Skip to contentSkip to conversation

media: ov13b10: support new ACPI HID 'OVTI13B1'

PATCH RESEND New [email protected] 1 participant 3 messages May 26, 2023

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/3 media: ov13b10: support new ACPI HID 'OVTI13B1'

From: Bingbu Cao <[email protected]>

On ACPI systems, the HID of ov13b10 is 'OVTI13B1', add this new HID in acpi IDs table to make driver support it.

---
 drivers/media/i2c/ov13b10.c | 1 +
 1 file changed, 1 insertion(+)
drivers/media/i2c/ov13b10.c +1 -0
index c1430044fb1e..ede33899248c 100644
@@ -1484,6 +1484,7 @@ static const struct dev_pm_ops ov13b10_pm_ops = {
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id ov13b10_acpi_ids[] = {
 	{"OVTIDB10"},
+	{"OVTI13B1"},
 	{ /* sentinel */ }
 };
 
Signature · 1 line
2.40.1
#1 lore raw

PATCH RESEND 2/3 media: ov13b10: Defer probe if no endpoint found

From: Bingbu Cao <[email protected]>

The ov13b10 need be connected to a CIO2 or IPU device by bridge, sometimes the bridge driver was not probed before ov13b10 driver, then the absence of the fwnode endpoint for this device is expected, so driver return -EPROBE_DEFER in this case to let the probe occur after bridge driver.

---
 drivers/media/i2c/ov13b10.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/media/i2c/ov13b10.c +4 -4
index ede33899248c..2d48c94659a4 100644
@@ -1331,6 +1331,10 @@ static int ov13b10_check_hwcfg(struct device *dev)
 	if (!fwnode)
 		return -ENXIO;
 
+	ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+	if (!ep)
+		return -EPROBE_DEFER;
+
 	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
 				       &ext_clk);
 	if (ret) {
@@ -1344,10 +1348,6 @@ static int ov13b10_check_hwcfg(struct device *dev)
 		return -EINVAL;
 	}
 
-	ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
-	if (!ep)
-		return -ENXIO;
-
 	ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
 	fwnode_handle_put(ep);
 	if (ret)
Signature · 1 line
2.40.1
#2 lore raw

PATCH RESEND 3/3 media: ov13b10: add PM control support based on power resources

In reply to [email protected]

From: Bingbu Cao <[email protected]>

On ACPI based platforms, the ov13b10 camera sensor need to be powered up by acquire the PM resource from INT3472. On such platform, 1 GPIO can be used to enable AVDD and DOVDD, 1 GPIO to reset, we just have one power supply 'vdd' for camera. Add 2 power interfaces and also registered as runtime PM callbacks to support that.

---
 drivers/media/i2c/ov13b10.c | 98 ++++++++++++++++++++++++++++++++++++-
 1 file changed, 96 insertions(+), 2 deletions(-)
drivers/media/i2c/ov13b10.c +96 -2
index 2d48c94659a4..b1faa89a3571 100644
@@ -2,6 +2,9 @@
 // Copyright (c) 2021 Intel Corporation.
 
 #include <linux/acpi.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/pm_runtime.h>
@@ -573,6 +576,11 @@ struct ov13b10 {
 	struct media_pad pad;
 
 	struct v4l2_ctrl_handler ctrl_handler;
+
+	struct clk *img_clk;
+	struct regulator *vdd;
+	struct gpio_desc *reset;
+
 	/* V4L2 Controls */
 	struct v4l2_ctrl *link_freq;
 	struct v4l2_ctrl *pixel_rate;
@@ -1051,6 +1059,50 @@ static int ov13b10_identify_module(struct ov13b10 *ov13b)
 	return 0;
 }
 
+static int ov13b10_power_off(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov13b10 *ov13b10 = to_ov13b10(sd);
+
+	if (!ov13b10->vdd || !ov13b10->reset || !ov13b10->img_clk)
+		return 0;
+
+	gpiod_set_value_cansleep(ov13b10->reset, 1);
+	regulator_disable(ov13b10->vdd);
+	clk_disable_unprepare(ov13b10->img_clk);
+
+	return 0;
+}
+
+static int ov13b10_power_on(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov13b10 *ov13b10 = to_ov13b10(sd);
+	int ret;
+
+	if (!ov13b10->vdd || !ov13b10->reset || !ov13b10->img_clk)
+		return 0;
+
+	ret = clk_prepare_enable(ov13b10->img_clk);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable imaging clock: %d", ret);
+		return ret;
+	}
+
+	ret = regulator_enable(ov13b10->vdd);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable vdd: %d", ret);
+		return ret;
+	}
+
+	gpiod_set_value_cansleep(ov13b10->reset, 0);
+
+	/* 5ms to wait ready after XSHUTDN assert */
+	usleep_range(5000, 5500);
+
+	return 0;
+}
+
 static int ov13b10_start_streaming(struct ov13b10 *ov13b)
 {
 	struct i2c_client *client = v4l2_get_subdevdata(&ov13b->sd);
@@ -1317,6 +1369,37 @@ static void ov13b10_free_controls(struct ov13b10 *ov13b)
 	mutex_destroy(&ov13b->mutex);
 }
 
+static void ov13b10_get_pm_resources(struct device *dev)
+{
+	struct v4l2_subdev *sd = dev_get_drvdata(dev);
+	struct ov13b10 *ov13b = to_ov13b10(sd);
+
+	if (!is_acpi_node(dev_fwnode(dev)))
+		return;
+
+	ov13b->reset = devm_gpiod_get_optional(dev, "reset",
+					       GPIOD_OUT_LOW);
+	if (IS_ERR(ov13b->reset)) {
+		dev_dbg(dev, "failed to get reset gpio: %ld",
+			PTR_ERR(ov13b->reset));
+		ov13b->reset = NULL;
+	}
+
+	ov13b->img_clk = devm_clk_get_optional(dev, NULL);
+	if (IS_ERR(ov13b->img_clk)) {
+		dev_dbg(dev, "failed to get imaging clock: %ld",
+			PTR_ERR(ov13b->img_clk));
+		ov13b->img_clk = NULL;
+	}
+
+	ov13b->vdd = devm_regulator_get_optional(dev, "vdd");
+	if (IS_ERR(ov13b->vdd)) {
+		dev_dbg(dev, "failed to get vdd regulator: %ld",
+			PTR_ERR(ov13b->vdd));
+		ov13b->vdd = NULL;
+	}
+}
+
 static int ov13b10_check_hwcfg(struct device *dev)
 {
 	struct v4l2_fwnode_endpoint bus_cfg = {
@@ -1407,13 +1490,21 @@ static int ov13b10_probe(struct i2c_client *client)
 	/* Initialize subdev */
 	v4l2_i2c_subdev_init(&ov13b->sd, client, &ov13b10_subdev_ops);
 
+	ov13b10_get_pm_resources(&client->dev);
+
 	full_power = acpi_dev_state_d0(&client->dev);
 	if (full_power) {
+		ov13b10_power_on(&client->dev);
+		if (ret) {
+			dev_err(&client->dev, "failed to power on\n");
+			goto error_power_off;
+		}
+
 		/* Check module identity */
 		ret = ov13b10_identify_module(ov13b);
 		if (ret) {
 			dev_err(&client->dev, "failed to find sensor: %d\n", ret);
-			return ret;
+			goto error_power_off;
 		}
 	}
 
@@ -1422,7 +1513,7 @@ static int ov13b10_probe(struct i2c_client *client)
 
 	ret = ov13b10_init_controls(ov13b);
 	if (ret)
-		return ret;
+		goto error_power_off;
 
 	/* Initialize subdev */
 	ov13b->sd.internal_ops = &ov13b10_internal_ops;
@@ -1461,6 +1552,8 @@ static int ov13b10_probe(struct i2c_client *client)
 error_handler_free:
 	ov13b10_free_controls(ov13b);
 	dev_err(&client->dev, "%s failed:%d\n", __func__, ret);
+error_power_off:
+	ov13b10_power_off(&client->dev);
 
 	return ret;
 }
@@ -1479,6 +1572,7 @@ static void ov13b10_remove(struct i2c_client *client)
 
 static const struct dev_pm_ops ov13b10_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(ov13b10_suspend, ov13b10_resume)
+	SET_RUNTIME_PM_OPS(ov13b10_power_off, ov13b10_power_on, NULL)
 };
 
 #ifdef CONFIG_ACPI
Signature · 1 line
2.40.1