Skip to contentSkip to conversation

Add I2S support for the StarFive JH7110 SoC

PATCH Applied Xingyu Wu 6 participants 12 messages Aug 21, 2023 – Sep 13, 2023

Subsystems (5)
lore
Share & tools
lore

Xingyu Wu

author
#0 lore raw

v2 cover Add I2S support for the StarFive JH7110 SoC

This patch series adds I2S support for the StarFive JH7110 RISC-V SoC based on Designware I2S controller. There has three I2S channels (RX/TX0/TX1) on the JH7110 SoC, one of which is for record(RX) and two for playback(TX).

The first patch adds support for the StarFive JH7110 SoC in the Designware I2S bindings.
The second patch adds the ops to get data from platform bus in the I2S driver.
The third patch adds support for the StarFive JH7110 SoC in the Designware I2S driver.
The fourth patch fixes the name of I2STX1 pinmux.
The last patch adds device node of I2S RX/TX0/TX1 in JH7110 dts.

This patch series is based on Linux-next(20230818) which is merge clock, syscon and dma nodes for the StarFive JH7110 SoC.

The series has been tested and works normally on the VisionFive 2 board by plugging an audio expansion board.

Changes since v1:
- Added the maxItems of clocks, clock-names and resets on each I2S controllers in the binding.
- Dropped the useless settings about dma bus width in the I2S driver.
- Used the 'i2s@' instead of 'i2stx@' or 'i2srx@' in the JH7110 dts.

v1: https://lore.kernel.org/all/[email protected]/

Xingyu Wu (5):
ASoC: dt-bindings: snps,designware-i2s: Add StarFive JH7110 SoC
support
ASoC: dwc: Use ops to get platform data
ASoC: dwc: i2s: Add StarFive JH7110 SoC support
riscv: dts: starfive: pinfunc: Fix the pins name of I2STX1
riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1

 .../bindings/sound/snps,designware-i2s.yaml   | 108 ++++++-
 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h |   4 +-
 .../jh7110-starfive-visionfive-2.dtsi         |  58 ++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      |  65 ++++
 include/sound/designware_i2s.h                |   3 +
 sound/soc/dwc/dwc-i2s.c                       | 306 ++++++++++++++++--
 sound/soc/dwc/local.h                         |   1 +
 7 files changed, 518 insertions(+), 27 deletions(-)
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH v2 1/5 ASoC: dt-bindings: snps,designware-i2s: Add StarFive JH7110 SoC support

Add the StarFive JH7110 (TX0/TX1/RX channel) SoC support in the bindings of Designware I2S controller. The I2S controller needs two reset items to work properly on the JH7110 SoC. And TX0 channel as master mode needs 5 clock items and TX1/RX channels as slave mode need 9 clock items on the JH7110 SoC. The RX channel needs System Register Controller property to enable it and other platforms do not need it.

---
 .../bindings/sound/snps,designware-i2s.yaml   | 108 +++++++++++++++++-
 1 file changed, 105 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/sound/snps,designware-i2s.yaml +105 -3
index a970fd264b21..a48d040b0a4f 100644
@@ -17,6 +17,9 @@ properties:
           - const: snps,designware-i2s
       - enum:
           - snps,designware-i2s
+          - starfive,jh7110-i2stx0
+          - starfive,jh7110-i2stx1
+          - starfive,jh7110-i2srx
 
   reg:
     maxItems: 1
@@ -29,15 +32,36 @@ properties:
     maxItems: 1
 
   clocks:
-    description: Sampling rate reference clock
-    maxItems: 1
+    items:
+      - description: Sampling rate reference clock
+      - description: APB clock
+      - description: Audio master clock
+      - description: Inner audio master clock source
+      - description: External audio master clock source
+      - description: Bit clock
+      - description: Left/right channel clock
+      - description: External bit clock
+      - description: External left/right channel clock
+    minItems: 1
 
   clock-names:
-    const: i2sclk
+    items:
+      - const: i2sclk
+      - const: apb
+      - const: mclk
+      - const: mclk_inner
+      - const: mclk_ext
+      - const: bclk
+      - const: lrck
+      - const: bclk_ext
+      - const: lrck_ext
+    minItems: 1
 
   resets:
     items:
       - description: Optional controller resets
+      - description: controller reset of Sampling rate
+    minItems: 1
 
   dmas:
     items:
@@ -51,6 +75,17 @@ properties:
       - const: rx
     minItems: 1
 
+  starfive,syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to System Register Controller sys_syscon node.
+          - description: I2S-rx enabled control offset of SYS_SYSCONSAIF__SYSCFG register.
+          - description: I2S-rx enabled control mask
+    description:
+      The phandle to System Register Controller syscon node and the I2S-rx(ADC)
+      enabled control offset and mask of SYS_SYSCONSAIF__SYSCFG register.
+
 allOf:
   - $ref: dai-common.yaml#
   - if:
@@ -66,6 +101,73 @@ allOf:
       properties:
         "#sound-dai-cells":
           const: 0
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: snps,designware-i2s
+    then:
+      properties:
+        clocks:
+          maxItems: 1
+        clock-names:
+          maxItems: 1
+        resets:
+          maxItems: 1
+    else:
+      properties:
+        resets:
+          minItems: 2
+          maxItems: 2
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: starfive,jh7110-i2stx0
+    then:
+      properties:
+        clocks:
+          minItems: 5
+          maxItems: 5
+        clock-names:
+          minItems: 5
+          maxItems: 5
+      required:
+        - resets
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: starfive,jh7110-i2stx1
+    then:
+      properties:
+        clocks:
+          minItems: 9
+          maxItems: 9
+        clock-names:
+          minItems: 9
+          maxItems: 9
+      required:
+        - resets
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: starfive,jh7110-i2srx
+    then:
+      properties:
+        clocks:
+          minItems: 9
+          maxItems: 9
+        clock-names:
+          minItems: 9
+          maxItems: 9
+      required:
+        - resets
+        - starfive,syscon
+    else:
+      properties:
+        starfive,syscon: false
 
 required:
   - compatible
Signature · 1 line
2.25.1
Reviewed-by on v2 1/5
#2 lore raw

Re: [PATCH v2 1/5] ASoC: dt-bindings: snps,designware-i2s: Add StarFive JH7110 SoC support

Quoted 8 lines · Xingyu Wu

Add the StarFive JH7110 (TX0/TX1/RX channel) SoC support in the bindings of Designware I2S controller. The I2S controller needs two reset items to work properly on the JH7110 SoC. And TX0 channel as master mode needs 5 clock items and TX1/RX channels as slave mode need 9 clock items on the JH7110 SoC. The RX channel needs System Register Controller property to enable it and other platforms do not need it.

Best regards,
Krzysztof

author
#3 lore raw

PATCH v2 2/5 ASoC: dwc: Use ops to get platform data

In reply to Xingyu Wu

Use of_device_get_match_data() to get platform data.

---
 sound/soc/dwc/dwc-i2s.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
sound/soc/dwc/dwc-i2s.c +1 -1
index 0a4698008d64..e70d41d57dfd 100644
@@ -691,7 +691,7 @@ static int dw_configure_dai_by_dt(struct dw_i2s_dev *dev,
 
 static int dw_i2s_probe(struct platform_device *pdev)
 {
-	const struct i2s_platform_data *pdata = pdev->dev.platform_data;
+	const struct i2s_platform_data *pdata = of_device_get_match_data(&pdev->dev);
 	struct dw_i2s_dev *dev;
 	struct resource *res;
 	int ret, irq;
Signature · 1 line
2.25.1
author
#4 lore raw

PATCH v2 3/5 ASoC: dwc: i2s: Add StarFive JH7110 SoC support

In reply to Xingyu Wu

Add StarFive JH7110(TX0/TX1/RX channels) SoC support in the designware I2S driver and a flag to check if it is on the JH7110 SoC.

These channels need to enable clocks, resets and syscon register on the JH7110 SoC. So add init ops in platform data for the JH7110 SoC to do this.

Their resets should be deassert before changing the parent of clocks so these are done in the init ops of platform data.

The I2S controllers use DMA controller by platform data on the JH7110 and their settings about snd_dmaengine_dai_dma_data() should be added in the dw_configure_dai_by_pd(). And use dmaengine PCM registration if these do not have IRQ on the JH7110 SoC.

---
 include/sound/designware_i2s.h |   3 +
 sound/soc/dwc/dwc-i2s.c        | 304 ++++++++++++++++++++++++++++++---
 sound/soc/dwc/local.h          |   1 +
 3 files changed, 287 insertions(+), 21 deletions(-)
include/sound/designware_i2s.h +3 -0
index 80d275b9ae0d..f6803205a9fb 100644
@@ -21,6 +21,8 @@ struct i2s_clk_config_data {
 	u32 sample_rate;
 };
 
+struct dw_i2s_dev;
+
 struct i2s_platform_data {
 	#define DWC_I2S_PLAY	(1 << 0)
 	#define DWC_I2S_RECORD	(1 << 1)
@@ -42,6 +44,7 @@ struct i2s_platform_data {
 	void *capture_dma_data;
 	bool (*filter)(struct dma_chan *chan, void *slave);
 	int (*i2s_clk_cfg)(struct i2s_clk_config_data *config);
+	int (*i2s_pd_init)(struct dw_i2s_dev *dev);
 };
 
 struct i2s_dma_data {
sound/soc/dwc/dwc-i2s.c +283 -21

368 lines not on this page · raw message

sound/soc/dwc/local.h +1 -0
index 4ce96bac2f39..dce88c9ad5f3 100644
@@ -123,6 +123,7 @@ struct dw_i2s_dev {
 	u32 fifo_th;
 	u32 l_reg;
 	u32 r_reg;
+	bool is_jh7110; /* Flag for StarFive JH7110 SoC */
 
 	/* data related to DMA transfers b/w i2s and DMAC */
 	union dw_i2s_snd_dma_data play_dma_data;
Signature · 1 line
2.25.1
author
#5 lore raw

PATCH v2 4/5 riscv: dts: starfive: pinfunc: Fix the pins name of I2STX1

In reply to Xingyu Wu

These pins are actually I2STX1 clock input, not I2STX0, so their names should be changed.

---
 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/riscv/boot/dts/starfive/jh7110-pinfunc.h +2 -2
index fb0139b56723..256de17f5261 100644
@@ -240,8 +240,8 @@
 #define GPI_SYS_MCLK_EXT			30
 #define GPI_SYS_I2SRX_BCLK			31
 #define GPI_SYS_I2SRX_LRCK			32
-#define GPI_SYS_I2STX0_BCLK			33
-#define GPI_SYS_I2STX0_LRCK			34
+#define GPI_SYS_I2STX1_BCLK			33
+#define GPI_SYS_I2STX1_LRCK			34
 #define GPI_SYS_TDM_CLK				35
 #define GPI_SYS_TDM_RXD				36
 #define GPI_SYS_TDM_SYNC			37
Signature · 1 line
2.25.1
Reviewed-by on v2 4/5
#6 lore raw

Re: [PATCH v2 4/5] riscv: dts: starfive: pinfunc: Fix the pins name of I2STX1

Quoted 13 lines · Xingyu Wu

These pins are actually I2STX1 clock input, not I2STX0, so their names should be changed.

---
 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/riscv/boot/dts/starfive/jh7110-pinfunc.h +0 -0
index fb0139b56723..256de17f5261 100644

arch/riscv/boot/dts/starfive/jh7110-pinfunc.h line 247

Quoted 10 lines
arch/riscv/boot/dts/starfive/jh7110-pinfunc.h +2 -2
@@ -240,8 +240,8 @@
 #define GPI_SYS_MCLK_EXT			30
 #define GPI_SYS_I2SRX_BCLK			31
 #define GPI_SYS_I2SRX_LRCK			32
-#define GPI_SYS_I2STX0_BCLK			33
-#define GPI_SYS_I2STX0_LRCK			34
+#define GPI_SYS_I2STX1_BCLK			33
+#define GPI_SYS_I2STX1_LRCK			34
 #define GPI_SYS_TDM_CLK				35
 #define GPI_SYS_TDM_RXD				36
 #define GPI_SYS_TDM_SYNC			37

Thanks!

maintainer Acked-by on v2 4/5
#7 lore raw

Re: [PATCH v2 4/5] riscv: dts: starfive: pinfunc: Fix the pins name of I2STX1

In reply to Xingyu Wu
Quoted 8 lines · Xingyu Wu

These pins are actually I2STX1 clock input, not I2STX0, so their names should be changed.

---
 arch/riscv/boot/dts/starfive/jh7110-pinfunc.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv

author
#8 lore raw

PATCH v2 5/5 riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1

In reply to Xingyu Wu

Add I2Srx/I2Stx0/I2Stx1 nodes and pins configuration for the StarFive JH7110 SoC.

---
 .../jh7110-starfive-visionfive-2.dtsi         | 58 +++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      | 65 +++++++++++++++++++
 2 files changed, 123 insertions(+)
arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +58 -0
index d79f94432b27..7179f1a31cf2 100644
@@ -203,6 +203,24 @@ &i2c6 {
 	status = "okay";
 };
 
+&i2srx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2srx_pins>;
+	status = "okay";
+};
+
+&i2stx0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mclk_ext_pins>;
+	status = "okay";
+};
+
+&i2stx1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2stx1_pins>;
+	status = "okay";
+};
+
 &mmc0 {
 	max-frequency = <100000000>;
 	bus-width = <8>;
@@ -337,6 +355,46 @@ GPOEN_SYS_I2C6_DATA,
 		};
 	};
 
+	i2srx_pins: i2srx-0 {
+		clk-sd-pins {
+			pinmux = <GPIOMUX(38, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_BCLK)>,
+				 <GPIOMUX(63, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_LRCK)>,
+				 <GPIOMUX(38, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2STX1_BCLK)>,
+				 <GPIOMUX(63, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2STX1_LRCK)>,
+				 <GPIOMUX(61, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_SDIN0)>;
+			input-enable;
+		};
+	};
+
+	i2stx1_pins: i2stx1-0 {
+		sd-pins {
+			pinmux = <GPIOMUX(44, GPOUT_SYS_I2STX1_SDO0,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	mclk_ext_pins: mclk-ext-0 {
+		mclk-ext-pins {
+			pinmux = <GPIOMUX(4, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_MCLK_EXT)>;
+			input-enable;
+		};
+	};
+
 	mmc0_pins: mmc0-0 {
 		 rst-pins {
 			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
arch/riscv/boot/dts/starfive/jh7110.dtsi +65 -0

77 lines not on this page · raw message

Signature · 1 line
2.25.1
Reviewed-by on v2 5/5
#9 lore raw

Re: [PATCH v2 5/5] riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1

Quoted 158 lines · Xingyu Wu

Add I2Srx/I2Stx0/I2Stx1 nodes and pins configuration for the StarFive JH7110 SoC.

---
 .../jh7110-starfive-visionfive-2.dtsi         | 58 +++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      | 65 +++++++++++++++++++
 2 files changed, 123 insertions(+)
arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +58 -0
index d79f94432b27..7179f1a31cf2 100644
@@ -203,6 +203,24 @@ &i2c6 {
 	status = "okay";
 };
 
+&i2srx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2srx_pins>;
+	status = "okay";
+};
+
+&i2stx0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mclk_ext_pins>;
+	status = "okay";
+};
+
+&i2stx1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2stx1_pins>;
+	status = "okay";
+};
+
 &mmc0 {
 	max-frequency = <100000000>;
 	bus-width = <8>;
@@ -337,6 +355,46 @@ GPOEN_SYS_I2C6_DATA,
 		};
 	};
 
+	i2srx_pins: i2srx-0 {
+		clk-sd-pins {
+			pinmux = <GPIOMUX(38, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_BCLK)>,
+				 <GPIOMUX(63, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_LRCK)>,
+				 <GPIOMUX(38, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2STX1_BCLK)>,
+				 <GPIOMUX(63, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2STX1_LRCK)>,
+				 <GPIOMUX(61, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_I2SRX_SDIN0)>;
+			input-enable;
+		};
+	};
+
+	i2stx1_pins: i2stx1-0 {
+		sd-pins {
+			pinmux = <GPIOMUX(44, GPOUT_SYS_I2STX1_SDO0,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	mclk_ext_pins: mclk-ext-0 {
+		mclk-ext-pins {
+			pinmux = <GPIOMUX(4, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_MCLK_EXT)>;
+			input-enable;
+		};
+	};
+
 	mmc0_pins: mmc0-0 {
 		 rst-pins {
 			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
arch/riscv/boot/dts/starfive/jh7110.dtsi +58 -0
index e85464c328d0..621b68c02ea8 100644
@@ -512,6 +512,30 @@ tdm: tdm@10090000 {
 			status = "disabled";
 		};
 
+		i2srx: i2s@100e0000 {
+			compatible = "starfive,jh7110-i2srx";
+			reg = <0x0 0x100e0000 0x0 0x1000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2SRX_BCLK_MST>,
+				 <&syscrg JH7110_SYSCLK_I2SRX_APB>,
+				 <&syscrg JH7110_SYSCLK_MCLK>,
+				 <&syscrg JH7110_SYSCLK_MCLK_INNER>,
+				 <&mclk_ext>,
+				 <&syscrg JH7110_SYSCLK_I2SRX_BCLK>,
+				 <&syscrg JH7110_SYSCLK_I2SRX_LRCK>,
+				 <&i2srx_bclk_ext>,
+				 <&i2srx_lrck_ext>;
+			clock-names = "i2sclk", "apb", "mclk",
+				      "mclk_inner", "mclk_ext", "bclk",
+				      "lrck", "bclk_ext", "lrck_ext";
+			resets = <&syscrg JH7110_SYSRST_I2SRX_APB>,
+				 <&syscrg JH7110_SYSRST_I2SRX_BCLK>;
+			dmas = <0>, <&dma 24>;
+			dma-names = "tx", "rx";
+			starfive,syscon = <&sys_syscon 0x18 0x2>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
 		usb0: usb@10100000 {
 			compatible = "starfive,jh7110-usb";
 			ranges = <0x0 0x0 0x10100000 0x100000>;
@@ -736,6 +760,47 @@ spi6: spi@120a0000 {
 			status = "disabled";
 		};
 
+		i2stx0: i2s@120b0000 {
+			compatible = "starfive,jh7110-i2stx0";
+			reg = <0x0 0x120b0000 0x0 0x1000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2STX0_BCLK_MST>,
+				 <&syscrg JH7110_SYSCLK_I2STX0_APB>,
+				 <&syscrg JH7110_SYSCLK_MCLK>,
+				 <&syscrg JH7110_SYSCLK_MCLK_INNER>,
+				 <&mclk_ext>;
+			clock-names = "i2sclk", "apb", "mclk",
+				      "mclk_inner","mclk_ext";
+			resets = <&syscrg JH7110_SYSRST_I2STX0_APB>,
+				 <&syscrg JH7110_SYSRST_I2STX0_BCLK>;
+			dmas = <&dma 47>;
+			dma-names = "tx";
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		i2stx1: i2s@120c0000 {
+			compatible = "starfive,jh7110-i2stx1";
+			reg = <0x0 0x120c0000 0x0 0x1000>;
+			clocks = <&syscrg JH7110_SYSCLK_I2STX1_BCLK_MST>,
+				 <&syscrg JH7110_SYSCLK_I2STX1_APB>,
+				 <&syscrg JH7110_SYSCLK_MCLK>,
+				 <&syscrg JH7110_SYSCLK_MCLK_INNER>,
+				 <&mclk_ext>,
+				 <&syscrg JH7110_SYSCLK_I2STX1_BCLK>,
+				 <&syscrg JH7110_SYSCLK_I2STX1_LRCK>,
+				 <&i2stx_bclk_ext>,
+				 <&i2stx_lrck_ext>;
+			clock-names = "i2sclk", "apb", "mclk",
+				      "mclk_inner", "mclk_ext", "bclk",
+				      "lrck", "bclk_ext", "lrck_ext";
+			resets = <&syscrg JH7110_SYSRST_I2STX1_APB>,

arch/riscv/boot/dts/starfive/jh7110.dtsi spi6: spi@120a0000 { · line 806

Quoted 10 lines
arch/riscv/boot/dts/starfive/jh7110.dtsi +7 -0
+				 <&syscrg JH7110_SYSRST_I2STX1_BCLK>;
+			dmas = <&dma 48>;
+			dma-names = "tx";
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
 		sfctemp: temperature-sensor@120e0000 {
 			compatible = "starfive,jh7110-temp";
 			reg = <0x0 0x120e0000 0x0 0x10000>;

Thanks!

maintainer
#10 lore raw

Re: (subset) [PATCH v2 0/5] Add I2S support for the StarFive JH7110 SoC

In reply to Xingyu Wu
Quoted 14 lines · Xingyu Wu

This patch series adds I2S support for the StarFive JH7110 RISC-V SoC based on Designware I2S controller. There has three I2S channels (RX/TX0/TX1) on the JH7110 SoC, one of which is for record(RX) and two for playback(TX).

The first patch adds support for the StarFive JH7110 SoC in the Designware I2S bindings.
The second patch adds the ops to get data from platform bus in the I2S driver.
The third patch adds support for the StarFive JH7110 SoC in the Designware I2S driver.
The fourth patch fixes the name of I2STX1 pinmux.
The last patch adds device node of I2S RX/TX0/TX1 in JH7110 dts.

Quoted 1 line

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/5] ASoC: dt-bindings: snps,designware-i2s: Add StarFive JH7110 SoC support

      commit: 206110c74c4af6772916acacae5f28993085bf18
[2/5] ASoC: dwc: Use ops to get platform data
      commit: d6d6c513f5d2d14651336fb4e30f097822b46f29
[3/5] ASoC: dwc: i2s: Add StarFive JH7110 SoC support
      commit: 52ea7c0543f8a39da8a6fc17a5ab36b7b58d5431

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv

maintainer Applied
#11 lore raw

Re: (subset) [PATCH v2 0/5] Add I2S support for the StarFive JH7110 SoC

In reply to Xingyu Wu

From: Conor Dooley <[email protected]>

Quoted 14 lines · Xingyu Wu

This patch series adds I2S support for the StarFive JH7110 RISC-V SoC based on Designware I2S controller. There has three I2S channels (RX/TX0/TX1) on the JH7110 SoC, one of which is for record(RX) and two for playback(TX).

The first patch adds support for the StarFive JH7110 SoC in the Designware I2S bindings.
The second patch adds the ops to get data from platform bus in the I2S driver.
The third patch adds support for the StarFive JH7110 SoC in the Designware I2S driver.
The fourth patch fixes the name of I2STX1 pinmux.
The last patch adds device node of I2S RX/TX0/TX1 in JH7110 dts.

Quoted 1 line

[...]

Applied to riscv-dt-for-next, thanks!

[4/5] riscv: dts: starfive: pinfunc: Fix the pins name of I2STX1

      https://git.kernel.org/conor/c/4e1abae5688a
[5/5] riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1
      https://git.kernel.org/conor/c/92cfc35838b2

Thanks,
Conor.