii_init(void);
+int phy_motorcomm_init(void);
 
 int board_phy_config(struct phy_device *phydev);
 int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id);
--
Quoted 2 lines

2.17.1

#3 lore raw

PATCH v2 2/5 net: dwc_eth_qos: Add StarFive ethernet driver glue layer

In reply to Yanhong Wang

The StarFive ETHQOS hardware has its own clock and reset,so add a corresponding glue driver to configure them.

---
 drivers/net/Kconfig                |   7 +
 drivers/net/Makefile               |   1 +
 drivers/net/dwc_eth_qos.c          |   6 +
 drivers/net/dwc_eth_qos.h          |   1 +
 drivers/net/dwc_eth_qos_starfive.c | 249 +++++++++++++++++++++++++++++
 5 files changed, 264 insertions(+)
 create mode 100644 drivers/net/dwc_eth_qos_starfive.c
drivers/net/Kconfig +7 -0
index ceadee98a1..161289d00f 100644
@@ -249,6 +249,13 @@ config DWC_ETH_QOS_QCOM
 	  The Synopsys Designware Ethernet QOS IP block with specific
 	  configuration used in Qcom QCS404 SoC.
 
+config DWC_ETH_QOS_STARFIVE
+	bool "Synopsys DWC Ethernet QOS device support for STARFIVE"
+	depends on DWC_ETH_QOS
+	help
+	  The Synopsys Designware Ethernet QOS IP block with specific
+	  configuration used in STARFIVE  JH7110 soc.
+
 config E1000
 	bool "Intel PRO/1000 Gigabit Ethernet support"
 	depends on PCI
drivers/net/Makefile +1 -0
index 75daa5e694..69af678757 100644
@@ -21,6 +21,7 @@ obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
 obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
 obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
 obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
+obj-$(CONFIG_DWC_ETH_QOS_STARFIVE) += dwc_eth_qos_starfive.o
 obj-$(CONFIG_E1000) += e1000.o
 obj-$(CONFIG_E1000_SPI) += e1000_spi.o
 obj-$(CONFIG_EEPRO100) += eepro100.o
drivers/net/dwc_eth_qos.c +6 -0
index 112deb546d..9aecd56e73 100644
@@ -1718,6 +1718,12 @@ static const struct udevice_id eqos_ids[] = {
 		.data = (ulong)&eqos_qcom_config
 	},
 #endif
+#if IS_ENABLED(CONFIG_DWC_ETH_QOS_STARFIVE)
+	{
+		.compatible = "starfive,jh7110-dwmac",
+		.data = (ulong)&eqos_jh7110_config
+	},
+#endif
 
 	{ }
 };
drivers/net/dwc_eth_qos.h +1 -0
index fddbe9336c..a6b719af80 100644
@@ -289,3 +289,4 @@ int eqos_null_ops(struct udevice *dev);
 
 extern struct eqos_config eqos_imx_config;
 extern struct eqos_config eqos_qcom_config;
+extern struct eqos_config eqos_jh7110_config;
drivers/net/dwc_eth_qos_starfive.c new file +249 -0

249 lines not on this page · raw message

Signature · 1 line
2.17.1
#4 lore raw

Re: [PATCH v2 2/5] net: dwc_eth_qos: Add StarFive ethernet driver glue layer

Hi Yanhong,

Quoted 14 lines · Yanhong Wang

The StarFive ETHQOS hardware has its own clock and reset,so add a corresponding glue driver to configure them.

---
 drivers/net/Kconfig                |   7 +
 drivers/net/Makefile               |   1 +
 drivers/net/dwc_eth_qos.c          |   6 +
 drivers/net/dwc_eth_qos.h          |   1 +
 drivers/net/dwc_eth_qos_starfive.c | 249 +++++++++++++++++++++++++++++
 5 files changed, 264 insertions(+)
 create mode 100644 drivers/net/dwc_eth_qos_starfive.c

[..]

Quoted 7 lines
drivers/net/dwc_eth_qos_starfive.c new file +7 -0
+static struct eqos_ops eqos_jh7110_ops = {
+       .eqos_inval_desc = eqos_inval_desc_generic,
+       .eqos_flush_desc = eqos_flush_desc_generic,
+       .eqos_inval_buffer = eqos_inval_buffer_generic,
+       .eqos_flush_buffer = eqos_flush_buffer_generic,
+       .eqos_probe_resources = eqos_probe_resources_jh7110,
+       .eqos_remove_resources = eqos_remove_resources_jh7110,

drivers/net/dwc_eth_qos_starfive.c line 231

Quoted 10 lines
drivers/net/dwc_eth_qos_starfive.c new file +10 -0
+       .eqos_stop_resets = eqos_stop_resets_jh7110,
+       .eqos_start_resets = eqos_start_resets_jh7110,
+       .eqos_stop_clks = eqos_stop_clks_jh7110,
+       .eqos_start_clks = eqos_start_clks_jh7110,
+       .eqos_calibrate_pads = eqos_null_ops,
+       .eqos_disable_calibration = eqos_null_ops,
+       .eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_jh7110,
+       .eqos_get_enetaddr = eqos_null_ops,
+       .eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_jh7110
+};

What is eqos_ops? Why is this layer needed in U-Boot?

Can you not use driver model directly?

Regards,
Simon

#5 lore raw

Re: [PATCH v2 2/5] net: dwc_eth_qos: Add StarFive ethernet driver glue layer

Quoted 32 lines · Simon Glass

Hi Yanhong,

Quoted 14 lines · Yanhong Wang

The StarFive ETHQOS hardware has its own clock and reset,so add a corresponding glue driver to configure them.

---
 drivers/net/Kconfig                |   7 +
 drivers/net/Makefile               |   1 +
 drivers/net/dwc_eth_qos.c          |   6 +
 drivers/net/dwc_eth_qos.h          |   1 +
 drivers/net/dwc_eth_qos_starfive.c | 249 +++++++++++++++++++++++++++++
 5 files changed, 264 insertions(+)
 create mode 100644 drivers/net/dwc_eth_qos_starfive.c

[..]

Quoted 11 lines
drivers/net/dwc_eth_qos_starfive.c new file +11 -0
+static struct eqos_ops eqos_jh7110_ops = {
+       .eqos_inval_desc = eqos_inval_desc_generic,
+       .eqos_flush_desc = eqos_flush_desc_generic,
+       .eqos_inval_buffer = eqos_inval_buffer_generic,
+       .eqos_flush_buffer = eqos_flush_buffer_generic,
+       .eqos_probe_resources = eqos_probe_resources_jh7110,
+       .eqos_remove_resources = eqos_remove_resources_jh7110,
+       .eqos_stop_resets = eqos_stop_resets_jh7110,
+       .eqos_start_resets = eqos_start_resets_jh7110,
+       .eqos_stop_clks = eqos_stop_clks_jh7110,
+       .eqos_start_clks = eqos_start_clks_jh7110,
Quoted 9 lines

drivers/net/dwc_eth_qos_starfive.c line 231

Quoted 6 lines
drivers/net/dwc_eth_qos_starfive.c new file +6 -0
+       .eqos_calibrate_pads = eqos_null_ops,
+       .eqos_disable_calibration = eqos_null_ops,
+       .eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_jh7110,
+       .eqos_get_enetaddr = eqos_null_ops,
+       .eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_jh7110
+};

What is eqos_ops? Why is this layer needed in U-Boot?

The JH7110 uses the Synopsys Designware Ethernet QOS (Quality Of Service) IP block, the driver implementation uses 'dwc_eth_qos.c,' but there are some differences in clock and reset, so there is a corresponding glue layer. This glue layer references the implementation of 'dwc_eth_qos_imx.c' and 'dwc_eth_qos_qcom.c'.

Quoted 2 lines

Can you not use driver model directly?
If you use the driver model directly, many of the implementations are the same

as "dwc_eth_qos.c", so to avoid duplicate implementations, just add the glue layer.

Quoted 2 lines

Regards,
Simon

#6 lore raw

PATCH v2 3/5 riscv: dts: jh7110: Add ethernet device tree nodes

In reply to Yanhong Wang

Add ethernet device tree node to support StarFive ethernet driver for the JH7110 RISC-V SoC.

---
 arch/riscv/dts/jh7110.dtsi | 69 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 69 insertions(+)
arch/riscv/dts/jh7110.dtsi +69 -0
index bd60879615..58e332e9d7 100644
@@ -235,6 +235,13 @@
 		#clock-cells = <0>;
 	};
 
+	stmmac_axi_setup: stmmac-axi-config {
+		snps,lpi_en;
+		snps,wr_osr_lmt = <4>;
+		snps,rd_osr_lmt = <4>;
+		snps,blen = <256 128 64 32 0 0 0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&plic>;
@@ -539,6 +546,68 @@
 			status = "disabled";
 		};
 
+		gmac0: ethernet@16030000 {
+			compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
+			reg = <0x0 0x16030000 0x0 0x10000>;
+			clocks = <&aoncrg JH7110_AONCLK_GMAC0_AXI>,
+				 <&aoncrg JH7110_AONCLK_GMAC0_AHB>,
+				 <&syscrg JH7110_SYSCLK_GMAC0_PTP>,
+				 <&aoncrg JH7110_AONCLK_GMAC0_TX_INV>,
+				 <&syscrg JH7110_SYSCLK_GMAC0_GTXC>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref",
+				      "tx", "gtx";
+			resets = <&aoncrg JH7110_AONRST_GMAC0_AXI>,
+				 <&aoncrg JH7110_AONRST_GMAC0_AHB>;
+			reset-names = "stmmaceth", "ahb";
+			interrupts = <7>, <6>, <5>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			snps,multicast-filter-bins = <64>;
+			snps,perfect-filter-entries = <8>;
+			rx-fifo-depth = <2048>;
+			tx-fifo-depth = <2048>;
+			snps,fixed-burst;
+			snps,no-pbl-x8;
+			snps,force_thresh_dma_mode;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,tso;
+			snps,en-tx-lpi-clockgating;
+			snps,txpbl = <16>;
+			snps,rxpbl = <16>;
+			starfive,syscon = <&aon_syscon 0xc 0x12>;
+			status = "disabled";
+		};
+
+		gmac1: ethernet@16040000 {
+			compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
+			reg = <0x0 0x16040000 0x0 0x10000>;
+			clocks = <&syscrg JH7110_SYSCLK_GMAC1_AXI>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_AHB>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_PTP>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_TX_INV>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_GTXC>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref",
+				      "tx", "gtx";
+			resets = <&syscrg JH7110_SYSRST_GMAC1_AXI>,
+				 <&syscrg JH7110_SYSRST_GMAC1_AHB>;
+			reset-names = "stmmaceth", "ahb";
+			interrupts = <78>, <77>, <76>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			snps,multicast-filter-bins = <64>;
+			snps,perfect-filter-entries = <8>;
+			rx-fifo-depth = <2048>;
+			tx-fifo-depth = <2048>;
+			snps,fixed-burst;
+			snps,no-pbl-x8;
+			snps,force_thresh_dma_mode;
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,tso;
+			snps,en-tx-lpi-clockgating;
+			snps,txpbl = <16>;
+			snps,rxpbl = <16>;
+			starfive,syscon = <&sys_syscon 0x90 0x2>;
+			status = "disabled";
+		};
+
 		aoncrg: clock-controller@17000000 {
 			compatible = "starfive,jh7110-aoncrg";
 			reg = <0x0 0x17000000 0x0 0x10000>;
Signature · 1 line
2.17.1
#7 lore raw

PATCH v2 4/5 riscv: dts: starfive: Add phy clock delay configuration for StarFive VisionFive2 board

In reply to Yanhong Wang

The StarFive VisionFive2 board include 1.2A and 1.3B version.

v1.3B uses motorcomm YT8531(rgmii-id phy) x2, phy clock need delay and inverse configurations.

v1.2A gmac0 uses motorcomm YT8531(rgmii-id) PHY, and needs phy clock delay configurations.

v1.2A gmac1 uses motorcomm YT8512(rmii) PHY, and needs to switch rx and tx to external clock sources.

---
 .../jh7110-starfive-visionfive-2-v1.2a.dts    | 13 +++++++
 .../jh7110-starfive-visionfive-2-v1.3b.dts    | 27 +++++++++++++++
 .../dts/jh7110-starfive-visionfive-2.dtsi     | 34 +++++++++++++++++++
 3 files changed, 74 insertions(+)
arch/riscv/dts/jh7110-starfive-visionfive-2-v1.2a.dts +13 -0
index b9d26d7af7..918e77220a 100644
@@ -10,3 +10,16 @@
 	model = "StarFive VisionFive 2 v1.2A";
 	compatible = "starfive,visionfive-2-v1.2a", "starfive,jh7110";
 };
+
+&gmac1 {
+	phy-mode = "rmii";
+	assigned-clocks = <&syscrg JH7110_SYSCLK_GMAC1_TX>,
+			  <&syscrg JH7110_SYSCLK_GMAC1_RX>;
+	assigned-clock-parents = <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>;
+};
+
+&phy0 {
+	rx-internal-delay-ps = <1900>;
+	tx-internal-delay-ps = <1350>;
+};
arch/riscv/dts/jh7110-starfive-visionfive-2-v1.3b.dts +27 -0
index 3b3b3453a1..0fcd6ab80f 100644
@@ -10,3 +10,30 @@
 	model = "StarFive VisionFive 2 v1.3B";
 	compatible = "starfive,visionfive-2-v1.3b", "starfive,jh7110";
 };
+
+&gmac0 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+};
+
+&gmac1 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_GMAC1_TX>;
+	assigned-clock-parents = <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>;
+};
+
+&phy0 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+	rx-internal-delay-ps = <1900>;
+	tx-internal-delay-ps = <1500>;
+};
+
+&phy1 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-100-inverted;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+};
arch/riscv/dts/jh7110-starfive-visionfive-2.dtsi +34 -0
index c6b6dfa940..3c1148ae2d 100644
@@ -17,6 +17,8 @@
 		i2c2 = &i2c2;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 	};
 
 	chosen {
@@ -317,3 +319,35 @@
 	assigned-clock-parents = <&osc>;
 	assigned-clock-rates = <0>;
 };
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy1: ethernet-phy@1 {
+			reg = <0>;
+		};
+	};
+};
Signature · 1 line
2.17.1
#8 lore raw

PATCH v2 5/5 configs: starfive: Enable ethernet configuration for StarFive VisionFive 2

In reply to Yanhong Wang

Enable DWC_ETH_QOS and PHY_MOTORCOMM configuration to support ethernet function for StarFive VisionFive 2 board,including versions 1.2A and 1.3B.

---
 configs/starfive_visionfive2_12a_defconfig | 12 +++++++++++-
 configs/starfive_visionfive2_13b_defconfig | 12 +++++++++++-
 2 files changed, 22 insertions(+), 2 deletions(-)
configs/starfive_visionfive2_12a_defconfig +11 -1
index e0f98292ff..1340701c69 100644
@@ -21,8 +21,8 @@ CONFIG_SPL_OPENSBI_LOAD_ADDR=0x40000000
 CONFIG_ARCH_RV64I=y
 CONFIG_CMODEL_MEDANY=y
 CONFIG_RISCV_SMODE=y
-CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT=y
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_QSPI_BOOT=y
 CONFIG_SD_BOOT=y
 CONFIG_USE_BOOTARGS=y
@@ -52,6 +52,9 @@ CONFIG_SYS_BOOTM_LEN=0x4000000
 CONFIG_CMD_MEMINFO=y
 CONFIG_CMD_TFTPPUT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
 CONFIG_SPL_CLK_COMPOSITE_CCF=y
 CONFIG_CLK_COMPOSITE_CCF=y
 CONFIG_SPL_CLK_JH7110=y
@@ -65,6 +68,13 @@ CONFIG_SPI_FLASH_EON=y
 CONFIG_SPI_FLASH_GIGADEVICE=y
 CONFIG_SPI_FLASH_ISSI=y
 CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_PHY_MOTORCOMM=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_ETH_PHY=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_STARFIVE=y
+CONFIG_RGMII=y
+CONFIG_RMII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCONF=y
 CONFIG_SPL_PINCTRL=y
configs/starfive_visionfive2_13b_defconfig +11 -1
index 550d0ff3ab..a6415a6cde 100644
@@ -21,8 +21,8 @@ CONFIG_SPL_OPENSBI_LOAD_ADDR=0x40000000
 CONFIG_ARCH_RV64I=y
 CONFIG_CMODEL_MEDANY=y
 CONFIG_RISCV_SMODE=y
-CONFIG_DISTRO_DEFAULTS=y
 CONFIG_FIT=y
+CONFIG_DISTRO_DEFAULTS=y
 CONFIG_QSPI_BOOT=y
 CONFIG_SD_BOOT=y
 CONFIG_USE_BOOTARGS=y
@@ -52,6 +52,9 @@ CONFIG_SYS_BOOTM_LEN=0x4000000
 CONFIG_CMD_MEMINFO=y
 CONFIG_CMD_TFTPPUT=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
 CONFIG_SPL_CLK_COMPOSITE_CCF=y
 CONFIG_CLK_COMPOSITE_CCF=y
 CONFIG_SPL_CLK_JH7110=y
@@ -65,6 +68,13 @@ CONFIG_SPI_FLASH_EON=y
 CONFIG_SPI_FLASH_GIGADEVICE=y
 CONFIG_SPI_FLASH_ISSI=y
 CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_PHY_MOTORCOMM=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_ETH_PHY=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_STARFIVE=y
+CONFIG_RGMII=y
+CONFIG_RMII=y
 CONFIG_PINCTRL=y
 CONFIG_PINCONF=y
 CONFIG_SPL_PINCTRL=y
Signature · 1 line
2.17.1