Skip to contentSkip to conversation

io_uring: Use io_schedule* in cqring wait

PATCH Applied Andres Freund 2 participants 3 messages Jul 7, 2023 io_uring

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 io_uring: Use io_schedule* in cqring wait

I observed poor performance of io_uring compared to synchronous IO. That turns out to be caused by deeper CPU idle states entered with io_uring, due to io_uring using plain schedule(), whereas synchronous IO uses io_schedule().

The losses due to this are substantial. On my cascade lake workstation, t/io_uring from the fio repository e.g. yields regressions between 20% and 40% with the following command:
./t/io_uring -r 5 -X0 -d 1 -s 1 -c 1 -p 0 -S$use_sync -R 0 /mnt/t2/fio/write.0.0

This is repeatable with different filesystems, using raw block devices and using different block devices.

Use io_schedule_prepare() / io_schedule_finish() in io_cqring_wait_schedule() to address the difference.

After that using io_uring is on par or surpassing synchronous IO (using registered files etc makes it reliably win, but arguably is a less fair comparison).

There are other calls to schedule() in io_uring/, but none immediately jump out to be similarly situated, so I did not touch them. Similarly, it's possible that mutex_lock_io() should be used, but it's not clear if there are cases where that matters.

---
 io_uring/io_uring.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)
io_uring/io_uring.c +14 -2
index 3bca7a79efda..4661a39de716 100644
@@ -2575,6 +2575,9 @@ int io_run_task_work_sig(struct io_ring_ctx *ctx)
 static inline int io_cqring_wait_schedule(struct io_ring_ctx *ctx,
 					  struct io_wait_queue *iowq)
 {
+	int ret;
+	int token;
+
 	if (unlikely(READ_ONCE(ctx->check_cq)))
 		return 1;
 	if (unlikely(!llist_empty(&ctx->work_llist)))
@@ -2585,11 +2588,20 @@ static inline int io_cqring_wait_schedule(struct io_ring_ctx *ctx,
 		return -EINTR;
 	if (unlikely(io_should_wake(iowq)))
 		return 0;
+
+	/*
+	 * Use io_schedule_prepare/finish, so cpufreq can take into account
+	 * that the task is waiting for IO - turns out to be important for low
+	 * QD IO.
+	 */
+	token = io_schedule_prepare();
+	ret = 0;
 	if (iowq->timeout == KTIME_MAX)
 		schedule();
 	else if (!schedule_hrtimeout(&iowq->timeout, HRTIMER_MODE_ABS))
-		return -ETIME;
-	return 0;
+		ret = -ETIME;
+	io_schedule_finish(token);
+	return ret;
 }
 
 /*
Signature · 1 line
2.38.0
maintainer
#1 lore raw
Quoted 16 lines · Andres Freund

I observed poor performance of io_uring compared to synchronous IO. That turns out to be caused by deeper CPU idle states entered with io_uring, due to io_uring using plain schedule(), whereas synchronous IO uses io_schedule().

The losses due to this are substantial. On my cascade lake workstation, t/io_uring from the fio repository e.g. yields regressions between 20% and 40% with the following command:
./t/io_uring -r 5 -X0 -d 1 -s 1 -c 1 -p 0 -S$use_sync -R 0 /mnt/t2/fio/write.0.0

This is repeatable with different filesystems, using raw block devices and using different block devices.

Use io_schedule_prepare() / io_schedule_finish() in io_cqring_wait_schedule() to address the difference.

Quoted 8 lines

After that using io_uring is on par or surpassing synchronous IO (using registered files etc makes it reliably win, but arguably is a less fair comparison).

There are other calls to schedule() in io_uring/, but none immediately jump out to be similarly situated, so I did not touch them. Similarly, it's possible that mutex_lock_io() should be used, but it's not clear if there are cases where that matters.

This looks good to me, and I also separately tested a similar patch and it showed good results for me even with a heavily performance oriented setup:

pread2 io_uring io_uring w/io_sched
QD1 185K 170K 186K
QD2 NA 304K 327K
QD4 NA 630K 640K
QD8 NA 891K 892K

I'll add this, with just one small minor cosmetic edit:

io_uring/io_uring.c int io_run_task_work_sig(struct io_ring_ctx *ctx) · line 2579

Quoted 6 lines
io_uring/io_uring.c +2 -0
@@ -2575,6 +2575,9 @@ int io_run_task_work_sig(struct io_ring_ctx *ctx)
 static inline int io_cqring_wait_schedule(struct io_ring_ctx *ctx,
 					  struct io_wait_queue *iowq)
 {
+	int ret;
+	int token;

Should just be a single line.

And I'll mark this for stable as well. Thanks!

Signature · 1 line
Jens Axboe
maintainer Applied
#2 lore raw
In reply to Andres Freund
Quoted 11 lines · Andres Freund

I observed poor performance of io_uring compared to synchronous IO. That turns out to be caused by deeper CPU idle states entered with io_uring, due to io_uring using plain schedule(), whereas synchronous IO uses io_schedule().

The losses due to this are substantial. On my cascade lake workstation, t/io_uring from the fio repository e.g. yields regressions between 20% and 40% with the following command:
./t/io_uring -r 5 -X0 -d 1 -s 1 -c 1 -p 0 -S$use_sync -R 0 /mnt/t2/fio/write.0.0

[...]

Applied, thanks!

[1/1] io_uring: Use io_schedule* in cqring wait
(no commit info)

Best regards,

Signature · 1 line
Jens Axboe