arm: add support for Hisilicon HiSTB family SoCs
Subsystems (5)
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH 1/4 arm: add support for Hisilicon HiSTB family SoCs
First supported chip is hi3798mv200 (which is similar to Hi3798cv200 used by poplar).
--- MAINTAINERS | 1 + arch/arm/Kconfig | 12 ++++++++++++ arch/arm/Makefile | 1 + arch/arm/mach-histb/Kconfig | 14 ++++++++++++++ arch/arm/mach-histb/Makefile | 4 ++++ arch/arm/mach-histb/board_common.c | 31 ++++++++++++++++++++++++++++++ arch/arm/mach-histb/sysmap-histb.c | 31 ++++++++++++++++++++++++++++++ 7 files changed, 94 insertions(+) create mode 100644 arch/arm/mach-histb/Kconfig create mode 100644 arch/arm/mach-histb/Makefile create mode 100644 arch/arm/mach-histb/board_common.c create mode 100644 arch/arm/mach-histb/sysmap-histb.c
MAINTAINERS +1 -0
@@ -291,6 +291,7 @@ S: Maintained F: arch/arm/cpu/armv8/hisilicon F: arch/arm/include/asm/arch-hi6220/ F: arch/arm/include/asm/arch-hi3660/ +F: arch/arm/mach-histb ARM HPE GXP ARCHITECTURE M: Jean-Marie Verdun <[email protected]>
arch/arm/Kconfig +12 -0
@@ -578,6 +578,16 @@ config ARCH_DAVINCI help Support for TI's DaVinci platform. +config ARCH_HISTB + bool "Hisilicon HiSTB SoCs" + select DM + select DM_SERIAL + select OF_CONTROL + select PL01X_SERIAL + imply CMD_DM + help + Support for HiSTB SoCs. + config ARCH_KIRKWOOD bool "Marvell Kirkwood" select ARCH_MISC_INIT
@@ -2156,6 +2166,8 @@ source "arch/arm/mach-hpe/gxp/Kconfig" source "arch/arm/mach-highbank/Kconfig" +source "arch/arm/mach-histb/Kconfig" + source "arch/arm/mach-integrator/Kconfig" source "arch/arm/mach-ipq40xx/Kconfig"
arch/arm/Makefile +1 -0
@@ -61,6 +61,7 @@ machine-$(CONFIG_ARCH_DAVINCI) += davinci machine-$(CONFIG_ARCH_EXYNOS) += exynos machine-$(CONFIG_ARCH_GXP) += hpe machine-$(CONFIG_ARCH_HIGHBANK) += highbank +machine-$(CONFIG_ARCH_HISTB) += histb machine-$(CONFIG_ARCH_IPQ40XX) += ipq40xx machine-$(CONFIG_ARCH_K3) += k3 machine-$(CONFIG_ARCH_KEYSTONE) += keystone
arch/arm/mach-histb/Kconfig new file +14 -0
@@ -0,0 +1,14 @@ +if ARCH_HISTB + +choice + prompt "Select a HiSTB SoC" + +config ARCH_HI3798MV2X + bool "Hi3798M V2XX series SoC" + select ARM64 + help + Support for Hi3798MV2XX series SoCs. + +endchoice + +endif
arch/arm/mach-histb/Makefile new file +4 -0
@@ -0,0 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += sysmap-histb.o +obj-y += board_common.o
arch/arm/mach-histb/board_common.c new file +31 -0
@@ -0,0 +1,31 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Board init file for all histb boards +* +* (C) Copyright 2023 Yang Xiwen <[email protected]> +*/ + +#include <common.h> +#include <fdtdec.h> +#include <init.h> +#include <asm/system.h> + +int __weak board_init (void ) +{ +return 0 ; +} + +int __weak dram_init_banksize (void ) +{ +return fdtdec_setup_memory_banksize (); +} + +int __weak dram_init (void ) +{ +return fdtdec_setup_mem_size_base (); +} + +void __weak reset_cpu (void ) +{ +psci_system_reset (); +}
arch/arm/mach-histb/sysmap-histb.c new file +31 -0
@@ -0,0 +1,31 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Hisilicon HiSTB memory map +* +* (C) Copyright 2023 Yang Xiwen <[email protected]> +*/ + +#include <common.h> +#include <asm/armv8/mmu.h> + +static struct mm_region histb_mem_map[] = { + { + .virt =0x0UL ,/* DRAM */ + .phys =0x0UL , + .size =0x80000000UL , + .attrs =PTE_BLOCK_MEMTYPE (MT_NORMAL ) | +PTE_BLOCK_INNER_SHARE + }, { + .virt =0x80000000UL ,/* Peripheral block */ + .phys =0x80000000UL , + .size =0x80000000UL , + .attrs =PTE_BLOCK_MEMTYPE (MT_DEVICE_NGNRNE ) | +PTE_BLOCK_NON_SHARE | +PTE_BLOCK_PXN |PTE_BLOCK_UXN + }, { +/* Terminator */ +0 , + } +}; + +struct mm_region *mem_map = histb_mem_map;
Signature · 1 line
2.39.1
Quoted 4 lines · Yang Xiwen
First supported chip is hi3798mv200 (which is similar to Hi3798cv200 used by poplar).
Signed-off-by Yang Xiwen <[email protected]>
For the series, applied to u-boot/master, thanks!
Signature · 1 line
Tom
Quoted 9 lines · Tom Rini
Quoted 4 lines · Yang Xiwen
First supported chip is hi3798mv200 (which is similar to Hi3798cv200 used by poplar).
Signed-off-by Yang Xiwen <[email protected]>For the series, applied to u-boot/master, thanks!
Oops, I almost forgot this and had done a lot of updates since then. There are still many things to do and I will send them out when I think it is ready. Anyway, thanks for your reply, Tom. I guess next time I can request for you to pull instead of mailing a series of patches, right?
Signature · 2 lines
Best regards, Yang Xiwen
Quoted 6 lines · Yang Xiwen
Quoted 5 lines · Tom Rini
Quoted 3 lines · Yang Xiwen
First supported chip is hi3798mv200 (which is similar to Hi3798cv200 used by poplar).
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Yang Xiwen <[email protected]>For the series, applied to u-boot/master, thanks!
Oops, I almost forgot this and had done a lot of updates since then. There are still many things to do and I will send them out when I think it is ready. Anyway, thanks for your reply, Tom. I guess next time I can request for you to pull instead of mailing a series of patches, right?
A series of patches is still the best path forward, thanks.
Signature · 1 line
Tom
PATCH 2/4 mmc: hi6220_dw_mmc: add compatible for HC2910 support
In reply to a message not in the archiveIt adds compatible "hisilicon,hi3798mv200-dw-mshc" for HC2910 SoC Hi3798MV200 to probe this mmc driver.
--- drivers/mmc/hi6220_dw_mmc.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/mmc/hi6220_dw_mmc.c +2 -0
@@ -100,6 +100,8 @@ static const struct udevice_id hi6220_dwmmc_ids[] = { .data = (ulong)&hi6220_mmc_data }, { .compatible = "hisilicon,hi3798cv200-dw-mshc", .data = (ulong)&hi6220_mmc_data }, + { .compatible = "hisilicon,hi3798mv200-dw-mshc", + .data = (ulong)&hi6220_mmc_data }, { .compatible = "hisilicon,hi3660-dw-mshc", .data = (ulong)&hi3660_mmc_data }, { }
Signature · 1 line
2.39.1
Re: [PATCH 2/4] mmc: hi6220_dw_mmc: add compatible for HC2910 support
Quoted 2 lines · Yang Xiwen
It adds compatible "hisilicon,hi3798mv200-dw-mshc" for HC2910 SoC Hi3798MV200 to probe this mmc driver.
It would be better if you could write more information, about why it reuse the data structure of hi6220_mmc_data.
Regards,
Peng.
Quoted 19 lines
Signed-off-by Yang Xiwen <[email protected]>--- drivers/mmc/hi6220_dw_mmc.c | 2 ++ 1 file changed, 2 insertions(+)drivers/mmc/hi6220_dw_mmc.c +2
-0@@ -100,6 +100,8 @@ static const struct udevice_id hi6220_dwmmc_ids[] = { .data = (ulong)&hi6220_mmc_data }, { .compatible = "hisilicon,hi3798cv200-dw-mshc", .data = (ulong)&hi6220_mmc_data }, + { .compatible = "hisilicon,hi3798mv200-dw-mshc", + .data = (ulong)&hi6220_mmc_data }, { .compatible = "hisilicon,hi3660-dw-mshc", .data = (ulong)&hi3660_mmc_data }, { }
PATCH 3/4 dt-binding: histb-clock: add clocks definition for Hi3798MV200
In reply to a message not in the archiveThese clocks are found on Hi3798MV200
--- include/dt-bindings/clock/histb-clock.h | 12 ++++++++++++ 1 file changed, 12 insertions(+)
include/dt-bindings/clock/histb-clock.h +12 -0
@@ -70,6 +70,18 @@#define HISTB_USB3_UTMI_CLK1 48#define HISTB_USB3_PIPE_CLK1 49#define HISTB_USB3_SUSPEND_CLK1 50 +#define HISTB_SDIO1_BIU_CLK 51 +#define HISTB_SDIO1_CIU_CLK 52 +#define HISTB_SDIO1_DRV_CLK 53 +#define HISTB_SDIO1_SAMPLE_CLK 54 + +/* Hi3798MV200 specific clocks */ + +// reuse clocks of histb +#define HI3798MV200_GMAC_CLK HISTB_ETH0_MAC_CLK +#define HI3798MV200_GMACIF_CLK HISTB_ETH0_MACIF_CLK +#define HI3798MV200_FEMAC_CLK HISTB_ETH1_MAC_CLK +#define HI3798MV200_FEMACIF_CLK HISTB_ETH1_MACIF_CLK/* clocks provided by mcu CRG */ #define HISTB_MCE_CLK 1
Signature · 1 line
2.39.1
PATCH 4/4 arm: histb: hi3798mv200: add initial support for Hi3798MV200 HC2910-2AGHD05 board
In reply to a message not in the archiveA board with Hi3798MV200 SoC and various peripherals. Details are in the board README.md.
--- .../hi3798mv200-hc2910-2aghd05-u-boot.dtsi | 8 + arch/arm/dts/hi3798mv200-hc2910-2aghd05.dts | 71 ++++++ arch/arm/dts/hi3798mv200-u-boot.dtsi | 22 ++ arch/arm/dts/hi3798mv200.dtsi | 225 ++++++++++++++++++ arch/arm/mach-histb/Kconfig | 25 ++ board/skyworth/hc2910-2aghd05/Kconfig | 15 ++ board/skyworth/hc2910-2aghd05/MAINTAINERS | 6 + board/skyworth/hc2910-2aghd05/Makefile | 1 + board/skyworth/hc2910-2aghd05/README | 25 ++ .../skyworth/hc2910-2aghd05/hc2910-2aghd05.c | 26 ++ configs/hc2910_2aghd05_defconfig | 50 ++++ include/configs/hc2910-2aghd05.h | 6 + 12 files changed, 480 insertions(+) create mode 100644 arch/arm/dts/hi3798mv200-hc2910-2aghd05-u-boot.dtsi create mode 100644 arch/arm/dts/hi3798mv200-hc2910-2aghd05.dts create mode 100644 arch/arm/dts/hi3798mv200-u-boot.dtsi create mode 100644 arch/arm/dts/hi3798mv200.dtsi create mode 100644 board/skyworth/hc2910-2aghd05/Kconfig create mode 100644 board/skyworth/hc2910-2aghd05/MAINTAINERS create mode 100644 board/skyworth/hc2910-2aghd05/Makefile create mode 100644 board/skyworth/hc2910-2aghd05/README create mode 100644 board/skyworth/hc2910-2aghd05/hc2910-2aghd05.c create mode 100644 configs/hc2910_2aghd05_defconfig create mode 100644 include/configs/hc2910-2aghd05.h
arch/arm/dts/hi3798mv200-hc2910-2aghd05-u-boot.dtsi new file +8 -0
@@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include "hi3798mv200-u-boot.dtsi" + +/* The clock driver is missing */ +&sd0 { + status = "disabled"; +};
arch/arm/dts/hi3798mv200-hc2910-2aghd05.dts new file +71 -0
71 lines not on this page · raw message
arch/arm/dts/hi3798mv200-u-boot.dtsi new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * U-Boot addition to: + * 1) use platform data for the console + * + */ + +#include <dt-bindings/reset/ti-syscon.h> + +/* The driver in U-Boot does not support "snps,dw-mshc" compatible. */ +&sd0 { + compatible = "hisilicon,hi3798mv200-dw-mshc"; +}; + +&sd1 { + compatible = "hisilicon,hi3798mv200-dw-mshc"; +}; + +/* The clock driver is missing */ +&uart0 { + clock = <75000000>; +};
arch/arm/dts/hi3798mv200.dtsi new file +225 -0
225 lines not on this page · raw message
arch/arm/mach-histb/Kconfig +25 -0
@@ -11,4 +11,29 @@ config ARCH_HI3798MV2X endchoice +if ARCH_HI3798MV2X + +choice + prompt "Select a Hi3798M V2XX based board" + +config TARGET_HC2910_2AGHD05 + bool "Skyworth HC2910 with board label 2AGHD05" + help + Support for Skyworth HC2910 with board label 2AGHD05. This board features: + - Hisilicon Hi3798MV200 SoC (4xCortex-A53, Mali MP-450) + - 2GiB DRAM + - 8GiB eMMC, uSD slot + - Wifi and Bluetooth module + - 1x USB 2.0, 1x USB 3.0 host port + - HDMI + - SCI + - 3 LED - power, Wifi, Lock(?) + - 1x Fast Ethernet Controller, 1x GBe Ethernet Controller + +endchoice + +endif + +source "board/skyworth/hc2910-2aghd05/Kconfig" + endif
board/skyworth/hc2910-2aghd05/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_HC2910_2AGHD05 + +config SYS_BOARD + default "hc2910-2aghd05" + +config SYS_VENDOR + default "skyworth" + +config SYS_SOC + default "hi3798mv200" + +config SYS_CONFIG_NAME + default "hc2910-2aghd05" + +endif
board/skyworth/hc2910-2aghd05/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +HC2910 2AGHD05 BOARD +M: Yang Xiwen <[email protected]> +S: Maintained +F: board/skyworth/hc2910-2aghd05 +F: include/configs/hc2910-2aghd05.h +F: configs/hc2910_2aghd05_defconfig
board/skyworth/hc2910-2aghd05/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y := hc2910-2aghd05.o
board/skyworth/hc2910-2aghd05/README new file +25 -0
@@ -0,0 +1,25 @@ +================================================================================ + Board Information +================================================================================ + +The board features the Hi3798M V200 with an integrated quad-core 64-bit ARM +Cortex A53 processor. +SOC Hisilicon Hi3798CV200 +CPU Quad-core ARM Cortex-A53 64 bit +DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB +USB 1x USB 2.0 ports 1x USB 3.0 ports +CONSOLE USB-micro port for console support +ETHERNET 1 GBe Ethernet, 1 MBe Ethernet +WIFI 802.11n with Bluebooth +CONNECTORS One connector for Smart Card One connector for TSI + + +================================================================================ + BUILD INSTRUCTIONS +================================================================================ + +The U-Boot relies on a modified l-loader and TF-A for Hi3798MV200. +The source for l-loader can be obtained at: [l-loader](https://github.com/185264646/l-loader) +The mainline port for TF-A is still under development. For now, you can use the TF-A for poplar directly. + +For more information, please refer to <board/hisilicon/poplar/README>.
board/skyworth/hc2910-2aghd05/hc2910-2aghd05.c new file +26 -0
@@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Board init file for Skyworth HC2910 2AGHD05 +*/ + +#include <common.h> +#include <fdtdec.h> +#include <init.h> +#include <asm/system.h> +#include <linux/io.h> + +#define HI3798MV200_PERI_CTRL_BASE 0xf8a20000 +#define SDIO0_LDO_OFFSET 0x11c + +static int sdio0_set_ldo (void ) +{ +// SDIO LDO bypassed, 3.3V +writel (HI3798MV200_PERI_CTRL_BASE +SDIO0_LDO_OFFSET ,0x60 ); +return 0 ; +} + +int board_init (void ) +{ +sdio0_set_ldo (); +return 0 ; +}
configs/hc2910_2aghd05_defconfig new file +50 -0
50 lines not on this page · raw message
include/configs/hc2910-2aghd05.h new file +6 -0
@@ -0,0 +1,6 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef __HC2910_2AGHD05_CONFIG_H__ +#define __HC2910_2AGHD05_CONFIG_H__ + +#endif
Signature · 1 line
2.39.1