Add StarFive VF2 USB host support.
PATCH RESEND 1/4 pci: plda: Get correct ECAM offset in multiple PCIe RC case
In reply to Minda ChenGet the correct ECAM offset and record the secondary bus number in Multiple RC case.
--- drivers/pci/pcie_plda_common.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/pci/pcie_plda_common.c +3 -2
@@ -36,8 +36,8 @@ static int plda_pcie_conf_address(const struct udevice *udev, pci_dev_t bdf, uint offset, void **paddr) { struct pcie_plda *priv = dev_get_priv(udev); -int where =PCIE_ECAM_OFFSET (PCI_BUS (bdf),PCI_DEV (bdf), -PCI_FUNC (bdf), offset); +int where =PCIE_ECAM_OFFSET (PCI_BUS (bdf) -dev_seq (udev), +PCI_DEV (bdf),PCI_FUNC (bdf), offset);if (!plda_pcie_addr_valid (priv, bdf))return -ENODEV ;
@@ -71,6 +71,7 @@ int plda_pcie_config_write(struct udevice *udev, pci_dev_t bdf, (offset == PCI_PRIMARY_BUS && size != PCI_SIZE_8))) { priv->sec_busno = ((offset ==PCI_PRIMARY_BUS ) ? (value >>8 ) : value) &0xff ; + priv->sec_busno +=dev_seq (udev);debug ("Secondary bus number was changed to %d\n" , priv->sec_busno); }
Signature · 1 line
2.17.1
cover Add StarFive VF2 USB host support.
StarFive VF2 VLI usb-host controller connect to pcie0 RC. Enable pcie0 first the enable USB function.
patch1 is Get the correct ECAM offset in multiple PCIe RC. patch2 is enable pcie0 dts node.
patch3 is enable SYS_CACHELINE_SIZE
patch4 is Add VF2 USB related configuration.
Minda Chen (4):
pci: plda: Get correct ECAM offset in multiple PCIe RC case
riscv: dts: starfive: Enable pcie0 dts node
riscv: starfive: Add SYS_CACHE_SHIFT_6 to enable SYS_CACHELINE_SIZE
configs: riscv: starfive: Add VF2 PCIe USB3 XHCI support
arch/riscv/cpu/jh7110/Kconfig | 1 + arch/riscv/dts/jh7110-starfive-visionfive-2.dtsi | 2 +- configs/starfive_visionfive2_defconfig | 5 +++++ drivers/pci/pcie_plda_common.c | 5 +++-- 4 files changed, 10 insertions(+), 3 deletions(-)
base-commit: 38dedebc547f795efc3daad17f7c013c515e1285
Signature · 1 line
2.17.1
PATCH RESEND 4/4 configs: riscv: starfive: Add VF2 PCIe USB3 XHCI support
Add XHCI_PCI to enable usb3-host functions.
Also add usb command and keyboard config.
--- configs/starfive_visionfive2_defconfig | 5 +++++ 1 file changed, 5 insertions(+)
configs/starfive_visionfive2_defconfig +5 -0
@@ -65,6 +65,7 @@ CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 CONFIG_CMD_MEMINFO=y CONFIG_CMD_I2C=y CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y CONFIG_CMD_TFTPPUT=y CONFIG_OF_BOARD=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y
@@ -111,3 +112,7 @@ CONFIG_PINCTRL_STARFIVE=y CONFIG_SYS_NS16550=y CONFIG_CADENCE_QSPI=y CONFIG_TIMER_EARLY=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y +CONFIG_USB_KEYBOARD=y
Signature · 1 line
2.17.1
PATCH RESEND 3/4 riscv: starfive: Add SYS_CACHE_SHIFT_6 to enable SYS_CACHELINE_SIZE
In reply to Minda ChenSome device driver need SYS_CACHELINE_SIZE macro. Add StarFive SYS_CACHE_SHIFT_6 to enable it.
--- arch/riscv/cpu/jh7110/Kconfig | 1 + 1 file changed, 1 insertion(+)
arch/riscv/cpu/jh7110/Kconfig +1 -0
@@ -13,6 +13,7 @@ config STARFIVE_JH7110 select SUPPORT_SPL select SPL_RAM if SPL select SPL_STARFIVE_DDR + select SYS_CACHE_SHIFT_6 select PINCTRL_STARFIVE_JH7110 imply MMC imply MMC_BROKEN_CD
Signature · 1 line
2.17.1
PATCH RESEND 2/4 riscv: dts: starfive: Enable pcie0 dts node
In reply to Minda ChenIn StarFive VF2 board. pcie0 connect to VTI usb controller. Enable it to support usb host.
--- arch/riscv/dts/jh7110-starfive-visionfive-2.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/riscv/dts/jh7110-starfive-visionfive-2.dtsi +1 -1
@@ -311,7 +311,7 @@ &pcie0 { reset-gpios = <&sysgpio 26 GPIO_ACTIVE_LOW>; - status = "disabled"; + status = "okay"; }; &pcie1 {
Signature · 1 line
2.17.1
Re: [RESEND, v1 3/4] riscv: starfive: Add SYS_CACHE_SHIFT_6 to enable SYS_CACHELINE_SIZE
In reply to Minda ChenQuoted 9 lines · Minda Chen
Some device driver need
SYS_CACHELINE_SIZEmacro. Add StarFiveSYS_CACHE_SHIFT_6to enable it.Signed-off-by Minda Chen <[email protected]>--- arch/riscv/cpu/jh7110/Kconfig | 1 + 1 file changed, 1 insertion(+)
Re: [RESEND,v1 1/4] pci: plda: Get correct ECAM offset in multiple PCIe RC case
In reply to Minda ChenQuoted 7 lines · Minda Chen
Get the correct ECAM offset and record the secondary bus number in Multiple RC case.
Signed-off-by Minda Chen <[email protected]>--- drivers/pci/pcie_plda_common.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
Re: [RESEND,v1 2/4] riscv: dts: starfive: Enable pcie0 dts node
In reply to Minda ChenQuoted 7 lines · Minda Chen
In StarFive VF2 board. pcie0 connect to VTI usb controller. Enable it to support usb host.
Signed-off-by Minda Chen <[email protected]>--- arch/riscv/dts/jh7110-starfive-visionfive-2.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
Re: [RESEND, v1 3/4] riscv: starfive: Add SYS_CACHE_SHIFT_6 to enable SYS_CACHELINE_SIZE
In reply to Minda ChenQuoted 7 lines · Minda Chen
Some device driver need
SYS_CACHELINE_SIZEmacro. Add StarFiveSYS_CACHE_SHIFT_6to enable it.Signed-off-by Minda Chen <[email protected]>--- arch/riscv/cpu/jh7110/Kconfig | 1 + 1 file changed, 1 insertion(+)
Re: [RESEND, v1 4/4] configs: riscv: starfive: Add VF2 PCIe USB3 XHCI support
In reply to Minda ChenQuoted 7 lines · Minda Chen
Add
XHCI_PCIto enable usb3-host functions.
Also add usb command and keyboard config.Signed-off-by Minda Chen <[email protected]>--- configs/starfive_visionfive2_defconfig | 5 +++++ 1 file changed, 5 insertions(+)