Skip to contentSkip to conversation

mips-kexec-refactor-for-kernel-kconfigkexec.patch removed from -mm tree

merged mm-nonmm-stable Andrew Morton 1 participant 1 message Aug 12, 2023

lore
Share & tools
lore

Andrew Morton

author tree notice Applied
#0 lore raw

The quilt patch titled
Subject: mips/kexec: refactor for kernel/Kconfig.kexec
has been removed from the -mm tree. Its filename was
mips-kexec-refactor-for-kernel-kconfigkexec.patch

This patch was dropped because it was merged into the mm-nonmm-stable branch of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

------------------------------------------------------
From: Eric DeVolder <[email protected]>
Subject: mips/kexec: refactor for kernel/Kconfig.kexec
Date: Wed, 12 Jul 2023 12:15:39 -0400

The kexec and crash kernel options are provided in the common kernel/Kconfig.kexec. Utilize the common options and provide the ARCH_SUPPORTS_ and ARCH_SELECTS_ entries to recreate the equivalent set of KEXEC and CRASH options.

---

 arch/mips/Kconfig |   30 ++++--------------------------
 1 file changed, 4 insertions(+), 26 deletions(-)
arch/mips/Kconfig renamed from arch/mips/Kconfig~mips-kexec-refactor-for-kernel-kconfigkexec +4 -26
@@ -2878,33 +2878,11 @@ config HZ
 config SCHED_HRTICK
 	def_bool HIGH_RES_TIMERS
 
-config KEXEC
-	bool "Kexec system call"
-	select KEXEC_CORE
-	help
-	  kexec is a system call that implements the ability to shutdown your
-	  current kernel, and to start another kernel.  It is like a reboot
-	  but it is independent of the system firmware.   And like a reboot
-	  you can start any kernel with it, not just Linux.
+config ARCH_SUPPORTS_KEXEC
+	def_bool y
 
-	  The name comes from the similarity to the exec system call.
-
-	  It is an ongoing process to be certain the hardware in a machine
-	  is properly shutdown, so do not be surprised if this code does not
-	  initially work for you.  As of this writing the exact hardware
-	  interface is strongly in flux, so no good recommendation can be
-	  made.
-
-config CRASH_DUMP
-	bool "Kernel crash dumps"
-	help
-	  Generate crash dump after being started by kexec.
-	  This should be normally only set in special crash dump kernels
-	  which are loaded in the main kernel with kexec-tools into
-	  a specially reserved region and then later executed after
-	  a crash by kdump/kexec. The crash dump kernel must be compiled
-	  to a memory address not used by the main kernel or firmware using
-	  PHYSICAL_START.
+config ARCH_SUPPORTS_CRASH_DUMP
+	def_bool y
 
 config PHYSICAL_START
 	hex "Physical address where the kernel is loaded"

_

Patches currently in -mm which might be from [email protected] are

crash-move-a-few-code-bits-to-setup-support-of-crash-hotplug.patch crash-add-generic-infrastructure-for-crash-hotplug-support.patch kexec-exclude-elfcorehdr-from-the-segment-digest.patch crash-memory-and-cpu-hotplug-sysfs-attributes.patch x86-crash-add-x86-crash-hotplug-support.patch crash-hotplug-support-for-kexec_load.patch crash-change-crash_prepare_elf64_headers-to-for_each_possible_cpu.patch x86-crash-optimize-cpu-changes.patch