Introduce model for IBM's FSI
Subsystems (2)
PATCH v4 2/10 hw/fsi: Introduce IBM's scratchpad
In reply to Ninad PalsuleThis is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS device is embeded inside the scratchpad. The scratchpad provides a non-functional registers. There is a 1-1 relation between scratchpad and LBUS devices. Each LBUS device has 1K memory mapped in the LBUS.
---
v2:
- Incorporated Joel's review comments.
--- hw/fsi/Kconfig | 4 ++ hw/fsi/engine-scratchpad.c | 100 +++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 + include/hw/fsi/engine-scratchpad.h | 33 ++++++++++ 4 files changed, 138 insertions(+) create mode 100644 hw/fsi/engine-scratchpad.c create mode 100644 include/hw/fsi/engine-scratchpad.h
hw/fsi/Kconfig +4 -0
@@ -1,2 +1,6 @@ +config SCRATCHPAD + bool + select LBUS + config LBUS bool
hw/fsi/engine-scratchpad.c new file +100 -0
100 lines not on this page · raw message
hw/fsi/meson.build +1 -0
@@ -1 +1,2 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c'))
include/hw/fsi/engine-scratchpad.h new file +33 -0
@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engne +*/ +#ifndef FSI_ENGINE_SCRATCHPAD_H +#define FSI_ENGINE_SCRATCHPAD_H + +#include "qemu/bitops.h" + +#include "hw/fsi/lbus.h" + +#define ENGINE_CONFIG_NEXT BE_BIT(0) +#define ENGINE_CONFIG_VPD BE_BIT(1) +#define ENGINE_CONFIG_SLOTS BE_GENMASK(8, 15) +#define ENGINE_CONFIG_VERSION BE_GENMASK(16, 19) +#define ENGINE_CONFIG_TYPE BE_GENMASK(20, 27) +#define ENGINE_CONFIG_TYPE_PEEK (0x02 << 4) +#define ENGINE_CONFIG_TYPE_FSI (0x03 << 4) +#define ENGINE_CONFIG_TYPE_SCRATCHPAD (0x06 << 4) +#define ENGINE_CONFIG_CRC BE_GENMASK(28, 31) + +#define TYPE_SCRATCHPAD "scratchpad" +#define SCRATCHPAD (obj) OBJECT_CHECK(ScratchPad, (obj), TYPE_SCRATCHPAD) + +typedef struct ScratchPad { +LBusDevice parent; + +uint32_t reg; +}ScratchPad ; + +#endif /* FSI_ENGINE_SCRATCHPAD_H */
Signature · 1 line
2.39.2
PATCH v4 10/10 hw/fsi: Update MAINTAINER list
In reply to Ninad PalsuleAdded maintainer for IBM FSI model
---
V4:
- Added separate commit for MAINTAINER change.
--- MAINTAINERS | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)
MAINTAINERS +22 -0
@@ -3395,6 +3395,28 @@ F: tests/qtest/adm1272-test.c F: tests/qtest/max34451-test.c F: tests/qtest/isl_pmbus_vr-test.c +FSI +M: Ninad Palsule <[email protected]> +S: Maintained +F: hw/fsi/aspeed-apb2opb.c +F: hw/fsi/cfam.c +F: hw/fsi/fsi.c +F: hw/fsi/fsi-slave.c +F: hw/fsi/opb.c +F: hw/fsi/engine-scratchpad.c +F: hw/fsi/fsi-master.c +F: hw/fsi/lbus.c +F: include/hw/fsi/aspeed-apb2opb.h +F: include/hw/fsi/cfam.h +F: include/hw/fsi/fsi.h +F: include/hw/fsi/fsi-slave.h +F: include/hw/fsi/opb.h +F: include/hw/fsi/engine-scratchpad.h +F: include/hw/fsi/fsi-master.h +F: include/hw/fsi/lbus.h +F: docs/specs/fsi.rst +F: tests/qtest/fsi-test.c + Firmware schema specifications M: Philippe Mathieu-Daudé <[email protected]> R: Daniel P. Berrange <[email protected]>
Signature · 1 line
2.39.2
PATCH v4 8/10 hw/fsi: Added qtest
In reply to Ninad PalsuleAdded basic qtests for FSI model.
---
v3:
- Added new qtest as per Cedric's comment.
V4:
- Remove MAINTAINER and documentation changes from this commit
--- tests/qtest/fsi-test.c | 210 ++++++++++++++++++++++++++++++++++++++++ tests/qtest/meson.build | 2 + 2 files changed, 212 insertions(+) create mode 100644 tests/qtest/fsi-test.c
tests/qtest/fsi-test.c new file +210 -0
@@ -0,0 +1,210 @@ +/* +* QTest testcases for IBM's Flexible Service Interface (FSI) +* +* Copyright (c) 2023 IBM Corporation +* +* Authors: +* Ninad Palsule <[email protected]> +* +* This work is licensed under the terms of the GNU GPL, version 2 or later. +* See the COPYING file in the top-level directory. +*/ + +#include "qemu/osdep.h" +#include <glib/gstdio.h> + +#include "qemu/module.h" +#include "libqtest-single.h" + +/* Registers from ast2600 specifications */ +#define ASPEED_FSI_ENGINER_TRIGGER 0x04 +#define ASPEED_FSI_OPB0_BUS_SELECT 0x10 +#define ASPEED_FSI_OPB1_BUS_SELECT 0x28 +#define ASPEED_FSI_OPB0_RW_DIRECTION 0x14 +#define ASPEED_FSI_OPB1_RW_DIRECTION 0x2c +#define ASPEED_FSI_OPB0_XFER_SIZE 0x18 +#define ASPEED_FSI_OPB1_XFER_SIZE 0x30 +#define ASPEED_FSI_OPB0_BUS_ADDR 0x1c +#define ASPEED_FSI_OPB1_BUS_ADDR 0x34 +#define ASPEED_FSI_INTRRUPT_CLEAR 0x40 +#define ASPEED_FSI_INTRRUPT_STATUS 0x48 +#define ASPEED_FSI_OPB0_BUS_STATUS 0x80 +#define ASPEED_FSI_OPB1_BUS_STATUS 0x8c +#define ASPEED_FSI_OPB0_READ_DATA 0x84 +#define ASPEED_FSI_OPB1_READ_DATA 0x90 + +/* +* FSI Base addresses from the ast2600 specifications. +*/ +#define AST2600_OPB_FSI0_BASE_ADDR 0x1e79b000 +#define AST2600_OPB_FSI1_BASE_ADDR 0x1e79b100 + +static uint32_t aspeed_fsi_base_addr; + +static uint32_t aspeed_fsi_readl (QTestState *s,uint32_t reg) +{ +return qtest_readl (s, aspeed_fsi_base_addr + reg); +} + +static void aspeed_fsi_writel (QTestState *s,uint32_t reg,uint32_t val) +{ +qtest_writel (s, aspeed_fsi_base_addr + reg, val); +} + +/* Setup base address and select register */ +static void test_fsi_setup (QTestState *s,uint32_t base_addr) +{ +uint32_t curval; + +/* Set the base select register */ +if (base_addr ==AST2600_OPB_FSI0_BASE_ADDR ) { + aspeed_fsi_base_addr = base_addr; + +/* Unselect FSI1 */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB1_BUS_SELECT ,0x0 ); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB1_BUS_SELECT ); + g_assert_cmpuint(curval, ==, 0x0); + +/* Select FSI0 */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB0_BUS_SELECT ,0x1 ); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB0_BUS_SELECT ); + g_assert_cmpuint(curval, ==, 0x1); + }else if (base_addr ==AST2600_OPB_FSI1_BASE_ADDR ) { + aspeed_fsi_base_addr = base_addr; + +/* Unselect FSI0 */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB0_BUS_SELECT ,0x0 ); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB0_BUS_SELECT ); + g_assert_cmpuint(curval, ==, 0x0); + +/* Select FSI1 */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB1_BUS_SELECT ,0x1 ); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB1_BUS_SELECT ); + g_assert_cmpuint(curval, ==, 0x1); + }else { +g_assert_not_reached (); + } +} + +static void test_fsi_reg_change (QTestState *s,uint32_t reg,uint32_t newval) +{ +uint32_t base; +uint32_t curval; + + base =aspeed_fsi_readl (s, reg); +aspeed_fsi_writel (s, reg, newval); + curval =aspeed_fsi_readl (s, reg); + g_assert_cmpuint(curval, ==, newval); +aspeed_fsi_writel (s, reg, base); + curval =aspeed_fsi_readl (s, reg); + g_assert_cmpuint(curval, ==, base); +} + +static void test_fsi0_master_regs (const void *data) +{ +QTestState *s = (QTestState *)data; + +test_fsi_setup (s,AST2600_OPB_FSI0_BASE_ADDR ); + +test_fsi_reg_change (s,ASPEED_FSI_OPB0_RW_DIRECTION ,0xF3F4F514 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB0_XFER_SIZE ,0xF3F4F518 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB0_BUS_ADDR ,0xF3F4F51c ); +test_fsi_reg_change (s,ASPEED_FSI_INTRRUPT_CLEAR ,0xF3F4F540 ); +test_fsi_reg_change (s,ASPEED_FSI_INTRRUPT_STATUS ,0xF3F4F548 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB0_BUS_STATUS ,0xF3F4F580 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB0_READ_DATA ,0xF3F4F584 ); +} + +static void test_fsi1_master_regs (const void *data) +{ +QTestState *s = (QTestState *)data; + +test_fsi_setup (s,AST2600_OPB_FSI1_BASE_ADDR ); + +test_fsi_reg_change (s,ASPEED_FSI_OPB1_RW_DIRECTION ,0xF3F4F514 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB1_XFER_SIZE ,0xF3F4F518 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB1_BUS_ADDR ,0xF3F4F51c ); +test_fsi_reg_change (s,ASPEED_FSI_INTRRUPT_CLEAR ,0xF3F4F540 ); +test_fsi_reg_change (s,ASPEED_FSI_INTRRUPT_STATUS ,0xF3F4F548 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB1_BUS_STATUS ,0xF3F4F580 ); +test_fsi_reg_change (s,ASPEED_FSI_OPB1_READ_DATA ,0xF3F4F584 ); +} + +static void test_fsi0_getcfam_addr0 (const void *data) +{ +QTestState *s = (QTestState *)data; +uint32_t curval; + +test_fsi_setup (s,AST2600_OPB_FSI0_BASE_ADDR ); + +/* Master access direction read */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB0_RW_DIRECTION ,0x1 ); +/* word */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB0_XFER_SIZE ,0x3 ); +/* Address */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB0_BUS_ADDR ,0xa0000000 ); +aspeed_fsi_writel (s,ASPEED_FSI_INTRRUPT_CLEAR ,0x1 ); +aspeed_fsi_writel (s,ASPEED_FSI_ENGINER_TRIGGER ,0x1 ); + + curval =aspeed_fsi_readl (s,ASPEED_FSI_INTRRUPT_STATUS ); + g_assert_cmpuint(curval, ==, 0x10000); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB0_BUS_STATUS ); + g_assert_cmpuint(curval, ==, 0x0); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB0_READ_DATA ); + g_assert_cmpuint(curval, ==, 0x152d02c0); +} + +static void test_fsi1_getcfam_addr0 (const void *data) +{ +QTestState *s = (QTestState *)data; +uint32_t curval; + +test_fsi_setup (s,AST2600_OPB_FSI1_BASE_ADDR ); + +/* Master access direction read */ +aspeed_fsi_writel (s,ASPEED_FSI_OPB1_RW_DIRECTION ,0x1 ); + +aspeed_fsi_writel (s,ASPEED_FSI_OPB1_XFER_SIZE ,0x3 ); +aspeed_fsi_writel (s,ASPEED_FSI_OPB1_BUS_ADDR ,0xa0000000 ); +aspeed_fsi_writel (s,ASPEED_FSI_INTRRUPT_CLEAR ,0x1 ); +aspeed_fsi_writel (s,ASPEED_FSI_ENGINER_TRIGGER ,0x1 ); + + curval =aspeed_fsi_readl (s,ASPEED_FSI_INTRRUPT_STATUS ); + g_assert_cmpuint(curval, ==, 0x20000); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB1_BUS_STATUS ); + g_assert_cmpuint(curval, ==, 0x0); + curval =aspeed_fsi_readl (s,ASPEED_FSI_OPB1_READ_DATA ); + g_assert_cmpuint(curval, ==, 0x152d02c0); +} + +int main (int argc,char **argv) +{ +int ret =-1 ; +QTestState *s; + +g_test_init (&argc, &argv,NULL ); + + s =qtest_init ("-machine ast2600-evb " ); +if (s ==NULL ) { +return -ENOMEM ; + } + +/* Tests for OPB/FSI0 */ +qtest_add_data_func ("/fsi-test/test_fsi0_master_regs" , s, + test_fsi0_master_regs); + +qtest_add_data_func ("/fsi-test/test_fsi0_getcfam_addr0" , s, + test_fsi0_getcfam_addr0); + +/* Tests for OPB/FSI1 */ +qtest_add_data_func ("/fsi-test/test_fsi1_master_regs" , s, + test_fsi1_master_regs); + +qtest_add_data_func ("/fsi-test/test_fsi1_getcfam_addr0" , s, + test_fsi1_getcfam_addr0); + + ret =g_test_run (); +qtest_quit (s); + +return ret; +}
tests/qtest/meson.build +2 -0
@@ -207,6 +207,7 @@ qtests_arm = \ (config_all_devices.has_key('CONFIG_TPM_TIS_I2C') ? ['tpm-tis-i2c-test'] : []) + \ (config_all_devices.has_key('CONFIG_VEXPRESS') ? ['test-arm-mptimer'] : []) + \ (config_all_devices.has_key('CONFIG_MICROBIT') ? ['microbit-test'] : []) + \ + (config_all_devices.has_key('CONFIG_FSI_APB2OPB_ASPEED') ? ['fsi-test'] : []) + \ ['arm-cpu-features', 'boot-serial-test']
@@ -318,6 +319,7 @@ qtests = { 'tpm-tis-device-test': [io, tpmemu_files, 'tpm-tis-util.c'], 'vmgenid-test': files('boot-sector.c', 'acpi-utils.c'), 'netdev-socket': files('netdev-socket.c', '../unit/socket-helpers.c'), + 'fsi-test': files('fsi-test.c'), } if vnc.found()
Signature · 1 line
2.39.2
PATCH v4 3/10 hw/fsi: Introduce IBM's cfam,fsi-slave
In reply to Ninad PalsuleThis is a part of patchset where IBM's Flexible Service Interface is introduced.
The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on busses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
---
v2:
- Incorporated Joel's review comments.
v3:
- Incorporated Thomas Huth's review comments.
--- hw/fsi/Kconfig | 9 ++ hw/fsi/cfam.c | 238 +++++++++++++++++++++++++++++++++++++ hw/fsi/fsi-slave.c | 109 +++++++++++++++++ hw/fsi/meson.build | 2 + hw/fsi/trace-events | 5 + include/hw/fsi/cfam.h | 61 ++++++++++ include/hw/fsi/fsi-slave.h | 29 +++++ 7 files changed, 453 insertions(+) create mode 100644 hw/fsi/cfam.c create mode 100644 hw/fsi/fsi-slave.c create mode 100644 hw/fsi/trace-events create mode 100644 include/hw/fsi/cfam.h create mode 100644 include/hw/fsi/fsi-slave.h
hw/fsi/Kconfig +9 -0
@@ -1,3 +1,12 @@ +config CFAM + bool + select FSI + select SCRATCHPAD + select LBUS + +config FSI + bool + config SCRATCHPAD bool select LBUS
hw/fsi/cfam.c new file +238 -0
238 lines not on this page · raw message
hw/fsi/fsi-slave.c new file +109 -0
109 lines not on this page · raw message
hw/fsi/meson.build +2 -0
@@ -1,2 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c'))
hw/fsi/trace-events new file +5 -0
@@ -0,0 +1,5 @@ +cfam_config_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +cfam_config_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 + +cfam_unimplemented_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +cfam_unimplemented_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64
include/hw/fsi/cfam.h new file +61 -0
61 lines not on this page · raw message
include/hw/fsi/fsi-slave.h new file +29 -0
@@ -0,0 +1,29 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface slave +*/ +#ifndef FSI_FSI_SLAVE_H +#define FSI_FSI_SLAVE_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" + +#include "hw/fsi/lbus.h" + +#include <stdint.h> + +#define TYPE_FSI_SLAVE "fsi.slave" +#define FSI_SLAVE (obj) \ + OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +#define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1) + +typedef struct FSISlaveState { +DeviceState parent; + +MemoryRegion iomem; +uint32_t regs[FSI_SLAVE_CONTROL_NR_REGS ]; +}FSISlaveState ; + +#endif /* FSI_FSI_H */
Signature · 1 line
2.39.2
v4 cover Introduce model for IBM's FSI
Hello,
Please review the patch-set version 4.
I have incorporated review comments from Cedric and Thomas.
Ninad Palsule (10):
hw/fsi: Introduce IBM's Local bus
hw/fsi: Introduce IBM's scratchpad
hw/fsi: Introduce IBM's cfam,fsi-slave
hw/fsi: Introduce IBM's FSI
hw/fsi: IBM's On-chip Peripheral Bus
hw/fsi: Aspeed APB2OPB interface
hw/arm: Hook up FSI module in AST2600
hw/fsi: Added qtest
hw/fsi: Added FSI documentation
hw/fsi: Update MAINTAINER list
MAINTAINERS | 22 ++ docs/specs/fsi.rst | 141 ++++++++++++ hw/Kconfig | 1 + hw/arm/Kconfig | 1 + hw/arm/aspeed_ast2600.c | 19 ++ hw/fsi/Kconfig | 23 ++ hw/fsi/aspeed-apb2opb.c | 352 +++++++++++++++++++++++++++++ hw/fsi/cfam.c | 239 ++++++++++++++++++++ hw/fsi/engine-scratchpad.c | 100 ++++++++ hw/fsi/fsi-master.c | 201 ++++++++++++++++ hw/fsi/fsi-slave.c | 109 +++++++++ hw/fsi/fsi.c | 54 +++++ hw/fsi/lbus.c | 94 ++++++++ hw/fsi/meson.build | 6 + hw/fsi/opb.c | 194 ++++++++++++++++ hw/fsi/trace-events | 6 + hw/fsi/trace.h | 1 + hw/meson.build | 1 + include/hw/arm/aspeed_soc.h | 4 + include/hw/fsi/aspeed-apb2opb.h | 33 +++ include/hw/fsi/cfam.h | 61 +++++ include/hw/fsi/engine-scratchpad.h | 33 +++ include/hw/fsi/fsi-master.h | 30 +++ include/hw/fsi/fsi-slave.h | 29 +++ include/hw/fsi/fsi.h | 31 +++ include/hw/fsi/lbus.h | 48 ++++ include/hw/fsi/opb.h | 43 ++++ include/qemu/bitops.h | 6 + meson.build | 1 + tests/qtest/fsi-test.c | 210 +++++++++++++++++ tests/qtest/meson.build | 2 + 31 files changed, 2095 insertions(+) create mode 100644 docs/specs/fsi.rst create mode 100644 hw/fsi/Kconfig create mode 100644 hw/fsi/aspeed-apb2opb.c create mode 100644 hw/fsi/cfam.c create mode 100644 hw/fsi/engine-scratchpad.c create mode 100644 hw/fsi/fsi-master.c create mode 100644 hw/fsi/fsi-slave.c create mode 100644 hw/fsi/fsi.c create mode 100644 hw/fsi/lbus.c create mode 100644 hw/fsi/meson.build create mode 100644 hw/fsi/opb.c create mode 100644 hw/fsi/trace-events create mode 100644 hw/fsi/trace.h create mode 100644 include/hw/fsi/aspeed-apb2opb.h create mode 100644 include/hw/fsi/cfam.h create mode 100644 include/hw/fsi/engine-scratchpad.h create mode 100644 include/hw/fsi/fsi-master.h create mode 100644 include/hw/fsi/fsi-slave.h create mode 100644 include/hw/fsi/fsi.h create mode 100644 include/hw/fsi/lbus.h create mode 100644 include/hw/fsi/opb.h create mode 100644 tests/qtest/fsi-test.c
Signature · 1 line
2.39.2
PATCH v4 4/10 hw/fsi: Introduce IBM's FSI
This is a part of patchset where IBM's Flexible Service Interface is introduced.
This commit models the FSI bus. CFAM is hanging out of FSI bus. The bus is model such a way that it is embeded inside the FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
---
v2:
- Incorporated review comments by Joel
--- hw/fsi/cfam.c | 3 +- hw/fsi/fsi-master.c | 203 ++++++++++++++++++++++++++++++++++++ hw/fsi/fsi.c | 54 ++++++++++ hw/fsi/meson.build | 2 +- include/hw/fsi/cfam.h | 8 +- include/hw/fsi/fsi-master.h | 30 ++++++ include/hw/fsi/fsi-slave.h | 4 +- include/hw/fsi/fsi.h | 31 ++++++ 8 files changed, 327 insertions(+), 8 deletions(-) create mode 100644 hw/fsi/fsi-master.c create mode 100644 hw/fsi/fsi.c create mode 100644 include/hw/fsi/fsi-master.h create mode 100644 include/hw/fsi/fsi.h
hw/fsi/cfam.c +2 -1
@@ -7,12 +7,13 @@#include "qemu/osdep.h" +#include "qemu/bitops.h" #include "qapi/error.h" #include "qemu/log.h" #include "trace.h" -#include "hw/fsi/bits.h" #include "hw/fsi/cfam.h" +#include "hw/fsi/fsi.h" #include "hw/fsi/engine-scratchpad.h" #include "hw/qdev-properties.h"
hw/fsi/fsi-master.c new file +203 -0
203 lines not on this page · raw message
hw/fsi/fsi.c new file +54 -0
54 lines not on this page · raw message
hw/fsi/meson.build +1 -1
@@ -1,4 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) -system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c')) +system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c'))
include/hw/fsi/cfam.h +4 -4
@@ -12,14 +12,14 @@#include "hw/fsi/fsi-slave.h" #include "hw/fsi/lbus.h" -#define TYPE_FSI_BUS "fsi.bus" -#define TYPE_CFAM "cfam"#define CFAM (obj) OBJECT_CHECK(CFAMState, (obj), TYPE_CFAM)#define CFAM_NR_REGS ((0x2e0 >> 2) + 1)#define TYPE_CFAM_CONFIG "cfam.config" +OBJECT_DECLARE_SIMPLE_TYPE(CFAMConfig, CFAM_CONFIG) +#define CFAM_CONFIG (obj) \ OBJECT_CHECK(CFAMConfig, (obj), TYPE_CFAM_CONFIG)/* P9-ism */
@@ -35,8 +35,8 @@ typedef struct CFAMConfig { } CFAMConfig;#define TYPE_CFAM_PEEK "cfam.peek" -#define CFAM_PEEK (obj) \ - OBJECT_CHECK(CFAMPeek, (obj), TYPE_CFAM_PEEK) +OBJECT_DECLARE_SIMPLE_TYPE(CFAMPeek, CFAM_PEEK) +#define CFAM_PEEK_NR_REGS ((0x130 >> 2) + 1) typedef struct CFAMPeek {
include/hw/fsi/fsi-master.h new file +30 -0
@@ -0,0 +1,30 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2019 IBM Corp. +* +* IBM Flexible Service Interface Master +*/ +#ifndef FSI_FSI_MASTER_H +#define FSI_FSI_MASTER_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" +#include "hw/fsi/fsi.h" + +#define TYPE_FSI_MASTER "fsi.master" +OBJECT_DECLARE_SIMPLE_TYPE(FSIMasterState, FSI_MASTER) + +#define FSI_MASTER_NR_REGS ((0x2e0 >> 2) + 1) + +typedef struct FSIMasterState { +DeviceState parent; +MemoryRegion iomem; +MemoryRegion opb2fsi; + +FSIBus bus; + +uint32_t regs[FSI_MASTER_NR_REGS ]; +}FSIMasterState ; + + +#endif /* FSI_FSI_H */
include/hw/fsi/fsi-slave.h +2 -2
@@ -15,8 +15,8 @@#include <stdint.h> #define TYPE_FSI_SLAVE "fsi.slave" -#define FSI_SLAVE (obj) \ - OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +OBJECT_DECLARE_SIMPLE_TYPE(FSISlaveState, FSI_SLAVE) +#define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1) typedef struct FSISlaveState {
include/hw/fsi/fsi.h new file +31 -0
@@ -0,0 +1,31 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface +*/ +#ifndef FSI_FSI_H +#define FSI_FSI_H + +#include "hw/qdev-core.h" + +/* +* TODO: Maybe unwind this dependency with const links? Store a +* pointer in FSIBus? +*/ +#include "hw/fsi/cfam.h" + +#define TYPE_FSI_BUS "fsi.bus" +OBJECT_DECLARE_SIMPLE_TYPE (FSIBus,FSI_BUS ) + +/* TODO: Figure out what's best with a point-to-point bus */ +typedef struct FSISlaveState FSISlaveState ; + +typedef struct FSIBus { +BusState bus; + +/* XXX: It's point-to-point, just instantiate the slave directly for now */ +CFAMState slave; +}FSIBus ; + +#endif
Signature · 1 line
2.39.2
PATCH v4 7/10 hw/arm: Hook up FSI module in AST2600
In reply to Ninad PalsuleThis patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service processor access to the internal buses of a host POWER processor to perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage, including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on buses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for a CFAM to be simultaneously driven from multiple FSI links. The modeling is not so complete; it's assumed that each CFAM is attached to a single FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This is not necessary to get FSI off the ground thanks to the mapping of the CFAM address space onto the OPB address space - the models follow this directly and map the CFAM memory region into the OPB's memory region. Future work includes supporting more advanced accesses that drive the FSI master directly rather than indirectly via the CFAM mapping, which will require implementing the FSI state machine and methods for each of the FSI symbols on the slave. Further down the track we can also look at supporting the bitbanged SoftFSI drivers in Linux by extending the FSI slave model to resolve sequences of GPIO IRQs into FSI symbols, and calling the associated symbol method on the slave to map the access onto the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.
root@p10bmc:~# pdbg -a getcfam 0x0
p0: 0x0 = 0xc0022d15--- hw/arm/aspeed_ast2600.c | 19 +++++++++++++++++++ include/hw/arm/aspeed_soc.h | 4 ++++ 2 files changed, 23 insertions(+)
hw/arm/aspeed_ast2600.c +19 -0
@@ -75,6 +75,8 @@ static const hwaddr aspeed_soc_ast2600_memmap[] = { [ASPEED_DEV_UART12] = 0x1E790600, [ASPEED_DEV_UART13] = 0x1E790700, [ASPEED_DEV_VUART] = 0x1E787000, + [ASPEED_DEV_FSI1] = 0x1E79B000, + [ASPEED_DEV_FSI2] = 0x1E79B100, [ASPEED_DEV_I3C] = 0x1E7A0000, [ASPEED_DEV_SDRAM] = 0x80000000, };
@@ -132,6 +134,8 @@ static const int aspeed_soc_ast2600_irqmap[] = { [ASPEED_DEV_ETH4] = 33, [ASPEED_DEV_KCS] = 138, /* 138 -> 142 */ [ASPEED_DEV_DP] = 62, + [ASPEED_DEV_FSI1] = 100, + [ASPEED_DEV_FSI2] = 101, [ASPEED_DEV_I3C] = 102, /* 102 -> 107 */ };
@@ -262,6 +266,10 @@ static void aspeed_soc_ast2600_init(Object *obj)object_initialize_child (obj,"emmc-boot-controller" , &s->emmc_boot_controller,TYPE_UNIMPLEMENTED_DEVICE ); + +for (i =0 ; i <ASPEED_FSI_NUM ; i++) { +object_initialize_child (obj,"fsi[*]" , &s->fsi[i],TYPE_ASPEED_APB2OPB ); + } }/*
@@ -622,6 +630,17 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)return ; }aspeed_mmio_map (s,SYS_BUS_DEVICE (&s->sbc),0 , sc->memmap[ASPEED_DEV_SBC ]); + +/* FSI */ +for (i =0 ; i <ASPEED_FSI_NUM ; i++) { +if (!sysbus_realize (SYS_BUS_DEVICE (&s->fsi[i]), errp)) { +return ; + } +aspeed_mmio_map (s,SYS_BUS_DEVICE (&s->fsi[i]),0 , + sc->memmap[ASPEED_DEV_FSI1 + i]); +sysbus_connect_irq (SYS_BUS_DEVICE (&s->fsi[i]),0 , +aspeed_soc_get_irq (s,ASPEED_DEV_FSI1 + i)); + } }static void aspeed_soc_ast2600_class_init (ObjectClass *oc,void *data)
include/hw/arm/aspeed_soc.h +4 -0
@@ -36,6 +36,7 @@#include "hw/misc/aspeed_lpc.h" #include "hw/misc/unimp.h" #include "hw/misc/aspeed_peci.h" +#include "hw/fsi/aspeed-apb2opb.h" #include "hw/char/serial.h" #define ASPEED_SPIS_NUM 2
@@ -96,6 +97,7 @@ struct AspeedSoCState {UnimplementedDeviceState udc;UnimplementedDeviceState sgpiom;UnimplementedDeviceState jtag[ASPEED_JTAG_NUM ]; +AspeedAPB2OPBState fsi[2 ]; };#define TYPE_ASPEED_SOC "aspeed-soc"
@@ -191,6 +193,8 @@ enum {ASPEED_DEV_SGPIOM ,ASPEED_DEV_JTAG0 ,ASPEED_DEV_JTAG1 , +ASPEED_DEV_FSI1 , + ASPEED_DEV_FSI2, };#define ASPEED_SOC_SPI_BOOT_ADDR 0x0
Signature · 1 line
2.39.2
PATCH v4 5/10 hw/fsi: IBM's On-chip Peripheral Bus
In reply to Ninad PalsuleThis is a part of patchset where IBM's Flexible Service Interface is introduced.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
---
v2:
- Incorporated review comment by Joel.
--- hw/fsi/Kconfig | 4 + hw/fsi/fsi-master.c | 6 +- hw/fsi/meson.build | 1 + hw/fsi/opb.c | 194 +++++++++++++++++++++++++++++++++++++++++++ include/hw/fsi/opb.h | 43 ++++++++++ 5 files changed, 244 insertions(+), 4 deletions(-) create mode 100644 hw/fsi/opb.c create mode 100644 include/hw/fsi/opb.h
hw/fsi/Kconfig +4 -0
@@ -1,3 +1,7 @@ +config OPB + bool + select CFAM + config CFAM bool select FSI
hw/fsi/fsi-master.c +2 -4
@@ -7,14 +7,12 @@#include "qemu/osdep.h" +#include "qemu/bitops.h" #include "qapi/error.h" -#include "qemu/log.h" -#include "hw/fsi/bits.h" #include "hw/fsi/fsi-master.h" - -#define TYPE_OP_BUS "opb" +#include "hw/fsi/opb.h" #define TO_REG (x) ((x) >> 2)
hw/fsi/meson.build +1 -0
@@ -2,3 +2,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c')) +system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c'))
hw/fsi/opb.c new file +194 -0
194 lines not on this page · raw message
include/hw/fsi/opb.h new file +43 -0
43 lines not on this page · raw message
Signature · 1 line
2.39.2
PATCH v4 9/10 hw/fsi: Added FSI documentation
In reply to Ninad PalsuleDocumentation for IBM FSI model.
---
v4:
- Added separate commit for documentation
--- docs/specs/fsi.rst | 141 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 141 insertions(+) create mode 100644 docs/specs/fsi.rst
docs/specs/fsi.rst new file +141 -0
@@ -0,0 +1,141 @@ +====================================== +IBM's Flexible Service Interface (FSI) +====================================== + +The QEMU FSI emulation implements hardware interfaces between ASPEED SOC, FSI +master/slave and the end engine. + +FSI is a point-to-point two wire interface which is capable of supporting +distances of up to 4 meters. FSI interfaces have been used successfully for +many years in IBM servers to attach IBM Flexible Support Processors(FSP) to +CPUs and IBM ASICs. + +FSI allows a service processor access to the internal buses of a host POWER +processor to perform configuration or debugging. FSI has long existed in POWER +processes and so comes with some baggage, including how it has been integrated +into the ASPEED SoC. + +Working backwards from the POWER processor, the fundamental pieces of interest +for the implementation are: + +1. The Common FRU Access Macro (CFAM), an address space containing various + "engines" that drive accesses on buses internal and external to the POWER + chip. Examples include the SBEFIFO and I2C masters. The engines hang off of + an internal Local Bus (LBUS) which is described by the CFAM configuration + block. + +2. The FSI slave: The slave is the terminal point of the FSI bus for FSI + symbols addressed to it. Slaves can be cascaded off of one another. The + slave's configuration registers appear in address space of the CFAM to + which it is attached. + +3. The FSI master: A controller in the platform service processor (e.g. BMC) + driving CFAM engine accesses into the POWER chip. At the hardware level + FSI is a bit-based protocol supporting synchronous and DMA-driven accesses + of engines in a CFAM. + +4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER + processors. This now makes an appearance in the ASPEED SoC due to tight + integration of the FSI master IP with the OPB, mainly the existence of an + MMIO-mapping of the CFAM address straight onto a sub-region of the OPB + address space. + +5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in the + AST2600. Hardware limitations prevent the OPB from being directly mapped + into APB, so all accesses are indirect through the bridge. + +The LBUS is modelled to maintain the qdev bus hierarchy and to take advantages +of the object model to automatically generate the CFAM configuration block. +The configuration block presents engines in the order they are attached to the +CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the +'config' member of LBusDeviceClass to match the engine's type. + +CFAM designs offer a lot of flexibility, for instance it is possible for a +CFAM to be simultaneously driven from multiple FSI links. The modeling is not +so complete; it's assumed that each CFAM is attached to a single FSI slave (as +a consequence the CFAM subclasses the FSI slave). + +As for FSI, its symbols and wire-protocol are not modelled at all. This is not +necessary to get FSI off the ground thanks to the mapping of the CFAM address +space onto the OPB address space - the models follow this directly and map the +CFAM memory region into the OPB's memory region. + +QEMU files related to FSI interface: + - ``hw/fsi/aspeed-apb2opb.c`` + - ``include/hw/fsi/aspeed-apb2opb.h`` + - ``hw/fsi/opb.c`` + - ``include/hw/fsi/opb.h`` + - ``hw/fsi/fsi.c`` + - ``include/hw/fsi/fsi.h`` + - ``hw/fsi/fsi-master.c`` + - ``include/hw/fsi/fsi-master.h`` + - ``hw/fsi/fsi-slave.c`` + - ``include/hw/fsi/fsi-slave.h`` + - ``hw/fsi/cfam.c`` + - ``include/hw/fsi/cfam.h`` + - ``hw/fsi/engine-scratchpad.c`` + - ``include/hw/fsi/engine-scratchpad.h`` + - ``include/hw/fsi/lbus.h`` + +The following commands start the rainier machine with built-in FSI model. +There are no model specific arguments. + +.. code-block:: console + + qemu-system-arm -M rainier-bmc -nographic \ + -kernel fitImage-linux.bin \ + -dtb aspeed-bmc-ibm-rainier.dtb \ + -initrd obmc-phosphor-initramfs.rootfs.cpio.xz \ + -drive file=obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2 \ + -append "rootwait console=ttyS4,115200n8 root=PARTLABEL=rofs-a" + +The implementation appears as following in the qemu device tree: + +.. code-block:: console + + (qemu) info qtree + bus: main-system-bus + type System + ... + dev: aspeed.apb2opb, id "" + gpio-out "sysbus-irq" 1 + mmio 000000001e79b000/0000000000001000 + bus: opb.1 + type opb + dev: fsi.master, id "" + bus: fsi.bus.1 + type fsi.bus + dev: cfam.config, id "" + dev: cfam, id "" + bus: lbus.1 + type lbus + dev: scratchpad, id "" + address = 0 (0x0) + bus: opb.0 + type opb + dev: fsi.master, id "" + bus: fsi.bus.0 + type fsi.bus + dev: cfam.config, id "" + dev: cfam, id "" + bus: lbus.0 + type lbus + dev: scratchpad, id "" + address = 0 (0x0) + +pdbg is a simple application to allow debugging of the host POWER processors +from the BMC. (see the `pdbg source repository` for more details) + +.. code-block:: console + + root@p10bmc:~# pdbg -a getcfam 0x0 + p0: 0x0 = 0xc0022d15 + +Refer following documents for more details. + +.. _FSI specification: + https://openpowerfoundation.org/specifications/fsi/ + https://wiki.raptorcs.com/w/images/9/97/OpenFSI-spec-20161212.pdf + +.. _pdbg source repository: + https://github.com/open-power/pdbg
Signature · 1 line
2.39.2
PATCH v4 6/10 hw/fsi: Aspeed APB2OPB interface
In reply to Ninad PalsuleThis is a part of patchset where IBM's Flexible Service Interface is introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
---
v2:
- Incorporated review comments by Joel
v3:
- Incorporated review comments by Thomas Huth
v4:
- Compile FSI with ASPEED_SOC only.
--- hw/arm/Kconfig | 1 + hw/fsi/Kconfig | 20 +- hw/fsi/aspeed-apb2opb.c | 352 ++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 9 +- hw/fsi/trace-events | 3 +- hw/fsi/trace.h | 1 + include/hw/fsi/aspeed-apb2opb.h | 33 +++ meson.build | 1 + 8 files changed, 407 insertions(+), 13 deletions(-) create mode 100644 hw/fsi/aspeed-apb2opb.c create mode 100644 hw/fsi/trace.h create mode 100644 include/hw/fsi/aspeed-apb2opb.h
hw/arm/Kconfig +1 -0
@@ -555,6 +555,7 @@ config ASPEED_SOC select LED select PMBUS select MAX31785 + select FSI_APB2OPB_ASPEED config MPS2 bool
hw/fsi/Kconfig +12 -8
@@ -1,19 +1,23 @@ -config OPB +config FSI_APB2OPB_ASPEED bool - select CFAM + select FSI_OPB -config CFAM +config FSI_OPB + bool + select FSI_CFAM + +config FSI_CFAM bool select FSI - select SCRATCHPAD - select LBUS + select FSI_SCRATCHPAD + select FSI_LBUS config FSI bool -config SCRATCHPAD +config FSI_SCRATCHPAD bool - select LBUS + select FSI_LBUS -config LBUS +config FSI_LBUS bool
hw/fsi/aspeed-apb2opb.c new file +352 -0
352 lines not on this page · raw message
hw/fsi/meson.build +5 -4
@@ -1,5 +1,6 @@ -system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) -system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) -system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_FSI_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_FSI_CFAM', if_true: files('cfam.c')) system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c')) -system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_APB2OPB_ASPEED', if_true: files('aspeed-apb2opb.c'))
hw/fsi/trace-events +2 -1
@@ -1,5 +1,6 @@ cfam_config_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" cfam_config_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 - cfam_unimplemented_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" cfam_unimplemented_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 +aspeed_apb2opb_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +aspeed_apb2opb_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64
hw/fsi/trace.h new file +1 -0
@@ -0,0 +1 @@ +#include "trace/trace-hw_fsi.h"
include/hw/fsi/aspeed-apb2opb.h new file +33 -0
@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* ASPEED APB2OPB Bridge +*/ +#ifndef FSI_ASPEED_APB2OPB_H +#define FSI_ASPEED_APB2OPB_H + +#include "hw/sysbus.h" +#include "hw/fsi/opb.h" + +#define TYPE_ASPEED_APB2OPB "aspeed.apb2opb" +OBJECT_DECLARE_SIMPLE_TYPE(AspeedAPB2OPBState, ASPEED_APB2OPB) + +#define ASPEED_APB2OPB_NR_REGS ((0xe8 >> 2) + 1) + +#define ASPEED_FSI_NUM 2 + +typedef struct AspeedAPB2OPBState { +/*< private >*/ +SysBusDevice parent_obj; + +/*< public >*/ +MemoryRegion iomem; + +uint32_t regs[ASPEED_APB2OPB_NR_REGS ]; +qemu_irq irq; + +OPBus opb[ASPEED_FSI_NUM ]; +}AspeedAPB2OPBState ; + +#endif /* FSI_ASPEED_APB2OPB_H */
meson.build +1 -0
@@ -3244,6 +3244,7 @@ if have_system 'hw/char', 'hw/display', 'hw/dma', + 'hw/fsi', 'hw/hyperv', 'hw/i2c', 'hw/i386',
Signature · 1 line
2.39.2
PATCH v4 1/10 hw/fsi: Introduce IBM's Local bus
In reply to Ninad PalsuleThis is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
---
v2:
- Incorporated Joel's review comments.
--- hw/Kconfig | 1 + hw/fsi/Kconfig | 2 + hw/fsi/lbus.c | 94 +++++++++++++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 + hw/meson.build | 1 + include/hw/fsi/lbus.h | 48 ++++++++++++++++++++++ include/qemu/bitops.h | 6 +++ 7 files changed, 153 insertions(+) create mode 100644 hw/fsi/Kconfig create mode 100644 hw/fsi/lbus.c create mode 100644 hw/fsi/meson.build create mode 100644 include/hw/fsi/lbus.h
hw/Kconfig +1 -0
@@ -9,6 +9,7 @@ source core/Kconfig source cxl/Kconfig source display/Kconfig source dma/Kconfig +source fsi/Kconfig source gpio/Kconfig source hyperv/Kconfig source i2c/Kconfig
hw/fsi/Kconfig new file +2 -0
@@ -0,0 +1,2 @@ +config LBUS + bool
hw/fsi/lbus.c new file +94 -0
94 lines not on this page · raw message
hw/fsi/meson.build new file +1 -0
@@ -0,0 +1 @@ +system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c'))
hw/meson.build +1 -0
@@ -43,6 +43,7 @@ subdir('virtio') subdir('watchdog') subdir('xen') subdir('xenpv') +subdir('fsi') subdir('alpha') subdir('arm')
include/hw/fsi/lbus.h new file +48 -0
48 lines not on this page · raw message
include/qemu/bitops.h +6 -0
@@ -618,4 +618,10 @@ static inline uint64_t half_unshuffle64(uint64_t x) return x; } +/* Bitwise operations at the word level. */ +#define BE_BIT (x) BIT(31 - (x)) +#define GENMASK (t, b) \ + (((1ULL << ((t) + 1)) - 1) & ~((1ULL << (b)) - 1)) +#define BE_GENMASK (t, b) GENMASK(BE_BIT(t), BE_BIT(b)) +#endif
Signature · 1 line
2.39.2
Re: [PATCH v4 01/10] hw/fsi: Introduce IBM's Local bus
Quoted 10 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
Quoted 7 lines
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
---
It is nice to have the header files upfront.
orderFile = /path/to/qemu/scripts/git.orderfile
Quoted 52 lines
hw/Kconfig | 1 + hw/fsi/Kconfig | 2 + hw/fsi/lbus.c | 94 +++++++++++++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 + hw/meson.build | 1 + include/hw/fsi/lbus.h | 48 ++++++++++++++++++++++ include/qemu/bitops.h | 6 +++ 7 files changed, 153 insertions(+)create mode 100644 hw/fsi/Kconfig
create mode 100644hw/fsi/lbus.c
create mode 100644 hw/fsi/meson.build
create mode 100644include/hw/fsi/lbus.hhw/Kconfig +1
-0@@ -9,6 +9,7 @@ source core/Kconfig source cxl/Kconfig source display/Kconfig source dma/Kconfig +source fsi/Kconfig source gpio/Kconfig source hyperv/Kconfig source i2c/Kconfighw/fsi/Kconfig new file +2
-0@@ -0,0 +1,2 @@ +config LBUS + boolhw/fsi/lbus.c new file +13
-0@@ -0,0 +1,94 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Local bus where FSI slaves are connected +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/lbus.h"
hw/fsi/lbus.c line 23
Quoted 10 lines
hw/fsi/lbus.c new file +10
-0+ +#include "hw/qdev-properties.h" + +static void lbus_realize (BusState *bus,Error **errp) +{ +LBusNode *node; +LBus *lbus =LBUS (bus); + +memory_region_init (&lbus->mr,OBJECT (lbus),TYPE_LBUS , + (2 *1024 *1024 ) -0x400 );
please use some define
hw/fsi/lbus.c line 34
Quoted 11 lines
hw/fsi/lbus.c new file +11
-0+ + QLIST_FOREACH(node, &lbus->devices, next) { +memory_region_add_subregion (&lbus->mr, node->ldev->address, + &node->ldev->iomem); + } +} + +static void lbus_init (Object *o) +{ +} +
please remove if unused
Quoted 17 lines
hw/fsi/lbus.c new file +17
-0+static void lbus_class_init (ObjectClass *klass,void *data) +{ +BusClass *k =BUS_CLASS (klass); + k->realize = lbus_realize; +} + +static const TypeInfo lbus_info = { + .name =TYPE_LBUS , + .parent =TYPE_BUS , + .instance_init = lbus_init, + .instance_size =sizeof (LBus), + .class_init = lbus_class_init, +}; + +static Property lbus_device_props[] = { +DEFINE_PROP_UINT32 ("address" , LBusDevice, address,0 ), +DEFINE_PROP_END_OF_LIST (),
hw/fsi/lbus.c line 61
Quoted 10 lines
hw/fsi/lbus.c new file +10
-0+}; + +DeviceState *lbus_create_device (LBus *bus,const char *type,uint32_t addr) +{ +DeviceState *dev; +LBusNode *node; + + dev =qdev_new (type); +qdev_prop_set_uint8 (dev,"address" , addr); +qdev_realize_and_unref (dev, &bus->bus, &error_fatal);
BUS(bus) ?
hw/fsi/lbus.c line 66
Quoted 5 lines
hw/fsi/lbus.c new file +5
-0+ +/* Move to post_load */ + node =g_malloc (sizeof (struct LBusNode )); + node->ldev =LBUS_DEVICE (dev); +QLIST_INSERT_HEAD (&bus->devices, node, next);
This list looks useless to me.
Quoted 57 lines
hw/fsi/lbus.c new file +27
-0+return dev; +} + +static void lbus_device_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + + dc->bus_type =TYPE_LBUS ; +device_class_set_props (dc, lbus_device_props); +} + +static const TypeInfo lbus_device_type_info = { + .name =TYPE_LBUS_DEVICE , + .parent =TYPE_DEVICE , + .instance_size =sizeof (LBusDevice), + .abstract = true, + .class_init = lbus_device_class_init, + .class_size =sizeof (LBusDeviceClass), +}; + +static void lbus_register_types (void ) +{ +type_register_static (&lbus_info); +type_register_static (&lbus_device_type_info); +} + +type_init (lbus_register_types);hw/fsi/meson.build new file +1
-0@@ -0,0 +1 @@ +system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c'))hw/meson.build +1
-0@@ -43,6 +43,7 @@ subdir('virtio') subdir('watchdog') subdir('xen') subdir('xenpv') +subdir('fsi') subdir('alpha') subdir('arm')include/hw/fsi/lbus.h new file +4
-0@@ -0,0 +1,48 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +*
include/hw/fsi/lbus.h line 14
Quoted 10 lines
include/hw/fsi/lbus.h new file +10
-0+* IBM Local bus and connected device structures. +*/ +#ifndef FSI_LBUS_H +#define FSI_LBUS_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" + +#define TYPE_LBUS_DEVICE "lbus.device" +OBJECT_DECLARE_TYPE (LBusDevice, LBusDeviceClass,LBUS_DEVICE )
Using an "fsi/FSI" prefix for all definitions seems like a good idea to avoid namespace conflicts.
Quoted 18 lines
include/hw/fsi/lbus.h new file +18
-0+typedef struct LBusDevice { +DeviceState parent; + +MemoryRegion iomem; +uint32_t address; +}LBusDevice ; + +typedef struct LBusDeviceClass { +DeviceClass parent; + +uint32_t config; +}LBusDeviceClass ; + +typedef struct LBusNode { +LBusDevice *ldev; + +QLIST_ENTRY (LBusNode) next; +}LBusNode ;
include/hw/fsi/lbus.h line 43
Quoted 10 lines
include/hw/fsi/lbus.h new file +10
-0+ +#define TYPE_LBUS "lbus" +OBJECT_DECLARE_SIMPLE_TYPE(LBus, LBUS) + +typedef struct LBus { + BusState bus; + + MemoryRegion mr; + + QLIST_HEAD(, LBusNode) devices;
BusState already has a list. I think this needs to be reworked.
Quoted 10 lines
include/hw/fsi/lbus.h new file +5
-0+} LBus; + +DeviceState *lbus_create_device (LBus *bus,const char *type,uint32_t addr); +int lbus_add_device (LBus *bus,LBusDevice *dev); +#endif /* FSI_LBUS_H */ include/qemu/bitops.h +0
-0
include/qemu/bitops.h static inline uint64_t half_unshuffle64(uint64_t x) · line 625
Quoted 8 lines
include/qemu/bitops.h +5
-0@@ -618,4 +618,10 @@ static inline uint64_t half_unshuffle64(uint64_t x)return x; } +/* Bitwise operations at the word level. */ +#define BE_BIT (x) BIT(31 - (x)) +#define GENMASK (t, b) \ + (((1ULL << ((t) + 1)) - 1) & ~((1ULL << (b)) - 1)) +#define BE_GENMASK (t, b) GENMASK(BE_BIT(t), BE_BIT(b))
I think we should rework the code to make these macro local to the fsi subsystem, in the fsi.h file, or even better get rid of them.
Thanks,
C.
Quoted 1 line
include/qemu/bitops.h +0
-0#endif
Re: [PATCH v4 02/10] hw/fsi: Introduce IBM's scratchpad
In reply to Ninad PalsuleQuoted 4 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS device is embeded inside the scratchpad. The scratchpad
embedded
Quoted 46 lines
provides a non-functional registers. There is a 1-1 relation between scratchpad and LBUS devices. Each LBUS device has 1K memory mapped in the LBUS.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.--- hw/fsi/Kconfig | 4 ++ hw/fsi/engine-scratchpad.c | 100 +++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 + include/hw/fsi/engine-scratchpad.h | 33 ++++++++++ 4 files changed, 138 insertions(+)create mode 100644
hw/fsi/engine-scratchpad.ccreate mode 100644include/hw/fsi/engine-scratchpad.hhw/fsi/Kconfig +4
-0@@ -1,2 +1,6 @@ +config SCRATCHPAD + bool + select LBUS + config LBUS boolhw/fsi/engine-scratchpad.c new file +10
-0@@ -0,0 +1,100 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engine +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h"
hw/fsi/engine-scratchpad.c line 20
Quoted 10 lines
hw/fsi/engine-scratchpad.c new file +10
-0+#include "qemu/log.h" + +#include "hw/fsi/engine-scratchpad.h" + +static uint64_t scratchpad_read (void *opaque,hwaddr addr,unsigned size) +{ +ScratchPad *s =SCRATCHPAD (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: read @0x%" HWADDR_PRIx" size=%d\n" , + __func__, addr, size);
This should be a trace event. The comment applies to all similar usage.
hw/fsi/engine-scratchpad.c line 26
Quoted 6 lines
hw/fsi/engine-scratchpad.c new file +6
-0+ +if (addr) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds read: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return 0 ;
if the MMIO region is correctly sized, this should not be necessary. Do you plans to add support for registers ?
hw/fsi/engine-scratchpad.c line 38
Quoted 12 lines
hw/fsi/engine-scratchpad.c new file +12
-0+ } + +return s->reg; +} + +static void scratchpad_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +ScratchPad *s =SCRATCHPAD (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: write @0x%" HWADDR_PRIx" size=%d " +"value=%" PRIx64"\n" , __func__, addr, size, data);
trace event
Quoted 36 lines
hw/fsi/engine-scratchpad.c new file +36
-0+ +if (addr) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds write: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return ; + } + + s->reg = data; +} + +static const struct MemoryRegionOps scratchpad_ops = { + .read = scratchpad_read, + .write = scratchpad_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void scratchpad_realize (DeviceState *dev,Error **errp) +{ +LBusDevice *ldev =LBUS_DEVICE (dev); + +memory_region_init_io (&ldev->iomem,OBJECT (ldev), &scratchpad_ops, + ldev,TYPE_SCRATCHPAD ,0x400 ); +} + +static void scratchpad_reset (DeviceState *dev) +{ +ScratchPad *s =SCRATCHPAD (dev); + + s->reg =0 ; +} + +static void scratchpad_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); +LBusDeviceClass *ldc =LBUS_DEVICE_CLASS (klass);
hw/fsi/engine-scratchpad.c line 84
Quoted 10 lines
hw/fsi/engine-scratchpad.c new file +10
-0+ + dc->realize = scratchpad_realize; + dc->reset = scratchpad_reset; + + ldc->config = +ENGINE_CONFIG_NEXT /* valid */ + |0x00010000 /* slots */ + |0x00001000 /* version */ + |ENGINE_CONFIG_TYPE_SCRATCHPAD /* type */ + |0x00000007 ;/* crc */
where is ->config used ?
Quoted 62 lines
hw/fsi/engine-scratchpad.c new file +16
-0+} + +static const TypeInfo scratchpad_info = { + .name =TYPE_SCRATCHPAD , + .parent =TYPE_LBUS_DEVICE , + .instance_size =sizeof (ScratchPad), + .class_init = scratchpad_class_init, + .class_size =sizeof (LBusDeviceClass), +}; + +static void scratchpad_register_types (void ) +{ +type_register_static (&scratchpad_info); +} + +type_init (scratchpad_register_types);hw/fsi/meson.build +1
-0@@ -1 +1,2 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c'))include/hw/fsi/engine-scratchpad.h new file +33
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engne +*/ +#ifndef FSI_ENGINE_SCRATCHPAD_H +#define FSI_ENGINE_SCRATCHPAD_H + +#include "qemu/bitops.h" + +#include "hw/fsi/lbus.h" + +#define ENGINE_CONFIG_NEXT BE_BIT(0) +#define ENGINE_CONFIG_VPD BE_BIT(1) +#define ENGINE_CONFIG_SLOTS BE_GENMASK(8, 15) +#define ENGINE_CONFIG_VERSION BE_GENMASK(16, 19) +#define ENGINE_CONFIG_TYPE BE_GENMASK(20, 27) +#define ENGINE_CONFIG_TYPE_PEEK (0x02 << 4) +#define ENGINE_CONFIG_TYPE_FSI (0x03 << 4) +#define ENGINE_CONFIG_TYPE_SCRATCHPAD (0x06 << 4) +#define ENGINE_CONFIG_CRC BE_GENMASK(28, 31) + +#define TYPE_SCRATCHPAD "scratchpad" +#define SCRATCHPAD (obj) OBJECT_CHECK(ScratchPad, (obj), TYPE_SCRATCHPAD) + +typedef struct ScratchPad { +LBusDevice parent; + +uint32_t reg; +}ScratchPad ; + +#endif /* FSI_ENGINE_SCRATCHPAD_H */
Re: [PATCH v4 03/10] hw/fsi: Introduce IBM's cfam,fsi-slave
In reply to Ninad PalsuleQuoted 91 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on busses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
v3:
- Incorporated Thomas Huth's review comments.--- hw/fsi/Kconfig | 9 ++ hw/fsi/cfam.c | 238 +++++++++++++++++++++++++++++++++++++ hw/fsi/fsi-slave.c | 109 +++++++++++++++++ hw/fsi/meson.build | 2 + hw/fsi/trace-events | 5 + include/hw/fsi/cfam.h | 61 ++++++++++ include/hw/fsi/fsi-slave.h | 29 +++++ 7 files changed, 453 insertions(+)create mode 100644
hw/fsi/cfam.c
create mode 100644hw/fsi/fsi-slave.c
create mode 100644 hw/fsi/trace-events
create mode 100644include/hw/fsi/cfam.h
create mode 100644include/hw/fsi/fsi-slave.hhw/fsi/Kconfig +9
-0@@ -1,3 +1,12 @@ +config CFAM + bool + select FSI + select SCRATCHPAD + select LBUS + +config FSI + bool + config SCRATCHPAD bool select LBUShw/fsi/cfam.c new file +31
-0@@ -0,0 +1,238 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Common FRU Access Macro +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" +#include "trace.h" + +#include "hw/fsi/bits.h" +#include "hw/fsi/cfam.h" +#include "hw/fsi/engine-scratchpad.h" + +#include "hw/qdev-properties.h" + +#define TO_REG (x) ((x) >> 2) + +#define CFAM_ENGINE_CONFIG TO_REG(0x04) + +#define CFAM_CONFIG_CHIP_ID TO_REG(0x00) +#define CFAM_CONFIG_CHIP_ID_P9 0xc0022d15 +#define CFAM_CONFIG_CHIP_ID_BREAK 0xc0de0000 + +static uint64_t cfam_config_read (void *opaque,hwaddr addr,unsigned size) +{ +CFAMConfig *config; +CFAMState *cfam;
hw/fsi/cfam.c line 41
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+LBusNode *node; +int i; + + config =CFAM_CONFIG (opaque); + cfam =container_of (config, CFAMState, config); + +trace_cfam_config_read (addr, size); + +assert (size ==4 ); +assert (!(addr &3 ));
These checks are useless if the MemoryRegionOps is defined accordingly.
Quoted 9 lines
hw/fsi/cfam.c new file +9
-0+ +switch (addr) { +case 0x00 : +return CFAM_CONFIG_CHIP_ID_P9 ; +case 0x04 : +return ENGINE_CONFIG_NEXT + |0x00010000 /* slots */ + |0x00001000 /* version */ + |ENGINE_CONFIG_TYPE_PEEK /* type */
hw/fsi/cfam.c line 60
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+ | 0x0000000c; /* crc */ +case 0x08 : +return ENGINE_CONFIG_NEXT + |0x00010000 /* slots */ + |0x00005000 /* version */ + |ENGINE_CONFIG_TYPE_FSI /* type */ + |0x0000000a ;/* crc */ +break ; +default : +/* FIXME: Improve this */
This looks hacky. What is it suppose to do ?
Quoted 8 lines
hw/fsi/cfam.c new file +8
-0+ i =0xc ; + QLIST_FOREACH(node, &cfam->lbus.devices, next) { +if (i == addr) { +return LBUS_DEVICE_GET_CLASS (node->ldev)->config; + } + i += size; + } +
hw/fsi/cfam.c line 78
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+if (i == addr) { +return 0 ; + } + +/* +* As per FSI specification, This is a magic value at address 0 of +* given FSI port. This causes FSI master to send BREAK command for +* initialization and recovery. +*/ +return 0xc0de0000 ;
we could use a definition.
hw/fsi/cfam.c line 90
Quoted 12 lines
hw/fsi/cfam.c new file +12
-0+ } +} + +static void cfam_config_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +CFAMConfig *s =CFAM_CONFIG (opaque); + +trace_cfam_config_write (addr, size, data); + +assert (size ==4 ); +assert (!(addr &3 ));
These checks are useless if the MemoryRegionOps is defined accordingly.
Quoted 23 lines
hw/fsi/cfam.c new file +23
-0+ +switch (TO_REG (addr)) { +case CFAM_CONFIG_CHIP_ID : +case CFAM_CONFIG_CHIP_ID +4 : +if (data ==CFAM_CONFIG_CHIP_ID_BREAK ) { +bus_cold_reset (qdev_get_parent_bus (DEVICE (s))); + } +break ; +default : +qemu_log_mask (LOG_GUEST_ERROR ,"%s: Not implemented: 0x%" + HWADDR_PRIx" for %u\n" , + __func__, addr, size); + } +} + +static const struct MemoryRegionOps cfam_config_ops = { + .read = cfam_config_read, + .write = cfam_config_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void cfam_config_realize (DeviceState *dev,Error **errp) +{
hw/fsi/cfam.c line 123
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+CFAMConfig *s =CFAM_CONFIG (dev); + +memory_region_init_io (&s->iomem,OBJECT (s), &cfam_config_ops, s, +TYPE_CFAM_CONFIG ,0x400 ); +} + +static void cfam_config_reset (DeviceState *dev) +{ +/* Config is read-only */ +}
Simply remove.
Quoted 39 lines
hw/fsi/cfam.c new file +39
-0+ +static void cfam_config_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + dc->bus_type =TYPE_LBUS ; + dc->realize = cfam_config_realize; + dc->reset = cfam_config_reset; +} + +static const TypeInfo cfam_config_info = { + .name =TYPE_CFAM_CONFIG , + .parent =TYPE_DEVICE , + .instance_size =sizeof (CFAMConfig), + .class_init = cfam_config_class_init, +}; + +static uint64_t cfam_unimplemented_read (void *opaque,hwaddr addr, +unsigned size) +{ +trace_cfam_unimplemented_read (addr, size); + +return 0 ; +} + +static void cfam_unimplemented_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +trace_cfam_unimplemented_write (addr, size, data); +} + +static const struct MemoryRegionOps cfam_unimplemented_ops = { + .read = cfam_unimplemented_read, + .write = cfam_unimplemented_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void cfam_realize (DeviceState *dev,Error **errp) +{ +CFAMState *cfam =CFAM (dev);
hw/fsi/cfam.c line 172
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+FSISlaveState *slave =FSI_SLAVE (dev); +Error *err =NULL ; + +/* Each slave has a 2MiB address space */ +memory_region_init_io (&cfam->mr,OBJECT (cfam), &cfam_unimplemented_ops, + cfam,TYPE_CFAM ,2 *1024 *1024 ); +address_space_init (&cfam->as, &cfam->mr,TYPE_CFAM ); + +qbus_init (&cfam->lbus,sizeof (cfam->lbus),TYPE_LBUS , +DEVICE (cfam),NULL );
shouldn't that be in the cfam_init routine ? not sure.
hw/fsi/cfam.c line 181
Quoted 7 lines
hw/fsi/cfam.c new file +7
-0+lbus_create_device (&cfam->lbus,TYPE_SCRATCHPAD ,0 ); + + object_property_set_bool(OBJECT(&cfam->config), "realized", true, &err);> + if (err) { +error_propagate (errp, err); +return ; + } +qdev_set_parent_bus (DEVICE (&cfam->config),BUS (&cfam->lbus), &error_abort);
why isn't cfam->config created with lbus_create_device() ?
Quoted 7 lines
hw/fsi/cfam.c new file +7
-0+object_property_set_bool (OBJECT (&cfam->lbus),"realized" , true, &err); +if (err) { +error_propagate (errp, err); +return ; + } + +memory_region_add_subregion (&cfam->mr,0 , &cfam->config.iomem);
hw/fsi/cfam.c line 199
Quoted 10 lines
hw/fsi/cfam.c new file +10
-0+/* memory_region_add_subregion(&cfam->mr, 0x800, &cfam->lbus.peek.iomem); */ +memory_region_add_subregion (&cfam->mr,0x800 , &slave->iomem); +memory_region_add_subregion (&cfam->mr,0xc00 , &cfam->lbus.mr); +} + +static void cfam_reset (DeviceState *dev) +{ +/* TODO: Figure out how inherited reset works */ +qemu_log_mask (LOG_UNIMP ,"%s: Not implemented yet.\n" , __func__); +}
Simply remove for now.
Quoted 76 lines
hw/fsi/cfam.c new file +39
-0+ +static void cfam_init (Object *o) +{ +CFAMState *s =CFAM (o); + +object_initialize_child (o,TYPE_CFAM_CONFIG , &s->config,TYPE_CFAM_CONFIG ); +} + +static void cfam_finalize (Object *o) +{ +CFAMState *s =CFAM (o); + +address_space_destroy (&s->as); +} + +static void cfam_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + dc->bus_type =TYPE_FSI_BUS ; + dc->realize = cfam_realize; + dc->reset = cfam_reset; +} + +static const TypeInfo cfam_info = { + .name =TYPE_CFAM , + .parent =TYPE_FSI_SLAVE , + .instance_init = cfam_init, + .instance_finalize = cfam_finalize, + .instance_size =sizeof (CFAMState), + .class_init = cfam_class_init, +}; + +static void cfam_register_types (void ) +{ +type_register_static (&cfam_config_info); +type_register_static (&cfam_info); +} + +type_init (cfam_register_types);hw/fsi/fsi-slave.c new file +31
-0@@ -0,0 +1,109 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface slave +*/ + +#include "qemu/osdep.h" + +#include "qemu/bitops.h" +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/fsi-slave.h" + +#define TO_REG (x) ((x) >> 2) + +#define FSI_SMODE TO_REG(0x00) +#define FSI_SMODE_WSTART BE_BIT(0) +#define FSI_SMODE_AUX_EN BE_BIT(1) +#define FSI_SMODE_SLAVE_ID BE_GENMASK(6, 7) +#define FSI_SMODE_ECHO_DELAY BE_GENMASK(8, 11) +#define FSI_SMODE_SEND_DELAY BE_GENMASK(12, 15) +#define FSI_SMODE_LBUS_DIV BE_GENMASK(20, 23) +#define FSI_SMODE_BRIEF_LEFT BE_GENMASK(24, 27) +#define FSI_SMODE_BRIEF_RIGHT BE_GENMASK(28, 31) + +#define FSI_SDMA TO_REG(0x04) +#define FSI_SISC TO_REG(0x08) +#define FSI_SCISC TO_REG(0x08) +#define FSI_SISM TO_REG(0x0c)
hw/fsi/fsi-slave.c line 41
Quoted 10 lines
hw/fsi/fsi-slave.c new file +10
-0+#define FSI_SISS TO_REG(0x10) +#define FSI_SSISM TO_REG(0x10) +#define FSI_SCISM TO_REG(0x14) + +static uint64_t fsi_slave_read (void *opaque,hwaddr addr,unsigned size) +{ +FSISlaveState *s =FSI_SLAVE (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: read @0x%" HWADDR_PRIx" size=%d\n" , + __func__, addr, size);
This is a trace event
hw/fsi/fsi-slave.c line 46
Quoted 4 lines
hw/fsi/fsi-slave.c new file +4
-0+if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds read: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size);
I don't think this check is necessary if the MMIO region is sized correctly.
hw/fsi/fsi-slave.c line 59
Quoted 13 lines
hw/fsi/fsi-slave.c new file +13
-0+return 0 ; + } + +return s->regs[TO_REG (addr)]; +} + +static void fsi_slave_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +FSISlaveState *s =FSI_SLAVE (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: write @0x%" HWADDR_PRIx" size=%d " +"value=%" PRIx64"\n" , __func__, addr, size, data);
This is a trace event
Quoted 18 lines
hw/fsi/fsi-slave.c new file +18
-0+if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds write: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return ; + } + + s->regs[TO_REG (addr)] = data; +} + +static const struct MemoryRegionOps fsi_slave_ops = { + .read = fsi_slave_read, + .write = fsi_slave_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void fsi_slave_init (Object *o) +{
hw/fsi/fsi-slave.c line 88
Quoted 10 lines
hw/fsi/fsi-slave.c new file +10
-0+FSISlaveState *s =FSI_SLAVE (o); + +memory_region_init_io (&s->iomem,OBJECT (s), &fsi_slave_ops, + s,TYPE_FSI_SLAVE ,0x400 ); +} + +static void fsi_slave_reset (DeviceState *dev) +{ +/* FIXME */ +}
Simply remove the reset for now.
Quoted 143 lines
hw/fsi/fsi-slave.c new file +21
-0+ +static void fsi_slave_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + dc->reset = fsi_slave_reset; +} + +static const TypeInfo fsi_slave_info = { + .name =TYPE_FSI_SLAVE , + .parent =TYPE_DEVICE , + .instance_init = fsi_slave_init, + .instance_size =sizeof (FSISlaveState), + .class_init = fsi_slave_class_init, +}; + +static void fsi_slave_register_types (void ) +{ +type_register_static (&fsi_slave_info); +} + +type_init (fsi_slave_register_types);hw/fsi/meson.build +2
-0@@ -1,2 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c'))hw/fsi/trace-events new file +5
-0@@ -0,0 +1,5 @@ +cfam_config_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +cfam_config_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 + +cfam_unimplemented_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +cfam_unimplemented_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64include/hw/fsi/cfam.h new file +61
-0@@ -0,0 +1,61 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Common FRU Access Macro +*/ +#ifndef FSI_CFAM_H +#define FSI_CFAM_H + +#include "exec/memory.h" + +#include "hw/fsi/fsi-slave.h" +#include "hw/fsi/lbus.h" + +#define TYPE_FSI_BUS "fsi.bus" + +#define TYPE_CFAM "cfam" +#define CFAM (obj) OBJECT_CHECK(CFAMState, (obj), TYPE_CFAM) + +#define CFAM_NR_REGS ((0x2e0 >> 2) + 1) + +#define TYPE_CFAM_CONFIG "cfam.config" +#define CFAM_CONFIG (obj) \ + OBJECT_CHECK(CFAMConfig, (obj), TYPE_CFAM_CONFIG) +/* P9-ism */ +#define CFAM_CONFIG_NR_REGS 0x28 + +typedef struct CFAMState CFAMState ; + +/* TODO: Generalise this accommodate different CFAM configurations */ +typedef struct CFAMConfig { +DeviceState parent; + +MemoryRegion iomem; +}CFAMConfig ; + +#define TYPE_CFAM_PEEK "cfam.peek" +#define CFAM_PEEK (obj) \ + OBJECT_CHECK(CFAMPeek, (obj), TYPE_CFAM_PEEK) +#define CFAM_PEEK_NR_REGS ((0x130 >> 2) + 1) + +typedef struct CFAMPeek { +DeviceState parent; + +MemoryRegion iomem; +}CFAMPeek ; + +struct CFAMState { +/* < private > */ +FSISlaveState parent; + +MemoryRegion mr; +AddressSpace as; + +CFAMConfig config; +CFAMPeek peek; + +LBus lbus; +}; + +#endif /* FSI_CFAM_H */ include/hw/fsi/fsi-slave.h new file +29
-0@@ -0,0 +1,29 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface slave +*/ +#ifndef FSI_FSI_SLAVE_H +#define FSI_FSI_SLAVE_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" + +#include "hw/fsi/lbus.h" + +#include <stdint.h> + +#define TYPE_FSI_SLAVE "fsi.slave" +#define FSI_SLAVE (obj) \ + OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +#define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1) + +typedef struct FSISlaveState { +DeviceState parent; + +MemoryRegion iomem; +uint32_t regs[FSI_SLAVE_CONTROL_NR_REGS ]; +}FSISlaveState ; + +#endif /* FSI_FSI_H */
Re: [PATCH v4 02/10] hw/fsi: Introduce IBM's scratchpad
In reply to Ninad PalsuleQuoted 7 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS device is embeded inside the scratchpad. The scratchpad provides a non-functional registers. There is a 1-1 relation between scratchpad and LBUS devices. Each LBUS device has 1K memory mapped in the LBUS.
The commit log is a bit confusing.
C.
Quoted 179 lines
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.--- hw/fsi/Kconfig | 4 ++ hw/fsi/engine-scratchpad.c | 100 +++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 + include/hw/fsi/engine-scratchpad.h | 33 ++++++++++ 4 files changed, 138 insertions(+)create mode 100644
hw/fsi/engine-scratchpad.ccreate mode 100644include/hw/fsi/engine-scratchpad.hhw/fsi/Kconfig +4
-0@@ -1,2 +1,6 @@ +config SCRATCHPAD + bool + select LBUS + config LBUS boolhw/fsi/engine-scratchpad.c new file +100
-0@@ -0,0 +1,100 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engine +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/engine-scratchpad.h" + +static uint64_t scratchpad_read (void *opaque,hwaddr addr,unsigned size) +{ +ScratchPad *s =SCRATCHPAD (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: read @0x%" HWADDR_PRIx" size=%d\n" , + __func__, addr, size); + +if (addr) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds read: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return 0 ; + } + +return s->reg; +} + +static void scratchpad_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +ScratchPad *s =SCRATCHPAD (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: write @0x%" HWADDR_PRIx" size=%d " +"value=%" PRIx64"\n" , __func__, addr, size, data); + +if (addr) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds write: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return ; + } + + s->reg = data; +} + +static const struct MemoryRegionOps scratchpad_ops = { + .read = scratchpad_read, + .write = scratchpad_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void scratchpad_realize (DeviceState *dev,Error **errp) +{ +LBusDevice *ldev =LBUS_DEVICE (dev); + +memory_region_init_io (&ldev->iomem,OBJECT (ldev), &scratchpad_ops, + ldev,TYPE_SCRATCHPAD ,0x400 ); +} + +static void scratchpad_reset (DeviceState *dev) +{ +ScratchPad *s =SCRATCHPAD (dev); + + s->reg =0 ; +} + +static void scratchpad_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); +LBusDeviceClass *ldc =LBUS_DEVICE_CLASS (klass); + + dc->realize = scratchpad_realize; + dc->reset = scratchpad_reset; + + ldc->config = +ENGINE_CONFIG_NEXT /* valid */ + |0x00010000 /* slots */ + |0x00001000 /* version */ + |ENGINE_CONFIG_TYPE_SCRATCHPAD /* type */ + |0x00000007 ;/* crc */ +} + +static const TypeInfo scratchpad_info = { + .name =TYPE_SCRATCHPAD , + .parent =TYPE_LBUS_DEVICE , + .instance_size =sizeof (ScratchPad), + .class_init = scratchpad_class_init, + .class_size =sizeof (LBusDeviceClass), +}; + +static void scratchpad_register_types (void ) +{ +type_register_static (&scratchpad_info); +} + +type_init (scratchpad_register_types);hw/fsi/meson.build +1
-0@@ -1 +1,2 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c'))include/hw/fsi/engine-scratchpad.h new file +33
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engne +*/ +#ifndef FSI_ENGINE_SCRATCHPAD_H +#define FSI_ENGINE_SCRATCHPAD_H + +#include "qemu/bitops.h" + +#include "hw/fsi/lbus.h" + +#define ENGINE_CONFIG_NEXT BE_BIT(0) +#define ENGINE_CONFIG_VPD BE_BIT(1) +#define ENGINE_CONFIG_SLOTS BE_GENMASK(8, 15) +#define ENGINE_CONFIG_VERSION BE_GENMASK(16, 19) +#define ENGINE_CONFIG_TYPE BE_GENMASK(20, 27) +#define ENGINE_CONFIG_TYPE_PEEK (0x02 << 4) +#define ENGINE_CONFIG_TYPE_FSI (0x03 << 4) +#define ENGINE_CONFIG_TYPE_SCRATCHPAD (0x06 << 4) +#define ENGINE_CONFIG_CRC BE_GENMASK(28, 31) + +#define TYPE_SCRATCHPAD "scratchpad" +#define SCRATCHPAD (obj) OBJECT_CHECK(ScratchPad, (obj), TYPE_SCRATCHPAD) + +typedef struct ScratchPad { +LBusDevice parent; + +uint32_t reg; +}ScratchPad ; + +#endif /* FSI_ENGINE_SCRATCHPAD_H */
Re: [PATCH v4 04/10] hw/fsi: Introduce IBM's FSI
In reply to Ninad PalsuleQuoted 43 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
This commit models the FSI bus. CFAM is hanging out of FSI bus. The bus is model such a way that it is embeded inside the FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>Reviewed-by Joel Stanley <[email protected]>---
v2:
- Incorporated review comments by Joel--- hw/fsi/cfam.c | 3 +- hw/fsi/fsi-master.c | 203 ++++++++++++++++++++++++++++++++++++ hw/fsi/fsi.c | 54 ++++++++++ hw/fsi/meson.build | 2 +- include/hw/fsi/cfam.h | 8 +- include/hw/fsi/fsi-master.h | 30 ++++++ include/hw/fsi/fsi-slave.h | 4 +- include/hw/fsi/fsi.h | 31 ++++++ 8 files changed, 327 insertions(+), 8 deletions(-)create mode 100644
hw/fsi/fsi-master.c
create mode 100644hw/fsi/fsi.c
create mode 100644include/hw/fsi/fsi-master.h
create mode 100644include/hw/fsi/fsi.hhw/fsi/cfam.c +1
-0@@ -7,12 +7,13 @@#include "qemu/osdep.h" +#include "qemu/bitops.h"
hw/fsi/cfam.c line 19
Quoted 10 lines
hw/fsi/cfam.c +1
-1#include "qapi/error.h" #include "qemu/log.h" #include "trace.h" -#include "hw/fsi/bits.h" #include "hw/fsi/cfam.h" +#include "hw/fsi/fsi.h" #include "hw/fsi/engine-scratchpad.h" #include "hw/qdev-properties.h"
These change do not belong to this patch.
Quoted 80 lines
hw/fsi/fsi-master.c new file +74
-0@@ -0,0 +1,203 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface master +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" + +#include "qemu/log.h" + +#include "hw/fsi/bits.h" +#include "hw/fsi/fsi-master.h" + +#define TYPE_OP_BUS "opb" + +#define TO_REG (x) ((x) >> 2) + +#define FSI_MMODE TO_REG(0x000) +#define FSI_MMODE_IPOLL_DMA_EN BE_BIT(0) +#define FSI_MMODE_HW_ERROR_RECOVERY_EN BE_BIT(1) +#define FSI_MMODE_RELATIVE_ADDRESS_EN BE_BIT(2) +#define FSI_MMODE_PARITY_CHECK_EN BE_BIT(3) +#define FSI_MMODE_CLOCK_DIVIDER_0 BE_GENMASK(4, 13) +#define FSI_MMODE_CLOCK_DIVIDER_1 BE_GENMASK(14, 23) +#define FSI_MMODE_DEBUG_EN BE_BIT(24) + +#define FSI_MDELAY TO_REG(0x004) +#define FSI_MDELAY_ECHO_0 BE_GENMASK(0, 3) +#define FSI_MDELAY_SEND_0 BE_GENMASK(4, 7) +#define FSI_MDELAY_ECHO_1 BE_GENMASK(8, 11) +#define FSI_MDELAY_SEND_1 BE_GENMASK(12, 15) + +#define FSI_MENP0 TO_REG(0x010) +#define FSI_MENP32 TO_REG(0x014) +#define FSI_MSENP0 TO_REG(0x018) +#define FSI_MLEVP0 TO_REG(0x018) +#define FSI_MSENP32 TO_REG(0x01c) +#define FSI_MLEVP32 TO_REG(0x01c) +#define FSI_MCENP0 TO_REG(0x020) +#define FSI_MREFP0 TO_REG(0x020) +#define FSI_MCENP32 TO_REG(0x024) +#define FSI_MREFP32 TO_REG(0x024) + +#define FSI_MAEB TO_REG(0x070) +#define FSI_MAEB_ANY_CPU_ERROR BE_BIT(0) +#define FSI_MAEB_ANY_DMA_ERROR BE_GENMASK(1, 16) +#define FSI_MAEB_ANY_PARITY_ERROR BE_BIT(17) + +#define FSI_MVER TO_REG(0x074) +#define FSI_MVER_VERSION BE_GENMASK(0, 7) +#define FSI_MVER_BRIDGES BE_GENMASK(8, 15) +#define FSI_MVER_PORTS BE_GENMASK(16, 23) + +#define FSI_MRESP0 TO_REG(0x0d0) +#define FSI_MRESP0_RESET_PORT_GENERAL BE_BIT(0) +#define FSI_MRESP0_RESET_PORT_ERROR BE_BIT(1) +#define FSI_MRESP0_RESET_ALL_BRIDGES_GENERAL BE_BIT(2) +#define FSI_MRESP0_RESET_ALL_PORTS_GENERAL BE_BIT(3) +#define FSI_MRESP0_RESET_MASTER BE_BIT(4) +#define FSI_MRESP0_RESET_PARITY_ERROR_LATCH BE_BIT(5) + +#define FSI_MRESB0 TO_REG(0x1d0) +#define FSI_MRESB0_RESET_GENERAL BE_BIT(0) +#define FSI_MRESB0_RESET_ERROR BE_BIT(1) +#define FSI_MRESB0_SET_DMA_SUSPEND BE_BIT(5) +#define FSI_MRESB0_CLEAR_DMA_SUSPEND BE_BIT(6) +#define FSI_MRESB0_SET_DELAY_MEASURE BE_BIT(7) + +#define FSI_MECTRL TO_REG(0x2e0) +#define FSI_MECTRL_TEST_PULSE BE_GENMASK(0, 7) +#define FSI_MECTRL_INHIBIT_PARITY_ERROR BE_GENMASK(8, 15)
hw/fsi/fsi-master.c line 84
Quoted 10 lines
hw/fsi/fsi-master.c new file +10
-0+#define FSI_MECTRL_ENABLE_OPB_ERR_ACK BE_BIT(16) +#define FSI_MECTRL_AUTO_TERMINATE BE_BIT(17) +#define FSI_MECTRL_PORT_ERROR_FREEZE BE_BIT(18) + +static uint64_t fsi_master_read (void *opaque,hwaddr addr,unsigned size) +{ +FSIMasterState *s =FSI_MASTER (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: read @0x%" HWADDR_PRIx" size=%d\n" , + __func__, addr, size);
This should be a trace event.
Quoted 8 lines
hw/fsi/fsi-master.c new file +8
-0+ +if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds read: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return 0 ; + } +
hw/fsi/fsi-master.c line 102
Quoted 10 lines
hw/fsi/fsi-master.c new file +10
-0+return s->regs[TO_REG (addr)]; +} + +static void fsi_master_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +FSIMasterState *s =FSI_MASTER (opaque); + +qemu_log_mask (LOG_UNIMP ,"%s: write @0x%" HWADDR_PRIx" size=%d " +"value=%" PRIx64"\n" , __func__, addr, size, data);
This should be a trace event.
Quoted 115 lines
hw/fsi/fsi-master.c new file +100
-0+if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds write: %" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return ; + } + +switch (TO_REG (addr)) { +case FSI_MENP0 : + s->regs[FSI_MENP0 ] = data; +break ; +case FSI_MENP32 : + s->regs[FSI_MENP32 ] = data; +break ; +case FSI_MSENP0 : + s->regs[FSI_MENP0 ] |= data; +break ; +case FSI_MSENP32 : + s->regs[FSI_MENP32 ] |= data; +break ; +case FSI_MCENP0 : + s->regs[FSI_MENP0 ] &= ~data; +break ; +case FSI_MCENP32 : + s->regs[FSI_MENP32 ] &= ~data; +break ; +case FSI_MRESP0 : +/* Perform necessary resets leave register 0 to indicate no errors */ +break ; +case FSI_MRESB0 : +if (data &FSI_MRESB0_RESET_GENERAL ) { +device_cold_reset (DEVICE (opaque)); + } +if (data &FSI_MRESB0_RESET_ERROR ) { +/* FIXME: this seems dubious */ +device_cold_reset (DEVICE (opaque)); + } +break ; +default : + s->regs[TO_REG (addr)] = data; + } +} + +static const struct MemoryRegionOps fsi_master_ops = { + .read = fsi_master_read, + .write = fsi_master_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void fsi_master_realize (DeviceState *dev,Error **errp) +{ +FSIMasterState *s =FSI_MASTER (dev); +Error *err =NULL ; + +qbus_init (&s->bus,sizeof (s->bus),TYPE_FSI_BUS ,DEVICE (s),NULL ); + +memory_region_init_io (&s->iomem,OBJECT (s), &fsi_master_ops, s, +TYPE_FSI_MASTER ,0x10000000 ); +memory_region_init (&s->opb2fsi,OBJECT (s),"fsi.opb2fsi" ,0x10000000 ); + +object_property_set_bool (OBJECT (&s->bus),"realized" , true, &err); +if (err) { +error_propagate (errp, err); +return ; + } + +memory_region_add_subregion (&s->opb2fsi,0 , &s->bus.slave.mr); +} + +static void fsi_master_reset (DeviceState *dev) +{ +FSIMasterState *s =FSI_MASTER (dev); + +/* ASPEED default */ + s->regs[FSI_MVER ] =0xe0050101 ; +} + +static void fsi_master_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + + dc->bus_type =TYPE_OP_BUS ; + dc->desc ="FSI Master" ; + dc->realize = fsi_master_realize; + dc->reset = fsi_master_reset; +} + +static const TypeInfo fsi_master_info = { + .name =TYPE_FSI_MASTER , + .parent =TYPE_DEVICE , + .instance_size =sizeof (FSIMasterState), + .class_init = fsi_master_class_init, +}; + +static void fsi_register_types (void ) +{ +type_register_static (&fsi_master_info); +} + +type_init (fsi_register_types);hw/fsi/fsi.c new file +9
-0@@ -0,0 +1,54 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface +*/ +#include "qemu/osdep.h" + +#include "qapi/error.h"
hw/fsi/fsi.c line 19
Quoted 10 lines
hw/fsi/fsi.c new file +10
-0+ +#include "hw/fsi/fsi.h" +#include "hw/fsi/cfam.h" + +static void fsi_bus_realize (BusState *bus,Error **errp) +{ +FSIBus *s =FSI_BUS (bus); +Error *err =NULL ; + +/* FIXME: Should be realised elsewhere and added to the bus */
indeed.
hw/fsi/fsi.c line 30
Quoted 11 lines
hw/fsi/fsi.c new file +11
-0+object_property_set_bool (OBJECT (&s->slave),"realized" , true, &err); +if (err) { +error_propagate (errp, err); + } +} + +static void fsi_bus_init (Object *o) +{ +FSIBus *s =FSI_BUS (o); + +/* FIXME: Move this elsewhere */
at the board level may be ?
Quoted 39 lines
hw/fsi/fsi.c new file +24
-0+object_initialize_child (o,TYPE_CFAM , &s->slave,TYPE_CFAM ); +qdev_set_parent_bus (DEVICE (&s->slave),BUS (o), &error_abort); +} + +static void fsi_bus_class_init (ObjectClass *klass,void *data) +{ +BusClass *bc =BUS_CLASS (klass); + bc->realize = fsi_bus_realize; +} + +static const TypeInfo fsi_bus_info = { + .name =TYPE_FSI_BUS , + .parent =TYPE_BUS , + .instance_init = fsi_bus_init, + .instance_size =sizeof (FSIBus), + .class_init = fsi_bus_class_init, +}; + +static void fsi_bus_register_types (void ) +{ +type_register_static (&fsi_bus_info); +} + +type_init (fsi_bus_register_types);hw/fsi/meson.build +1
-1@@ -1,4 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) -system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c')) +system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c'))include/hw/fsi/cfam.h +0
-0
include/hw/fsi/cfam.h line 16
Quoted 5 lines
include/hw/fsi/cfam.h +0
-2@@ -12,14 +12,14 @@#include "hw/fsi/fsi-slave.h" #include "hw/fsi/lbus.h" -#define TYPE_FSI_BUS "fsi.bus" -
unwanted change I guess ?
include/hw/fsi/cfam.h line 22
Quoted 8 lines
include/hw/fsi/cfam.h +2
-0#define TYPE_CFAM "cfam"#define CFAM (obj) OBJECT_CHECK(CFAMState, (obj), TYPE_CFAM)#define CFAM_NR_REGS ((0x2e0 >> 2) + 1)#define TYPE_CFAM_CONFIG "cfam.config" +OBJECT_DECLARE_SIMPLE_TYPE (CFAMConfig,CFAM_CONFIG ) +
same.
Quoted 55 lines
include/hw/fsi/cfam.h +2
-2#define CFAM_CONFIG (obj) \ OBJECT_CHECK(CFAMConfig, (obj), TYPE_CFAM_CONFIG)/* P9-ism */ @@ -35,8 +35,8 @@ typedef struct CFAMConfig { } CFAMConfig;#define TYPE_CFAM_PEEK "cfam.peek" -#define CFAM_PEEK (obj) \ - OBJECT_CHECK(CFAMPeek, (obj), TYPE_CFAM_PEEK) +OBJECT_DECLARE_SIMPLE_TYPE(CFAMPeek, CFAM_PEEK) +#define CFAM_PEEK_NR_REGS ((0x130 >> 2) + 1) typedef struct CFAMPeek {include/hw/fsi/fsi-master.h new file +30
-0@@ -0,0 +1,30 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2019 IBM Corp. +* +* IBM Flexible Service Interface Master +*/ +#ifndef FSI_FSI_MASTER_H +#define FSI_FSI_MASTER_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" +#include "hw/fsi/fsi.h" + +#define TYPE_FSI_MASTER "fsi.master" +OBJECT_DECLARE_SIMPLE_TYPE(FSIMasterState, FSI_MASTER) + +#define FSI_MASTER_NR_REGS ((0x2e0 >> 2) + 1) + +typedef struct FSIMasterState { +DeviceState parent; +MemoryRegion iomem; +MemoryRegion opb2fsi; + +FSIBus bus; + +uint32_t regs[FSI_MASTER_NR_REGS ]; +}FSIMasterState ; + + +#endif /* FSI_FSI_H */ include/hw/fsi/fsi-slave.h +0
-0
include/hw/fsi/fsi-slave.h line 20
Quoted 8 lines
include/hw/fsi/fsi-slave.h +2
-2@@ -15,8 +15,8 @@#include <stdint.h> #define TYPE_FSI_SLAVE "fsi.slave" -#define FSI_SLAVE (obj) \ - OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +OBJECT_DECLARE_SIMPLE_TYPE(FSISlaveState, FSI_SLAVE) +#define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1)
These change do not belong to this patch.
Quoted 38 lines
include/hw/fsi/fsi-slave.h +0
-0typedef struct FSISlaveState {include/hw/fsi/fsi.h new file +31
-0@@ -0,0 +1,31 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface +*/ +#ifndef FSI_FSI_H +#define FSI_FSI_H + +#include "hw/qdev-core.h" + +/* +* TODO: Maybe unwind this dependency with const links? Store a +* pointer in FSIBus? +*/ +#include "hw/fsi/cfam.h" + +#define TYPE_FSI_BUS "fsi.bus" +OBJECT_DECLARE_SIMPLE_TYPE (FSIBus,FSI_BUS ) + +/* TODO: Figure out what's best with a point-to-point bus */ +typedef struct FSISlaveState FSISlaveState ; + +typedef struct FSIBus { +BusState bus; + +/* XXX: It's point-to-point, just instantiate the slave directly for now */ +CFAMState slave; +}FSIBus ; + +#endif
Re: [PATCH v4 05/10] hw/fsi: IBM's On-chip Peripheral Bus
In reply to Ninad PalsuleQuoted 48 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>Reviewed-by Joel Stanley <[email protected]>---
v2:
- Incorporated review comment by Joel.--- hw/fsi/Kconfig | 4 + hw/fsi/fsi-master.c | 6 +- hw/fsi/meson.build | 1 + hw/fsi/opb.c | 194 +++++++++++++++++++++++++++++++++++++++++++ include/hw/fsi/opb.h | 43 ++++++++++ 5 files changed, 244 insertions(+), 4 deletions(-)create mode 100644
hw/fsi/opb.c
create mode 100644include/hw/fsi/opb.hhw/fsi/Kconfig +4
-0@@ -1,3 +1,7 @@ +config OPB + bool + select CFAM + config CFAM bool select FSIhw/fsi/fsi-master.c +1
-0@@ -7,14 +7,12 @@#include "qemu/osdep.h" +#include "qemu/bitops.h" #include "qapi/error.h"
hw/fsi/fsi-master.c line 17
Quoted 10 lines
hw/fsi/fsi-master.c +1
-4-#include "qemu/log.h" -#include "hw/fsi/bits.h" #include "hw/fsi/fsi-master.h" - -#define TYPE_OP_BUS "opb" +#include "hw/fsi/opb.h" #define TO_REG (x) ((x) >> 2)
These change do not belong to this patch.
Quoted 24 lines
hw/fsi/meson.build +1
-0@@ -2,3 +2,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c')) +system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c'))hw/fsi/opb.c new file +9
-0@@ -0,0 +1,194 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM On-chip Peripheral Bus +*/ + +#include "qemu/osdep.h" +
hw/fsi/opb.c line 19
Quoted 10 lines
hw/fsi/opb.c new file +10
-0+#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/opb.h" + +static MemTxResult opb_read (OPBus *opb,hwaddr addr,void *data,size_t len) +{ +return address_space_read (&opb->as, addr,MEMTXATTRS_UNSPECIFIED , data, + len); +}
This routine doesn't look very useful. Same for the write.
hw/fsi/opb.c line 28
Quoted 9 lines
hw/fsi/opb.c new file +9
-0+ +uint8_t opb_read8 (OPBus *opb,hwaddr addr) +{ +MemTxResult tx; +uint8_t data; + + tx =opb_read (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx);
should output a qemu_log_mask(LOG_GUEST_ERROR) may be ? But I don't think we should assert.
hw/fsi/opb.c line 40
Quoted 12 lines
hw/fsi/opb.c new file +12
-0+ +return data; +} + +uint16_t opb_read16 (OPBus *opb,hwaddr addr) +{ +MemTxResult tx; +uint16_t data; + + tx =opb_read (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx);
same
Quoted 203 lines
hw/fsi/opb.c new file +154
-0+ +return data; +} + +uint32_t opb_read32 (OPBus *opb,hwaddr addr) +{ +MemTxResult tx; +uint32_t data; + + tx =opb_read (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx); + +return data; +} + +static MemTxResult opb_write (OPBus *opb,hwaddr addr,void *data,size_t len) +{ +return address_space_write (&opb->as, addr,MEMTXATTRS_UNSPECIFIED , data, + len); +} + +void opb_write8 (OPBus *opb,hwaddr addr,uint8_t data) +{ +MemTxResult tx; + + tx =opb_write (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx); +} + +void opb_write16 (OPBus *opb,hwaddr addr,uint16_t data) +{ +MemTxResult tx; + + tx =opb_write (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx); +} + +void opb_write32 (OPBus *opb,hwaddr addr,uint32_t data) +{ +MemTxResult tx; + + tx =opb_write (opb, addr, &data,sizeof (data)); +/* FIXME: improve error handling */ +assert (!tx); +} + +void opb_fsi_master_address (OPBus *opb,hwaddr addr) +{ +memory_region_transaction_begin (); +memory_region_set_address (&opb->fsi.iomem, addr); +memory_region_transaction_commit (); +} + +void opb_opb2fsi_address (OPBus *opb,hwaddr addr) +{ +memory_region_transaction_begin (); +memory_region_set_address (&opb->fsi.opb2fsi, addr); +memory_region_transaction_commit (); +} + +static uint64_t opb_unimplemented_read (void *opaque,hwaddr addr,unsigned size) +{ +qemu_log_mask (LOG_UNIMP ,"%s: read @0x%" HWADDR_PRIx" size=%d\n" , + __func__, addr, size); + +return 0 ; +} + +static void opb_unimplemented_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +qemu_log_mask (LOG_UNIMP ,"%s: write @0x%" HWADDR_PRIx" size=%d " +"value=%" PRIx64"\n" , __func__, addr, size, data); +} + +static const struct MemoryRegionOps opb_unimplemented_ops = { + .read = opb_unimplemented_read, + .write = opb_unimplemented_write, + .endianness =DEVICE_BIG_ENDIAN , +}; + +static void opb_realize (BusState *bus,Error **errp) +{ +OPBus *opb =OP_BUS (bus); +Error *err =NULL ; + +memory_region_init_io (&opb->mr,OBJECT (opb), &opb_unimplemented_ops, opb, +NULL ,UINT32_MAX ); +address_space_init (&opb->as, &opb->mr,"opb" ); + +object_property_set_bool (OBJECT (&opb->fsi),"realized" , true, &err); +if (err) { +error_propagate (errp, err); +return ; + } +memory_region_add_subregion (&opb->mr,0x80000000 , &opb->fsi.iomem); + +/* OPB2FSI region */ +/* +* Avoid endianness issues by mapping each slave's memory region directly. +* Manually bridging multiple address-spaces causes endian swapping +* headaches as memory_region_dispatch_read() and +* memory_region_dispatch_write() correct the endianness based on the +* target machine endianness and not relative to the device endianness on +* either side of the bridge. +*/ +/* +* XXX: This is a bit hairy and will need to be fixed when I sort out the +* bus/slave relationship and any changes to the CFAM modelling (multiple +* slaves, LBUS) +*/ +memory_region_add_subregion (&opb->mr,0xa0000000 , &opb->fsi.opb2fsi); +} + +static void opb_init (Object *o) +{ +OPBus *opb =OP_BUS (o); + +object_initialize_child (o,"fsi-master" , &opb->fsi,TYPE_FSI_MASTER ); +qdev_set_parent_bus (DEVICE (&opb->fsi),BUS (o), &error_abort); +} + +static void opb_finalize (Object *o) +{ +OPBus *opb =OP_BUS (o); + +address_space_destroy (&opb->as); +} + +static void opb_class_init (ObjectClass *klass,void *data) +{ +BusClass *bc =BUS_CLASS (klass); + bc->realize = opb_realize; +} + +static const TypeInfo opb_info = { + .name =TYPE_OP_BUS , + .parent =TYPE_BUS , + .instance_init = opb_init, + .instance_finalize = opb_finalize, + .instance_size =sizeof (OPBus), + .class_init = opb_class_init, + .class_size =sizeof (OPBusClass), +}; + +static void opb_register_types (void ) +{ +type_register_static (&opb_info); +} + +type_init (opb_register_types);include/hw/fsi/opb.h new file +43
-0@@ -0,0 +1,43 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM On-Chip Peripheral Bus +*/ +#ifndef FSI_OPB_H +#define FSI_OPB_H + +#include "exec/memory.h" +#include "hw/fsi/fsi-master.h" + +#define TYPE_OP_BUS "opb" +OBJECT_DECLARE_SIMPLE_TYPE(OPBus, OP_BUS) + +typedef struct OPBus { +/*< private >*/ +BusState bus; + +/*< public >*/ +MemoryRegion mr; +AddressSpace as; + +/* Model OPB as dumb enough just to provide an address-space */ +/* TODO: Maybe don't store device state in the bus? */ +FSIMasterState fsi; +}OPBus ; + +typedef struct OPBusClass { +BusClass parent_class; +}OPBusClass ; + +uint8_t opb_read8 (OPBus *opb,hwaddr addr); +uint16_t opb_read16 (OPBus *opb,hwaddr addr); +uint32_t opb_read32 (OPBus *opb,hwaddr addr); +void opb_write8 (OPBus *opb,hwaddr addr,uint8_t data); +void opb_write16 (OPBus *opb,hwaddr addr,uint16_t data); +void opb_write32 (OPBus *opb,hwaddr addr,uint32_t data); + +void opb_fsi_master_address (OPBus *opb,hwaddr addr); +void opb_opb2fsi_address (OPBus *opb,hwaddr addr); + +#endif /* FSI_OPB_H */
Re: [PATCH v4 10/10] hw/fsi: Update MAINTAINER list
In reply to Ninad PalsuleQuoted 15 lines · Ninad Palsule
Added maintainer for IBM FSI model
Signed-off-by Ninad Palsule <[email protected]>---
V4:
- Added separate commit for MAINTAINER change.--- MAINTAINERS | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+)MAINTAINERS +0
-0
MAINTAINERS F: tests/qtest/adm1272-test.c · line 3400
Quoted 6 lines
MAINTAINERS +3
-0@@ -3395,6 +3395,28 @@ F: tests/qtest/adm1272-test.c F: tests/qtest/max34451-test.c F: tests/qtest/isl_pmbus_vr-test.c +FSI +M: Ninad Palsule <[email protected]> +S: Maintained
Excellent !
MAINTAINERS F: tests/qtest/adm1272-test.c · line 3408
Quoted 8 lines
MAINTAINERS +8
-0+F: hw/fsi/aspeed-apb2opb.c +F: hw/fsi/cfam.c +F: hw/fsi/fsi.c +F: hw/fsi/fsi-slave.c +F: hw/fsi/opb.c +F: hw/fsi/engine-scratchpad.c +F: hw/fsi/fsi-master.c +F: hw/fsi/lbus.c
This would work the same :
hw/fsi/*include/hw/fsi/*
Quoted 14 lines
MAINTAINERS +11
-0+F: include/hw/fsi/aspeed-apb2opb.h +F: include/hw/fsi/cfam.h +F: include/hw/fsi/fsi.h +F: include/hw/fsi/fsi-slave.h +F: include/hw/fsi/opb.h +F: include/hw/fsi/engine-scratchpad.h +F: include/hw/fsi/fsi-master.h +F: include/hw/fsi/lbus.h +F: docs/specs/fsi.rst +F: tests/qtest/fsi-test.c + Firmware schema specifications M: Philippe Mathieu-Daudé <[email protected]> R: Daniel P. Berrange <[email protected]>
Re: [PATCH v4 06/10] hw/fsi: Aspeed APB2OPB interface
In reply to Ninad PalsuleQuoted 69 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated review comments by Joel
v3:
- Incorporated review comments by Thomas Huth
v4:
- Compile FSI withASPEED_SOConly.--- hw/arm/Kconfig | 1 + hw/fsi/Kconfig | 20 +- hw/fsi/aspeed-apb2opb.c | 352 ++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 9 +- hw/fsi/trace-events | 3 +- hw/fsi/trace.h | 1 + include/hw/fsi/aspeed-apb2opb.h | 33 +++ meson.build | 1 + 8 files changed, 407 insertions(+), 13 deletions(-)create mode 100644
hw/fsi/aspeed-apb2opb.ccreate mode 100644hw/fsi/trace.h
create mode 100644include/hw/fsi/aspeed-apb2opb.hhw/arm/Kconfig +1
-0@@ -555,6 +555,7 @@ config ASPEED_SOC select LED select PMBUS select MAX31785 + select FSI_APB2OPB_ASPEED config MPS2 boolhw/fsi/Kconfig +9
-5@@ -1,19 +1,23 @@ -config OPB +config FSI_APB2OPB_ASPEED bool - select CFAM + select FSI_OPB -config CFAM +config FSI_OPB + bool + select FSI_CFAM + +config FSI_CFAM bool select FSI - select SCRATCHPAD - select LBUS + select FSI_SCRATCHPAD + select FSI_LBUS config FSI bool
hw/fsi/Kconfig line 23
Quoted 10 lines
hw/fsi/Kconfig +3
-3-config SCRATCHPAD +config FSI_SCRATCHPAD bool - select LBUS + select FSI_LBUS -config LBUS +config FSI_LBUS bool
Some of these changes belong to another patch.
Quoted 152 lines
hw/fsi/aspeed-apb2opb.c new file +146
-0@@ -0,0 +1,352 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* ASPEED APB-OPB FSI interface +*/ + +#include "qemu/osdep.h" +#include "qemu/log.h" +#include "qom/object.h" +#include "qapi/error.h" +#include "trace.h" + +#include "hw/fsi/aspeed-apb2opb.h" +#include "hw/qdev-core.h" + +#define TO_REG (x) (x >> 2) +#define GENMASK (t, b) (((1ULL << ((t) + 1)) - 1) & ~((1ULL << (b)) - 1)) + +#define APB2OPB_VERSION TO_REG(0x00) +#define APB2OPB_VERSION_VER GENMASK(7, 0) + +#define APB2OPB_TRIGGER TO_REG(0x04) +#define APB2OPB_TRIGGER_EN BIT(0) + +#define APB2OPB_CONTROL TO_REG(0x08) +#define APB2OPB_CONTROL_OFF GENMASK(31, 13) + +#define APB2OPB_OPB2FSI TO_REG(0x0c) +#define APB2OPB_OPB2FSI_OFF GENMASK(31, 22) + +#define APB2OPB_OPB0_SEL TO_REG(0x10) +#define APB2OPB_OPB1_SEL TO_REG(0x28) +#define APB2OPB_OPB_SEL_EN BIT(0) + +#define APB2OPB_OPB0_MODE TO_REG(0x14) +#define APB2OPB_OPB1_MODE TO_REG(0x2c) +#define APB2OPB_OPB_MODE_RD BIT(0) + +#define APB2OPB_OPB0_XFER TO_REG(0x18) +#define APB2OPB_OPB1_XFER TO_REG(0x30) +#define APB2OPB_OPB_XFER_FULL BIT(1) +#define APB2OPB_OPB_XFER_HALF BIT(0) + +#define APB2OPB_OPB0_ADDR TO_REG(0x1c) +#define APB2OPB_OPB0_WRITE_DATA TO_REG(0x20) + +#define APB2OPB_OPB1_DMA_EN TO_REG(0x24) +#define APB2OPB_OPB1_DMA_EN_3 BIT(3) +#define APB2OPB_OPB1_DMA_EN_2 BIT(2) +#define APB2OPB_OPB1_DMA_EN_1 BIT(1) +#define APB2OPB_OPB1_DMA_EN_0 BIT(0) + +#define APB2OPB_OPB1_ADDR TO_REG(0x34) +#define APB2OPB_OPB1_WRITE_DATA TO_REG(0x38) + +#define APB2OPB_OPB_CLK TO_REG(0x3c) +#define APB2OPB_OPB_CLK_SYNC BIT(0) + +#define APB2OPB_IRQ_CLEAR TO_REG(0x40) +#define APB2OPB_IRQ_CLEAR_EN BIT(0) + +#define APB2OPB_IRQ_MASK TO_REG(0x44) +#define APB2OPB_IRQ_MASK_OPB1_TX_ACK BIT(17) +#define APB2OPB_IRQ_MASK_OPB0_TX_ACK BIT(16) +#define APB2OPB_IRQ_MASK_CH3_TCONT BIT(15) +#define APB2OPB_IRQ_MASK_CH2_TCONT BIT(14) +#define APB2OPB_IRQ_MASK_CH1_TCONT BIT(13) +#define APB2OPB_IRQ_MASK_CH0_TCONT BIT(12) +#define APB2OPB_IRQ_MASK_CH3_FIFO_EMPTY BIT(11) +#define APB2OPB_IRQ_MASK_CH2_FIFO_EMPTY BIT(10) +#define APB2OPB_IRQ_MASK_CH1_FIFO_EMPTY BIT(9) +#define APB2OPB_IRQ_MASK_CH0_FIFO_EMPTY BIT(8) +#define APB2OPB_IRQ_MASK_CH3_FIFO_FULL BIT(7) +#define APB2OPB_IRQ_MASK_CH2_FIFO_FULL BIT(6) +#define APB2OPB_IRQ_MASK_CH1_FIFO_FULL BIT(5) +#define APB2OPB_IRQ_MASK_CH0_FIFO_FULL BIT(4) +#define APB2OPB_IRQ_MASK_CH3_DMA_EOT BIT(3) +#define APB2OPB_IRQ_MASK_CH2_DMA_EOT BIT(2) +#define APB2OPB_IRQ_MASK_CH1_DMA_EOT BIT(1) +#define APB2OPB_IRQ_MASK_CH0_DMA_EOT BIT(0) + +#define APB2OPB_IRQ_STS TO_REG(0x48) +#define APB2OPB_IRQ_STS_MASTER_ERROR BIT(28) +#define APB2OPB_IRQ_STS_PORT_ERROR BIT(27) +#define APB2OPB_IRQ_STS_HOTPLUG BIT(26) +#define APB2OPB_IRQ_STS_SLAVE_7 BIT(25) +#define APB2OPB_IRQ_STS_SLAVE_6 BIT(24) +#define APB2OPB_IRQ_STS_SLAVE_5 BIT(23) +#define APB2OPB_IRQ_STS_SLAVE_4 BIT(22) +#define APB2OPB_IRQ_STS_SLAVE_3 BIT(21) +#define APB2OPB_IRQ_STS_SLAVE_2 BIT(20) +#define APB2OPB_IRQ_STS_SLAVE_1 BIT(19) +#define APB2OPB_IRQ_STS_SLAVE_0 BIT(18) +#define APB2OPB_IRQ_STS_OPB1_TX_ACK BIT(17) +#define APB2OPB_IRQ_STS_OPB0_TX_ACK BIT(16) +#define APB2OPB_IRQ_STS_CH3_TCONT BIT(15) +#define APB2OPB_IRQ_STS_CH2_TCONT BIT(14) +#define APB2OPB_IRQ_STS_CH1_TCONT BIT(13) +#define APB2OPB_IRQ_STS_CH0_TCONT BIT(12) +#define APB2OPB_IRQ_STS_CH3_FIFO_EMPTY BIT(11) +#define APB2OPB_IRQ_STS_CH2_FIFO_EMPTY BIT(10) +#define APB2OPB_IRQ_STS_CH1_FIFO_EMPTY BIT(9) +#define APB2OPB_IRQ_STS_CH0_FIFO_EMPTY BIT(8) +#define APB2OPB_IRQ_STS_CH3_FIFO_FULL BIT(7) +#define APB2OPB_IRQ_STS_CH2_FIFO_FULL BIT(6) +#define APB2OPB_IRQ_STS_CH1_FIFO_FULL BIT(5) +#define APB2OPB_IRQ_STS_CH0_FIFO_FULL BIT(4) +#define APB2OPB_IRQ_STS_CH3_DMA_EOT BIT(3) +#define APB2OPB_IRQ_STS_CH2_DMA_EOT BIT(2) +#define APB2OPB_IRQ_STS_CH1_DMA_EOT BIT(1) +#define APB2OPB_IRQ_STS_CH0_DMA_EOT BIT(0) + +#define APB2OPB_OPB0_WRITE_WORD_ENDIAN TO_REG(0x4c) +#define APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE 0x0011101b +#define APB2OPB_OPB0_WRITE_BYTE_ENDIAN TO_REG(0x50) +#define APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE 0x0c330f3f +#define APB2OPB_OPB1_WRITE_WORD_ENDIAN TO_REG(0x54) +#define APB2OPB_OPB1_WRITE_BYTE_ENDIAN TO_REG(0x58) +#define APB2OPB_OPB0_READ_BYTE_ENDIAN TO_REG(0x5c) +#define APB2OPB_OPB0_READ_WORD_ENDIAN_BE 0x00030b1b +#define APB2OPB_OPB1_READ_BYTE_ENDIAN TO_REG(0x60) + +#define APB2OPB_RETRY TO_REG(0x64) +#define APB2OPB_RETRY_COUNTER GENMASK(15, 0) + +#define APB2OPB_OPB0_STATUS TO_REG(0x80) +#define APB2OPB_OPB1_STATUS TO_REG(0x8c) +#define APB2OPB_OPB_STATUS_TIMEOUT BIT(4) +#define APB2OPB_OPB_STATUS_RETRY BIT(3) +#define APB2OPB_OPB_STATUS_ERROR_ACK BIT(2) +#define APB2OPB_OPB_STATUS_FW_ACK BIT(1) +#define APB2OPB_OPB_STATUS_HW_ACK BIT(0) + +#define APB2OPB_OPB0_READ_DATA TO_REG(0x84) + +#define APB2OPB_OPB1_DMA_STATUS TO_REG(0x88) +#define APB2OPB_OPB1_DMA_STATUS_CH3_EOT BIT(7) +#define APB2OPB_OPB1_DMA_STATUS_CH2_EOT BIT(6) +#define APB2OPB_OPB1_DMA_STATUS_CH1_EOT BIT(5) +#define APB2OPB_OPB1_DMA_STATUS_CH0_EOT BIT(4) +#define APB2OPB_OPB1_DMA_STATUS_CH3_REQ BIT(3) +#define APB2OPB_OPB1_DMA_STATUS_CH2_REQ BIT(2) +#define APB2OPB_OPB1_DMA_STATUS_CH1_REQ BIT(1) +#define APB2OPB_OPB1_DMA_STATUS_CH0_REQ BIT(0) +
hw/fsi/aspeed-apb2opb.c line 156
Quoted 10 lines
hw/fsi/aspeed-apb2opb.c new file +10
-0+#define APB2OPB_OPB1_READ_DATA TO_REG(0x90) + +static uint64_t aspeed_apb2opb_read (void *opaque,hwaddr addr,unsigned size) +{ +AspeedAPB2OPBState *s =ASPEED_APB2OPB (opaque); + +trace_aspeed_apb2opb_read (addr, size); + +assert (!(addr &3 )); +assert (size ==4 );
please fix the MemoryRegionOps definition instead.
Quoted 281 lines
hw/fsi/aspeed-apb2opb.c new file +196
-0+ +if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds read: 0x%" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return 0 ; + } + +return s->regs[TO_REG (addr)]; +} + +static void aspeed_apb2opb_write (void *opaque,hwaddr addr,uint64_t data, +unsigned size) +{ +AspeedAPB2OPBState *s =ASPEED_APB2OPB (opaque); + +trace_aspeed_apb2opb_write (addr, size, data); + +assert (!(addr &3 )); +assert (size ==4 ); + +if (addr + size >sizeof (s->regs)) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Out of bounds write: %" HWADDR_PRIx" for %u\n" , + __func__, addr, size); +return ; + } + +switch (TO_REG (addr)) { +case APB2OPB_CONTROL : +opb_fsi_master_address (&s->opb[0 ], data &APB2OPB_CONTROL_OFF ); +break ; +case APB2OPB_OPB2FSI : +opb_opb2fsi_address (&s->opb[0 ], data &APB2OPB_OPB2FSI_OFF ); +break ; +case APB2OPB_OPB0_WRITE_WORD_ENDIAN : +if (data !=APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE ) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bridge needs to be driven as BE (0x%x)\n" , + __func__,APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE ); + } +break ; +case APB2OPB_OPB0_WRITE_BYTE_ENDIAN : +if (data !=APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE ) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bridge needs to be driven as BE (0x%x)\n" , + __func__,APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE ); + } +break ; +case APB2OPB_OPB0_READ_BYTE_ENDIAN : +if (data !=APB2OPB_OPB0_READ_WORD_ENDIAN_BE ) { +qemu_log_mask (LOG_GUEST_ERROR , +"%s: Bridge needs to be driven as BE (0x%x)\n" , + __func__,APB2OPB_OPB0_READ_WORD_ENDIAN_BE ); + } +break ; +case APB2OPB_TRIGGER : + { +uint32_t opb, op_mode, op_size, op_addr, op_data; + +assert ((s->regs[APB2OPB_OPB0_SEL ] &APB2OPB_OPB_SEL_EN ) ^ + (s->regs[APB2OPB_OPB1_SEL ] &APB2OPB_OPB_SEL_EN )); + +if (s->regs[APB2OPB_OPB0_SEL ] &APB2OPB_OPB_SEL_EN ) { + opb =0 ; + op_mode = s->regs[APB2OPB_OPB0_MODE ]; + op_size = s->regs[APB2OPB_OPB0_XFER ]; + op_addr = s->regs[APB2OPB_OPB0_ADDR ]; + op_data = s->regs[APB2OPB_OPB0_WRITE_DATA ]; + }else if (s->regs[APB2OPB_OPB1_SEL ] &APB2OPB_OPB_SEL_EN ) { + opb =1 ; + op_mode = s->regs[APB2OPB_OPB1_MODE ]; + op_size = s->regs[APB2OPB_OPB1_XFER ]; + op_addr = s->regs[APB2OPB_OPB1_ADDR ]; + op_data = s->regs[APB2OPB_OPB1_WRITE_DATA ]; + }else { +g_assert_not_reached (); + } + +if (op_size & ~(APB2OPB_OPB_XFER_HALF |APB2OPB_OPB_XFER_FULL )) { +qemu_log_mask (LOG_GUEST_ERROR , +"OPB transaction failed: Unrecognised access width: %d\n" , + op_size); +return ; + } + + op_size +=1 ; + +if (op_mode &APB2OPB_OPB_MODE_RD ) { +int index = opb ?APB2OPB_OPB1_READ_DATA + :APB2OPB_OPB0_READ_DATA ; + +switch (op_size) { +case 1 : + s->regs[index] =opb_read8 (&s->opb[opb], op_addr); +break ; +case 2 : + s->regs[index] =opb_read16 (&s->opb[opb], op_addr); +break ; +case 4 : + s->regs[index] =opb_read32 (&s->opb[opb], op_addr); +break ; +default : +g_assert_not_reached ();/* should have bailed above */ + } + }else { +/* FIXME: Endian swizzling */ +switch (op_size) { +case 1 : +opb_write8 (&s->opb[opb], op_addr, op_data); +break ; +case 2 : +opb_write16 (&s->opb[opb], op_addr, op_data); +break ; +case 4 : +opb_write32 (&s->opb[opb], op_addr, op_data); +break ; +default : +g_assert_not_reached ();/* should have bailed above */ + } + } + s->regs[APB2OPB_IRQ_STS ] |= opb ?APB2OPB_IRQ_STS_OPB1_TX_ACK + :APB2OPB_IRQ_STS_OPB0_TX_ACK ; +break ; + } + } + + s->regs[TO_REG (addr)] = data; +} + +static const struct MemoryRegionOps aspeed_apb2opb_ops = { + .read = aspeed_apb2opb_read, + .write = aspeed_apb2opb_write, + .endianness =DEVICE_LITTLE_ENDIAN , +}; + +static void aspeed_apb2opb_realize (DeviceState *dev,Error **errp) +{ +SysBusDevice *sbd =SYS_BUS_DEVICE (dev); +AspeedAPB2OPBState *s =ASPEED_APB2OPB (dev); + +qbus_init (&s->opb[0 ],sizeof (s->opb[0 ]),TYPE_OP_BUS , +DEVICE (s),NULL ); +qbus_init (&s->opb[1 ],sizeof (s->opb[1 ]),TYPE_OP_BUS , +DEVICE (s),NULL ); + +sysbus_init_irq (sbd, &s->irq); + +memory_region_init_io (&s->iomem,OBJECT (s), &aspeed_apb2opb_ops, s, +TYPE_ASPEED_APB2OPB ,0x1000 ); +sysbus_init_mmio (sbd, &s->iomem); +} + +static void aspeed_apb2opb_reset (DeviceState *dev) +{ +AspeedAPB2OPBState *s =ASPEED_APB2OPB (dev); + +memset (s->regs,0 ,sizeof (s->regs)); + + s->regs[APB2OPB_VERSION ] =0x000000a1 ; + +/* +* The following magic values came from AST2600 data sheet +* The register values are defined under section "FSI controller" +* as initial values. +*/ + s->regs[APB2OPB_OPB0_WRITE_WORD_ENDIAN ] =0x0044eee4 ; + s->regs[APB2OPB_OPB0_WRITE_BYTE_ENDIAN ] =0x0055aaff ; + s->regs[APB2OPB_OPB1_WRITE_WORD_ENDIAN ] =0x00117717 ; + s->regs[APB2OPB_OPB1_WRITE_BYTE_ENDIAN ] =0xffaa5500 ; + s->regs[APB2OPB_OPB0_READ_BYTE_ENDIAN ] =0x0044eee4 ; + s->regs[APB2OPB_OPB0_READ_BYTE_ENDIAN ] =0x00117717 ; +} + +static void aspeed_apb2opb_class_init (ObjectClass *klass,void *data) +{ +DeviceClass *dc =DEVICE_CLASS (klass); + + dc->desc ="ASPEED APB2OPB Bridge" ; + dc->realize = aspeed_apb2opb_realize; + dc->reset = aspeed_apb2opb_reset; +} + +static const TypeInfo aspeed_apb2opb_info = { + .name =TYPE_ASPEED_APB2OPB , + .parent =TYPE_SYS_BUS_DEVICE , + .instance_size =sizeof (AspeedAPB2OPBState), + .class_init = aspeed_apb2opb_class_init, +}; + +static void aspeed_apb2opb_register_types (void ) +{ +type_register_static (&aspeed_apb2opb_info); +} + +type_init (aspeed_apb2opb_register_types);hw/fsi/meson.build +5
-4@@ -1,5 +1,6 @@ -system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) -system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) -system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_FSI_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_FSI_CFAM', if_true: files('cfam.c')) system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c')) -system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_APB2OPB_ASPEED', if_true: files('aspeed-apb2opb.c'))hw/fsi/trace-events +2
-1@@ -1,5 +1,6 @@ cfam_config_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" cfam_config_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 - cfam_unimplemented_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" cfam_unimplemented_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64 +aspeed_apb2opb_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +aspeed_apb2opb_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64hw/fsi/trace.h new file +1
-0@@ -0,0 +1 @@ +#include "trace/trace-hw_fsi.h" include/hw/fsi/aspeed-apb2opb.h new file +33
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* ASPEED APB2OPB Bridge +*/ +#ifndef FSI_ASPEED_APB2OPB_H +#define FSI_ASPEED_APB2OPB_H + +#include "hw/sysbus.h" +#include "hw/fsi/opb.h" + +#define TYPE_ASPEED_APB2OPB "aspeed.apb2opb" +OBJECT_DECLARE_SIMPLE_TYPE(AspeedAPB2OPBState, ASPEED_APB2OPB) + +#define ASPEED_APB2OPB_NR_REGS ((0xe8 >> 2) + 1) + +#define ASPEED_FSI_NUM 2 + +typedef struct AspeedAPB2OPBState { +/*< private >*/ +SysBusDevice parent_obj; + +/*< public >*/ +MemoryRegion iomem; + +uint32_t regs[ASPEED_APB2OPB_NR_REGS ]; +qemu_irq irq; + +OPBus opb[ASPEED_FSI_NUM ]; +}AspeedAPB2OPBState ; + +#endif /* FSI_ASPEED_APB2OPB_H */ meson.build +1
-0@@ -3244,6 +3244,7 @@ if have_system 'hw/char', 'hw/display', 'hw/dma', + 'hw/fsi', 'hw/hyperv', 'hw/i2c', 'hw/i386',
Re: [PATCH v4 07/10] hw/arm: Hook up FSI module in AST2600
In reply to Ninad PalsuleQuoted 96 lines · Ninad Palsule
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service processor access to the internal buses of a host POWER processor to perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage, including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on buses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for a CFAM to be simultaneously driven from multiple FSI links. The modeling is not so complete; it's assumed that each CFAM is attached to a single FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This is not necessary to get FSI off the ground thanks to the mapping of the CFAM address space onto the OPB address space - the models follow this directly and map the CFAM memory region into the OPB's memory region. Future work includes supporting more advanced accesses that drive the FSI master directly rather than indirectly via the CFAM mapping, which will require implementing the FSI state machine and methods for each of the FSI symbols on the slave. Further down the track we can also look at supporting the bitbanged SoftFSI drivers in Linux by extending the FSI slave model to resolve sequences of GPIO IRQs into FSI symbols, and calling the associated symbol method on the slave to map the access onto the CFAM.
Testing:
Quoted 8 lines
Tested by reading cfam config address 0 on rainier machine type. root@p10bmc:~# pdbg -a getcfam 0x0 p0: 0x0 = 0xc0022d15Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>
you might want to add a specific fsi realize routine if extra devices need to be realized at the board level.
Thanks,
C.
Quoted 85 lines
--- hw/arm/aspeed_ast2600.c | 19 +++++++++++++++++++ include/hw/arm/aspeed_soc.h | 4 ++++ 2 files changed, 23 insertions(+)hw/arm/aspeed_ast2600.c +19
-0@@ -75,6 +75,8 @@ static const hwaddr aspeed_soc_ast2600_memmap[] = { [ASPEED_DEV_UART12] = 0x1E790600, [ASPEED_DEV_UART13] = 0x1E790700, [ASPEED_DEV_VUART] = 0x1E787000, + [ASPEED_DEV_FSI1] = 0x1E79B000, + [ASPEED_DEV_FSI2] = 0x1E79B100, [ASPEED_DEV_I3C] = 0x1E7A0000, [ASPEED_DEV_SDRAM] = 0x80000000, };@@ -132,6 +134,8 @@ static const int aspeed_soc_ast2600_irqmap[] = { [ASPEED_DEV_ETH4] = 33, [ASPEED_DEV_KCS] = 138, /* 138 -> 142 */ [ASPEED_DEV_DP] = 62, + [ASPEED_DEV_FSI1] = 100, + [ASPEED_DEV_FSI2] = 101, [ASPEED_DEV_I3C] = 102, /* 102 -> 107 */ };@@ -262,6 +266,10 @@ static void aspeed_soc_ast2600_init(Object *obj)object_initialize_child (obj,"emmc-boot-controller" , &s->emmc_boot_controller,TYPE_UNIMPLEMENTED_DEVICE ); + +for (i =0 ; i <ASPEED_FSI_NUM ; i++) { +object_initialize_child (obj,"fsi[*]" , &s->fsi[i],TYPE_ASPEED_APB2OPB ); + } }/* @@ -622,6 +630,17 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)return ; }aspeed_mmio_map (s,SYS_BUS_DEVICE (&s->sbc),0 , sc->memmap[ASPEED_DEV_SBC ]); + +/* FSI */ +for (i =0 ; i <ASPEED_FSI_NUM ; i++) { +if (!sysbus_realize (SYS_BUS_DEVICE (&s->fsi[i]), errp)) { +return ; + } +aspeed_mmio_map (s,SYS_BUS_DEVICE (&s->fsi[i]),0 , + sc->memmap[ASPEED_DEV_FSI1 + i]); +sysbus_connect_irq (SYS_BUS_DEVICE (&s->fsi[i]),0 , +aspeed_soc_get_irq (s,ASPEED_DEV_FSI1 + i)); + } }static void aspeed_soc_ast2600_class_init (ObjectClass *oc,void *data)include/hw/arm/aspeed_soc.h +4
-0@@ -36,6 +36,7 @@#include "hw/misc/aspeed_lpc.h" #include "hw/misc/unimp.h" #include "hw/misc/aspeed_peci.h" +#include "hw/fsi/aspeed-apb2opb.h" #include "hw/char/serial.h" #define ASPEED_SPIS_NUM 2@@ -96,6 +97,7 @@ struct AspeedSoCState {UnimplementedDeviceState udc;UnimplementedDeviceState sgpiom;UnimplementedDeviceState jtag[ASPEED_JTAG_NUM ]; +AspeedAPB2OPBState fsi[2 ]; };#define TYPE_ASPEED_SOC "aspeed-soc"@@ -191,6 +193,8 @@ enum {ASPEED_DEV_SGPIOM ,ASPEED_DEV_JTAG0 ,ASPEED_DEV_JTAG1 , +ASPEED_DEV_FSI1 , + ASPEED_DEV_FSI2, };#define ASPEED_SOC_SPI_BOOT_ADDR 0x0
Re: [PATCH v4 01/10] hw/fsi: Introduce IBM's Local bus
In reply to Cédric Le GoaterHello Cederic,
Quoted 20 lines · Cédric Le Goater
Quoted 10 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
Quoted 7 lines
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
---
Quoted 3 lines
It is nice to have the header files upfront.
orderFile = /path/to/qemu/scripts/git.orderfile
ok, Done. Thanks. I wasn't aware of this.
Quoted 58 lines
Quoted 58 lines
hw/Kconfig | 1 +
hw/fsi/Kconfig | 2 +
hw/fsi/lbus.c | 94 +++++++++++++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 +
hw/meson.build | 1 +
include/hw/fsi/lbus.h| 48 ++++++++++++++++++++++include/qemu/bitops.h| 6 +++7 files changed, 153 insertions(+)create mode 100644 hw/fsi/Kconfig
create mode 100644hw/fsi/lbus.c
create mode 100644 hw/fsi/meson.build
create mode 100644include/hw/fsi/lbus.hhw/Kconfig +0
-0@@ -9,6 +9,7 @@ source core/Kconfigsource cxl/Kconfig
source display/Kconfig
source dma/Kconfig
+source fsi/Kconfig
source gpio/Kconfig
source hyperv/Kconfig
source i2c/Kconfighw/fsi/Kconfig new file +2
-0@@ -0,0 +1,2 @@ +config LBUS + boolhw/fsi/lbus.c new file +17
-0@@ -0,0 +1,94 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Local bus where FSI slaves are connected +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/lbus.h" + +#include "hw/qdev-properties.h" + +static void lbus_realize (BusState *bus,Error **errp)
Quoted 8 lines
hw/fsi/lbus.c line 23
Quoted 6 lines
hw/fsi/lbus.c new file +6
-0+{ + LBusNode *node; + LBus *lbus = LBUS(bus); + + memory_region_init(&lbus->mr, OBJECT(lbus), TYPE_LBUS, + (2 * 1024 * 1024) - 0x400);please use some define
Added defines.
Quoted 14 lines
hw/fsi/lbus.c line 34
Quoted 12 lines
hw/fsi/lbus.c new file +11
-0+ + QLIST_FOREACH(node, &lbus->devices, next) { + memory_region_add_subregion(&lbus->mr, node->ldev->address, + &node->ldev->iomem); + } +} + +static void lbus_init (Object *o) +{ +} +please remove if unused
Removed.
Quoted 24 lines
Quoted 24 lines
hw/fsi/lbus.c new file +20
-0+static void lbus_class_init (ObjectClass *klass,void *data) +{ + BusClass *k = BUS_CLASS(klass); + k->realize = lbus_realize; +} + +static const TypeInfo lbus_info = { + .name = TYPE_LBUS, + .parent = TYPE_BUS, + .instance_init = lbus_init, + .instance_size = sizeof(LBus), + .class_init = lbus_class_init, +}; + +static Property lbus_device_props[] = { + DEFINE_PROP_UINT32("address", LBusDevice, address, 0), + DEFINE_PROP_END_OF_LIST(), +}; + +DeviceState *lbus_create_device(LBus *bus, const char *type,
uint32_taddr)
+{
Quoted 8 lines
Quoted 6 lines
+ DeviceState *dev;
+ LBusNode *node;
+
+ dev =qdev_new(type);
+qdev_prop_set_uint8(dev, "address", addr);
+qdev_realize_and_unref(dev, &bus->bus, &error_fatal);BUS(bus) ?
Fixed
Quoted 8 lines
Quoted 6 lines
+
+ /* Move topost_load*/
+ node =g_malloc(sizeof(struct LBusNode)); +node->ldev=LBUS_DEVICE(dev);
+QLIST_INSERT_HEAD(&bus->devices, node, next);This list looks useless to me.
This list is used to add new devices. Keeping it for now.
Quoted 62 lines
Quoted 62 lines
+ return dev;
hw/fsi/lbus.c new file +26
-0+} + +static void lbus_device_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->bus_type = TYPE_LBUS; + device_class_set_props(dc, lbus_device_props); +} + +static const TypeInfo lbus_device_type_info = { + .name = TYPE_LBUS_DEVICE, + .parent = TYPE_DEVICE, + .instance_size = sizeof(LBusDevice), + .abstract = true, + .class_init = lbus_device_class_init, + .class_size = sizeof(LBusDeviceClass), +}; + +static void lbus_register_types (void ) +{ + type_register_static(&lbus_info); + type_register_static(&lbus_device_type_info); +} + +type_init (lbus_register_types);hw/fsi/meson.build new file +1
-0@@ -0,0 +1 @@ +system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c'))hw/meson.build +1
-0@@ -43,6 +43,7 @@ subdir('virtio') subdir('watchdog') subdir('xen') subdir('xenpv') +subdir('fsi') subdir('alpha') subdir('arm')include/hw/fsi/lbus.h new file +10
-0@@ -0,0 +1,48 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Local bus and connected device structures. +*/ +#ifndef FSI_LBUS_H +#define FSI_LBUS_H + +#include "exec/memory.h"
Quoted 8 lines
include/hw/fsi/lbus.h line 14
Quoted 5 lines
include/hw/fsi/lbus.h new file +4
-0+#include "hw/qdev-core.h" + +#define TYPE_LBUS_DEVICE "lbus.device" +OBJECT_DECLARE_TYPE (LBusDevice, LBusDeviceClass,LBUS_DEVICE )Using an "fsi/FSI" prefix for all definitions seems like a good idea to avoid namespace conflicts.
Added FSI prefix.
Quoted 23 lines
Quoted 23 lines
include/hw/fsi/lbus.h new file +22
-0+typedef struct LBusDevice { + DeviceState parent; + + MemoryRegion iomem; + uint32_t address; +}LBusDevice ; + +typedef struct LBusDeviceClass { + DeviceClass parent; + + uint32_t config; +}LBusDeviceClass ; + +typedef struct LBusNode { + LBusDevice *ldev; + + QLIST_ENTRY(LBusNode) next; +}LBusNode ; + +#define TYPE_LBUS "lbus" +OBJECT_DECLARE_SIMPLE_TYPE (LBus,LBUS ) +
Quoted 8 lines
include/hw/fsi/lbus.h line 43
Quoted 6 lines
include/hw/fsi/lbus.h new file +6
-0+typedef struct LBus { + BusState bus; + + MemoryRegion mr; + + QLIST_HEAD(, LBusNode) devices;BusState already has a list. I think this needs to be reworked.
The list in BusState is for the buses. This list is for devices.
Quoted 16 lines
Quoted 16 lines
include/hw/fsi/lbus.h new file +3
-0+} LBus; + +DeviceState *lbus_create_device(LBus *bus, const char *type,
uint32_taddr);include/hw/fsi/lbus.h new file +2
-0+int lbus_add_device (LBus *bus,LBusDevice *dev); +#endif /* FSI_LBUS_H */ include/qemu/bitops.h +0
-0@@ -618,4 +618,10 @@ static inline uint64_t half_unshuffle64(uint64_t x) return x; }+/* Bitwise operations at the word level. */
Quoted 8 lines
Quoted 5 lines
include/qemu/bitops.h +4
-0+#define BE_BIT (x) BIT(31 - (x)) +#define GENMASK (t, b) \ + (((1ULL << ((t) + 1)) - 1) & ~((1ULL << (b)) - 1)) +#define BE_GENMASK (t, b) GENMASK(BE_BIT(t),
BE_BIT(b))I think we should rework the code to make these macro local to the fsi subsystem, in the
fsi.hfile, or even better get rid of them.
OK, Removed it from bitops.h
Thanks for the review.
~ Ninad
Quoted 8 lines
Thanks,
C.
Quoted 1 line
#endif
Re: [PATCH v4 10/10] hw/fsi: Update MAINTAINER list
In reply to Cédric Le GoaterHello Cedric,
Quoted 11 lines · Cédric Le Goater
Quoted 10 lines · Ninad Palsule
Added maintainer for IBM FSI model
Signed-off-by Ninad Palsule <[email protected]>---
V4:
- Added separate commit for MAINTAINER change.
---
MAINTAINERS| 22 ++++++++++++++++++++++1 file changed, 22 insertions(+)
Quoted 12 lines
MAINTAINERS F: tests/qtest/adm1272-test.c · line 3400
Quoted 10 lines
MAINTAINERS +0
-0@@ -3395,6 +3395,28 @@ F: tests/qtest/adm1272-test.cF:
tests/qtest/max34451-test.c
F:tests/qtest/isl_pmbus_vr-test.c
+FSIMAINTAINERS +2
-0+M: Ninad Palsule <[email protected]> +S: MaintainedExcellent !
Thanks!
Quoted 12 lines
MAINTAINERS F: tests/qtest/adm1272-test.c · line 3408
Quoted 9 lines
MAINTAINERS +8
-0+F: hw/fsi/aspeed-apb2opb.c +F: hw/fsi/cfam.c +F: hw/fsi/fsi.c +F: hw/fsi/fsi-slave.c +F: hw/fsi/opb.c +F: hw/fsi/engine-scratchpad.c +F: hw/fsi/fsi-master.c +F: hw/fsi/lbus.cThis would work the same :
Quoted 2 lines
hw/fsi/*
include/hw/fsi/*
Fixed.
Thanks for the review.
~ Ninad
Quoted 16 lines
Quoted 15 lines
MAINTAINERS +11
-0+F: include/hw/fsi/aspeed-apb2opb.h +F: include/hw/fsi/cfam.h +F: include/hw/fsi/fsi.h +F: include/hw/fsi/fsi-slave.h +F: include/hw/fsi/opb.h +F: include/hw/fsi/engine-scratchpad.h +F: include/hw/fsi/fsi-master.h +F: include/hw/fsi/lbus.h +F: docs/specs/fsi.rst +F: tests/qtest/fsi-test.c +Firmware schema specifications
M: Philippe Mathieu-Daudé <[email protected]>
R: Daniel P. Berrange <[email protected]>
Re: [PATCH v4 02/10] hw/fsi: Introduce IBM's scratchpad
In reply to Cédric Le GoaterHello Cedric,
Quoted 7 lines · Cédric Le Goater
Quoted 4 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS device is embeded inside the scratchpad. The scratchpad
embedded
Fixed
Quoted 52 lines
Quoted 52 lines
provides a non-functional registers. There is a 1-1 relation between scratchpad and LBUS devices. Each LBUS device has 1K memory mapped in the LBUS.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
---
hw/fsi/Kconfig | 4 ++ hw/fsi/engine-scratchpad.c | 100 +++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 +include/hw/fsi/engine-scratchpad.h| 33 ++++++++++4 files changed, 138 insertions(+)create mode 100644
hw/fsi/engine-scratchpad.ccreate mode 100644include/hw/fsi/engine-scratchpad.hhw/fsi/Kconfig +4
-0@@ -1,2 +1,6 @@ +config SCRATCHPAD + bool + select LBUS +config LBUS
boolhw/fsi/engine-scratchpad.c new file +15
-0@@ -0,0 +1,100 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engine +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/engine-scratchpad.h" + +static uint64_t scratchpad_read(void *opaque, hwaddr addr, unsigned
Quoted 8 lines
hw/fsi/engine-scratchpad.c line 20
Quoted 6 lines
size)
hw/fsi/engine-scratchpad.c new file +5
-0+{ + ScratchPad *s = SCRATCHPAD(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: read @0x%" HWADDR_PRIx " size=%d\n", + __func__, addr, size);This should be a trace event. The comment applies to all similar usage.
Fixed all required places.
Quoted 11 lines
Quoted 8 lines
+
+ if (addr) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds read: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return 0;if the MMIO region is correctly sized, this should not be necessary. Do you plans to add support for registers ?
If required I am going to implement registers. Current plan is to get initial changes in and then add more stuff.
Quoted 15 lines
hw/fsi/engine-scratchpad.c line 38
Quoted 13 lines
+ }
hw/fsi/engine-scratchpad.c new file +11
-0+ + return s->reg; +} + +static void scratchpad_write (void *opaque,hwaddr addr,uint64_t data, + unsigned size) +{ + ScratchPad *s = SCRATCHPAD(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: write @0x%" HWADDR_PRIx " size=%d " + "value=%"PRIx64"\n", __func__, addr, size, data);trace event
Fixed
Quoted 42 lines
Quoted 42 lines
+
+ if (addr) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds write: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return;
+ }hw/fsi/engine-scratchpad.c new file +33
-0+ + s->reg = data; +} + +static const struct MemoryRegionOps scratchpad_ops = { + .read = scratchpad_read, + .write = scratchpad_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void scratchpad_realize (DeviceState *dev,Error **errp) +{ + LBusDevice *ldev = LBUS_DEVICE(dev); + + memory_region_init_io(&ldev->iomem, OBJECT(ldev), &scratchpad_ops, + ldev, TYPE_SCRATCHPAD, 0x400); +} + +static void scratchpad_reset (DeviceState *dev) +{ + ScratchPad *s = SCRATCHPAD(dev); + + s->reg = 0; +} + +static void scratchpad_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + LBusDeviceClass *ldc = LBUS_DEVICE_CLASS(klass); + + dc->realize = scratchpad_realize; + dc->reset = scratchpad_reset; +
Quoted 8 lines
Quoted 6 lines
+
ldc->config=
+ ENGINE_CONFIG_NEXT /* valid */+ | 0x00010000 /* slots */ + | 0x00001000 /* version */ + | ENGINE_CONFIG_TYPE_SCRATCHPAD /* type */ + | 0x00000007; /* crc */where is ->config used ?
Yes, Its not but I am thinking of keeping it as next step we may need it.
Thanks for the review.
~ Ninad
Quoted 67 lines
Quoted 66 lines
hw/fsi/engine-scratchpad.c new file +16
-0+} + +static const TypeInfo scratchpad_info = { + .name = TYPE_SCRATCHPAD, + .parent = TYPE_LBUS_DEVICE, + .instance_size = sizeof(ScratchPad), + .class_init = scratchpad_class_init, + .class_size = sizeof(LBusDeviceClass), +}; + +static void scratchpad_register_types (void ) +{ + type_register_static(&scratchpad_info); +} + +type_init (scratchpad_register_types);hw/fsi/meson.build +1
-0@@ -1 +1,2 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true:files('engine-scratchpad.c'))
include/hw/fsi/engine-scratchpad.h new file +25
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engne +*/ +#ifndef FSI_ENGINE_SCRATCHPAD_H +#define FSI_ENGINE_SCRATCHPAD_H + +#include "qemu/bitops.h" + +#include "hw/fsi/lbus.h" + +#define ENGINE_CONFIG_NEXT BE_BIT(0) +#define ENGINE_CONFIG_VPD BE_BIT(1) +#define ENGINE_CONFIG_SLOTS BE_GENMASK(8, 15) +#define ENGINE_CONFIG_VERSION BE_GENMASK(16, 19) +#define ENGINE_CONFIG_TYPE BE_GENMASK(20, 27) +#define ENGINE_CONFIG_TYPE_PEEK (0x02 << 4) +#define ENGINE_CONFIG_TYPE_FSI (0x03 << 4) +#define ENGINE_CONFIG_TYPE_SCRATCHPAD (0x06 << 4) +#define ENGINE_CONFIG_CRC BE_GENMASK(28, 31) + +#define TYPE_SCRATCHPAD "scratchpad" +#define SCRATCHPAD (obj) OBJECT_CHECK(ScratchPad, (obj),
TYPE_SCRATCHPAD)include/hw/fsi/engine-scratchpad.h new file +8
-0+ +typedef struct ScratchPad { + LBusDevice parent; + + uint32_t reg; +}ScratchPad ; + +#endif /* FSI_ENGINE_SCRATCHPAD_H */
Re: [PATCH v4 02/10] hw/fsi: Introduce IBM's scratchpad
In reply to Cédric Le GoaterHello Cedric,
Quoted 11 lines · Cédric Le Goater
Quoted 7 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The LBUS device is embeded inside the scratchpad. The scratchpad provides a non-functional registers. There is a 1-1 relation between scratchpad and LBUS devices. Each LBUS device has 1K memory mapped in the LBUS.
The commit log is a bit confusing.
I have improved it in my next patch. Please check and let me know.
Thanks for the review.
~Ninad
Quoted 189 lines
C.
Quoted 184 lines
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
---
hw/fsi/Kconfig | 4 ++ hw/fsi/engine-scratchpad.c | 100 +++++++++++++++++++++++++++++ hw/fsi/meson.build | 1 +include/hw/fsi/engine-scratchpad.h| 33 ++++++++++4 files changed, 138 insertions(+)create mode 100644
hw/fsi/engine-scratchpad.ccreate mode 100644include/hw/fsi/engine-scratchpad.hhw/fsi/Kconfig +4
-0@@ -1,2 +1,6 @@ +config SCRATCHPAD + bool + select LBUS +config LBUS
boolhw/fsi/engine-scratchpad.c new file +15
-0@@ -0,0 +1,100 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engine +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/engine-scratchpad.h" + +static uint64_t scratchpad_read(void *opaque, hwaddr addr, unsignedsize)
hw/fsi/engine-scratchpad.c new file +9
-0+{ + ScratchPad *s = SCRATCHPAD(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: read @0x%" HWADDR_PRIx " size=%d\n", + __func__, addr, size); + + if (addr) { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Out of bounds read: 0x%"HWADDR_PRIx" for%u\n",
+__func__, addr, size);
+ return 0;
+ }hw/fsi/engine-scratchpad.c new file +15
-0+ + return s->reg; +} + +static void scratchpad_write(void *opaque, hwaddr addr, uint64_t data, + unsigned size) +{ + ScratchPad *s = SCRATCHPAD(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: write @0x%" HWADDR_PRIx " size=%d " + "value=%"PRIx64"\n", __func__, addr, size, data); + + if (addr) { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Out of bounds write: 0x%"HWADDR_PRIx" for%u\n",
+__func__, addr, size);
+ return;
+ }hw/fsi/engine-scratchpad.c new file +55
-0+ + s->reg = data; +} + +static const struct MemoryRegionOps scratchpad_ops = { + .read = scratchpad_read, + .write = scratchpad_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void scratchpad_realize (DeviceState *dev,Error **errp) +{ + LBusDevice *ldev = LBUS_DEVICE(dev); + + memory_region_init_io(&ldev->iomem, OBJECT(ldev), &scratchpad_ops, + ldev, TYPE_SCRATCHPAD, 0x400); +} + +static void scratchpad_reset (DeviceState *dev) +{ + ScratchPad *s = SCRATCHPAD(dev); + + s->reg = 0; +} + +static void scratchpad_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + LBusDeviceClass *ldc = LBUS_DEVICE_CLASS(klass); + + dc->realize = scratchpad_realize; + dc->reset = scratchpad_reset; + + ldc->config = + ENGINE_CONFIG_NEXT /* valid */ + | 0x00010000 /* slots */ + | 0x00001000 /* version */ + | ENGINE_CONFIG_TYPE_SCRATCHPAD /* type */ + | 0x00000007; /* crc */ +} + +static const TypeInfo scratchpad_info = { + .name = TYPE_SCRATCHPAD, + .parent = TYPE_LBUS_DEVICE, + .instance_size = sizeof(ScratchPad), + .class_init = scratchpad_class_init, + .class_size = sizeof(LBusDeviceClass), +}; + +static void scratchpad_register_types (void ) +{ + type_register_static(&scratchpad_info); +} + +type_init (scratchpad_register_types);hw/fsi/meson.build +1
-0@@ -1 +1,2 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true:files('engine-scratchpad.c'))
include/hw/fsi/engine-scratchpad.h new file +25
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM scratchpad engne +*/ +#ifndef FSI_ENGINE_SCRATCHPAD_H +#define FSI_ENGINE_SCRATCHPAD_H + +#include "qemu/bitops.h" + +#include "hw/fsi/lbus.h" + +#define ENGINE_CONFIG_NEXT BE_BIT(0) +#define ENGINE_CONFIG_VPD BE_BIT(1) +#define ENGINE_CONFIG_SLOTS BE_GENMASK(8, 15) +#define ENGINE_CONFIG_VERSION BE_GENMASK(16, 19) +#define ENGINE_CONFIG_TYPE BE_GENMASK(20, 27) +#define ENGINE_CONFIG_TYPE_PEEK (0x02 << 4) +#define ENGINE_CONFIG_TYPE_FSI (0x03 << 4) +#define ENGINE_CONFIG_TYPE_SCRATCHPAD (0x06 << 4) +#define ENGINE_CONFIG_CRC BE_GENMASK(28, 31) + +#define TYPE_SCRATCHPAD "scratchpad" +#define SCRATCHPAD (obj) OBJECT_CHECK(ScratchPad, (obj),
TYPE_SCRATCHPAD)include/hw/fsi/engine-scratchpad.h new file +8
-0+ +typedef struct ScratchPad { + LBusDevice parent; + + uint32_t reg; +}ScratchPad ; + +#endif /* FSI_ENGINE_SCRATCHPAD_H */
Re: [PATCH v4 03/10] hw/fsi: Introduce IBM's cfam,fsi-slave
In reply to Cédric Le GoaterHello Cedric,
Thanks for the review.
Quoted 98 lines · Cédric Le Goater
Quoted 97 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on busses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated Joel's review comments.
v3:
- Incorporated Thomas Huth's review comments.
---
hw/fsi/Kconfig | 9 ++
hw/fsi/cfam.c | 238 +++++++++++++++++++++++++++++++++++++ hw/fsi/fsi-slave.c | 109 +++++++++++++++++ hw/fsi/meson.build | 2 +
hw/fsi/trace-events | 5 +
include/hw/fsi/cfam.h | 61 ++++++++++include/hw/fsi/fsi-slave.h| 29 +++++7 files changed, 453 insertions(+)create mode 100644
hw/fsi/cfam.c
create mode 100644hw/fsi/fsi-slave.c
create mode 100644 hw/fsi/trace-events
create mode 100644include/hw/fsi/cfam.h
create mode 100644include/hw/fsi/fsi-slave.hhw/fsi/Kconfig +9
-0@@ -1,3 +1,12 @@ +config CFAM + bool + select FSI + select SCRATCHPAD + select LBUS + +config FSI + bool +config SCRATCHPAD
bool
select LBUShw/fsi/cfam.c new file +28
-0@@ -0,0 +1,238 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Common FRU Access Macro +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" +#include "trace.h" + +#include "hw/fsi/bits.h" +#include "hw/fsi/cfam.h" +#include "hw/fsi/engine-scratchpad.h" + +#include "hw/qdev-properties.h" + +#define TO_REG (x) ((x) >> 2) + +#define CFAM_ENGINE_CONFIG TO_REG(0x04) + +#define CFAM_CONFIG_CHIP_ID TO_REG(0x00) +#define CFAM_CONFIG_CHIP_ID_P9 0xc0022d15 +#define CFAM_CONFIG_CHIP_ID_BREAK 0xc0de0000 + +static uint64_t cfam_config_read(void *opaque, hwaddr addr, unsignedsize)
hw/fsi/cfam.c new file +8
-0+{ + CFAMConfig *config; + CFAMState *cfam; + LBusNode *node; + int i; + + config = CFAM_CONFIG(opaque); + cfam = container_of(config, CFAMState, config);
Quoted 8 lines
hw/fsi/cfam.c line 41
Quoted 5 lines
hw/fsi/cfam.c new file +5
-0+ + trace_cfam_config_read(addr, size); + + assert(size == 4); + assert(!(addr & 3));These checks are useless if the MemoryRegionOps is defined accordingly.
Good suggestion. Updated MemoryRegionOps registration and removed these asserts.
Quoted 21 lines
Quoted 17 lines
+
+ switch (addr) {
+ case0x00:
+ returnCFAM_CONFIG_CHIP_ID_P9;
+ case0x04:
+ returnENGINE_CONFIG_NEXT+ | 0x00010000 /* slots */ + | 0x00001000 /* version */ + | ENGINE_CONFIG_TYPE_PEEK /* type */ + | 0x0000000c; /* crc */ + case 0x08: + return ENGINE_CONFIG_NEXT + | 0x00010000 /* slots */ + | 0x00005000 /* version */ + | ENGINE_CONFIG_TYPE_FSI /* type */ + | 0x0000000a; /* crc */Quoted 3 lines
+ break;
+ default:
+ /* FIXME: Improve this */
Quoted 1 line
This looks hacky. What is it suppose to do ?
Yes, This is kind of work in progress. Looks like it is expecting address 0xc onwards devices and if we find any device then it will return config data for that device otherwise its a bad things and sends a break to reset.
Quoted 16 lines
Quoted 16 lines
+ i =
0xc;
+QLIST_FOREACH(node, &cfam->lbus.devices, next){ + if (i == addr) {
+ return LBUS_DEVICE_GET_CLASS(node->ldev)->config; + }
+ i += size;
+ }hw/fsi/cfam.c new file +7
-0+ + if (i == addr) { + return 0; + } + + /* +* As per FSI specification, This is a magic value at
Quoted 8 lines
Quoted 6 lines
address 0 of
+ * given FSI port. This causes FSI master to send BREAK command for
+ * initialization and recovery.
+ */
+ return0xc0de0000;we could use a definition.
Fixed
Quoted 15 lines
hw/fsi/cfam.c line 90
Quoted 13 lines
+ }
hw/fsi/cfam.c new file +11
-0+} + +static void cfam_config_write (void *opaque,hwaddr addr,uint64_t data, + unsigned size) +{ + CFAMConfig *s = CFAM_CONFIG(opaque); + + trace_cfam_config_write(addr, size, data); + + assert(size == 4); + assert(!(addr & 3));These checks are useless if the MemoryRegionOps is defined accordingly.
Removed.
Quoted 28 lines
Quoted 28 lines
hw/fsi/cfam.c new file +27
-0+ + switch (TO_REG(addr)) { + case CFAM_CONFIG_CHIP_ID: + case CFAM_CONFIG_CHIP_ID + 4: + if (data == CFAM_CONFIG_CHIP_ID_BREAK) { + bus_cold_reset(qdev_get_parent_bus(DEVICE(s))); + } + break; + default: + qemu_log_mask(LOG_GUEST_ERROR, "%s: Not implemented: 0x%" + HWADDR_PRIx" for %u\n", + __func__, addr, size); + } +} + +static const struct MemoryRegionOps cfam_config_ops = { + .read = cfam_config_read, + .write = cfam_config_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void cfam_config_realize (DeviceState *dev,Error **errp) +{ + CFAMConfig *s = CFAM_CONFIG(dev); + + memory_region_init_io(&s->iomem, OBJECT(s), &cfam_config_ops, s, + TYPE_CFAM_CONFIG, 0x400);
Quoted 8 lines
hw/fsi/cfam.c line 123
Quoted 6 lines
hw/fsi/cfam.c new file +6
-0+} + +static void cfam_config_reset (DeviceState *dev) +{ + /* Config is read-only */ +}Simply remove.
Removed.
Quoted 47 lines
Quoted 47 lines
hw/fsi/cfam.c new file +25
-0+ +static void cfam_config_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + dc->bus_type = TYPE_LBUS; + dc->realize = cfam_config_realize; + dc->reset = cfam_config_reset; +} + +static const TypeInfo cfam_config_info = { + .name = TYPE_CFAM_CONFIG, + .parent = TYPE_DEVICE, + .instance_size = sizeof(CFAMConfig), + .class_init = cfam_config_class_init, +}; + +static uint64_t cfam_unimplemented_read (void *opaque,hwaddr addr, + unsigned size) +{ + trace_cfam_unimplemented_read(addr, size); + + return 0; +} + +static void cfam_unimplemented_write(void *opaque, hwaddr addr,
uint64_tdata,
+ unsigned size)hw/fsi/cfam.c new file +18
-0+{ + trace_cfam_unimplemented_write(addr, size, data); +} + +static const struct MemoryRegionOps cfam_unimplemented_ops = { + .read = cfam_unimplemented_read, + .write = cfam_unimplemented_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void cfam_realize (DeviceState *dev,Error **errp) +{ + CFAMState *cfam = CFAM(dev); + FSISlaveState *slave = FSI_SLAVE(dev); + Error *err = NULL; + + /* Each slave has a 2MiB address space */ + memory_region_init_io(&cfam->mr, OBJECT(cfam),
Quoted 8 lines
Quoted 6 lines
&cfam_unimplemented_ops,
+ cfam,TYPE_CFAM, 2 * 1024 * 1024); +address_space_init(&cfam->as, &cfam->mr, TYPE_CFAM); +
+ qbus_init(&cfam->lbus,sizeof(cfam->lbus),TYPE_LBUS, + DEVICE(cfam), NULL);shouldn't that be in the
cfam_initroutine ? not sure.
I think we need bus init here because we need to create scratchpad by default.
Quoted 11 lines
Quoted 10 lines
+
lbus_create_device(&cfam->lbus, TYPE_SCRATCHPAD, 0); +
+object_property_set_bool(OBJECT(&cfam->config), "realized", true, &err);> + if (err) {
+error_propagate(errp, err);
+ return;
+ }
+qdev_set_parent_bus(DEVICE(&cfam->config), BUS(&cfam->lbus), &error_abort);
Quoted 1 line
why isn't
cfam->configcreated withlbus_create_device()?
cfam owns the bus hence setting parent should be done in cfam.
Quoted 14 lines
Quoted 14 lines
+
object_property_set_bool(OBJECT(&cfam->lbus), "realized", true, &err); + if (err) {
+error_propagate(errp, err);
+ return;
+ }
+
+memory_region_add_subregion(&cfam->mr, 0, &cfam->config.iomem); + /*memory_region_add_subregion(&cfam->mr, 0x800, &cfam->lbus.peek.iomem); */
+memory_region_add_subregion(&cfam->mr, 0x800, &slave->iomem); +memory_region_add_subregion(&cfam->mr, 0xc00, &cfam->lbus.mr); +}
Quoted 8 lines
hw/fsi/cfam.c line 199
Quoted 6 lines
hw/fsi/cfam.c new file +6
-0+ +static void cfam_reset (DeviceState *dev) +{ + /* TODO: Figure out how inherited reset works */ + qemu_log_mask(LOG_UNIMP, "%s: Not implemented yet.\n", __func__); +}Simply remove for now.
Removed.
Quoted 83 lines
Quoted 83 lines
hw/fsi/cfam.c new file +6
-0+ +static void cfam_init (Object *o) +{ + CFAMState *s = CFAM(o); + + object_initialize_child(o, TYPE_CFAM_CONFIG, &s->config,
TYPE_CFAM_CONFIG);hw/fsi/cfam.c new file +33
-0+} + +static void cfam_finalize (Object *o) +{ + CFAMState *s = CFAM(o); + + address_space_destroy(&s->as); +} + +static void cfam_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + dc->bus_type = TYPE_FSI_BUS; + dc->realize = cfam_realize; + dc->reset = cfam_reset; +} + +static const TypeInfo cfam_info = { + .name = TYPE_CFAM, + .parent = TYPE_FSI_SLAVE, + .instance_init = cfam_init, + .instance_finalize = cfam_finalize, + .instance_size = sizeof(CFAMState), + .class_init = cfam_class_init, +}; + +static void cfam_register_types (void ) +{ + type_register_static(&cfam_config_info); + type_register_static(&cfam_info); +} + +type_init (cfam_register_types);hw/fsi/fsi-slave.c new file +36
-0@@ -0,0 +1,109 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface slave +*/ + +#include "qemu/osdep.h" + +#include "qemu/bitops.h" +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/fsi-slave.h" + +#define TO_REG (x) ((x) >> 2) + +#define FSI_SMODE TO_REG(0x00) +#define FSI_SMODE_WSTART BE_BIT(0) +#define FSI_SMODE_AUX_EN BE_BIT(1) +#define FSI_SMODE_SLAVE_ID BE_GENMASK(6, 7) +#define FSI_SMODE_ECHO_DELAY BE_GENMASK(8, 11) +#define FSI_SMODE_SEND_DELAY BE_GENMASK(12, 15) +#define FSI_SMODE_LBUS_DIV BE_GENMASK(20, 23) +#define FSI_SMODE_BRIEF_LEFT BE_GENMASK(24, 27) +#define FSI_SMODE_BRIEF_RIGHT BE_GENMASK(28, 31) + +#define FSI_SDMA TO_REG(0x04) +#define FSI_SISC TO_REG(0x08) +#define FSI_SCISC TO_REG(0x08) +#define FSI_SISM TO_REG(0x0c) +#define FSI_SISS TO_REG(0x10) +#define FSI_SSISM TO_REG(0x10) +#define FSI_SCISM TO_REG(0x14) + +static uint64_t fsi_slave_read(void *opaque, hwaddr addr, unsigned
Quoted 8 lines
hw/fsi/fsi-slave.c line 41
Quoted 6 lines
size)
hw/fsi/fsi-slave.c new file +5
-0+{ + FSISlaveState *s = FSI_SLAVE(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: read @0x%" HWADDR_PRIx " size=%d\n", + __func__, addr, size);This is a trace event
Made it trace event.
Quoted 8 lines
Quoted 6 lines
+ if (addr + size >
sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds read: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);I don't think this check is necessary if the MMIO region is sized correctly.
I think it is nice to have because even if address is aligned we don't want it to be beyond limit.
Quoted 16 lines
Quoted 4 lines
+ return 0;
+ }hw/fsi/fsi-slave.c new file +1
-0+hw/fsi/fsi-slave.c line 59
Quoted 10 lines
hw/fsi/fsi-slave.c new file +10
-0+ return s->regs[TO_REG(addr)]; +} + +static void fsi_slave_write (void *opaque,hwaddr addr,uint64_t data, + unsigned size) +{ + FSISlaveState *s = FSI_SLAVE(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: write @0x%" HWADDR_PRIx " size=%d " + "value=%"PRIx64"\n", __func__, addr, size, data);This is a trace event
Converted to trace event.
Quoted 24 lines
Quoted 24 lines
+ if (addr + size >
sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds write: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return;
+ }hw/fsi/fsi-slave.c new file +16
-0+ + s->regs[TO_REG(addr)] = data; +} + +static const struct MemoryRegionOps fsi_slave_ops = { + .read = fsi_slave_read, + .write = fsi_slave_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void fsi_slave_init (Object *o) +{ + FSISlaveState *s = FSI_SLAVE(o); + + memory_region_init_io(&s->iomem, OBJECT(s), &fsi_slave_ops, + s, TYPE_FSI_SLAVE, 0x400);
Quoted 8 lines
hw/fsi/fsi-slave.c line 88
Quoted 6 lines
hw/fsi/fsi-slave.c new file +6
-0+} + +static void fsi_slave_reset (DeviceState *dev) +{ + /* FIXME */ +}Simply remove the reset for now.
Removed.
~Ninad
Quoted 148 lines
Quoted 147 lines
hw/fsi/fsi-slave.c new file +21
-0+ +static void fsi_slave_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + dc->reset = fsi_slave_reset; +} + +static const TypeInfo fsi_slave_info = { + .name = TYPE_FSI_SLAVE, + .parent = TYPE_DEVICE, + .instance_init = fsi_slave_init, + .instance_size = sizeof(FSISlaveState), + .class_init = fsi_slave_class_init, +}; + +static void fsi_slave_register_types (void ) +{ + type_register_static(&fsi_slave_info); +} + +type_init (fsi_slave_register_types);hw/fsi/meson.build +2
-0@@ -1,2 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c'))hw/fsi/trace-events new file +2
-0@@ -0,0 +1,5 @@ +cfam_config_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d" +cfam_config_write(uint64_t addr, uint32_t size, uint64_t data)"@0x%" PRIx64 " size=%d value=0x%"PRIx64
hw/fsi/trace-events new file +2
-0+ +cfam_unimplemented_read(uint64_t addr, uint32_t size) "@0x%" PRIx64" size=%d"
+cfam_unimplemented_write(uint64_t addr,uint32_tsize,uint64_tdata) "@0x%" PRIx64 " size=%d value=0x%"PRIx64include/hw/fsi/cfam.h new file +61
-0@@ -0,0 +1,61 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Common FRU Access Macro +*/ +#ifndef FSI_CFAM_H +#define FSI_CFAM_H + +#include "exec/memory.h" + +#include "hw/fsi/fsi-slave.h" +#include "hw/fsi/lbus.h" + +#define TYPE_FSI_BUS "fsi.bus" + +#define TYPE_CFAM "cfam" +#define CFAM (obj) OBJECT_CHECK(CFAMState, (obj), TYPE_CFAM) + +#define CFAM_NR_REGS ((0x2e0 >> 2) + 1) + +#define TYPE_CFAM_CONFIG "cfam.config" +#define CFAM_CONFIG (obj) \ + OBJECT_CHECK(CFAMConfig, (obj), TYPE_CFAM_CONFIG) +/* P9-ism */ +#define CFAM_CONFIG_NR_REGS 0x28 + +typedef struct CFAMState CFAMState ; + +/* TODO: Generalise this accommodate different CFAM configurations */ +typedef struct CFAMConfig { + DeviceState parent; + + MemoryRegion iomem; +}CFAMConfig ; + +#define TYPE_CFAM_PEEK "cfam.peek" +#define CFAM_PEEK (obj) \ + OBJECT_CHECK(CFAMPeek, (obj), TYPE_CFAM_PEEK) +#define CFAM_PEEK_NR_REGS ((0x130 >> 2) + 1) + +typedef struct CFAMPeek { + DeviceState parent; + + MemoryRegion iomem; +}CFAMPeek ; + +struct CFAMState { + /* < private > */ + FSISlaveState parent; + + MemoryRegion mr; + AddressSpace as; + + CFAMConfig config; + CFAMPeek peek; + + LBus lbus; +}; + +#endif /* FSI_CFAM_H */ include/hw/fsi/fsi-slave.h new file +29
-0@@ -0,0 +1,29 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface slave +*/ +#ifndef FSI_FSI_SLAVE_H +#define FSI_FSI_SLAVE_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" + +#include "hw/fsi/lbus.h" + +#include <stdint.h> + +#define TYPE_FSI_SLAVE "fsi.slave" +#define FSI_SLAVE (obj) \ + OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +#define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1) + +typedef struct FSISlaveState { + DeviceState parent; + + MemoryRegion iomem; + uint32_t regs[FSI_SLAVE_CONTROL_NR_REGS]; +}FSISlaveState ; + +#endif /* FSI_FSI_H */
Re: [PATCH v4 04/10] hw/fsi: Introduce IBM's FSI
In reply to Cédric Le GoaterHello Cedirc,
Thanks for the review.
Quoted 44 lines · Cédric Le Goater
Quoted 43 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
This commit models the FSI bus. CFAM is hanging out of FSI bus. The bus is model such a way that it is embeded inside the FSI master which is a bus controller.
The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>Reviewed-by Joel Stanley <[email protected]>---
v2:
- Incorporated review comments by Joel
---
hw/fsi/cfam.c | 3 +-
hw/fsi/fsi-master.c | 203 ++++++++++++++++++++++++++++++++++++ hw/fsi/fsi.c | 54 ++++++++++ hw/fsi/meson.build | 2 +-
include/hw/fsi/cfam.h | 8 +-include/hw/fsi/fsi-master.h| 30 ++++++ include/hw/fsi/fsi-slave.h | 4 +-
include/hw/fsi/fsi.h | 31 ++++++8 files changed, 327 insertions(+), 8 deletions(-)create mode 100644
hw/fsi/fsi-master.c
create mode 100644hw/fsi/fsi.c
create mode 100644include/hw/fsi/fsi-master.h
create mode 100644include/hw/fsi/fsi.hhw/fsi/cfam.c +0
-0@@ -7,12 +7,13 @@ #include "qemu/osdep.h"+#include "
qemu/bitops.h"
#include "qapi/error.h"
#include "qemu/log.h"
Quoted 8 lines
Quoted 6 lines
#include "
trace.h"
-#include "hw/fsi/bits.h"
#include "hw/fsi/cfam.h"
+#include "hw/fsi/fsi.h"
#include "hw/fsi/engine-scratchpad.h"
#include "hw/qdev-properties.h"These change do not belong to this patch.
Fixed it but keeping include of fsi.h and removal of bitops.h as this is where we are defining the bits.
Quoted 87 lines
Quoted 87 lines
hw/fsi/fsi-master.c new file +79
-0@@ -0,0 +1,203 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface master +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" + +#include "qemu/log.h" + +#include "hw/fsi/bits.h" +#include "hw/fsi/fsi-master.h" + +#define TYPE_OP_BUS "opb" + +#define TO_REG (x) ((x) >> 2) + +#define FSI_MMODE TO_REG(0x000) +#define FSI_MMODE_IPOLL_DMA_EN BE_BIT(0) +#define FSI_MMODE_HW_ERROR_RECOVERY_EN BE_BIT(1) +#define FSI_MMODE_RELATIVE_ADDRESS_EN BE_BIT(2) +#define FSI_MMODE_PARITY_CHECK_EN BE_BIT(3) +#define FSI_MMODE_CLOCK_DIVIDER_0 BE_GENMASK(4, 13) +#define FSI_MMODE_CLOCK_DIVIDER_1 BE_GENMASK(14, 23) +#define FSI_MMODE_DEBUG_EN BE_BIT(24) + +#define FSI_MDELAY TO_REG(0x004) +#define FSI_MDELAY_ECHO_0 BE_GENMASK(0, 3) +#define FSI_MDELAY_SEND_0 BE_GENMASK(4, 7) +#define FSI_MDELAY_ECHO_1 BE_GENMASK(8, 11) +#define FSI_MDELAY_SEND_1 BE_GENMASK(12, 15) + +#define FSI_MENP0 TO_REG(0x010) +#define FSI_MENP32 TO_REG(0x014) +#define FSI_MSENP0 TO_REG(0x018) +#define FSI_MLEVP0 TO_REG(0x018) +#define FSI_MSENP32 TO_REG(0x01c) +#define FSI_MLEVP32 TO_REG(0x01c) +#define FSI_MCENP0 TO_REG(0x020) +#define FSI_MREFP0 TO_REG(0x020) +#define FSI_MCENP32 TO_REG(0x024) +#define FSI_MREFP32 TO_REG(0x024) + +#define FSI_MAEB TO_REG(0x070) +#define FSI_MAEB_ANY_CPU_ERROR BE_BIT(0) +#define FSI_MAEB_ANY_DMA_ERROR BE_GENMASK(1, 16) +#define FSI_MAEB_ANY_PARITY_ERROR BE_BIT(17) + +#define FSI_MVER TO_REG(0x074) +#define FSI_MVER_VERSION BE_GENMASK(0, 7) +#define FSI_MVER_BRIDGES BE_GENMASK(8, 15) +#define FSI_MVER_PORTS BE_GENMASK(16, 23) + +#define FSI_MRESP0 TO_REG(0x0d0) +#define FSI_MRESP0_RESET_PORT_GENERAL BE_BIT(0) +#define FSI_MRESP0_RESET_PORT_ERROR BE_BIT(1) +#define FSI_MRESP0_RESET_ALL_BRIDGES_GENERAL BE_BIT(2) +#define FSI_MRESP0_RESET_ALL_PORTS_GENERAL BE_BIT(3) +#define FSI_MRESP0_RESET_MASTER BE_BIT(4) +#define FSI_MRESP0_RESET_PARITY_ERROR_LATCH BE_BIT(5) + +#define FSI_MRESB0 TO_REG(0x1d0) +#define FSI_MRESB0_RESET_GENERAL BE_BIT(0) +#define FSI_MRESB0_RESET_ERROR BE_BIT(1) +#define FSI_MRESB0_SET_DMA_SUSPEND BE_BIT(5) +#define FSI_MRESB0_CLEAR_DMA_SUSPEND BE_BIT(6) +#define FSI_MRESB0_SET_DELAY_MEASURE BE_BIT(7) + +#define FSI_MECTRL TO_REG(0x2e0) +#define FSI_MECTRL_TEST_PULSE BE_GENMASK(0, 7) +#define FSI_MECTRL_INHIBIT_PARITY_ERROR BE_GENMASK(8, 15) +#define FSI_MECTRL_ENABLE_OPB_ERR_ACK BE_BIT(16) +#define FSI_MECTRL_AUTO_TERMINATE BE_BIT(17) +#define FSI_MECTRL_PORT_ERROR_FREEZE BE_BIT(18) + +static uint64_t fsi_master_read(void *opaque, hwaddr addr, unsignedsize)
Quoted 8 lines
hw/fsi/fsi-master.c line 84
Quoted 5 lines
hw/fsi/fsi-master.c new file +5
-0+{ + FSIMasterState *s = FSI_MASTER(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: read @0x%" HWADDR_PRIx " size=%d\n", + __func__, addr, size);This should be a trace event.
Fixed it.
Quoted 15 lines
Quoted 15 lines
+
+ if (addr + size >sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds read: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return 0;
+ }hw/fsi/fsi-master.c new file +6
-0+ + return s->regs[TO_REG(addr)]; +} + +static void fsi_master_write (void *opaque,hwaddr addr,uint64_t data, + unsigned size)
Quoted 8 lines
hw/fsi/fsi-master.c line 102
Quoted 5 lines
hw/fsi/fsi-master.c new file +5
-0+{ + FSIMasterState *s = FSI_MASTER(opaque); + + qemu_log_mask(LOG_UNIMP, "%s: write @0x%" HWADDR_PRIx " size=%d " + "value=%"PRIx64"\n", __func__, addr, size, data);This should be a trace event.
Fixed it.
Quoted 124 lines
Quoted 124 lines
+ if (addr + size >
sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds write: %"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return;
+ }
+
+ switch (TO_REG(addr)) {
+ caseFSI_MENP0:
+ s->regs[FSI_MENP0] = data;
+ break;
+ caseFSI_MENP32:
+ s->regs[FSI_MENP32] = data;
+ break;
+ caseFSI_MSENP0:
+ s->regs[FSI_MENP0] |= data;
+ break;
+ caseFSI_MSENP32:
+ s->regs[FSI_MENP32] |= data;
+ break;
+ caseFSI_MCENP0:
+ s->regs[FSI_MENP0] &= ~data;
+ break;
+ caseFSI_MCENP32:
+ s->regs[FSI_MENP32] &= ~data;
+ break;
+ caseFSI_MRESP0:
+ /* Perform necessary resets leave register 0 to indicate no errors */
+ break;
+ caseFSI_MRESB0:
+ if (data &FSI_MRESB0_RESET_GENERAL) {
+ device_cold_reset(DEVICE(opaque));
+ }
+ if (data &FSI_MRESB0_RESET_ERROR) {
+ /* FIXME: this seems dubious */
+ device_cold_reset(DEVICE(opaque));
+ }
+ break;
+ default:
+ s->regs[TO_REG(addr)] = data;
+ }hw/fsi/fsi-master.c new file +18
-0+} + +static const struct MemoryRegionOps fsi_master_ops = { + .read = fsi_master_read, + .write = fsi_master_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void fsi_master_realize (DeviceState *dev,Error **errp) +{ + FSIMasterState *s = FSI_MASTER(dev); + Error *err = NULL; + + qbus_init(&s->bus, sizeof(s->bus), TYPE_FSI_BUS, DEVICE(s), NULL); + + memory_region_init_io(&s->iomem, OBJECT(s), &fsi_master_ops, s, + TYPE_FSI_MASTER, 0x10000000); + memory_region_init(&s->opb2fsi, OBJECT(s), "fsi.opb2fsi",
0x10000000);hw/fsi/fsi-master.c new file +41
-0+ + object_property_set_bool(OBJECT(&s->bus), "realized", true, &err); + if (err) { + error_propagate(errp, err); + return; + } + + memory_region_add_subregion(&s->opb2fsi, 0, &s->bus.slave.mr); +} + +static void fsi_master_reset (DeviceState *dev) +{ + FSIMasterState *s = FSI_MASTER(dev); + + /* ASPEED default */ + s->regs[FSI_MVER] = 0xe0050101; +} + +static void fsi_master_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->bus_type = TYPE_OP_BUS; + dc->desc = "FSI Master"; + dc->realize = fsi_master_realize; + dc->reset = fsi_master_reset; +} + +static const TypeInfo fsi_master_info = { + .name = TYPE_FSI_MASTER, + .parent = TYPE_DEVICE, + .instance_size = sizeof(FSIMasterState), + .class_init = fsi_master_class_init, +}; + +static void fsi_register_types (void ) +{ + type_register_static(&fsi_master_info); +} + +type_init (fsi_register_types);hw/fsi/fsi.c new file +13
-0@@ -0,0 +1,54 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface +*/ +#include "qemu/osdep.h" + +#include "qapi/error.h" + +#include "hw/fsi/fsi.h" +#include "hw/fsi/cfam.h" +
Quoted 8 lines
hw/fsi/fsi.c line 19
Quoted 6 lines
hw/fsi/fsi.c new file +6
-0+static void fsi_bus_realize (BusState *bus,Error **errp) +{ + FSIBus *s = FSI_BUS(bus); + Error *err = NULL; + + /* FIXME: Should be realised elsewhere and added to the bus */indeed.
Currently we have a single CFAM and it is defined as child of FSIBus hence we are realizing it here. I think when we move to multiple CFAMs at that time we can decide to move it somewhere. For now I will remove the FIXME comment. Please let me know.
Quoted 14 lines
hw/fsi/fsi.c line 30
Quoted 12 lines
hw/fsi/fsi.c new file +11
-0+object_property_set_bool (OBJECT (&s->slave),"realized" , true, &err); + if (err) { + error_propagate(errp, err); + } +} + +static void fsi_bus_init (Object *o) +{ + FSIBus *s = FSI_BUS(o); + + /* FIXME: Move this elsewhere */at the board level may be ?
Same as above.
Quoted 39 lines
Quoted 39 lines
hw/fsi/fsi.c new file +24
-0+ object_initialize_child(o, TYPE_CFAM, &s->slave, TYPE_CFAM); + qdev_set_parent_bus(DEVICE(&s->slave), BUS(o), &error_abort); +} + +static void fsi_bus_class_init (ObjectClass *klass,void *data) +{ + BusClass *bc = BUS_CLASS(klass); + bc->realize = fsi_bus_realize; +} + +static const TypeInfo fsi_bus_info = { + .name = TYPE_FSI_BUS, + .parent = TYPE_BUS, + .instance_init = fsi_bus_init, + .instance_size = sizeof(FSIBus), + .class_init = fsi_bus_class_init, +}; + +static void fsi_bus_register_types (void ) +{ + type_register_static(&fsi_bus_info); +} + +type_init (fsi_bus_register_types);hw/fsi/meson.build +1
-1@@ -1,4 +1,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) -system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi-slave.c')) +system_ss.add(when: 'CONFIG_FSI', if_true:
files('fsi.c','fsi-master.c','fsi-slave.c'))include/hw/fsi/cfam.h +0
-1--- a/include/hw/fsi/cfam.h
Quoted 8 lines
Quoted 6 lines
+++
b/include/hw/fsi/cfam.hinclude/hw/fsi/cfam.h +0
-0@@ -12,14 +12,14 @@ #include "hw/fsi/fsi-slave.h" #include "hw/fsi/lbus.h"-#define
TYPE_FSI_BUS"fsi.bus"
-unwanted change I guess ?
Fixed.
Quoted 9 lines
include/hw/fsi/cfam.h line 22
Quoted 7 lines
#define
TYPE_CFAM"cfam"
#define CFAM(obj)OBJECT_CHECK(CFAMState, (obj), TYPE_CFAM)#defineCFAM_NR_REGS((0x2e0>> 2) + 1)
#defineTYPE_CFAM_CONFIG"cfam.config"include/hw/fsi/cfam.h +2
-0+OBJECT_DECLARE_SIMPLE_TYPE (CFAMConfig,CFAM_CONFIG ) +same.
Fixed.
Quoted 56 lines
Quoted 56 lines
#define
CFAM_CONFIG(obj)\
OBJECT_CHECK(CFAMConfig, (obj), TYPE_CFAM_CONFIG)/* P9-ism */include/hw/fsi/cfam.h +2
-2@@ -35,8 +35,8 @@ typedef struct CFAMConfig { } CFAMConfig; #define TYPE_CFAM_PEEK "cfam.peek" -#define CFAM_PEEK (obj) \ - OBJECT_CHECK(CFAMPeek, (obj), TYPE_CFAM_PEEK) +OBJECT_DECLARE_SIMPLE_TYPE(CFAMPeek, CFAM_PEEK) + #define CFAM_PEEK_NR_REGS ((0x130 >> 2) + 1) typedef struct CFAMPeek {include/hw/fsi/fsi-master.h new file +30
-0@@ -0,0 +1,30 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2019 IBM Corp. +* +* IBM Flexible Service Interface Master +*/ +#ifndef FSI_FSI_MASTER_H +#define FSI_FSI_MASTER_H + +#include "exec/memory.h" +#include "hw/qdev-core.h" +#include "hw/fsi/fsi.h" + +#define TYPE_FSI_MASTER "fsi.master" +OBJECT_DECLARE_SIMPLE_TYPE(FSIMasterState, FSI_MASTER) + +#define FSI_MASTER_NR_REGS ((0x2e0 >> 2) + 1) + +typedef struct FSIMasterState { + DeviceState parent; + MemoryRegion iomem; + MemoryRegion opb2fsi; + + FSIBus bus; + + uint32_t regs[FSI_MASTER_NR_REGS]; +}FSIMasterState ; + + +#endif /* FSI_FSI_H */ include/hw/fsi/fsi-slave.h +0
-0@@ -15,8 +15,8 @@ #include <stdint.h> #define TYPE_FSI_SLAVE "fsi.slave"
Quoted 8 lines
include/hw/fsi/fsi-slave.h line 20
Quoted 5 lines
include/hw/fsi/fsi-slave.h +2
-2-#define FSI_SLAVE (obj) \ - OBJECT_CHECK(FSISlaveState, (obj), TYPE_FSI_SLAVE) +OBJECT_DECLARE_SIMPLE_TYPE(FSISlaveState, FSI_SLAVE) + #define FSI_SLAVE_CONTROL_NR_REGS ((0x40 >> 2) + 1)These change do not belong to this patch.
Fixed.
Thanks.
~Ninad
Quoted 42 lines
Quoted 41 lines
include/hw/fsi/fsi-slave.h +0
-0typedef struct FSISlaveState {include/hw/fsi/fsi.h new file +27
-0@@ -0,0 +1,31 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM Flexible Service Interface +*/ +#ifndef FSI_FSI_H +#define FSI_FSI_H + +#include "hw/qdev-core.h" + +/* + * TODO: Maybe unwind this dependency with const links? Store a + * pointer in FSIBus? + */ +#include "hw/fsi/cfam.h" + +#define TYPE_FSI_BUS "fsi.bus" +OBJECT_DECLARE_SIMPLE_TYPE(FSIBus, FSI_BUS) + +/* TODO: Figure out what's best with a point-to-point bus */ +typedef struct FSISlaveState FSISlaveState; + +typedef struct FSIBus { + BusState bus; + + /* XXX: It's point-to-point, just instantiate the slave directlyfor now */
+ CFAMState slave;include/hw/fsi/fsi.h new file +3
-0+} FSIBus; + +#endif
Re: [PATCH v4 05/10] hw/fsi: IBM's On-chip Peripheral Bus
In reply to Cédric Le GoaterHello Cedric,
Thanks for the review.
Quoted 50 lines · Cédric Le Goater
Quoted 49 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>Reviewed-by Joel Stanley <[email protected]>---
v2:
- Incorporated review comment by Joel.
---
hw/fsi/Kconfig | 4 +
hw/fsi/fsi-master.c | 6 +-
hw/fsi/meson.build | 1 +
hw/fsi/opb.c | 194 +++++++++++++++++++++++++++++++++++++++++++include/hw/fsi/opb.h| 43 ++++++++++5 files changed, 244 insertions(+), 4 deletions(-)create mode 100644
hw/fsi/opb.c
create mode 100644include/hw/fsi/opb.hhw/fsi/Kconfig +4
-0@@ -1,3 +1,7 @@ +config OPB + bool + select CFAM +config CFAM
bool
select FSIhw/fsi/fsi-master.c +0
-0@@ -7,14 +7,12 @@ #include "qemu/osdep.h"+#include "
qemu/bitops.h"
#include "qapi/error.h"
-
#include "qemu/log.h"
-#include "hw/fsi/bits.h"
Quoted 8 lines
Quoted 5 lines
#include "
hw/fsi/fsi-master.h"hw/fsi/fsi-master.c +1
-2- -#define TYPE_OP_BUS "opb" +#include "hw/fsi/opb.h" #define TO_REG(x) ((x) >> 2)
These change do not belong to this patch.
I fixed some of them but in this patch TYPE_OP_BUS is replaced by correct header file.
Quoted 32 lines
Quoted 32 lines
hw/fsi/meson.build +0
-0@@ -2,3 +2,4 @@ system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c'))
system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c'))hw/fsi/meson.build +1
-0+system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c'))hw/fsi/opb.c new file +15
-0@@ -0,0 +1,194 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM On-chip Peripheral Bus +*/ + +#include "qemu/osdep.h" + +#include "qapi/error.h" +#include "qemu/log.h" + +#include "hw/fsi/opb.h" + +static MemTxResult opb_read(OPBus *opb, hwaddr addr, void *data,
Quoted 8 lines
Quoted 6 lines
size_tlen)
+{
+ return address_space_read(&opb->as, addr,MEMTXATTRS_UNSPECIFIED, data,
+ len);
+}This routine doesn't look very useful. Same for the write.
Now I made them to qemu_log the error.
Quoted 13 lines
hw/fsi/opb.c line 28
Quoted 10 lines
hw/fsi/opb.c new file +9
-0+ +uint8_t opb_read8 (OPBus *opb,hwaddr addr) +{ + MemTxResult tx; + uint8_t data; + + tx = opb_read(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx);should output a
qemu_log_mask(LOG_GUEST_ERROR)may be ? But I don't think we should assert.
I removed tx check from all other functions.
Quoted 15 lines
hw/fsi/opb.c line 40
Quoted 13 lines
hw/fsi/opb.c new file +12
-0+ + return data; +} + +uint16_t opb_read16 (OPBus *opb,hwaddr addr) +{ + MemTxResult tx; + uint16_t data; + + tx = opb_read(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx);same
Same as above.
Quoted 218 lines
Quoted 217 lines
hw/fsi/opb.c new file +17
-0+ + return data; +} + +uint32_t opb_read32 (OPBus *opb,hwaddr addr) +{ + MemTxResult tx; + uint32_t data; + + tx = opb_read(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx); + + return data; +} + +static MemTxResult opb_write(OPBus *opb, hwaddr addr, void *data,
size_tlen)
+{
+ return address_space_write(&opb->as, addr,MEMTXATTRS_UNSPECIFIED, data,
+ len);hw/fsi/opb.c new file +44
-0+} + +void opb_write8 (OPBus *opb,hwaddr addr,uint8_t data) +{ + MemTxResult tx; + + tx = opb_write(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx); +} + +void opb_write16 (OPBus *opb,hwaddr addr,uint16_t data) +{ + MemTxResult tx; + + tx = opb_write(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx); +} + +void opb_write32 (OPBus *opb,hwaddr addr,uint32_t data) +{ + MemTxResult tx; + + tx = opb_write(opb, addr, &data, sizeof(data)); + /* FIXME: improve error handling */ + assert(!tx); +} + +void opb_fsi_master_address (OPBus *opb,hwaddr addr) +{ + memory_region_transaction_begin(); + memory_region_set_address(&opb->fsi.iomem, addr); + memory_region_transaction_commit(); +} + +void opb_opb2fsi_address (OPBus *opb,hwaddr addr) +{ + memory_region_transaction_begin(); + memory_region_set_address(&opb->fsi.opb2fsi, addr); + memory_region_transaction_commit(); +} + +static uint64_t opb_unimplemented_read(void *opaque, hwaddr addr,unsigned size)
hw/fsi/opb.c new file +8
-0+{ + qemu_log_mask(LOG_UNIMP, "%s: read @0x%" HWADDR_PRIx " size=%d\n", + __func__, addr, size); + + return 0; +} + +static void opb_unimplemented_write(void *opaque, hwaddr addr,
uint64_tdata,
+ unsigned size)hw/fsi/opb.c new file +17
-0+{ + qemu_log_mask(LOG_UNIMP, "%s: write @0x%" HWADDR_PRIx " size=%d " + "value=%"PRIx64"\n", __func__, addr, size, data); +} + +static const struct MemoryRegionOps opb_unimplemented_ops = { + .read = opb_unimplemented_read, + .write = opb_unimplemented_write, + .endianness = DEVICE_BIG_ENDIAN, +}; + +static void opb_realize (BusState *bus,Error **errp) +{ + OPBus *opb = OP_BUS(bus); + Error *err = NULL; + + memory_region_init_io(&opb->mr, OBJECT(opb),
&opb_unimplemented_ops, opb,
+ NULL,UINT32_MAX);
+address_space_init(&opb->as, &opb->mr, "opb");
+
+object_property_set_bool(OBJECT(&opb->fsi), "realized", true, &err);
+ if (err) {
+error_propagate(errp, err);
+ return;
+ }
+memory_region_add_subregion(&opb->mr, 0x80000000, &opb->fsi.iomem); +
+ /* OPB2FSI region */
+ /*
+ * Avoid endianness issues by mapping each slave's memory region directly.
+ * Manually bridging multiple address-spaces causes endian swapping + * headaches asmemory_region_dispatch_read()and
+ *memory_region_dispatch_write()correct the endianness based on the
+ * target machine endianness and not relative to the device endianness on
+ * either side of the bridge.
+ */
+ /*
+ * XXX: This is a bit hairy and will need to be fixed when I sort out the
+ * bus/slave relationship and any changes to the CFAM modelling (multiple
+ * slaves, LBUS)
+ */
+memory_region_add_subregion(&opb->mr, 0xa0000000, &opb->fsi.opb2fsi);hw/fsi/opb.c new file +7
-0+} + +static void opb_init (Object *o) +{ + OPBus *opb = OP_BUS(o); + + object_initialize_child(o, "fsi-master", &opb->fsi,
TYPE_FSI_MASTER);
+qdev_set_parent_bus(DEVICE(&opb->fsi), BUS(o), &error_abort);hw/fsi/opb.c new file +31
-0+} + +static void opb_finalize (Object *o) +{ + OPBus *opb = OP_BUS(o); + + address_space_destroy(&opb->as); +} + +static void opb_class_init (ObjectClass *klass,void *data) +{ + BusClass *bc = BUS_CLASS(klass); + bc->realize = opb_realize; +} + +static const TypeInfo opb_info = { + .name = TYPE_OP_BUS, + .parent = TYPE_BUS, + .instance_init = opb_init, + .instance_finalize = opb_finalize, + .instance_size = sizeof(OPBus), + .class_init = opb_class_init, + .class_size = sizeof(OPBusClass), +}; + +static void opb_register_types (void ) +{ + type_register_static(&opb_info); +} + +type_init (opb_register_types);include/hw/fsi/opb.h new file +43
-0@@ -0,0 +1,43 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* IBM On-Chip Peripheral Bus +*/ +#ifndef FSI_OPB_H +#define FSI_OPB_H + +#include "exec/memory.h" +#include "hw/fsi/fsi-master.h" + +#define TYPE_OP_BUS "opb" +OBJECT_DECLARE_SIMPLE_TYPE(OPBus, OP_BUS) + +typedef struct OPBus { + /*< private >*/ + BusState bus; + + /*< public >*/ + MemoryRegion mr; + AddressSpace as; + + /* Model OPB as dumb enough just to provide an address-space */ + /* TODO: Maybe don't store device state in the bus? */ + FSIMasterState fsi; +}OPBus ; + +typedef struct OPBusClass { + BusClass parent_class; +}OPBusClass ; + +uint8_t opb_read8 (OPBus *opb,hwaddr addr); +uint16_t opb_read16 (OPBus *opb,hwaddr addr); +uint32_t opb_read32 (OPBus *opb,hwaddr addr); +void opb_write8 (OPBus *opb,hwaddr addr,uint8_t data); +void opb_write16 (OPBus *opb,hwaddr addr,uint16_t data); +void opb_write32 (OPBus *opb,hwaddr addr,uint32_t data); + +void opb_fsi_master_address (OPBus *opb,hwaddr addr); +void opb_opb2fsi_address (OPBus *opb,hwaddr addr); + +#endif /* FSI_OPB_H */
Re: [PATCH v4 06/10] hw/fsi: Aspeed APB2OPB interface
In reply to Cédric Le GoaterHello Cedric,
Thanks for the review.
Quoted 70 lines · Cédric Le Goater
Quoted 69 lines · Ninad Palsule
This is a part of patchset where IBM's Flexible Service Interface is introduced.
An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>---
v2:
- Incorporated review comments by Joel
v3:
- Incorporated review comments by Thomas Huth
v4:
- Compile FSI withASPEED_SOConly.
---
hw/arm/Kconfig | 1 +
hw/fsi/Kconfig | 20 +- hw/fsi/aspeed-apb2opb.c | 352 ++++++++++++++++++++++++++++++++ hw/fsi/meson.build | 9 +- hw/fsi/trace-events | 3 +-
hw/fsi/trace.h | 1 +include/hw/fsi/aspeed-apb2opb.h| 33 +++
meson.build | 1 +8 files changed, 407 insertions(+), 13 deletions(-)create mode 100644
hw/fsi/aspeed-apb2opb.ccreate mode 100644hw/fsi/trace.h
create mode 100644include/hw/fsi/aspeed-apb2opb.hhw/arm/Kconfig +0
-0@@ -555,6 +555,7 @@ config ASPEED_SOCselect LED
select PMBUS
select MAX31785
+ selectFSI_APB2OPB_ASPEED
config MPS2
boolhw/fsi/Kconfig +1
-1@@ -1,19 +1,23 @@ -config OPB +config FSI_APB2OPB_ASPEEDbool
- select CFAM
+ selectFSI_OPB
-config CFAMhw/fsi/Kconfig +5
-0+config FSI_OPB + bool + select FSI_CFAM + +config FSI_CFAMbool
select FSI
- select SCRATCHPAD
- select LBUS
+ selectFSI_SCRATCHPAD
+ selectFSI_LBUS
config FSI
bool
-config SCRATCHPAD
+configFSI_SCRATCHPAD
bool
Quoted 8 lines
Quoted 5 lines
- select LBUS
+ selectFSI_LBUS
-config LBUS
+configFSI_LBUS
boolSome of these changes belong to another patch.
Fixed it.
Quoted 159 lines
Quoted 159 lines
hw/fsi/aspeed-apb2opb.c new file +18
-0@@ -0,0 +1,352 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* ASPEED APB-OPB FSI interface +*/ + +#include "qemu/osdep.h" +#include "qemu/log.h" +#include "qom/object.h" +#include "qapi/error.h" +#include "trace.h" + +#include "hw/fsi/aspeed-apb2opb.h" +#include "hw/qdev-core.h" + +#define TO_REG (x) (x >> 2) +#define GENMASK (t, b) (((1ULL << ((t) + 1)) - 1) & ~((1ULL << (b)) -1))
hw/fsi/aspeed-apb2opb.c new file +131
-0+ +#define APB2OPB_VERSION TO_REG(0x00) +#define APB2OPB_VERSION_VER GENMASK(7, 0) + +#define APB2OPB_TRIGGER TO_REG(0x04) +#define APB2OPB_TRIGGER_EN BIT(0) + +#define APB2OPB_CONTROL TO_REG(0x08) +#define APB2OPB_CONTROL_OFF GENMASK(31, 13) + +#define APB2OPB_OPB2FSI TO_REG(0x0c) +#define APB2OPB_OPB2FSI_OFF GENMASK(31, 22) + +#define APB2OPB_OPB0_SEL TO_REG(0x10) +#define APB2OPB_OPB1_SEL TO_REG(0x28) +#define APB2OPB_OPB_SEL_EN BIT(0) + +#define APB2OPB_OPB0_MODE TO_REG(0x14) +#define APB2OPB_OPB1_MODE TO_REG(0x2c) +#define APB2OPB_OPB_MODE_RD BIT(0) + +#define APB2OPB_OPB0_XFER TO_REG(0x18) +#define APB2OPB_OPB1_XFER TO_REG(0x30) +#define APB2OPB_OPB_XFER_FULL BIT(1) +#define APB2OPB_OPB_XFER_HALF BIT(0) + +#define APB2OPB_OPB0_ADDR TO_REG(0x1c) +#define APB2OPB_OPB0_WRITE_DATA TO_REG(0x20) + +#define APB2OPB_OPB1_DMA_EN TO_REG(0x24) +#define APB2OPB_OPB1_DMA_EN_3 BIT(3) +#define APB2OPB_OPB1_DMA_EN_2 BIT(2) +#define APB2OPB_OPB1_DMA_EN_1 BIT(1) +#define APB2OPB_OPB1_DMA_EN_0 BIT(0) + +#define APB2OPB_OPB1_ADDR TO_REG(0x34) +#define APB2OPB_OPB1_WRITE_DATA TO_REG(0x38) + +#define APB2OPB_OPB_CLK TO_REG(0x3c) +#define APB2OPB_OPB_CLK_SYNC BIT(0) + +#define APB2OPB_IRQ_CLEAR TO_REG(0x40) +#define APB2OPB_IRQ_CLEAR_EN BIT(0) + +#define APB2OPB_IRQ_MASK TO_REG(0x44) +#define APB2OPB_IRQ_MASK_OPB1_TX_ACK BIT(17) +#define APB2OPB_IRQ_MASK_OPB0_TX_ACK BIT(16) +#define APB2OPB_IRQ_MASK_CH3_TCONT BIT(15) +#define APB2OPB_IRQ_MASK_CH2_TCONT BIT(14) +#define APB2OPB_IRQ_MASK_CH1_TCONT BIT(13) +#define APB2OPB_IRQ_MASK_CH0_TCONT BIT(12) +#define APB2OPB_IRQ_MASK_CH3_FIFO_EMPTY BIT(11) +#define APB2OPB_IRQ_MASK_CH2_FIFO_EMPTY BIT(10) +#define APB2OPB_IRQ_MASK_CH1_FIFO_EMPTY BIT(9) +#define APB2OPB_IRQ_MASK_CH0_FIFO_EMPTY BIT(8) +#define APB2OPB_IRQ_MASK_CH3_FIFO_FULL BIT(7) +#define APB2OPB_IRQ_MASK_CH2_FIFO_FULL BIT(6) +#define APB2OPB_IRQ_MASK_CH1_FIFO_FULL BIT(5) +#define APB2OPB_IRQ_MASK_CH0_FIFO_FULL BIT(4) +#define APB2OPB_IRQ_MASK_CH3_DMA_EOT BIT(3) +#define APB2OPB_IRQ_MASK_CH2_DMA_EOT BIT(2) +#define APB2OPB_IRQ_MASK_CH1_DMA_EOT BIT(1) +#define APB2OPB_IRQ_MASK_CH0_DMA_EOT BIT(0) + +#define APB2OPB_IRQ_STS TO_REG(0x48) +#define APB2OPB_IRQ_STS_MASTER_ERROR BIT(28) +#define APB2OPB_IRQ_STS_PORT_ERROR BIT(27) +#define APB2OPB_IRQ_STS_HOTPLUG BIT(26) +#define APB2OPB_IRQ_STS_SLAVE_7 BIT(25) +#define APB2OPB_IRQ_STS_SLAVE_6 BIT(24) +#define APB2OPB_IRQ_STS_SLAVE_5 BIT(23) +#define APB2OPB_IRQ_STS_SLAVE_4 BIT(22) +#define APB2OPB_IRQ_STS_SLAVE_3 BIT(21) +#define APB2OPB_IRQ_STS_SLAVE_2 BIT(20) +#define APB2OPB_IRQ_STS_SLAVE_1 BIT(19) +#define APB2OPB_IRQ_STS_SLAVE_0 BIT(18) +#define APB2OPB_IRQ_STS_OPB1_TX_ACK BIT(17) +#define APB2OPB_IRQ_STS_OPB0_TX_ACK BIT(16) +#define APB2OPB_IRQ_STS_CH3_TCONT BIT(15) +#define APB2OPB_IRQ_STS_CH2_TCONT BIT(14) +#define APB2OPB_IRQ_STS_CH1_TCONT BIT(13) +#define APB2OPB_IRQ_STS_CH0_TCONT BIT(12) +#define APB2OPB_IRQ_STS_CH3_FIFO_EMPTY BIT(11) +#define APB2OPB_IRQ_STS_CH2_FIFO_EMPTY BIT(10) +#define APB2OPB_IRQ_STS_CH1_FIFO_EMPTY BIT(9) +#define APB2OPB_IRQ_STS_CH0_FIFO_EMPTY BIT(8) +#define APB2OPB_IRQ_STS_CH3_FIFO_FULL BIT(7) +#define APB2OPB_IRQ_STS_CH2_FIFO_FULL BIT(6) +#define APB2OPB_IRQ_STS_CH1_FIFO_FULL BIT(5) +#define APB2OPB_IRQ_STS_CH0_FIFO_FULL BIT(4) +#define APB2OPB_IRQ_STS_CH3_DMA_EOT BIT(3) +#define APB2OPB_IRQ_STS_CH2_DMA_EOT BIT(2) +#define APB2OPB_IRQ_STS_CH1_DMA_EOT BIT(1) +#define APB2OPB_IRQ_STS_CH0_DMA_EOT BIT(0) + +#define APB2OPB_OPB0_WRITE_WORD_ENDIAN TO_REG(0x4c) +#define APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE 0x0011101b +#define APB2OPB_OPB0_WRITE_BYTE_ENDIAN TO_REG(0x50) +#define APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE 0x0c330f3f +#define APB2OPB_OPB1_WRITE_WORD_ENDIAN TO_REG(0x54) +#define APB2OPB_OPB1_WRITE_BYTE_ENDIAN TO_REG(0x58) +#define APB2OPB_OPB0_READ_BYTE_ENDIAN TO_REG(0x5c) +#define APB2OPB_OPB0_READ_WORD_ENDIAN_BE 0x00030b1b +#define APB2OPB_OPB1_READ_BYTE_ENDIAN TO_REG(0x60) + +#define APB2OPB_RETRY TO_REG(0x64) +#define APB2OPB_RETRY_COUNTER GENMASK(15, 0) + +#define APB2OPB_OPB0_STATUS TO_REG(0x80) +#define APB2OPB_OPB1_STATUS TO_REG(0x8c) +#define APB2OPB_OPB_STATUS_TIMEOUT BIT(4) +#define APB2OPB_OPB_STATUS_RETRY BIT(3) +#define APB2OPB_OPB_STATUS_ERROR_ACK BIT(2) +#define APB2OPB_OPB_STATUS_FW_ACK BIT(1) +#define APB2OPB_OPB_STATUS_HW_ACK BIT(0) + +#define APB2OPB_OPB0_READ_DATA TO_REG(0x84) + +#define APB2OPB_OPB1_DMA_STATUS TO_REG(0x88) +#define APB2OPB_OPB1_DMA_STATUS_CH3_EOT BIT(7) +#define APB2OPB_OPB1_DMA_STATUS_CH2_EOT BIT(6) +#define APB2OPB_OPB1_DMA_STATUS_CH1_EOT BIT(5) +#define APB2OPB_OPB1_DMA_STATUS_CH0_EOT BIT(4) +#define APB2OPB_OPB1_DMA_STATUS_CH3_REQ BIT(3) +#define APB2OPB_OPB1_DMA_STATUS_CH2_REQ BIT(2) +#define APB2OPB_OPB1_DMA_STATUS_CH1_REQ BIT(1) +#define APB2OPB_OPB1_DMA_STATUS_CH0_REQ BIT(0) + +#define APB2OPB_OPB1_READ_DATA TO_REG(0x90) + +static uint64_t aspeed_apb2opb_read(void *opaque, hwaddr addr,unsigned size)
+{
Quoted 8 lines
hw/fsi/aspeed-apb2opb.c line 156
Quoted 6 lines
+ AspeedAPB2OPBState *s =
ASPEED_APB2OPB(opaque);hw/fsi/aspeed-apb2opb.c new file +5
-0+ + trace_aspeed_apb2opb_read(addr, size); + + assert(!(addr & 3)); + assert(size == 4);please fix the MemoryRegionOps definition instead.
Fixed it.
Quoted 16 lines
Quoted 16 lines
+
+ if (addr + size >sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds read: 0x%"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return 0;
+ }hw/fsi/aspeed-apb2opb.c new file +5
-0+ + return s->regs[TO_REG(addr)]; +} + +static void aspeed_apb2opb_write(void *opaque, hwaddr addr, uint64_tdata,
+ unsigned size)
Quoted 8 lines
hw/fsi/aspeed-apb2opb.c line 177
Quoted 8 lines
hw/fsi/aspeed-apb2opb.c new file +8
-0+{ + AspeedAPB2OPBState *s = ASPEED_APB2OPB(opaque); + + trace_aspeed_apb2opb_write(addr, size, data); + + assert(!(addr & 3)); + assert(size == 4); +
Fixed it.
Thanks!
~Ninad
Quoted 272 lines
Quoted 271 lines
+ if (addr + size >
sizeof(s->regs)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Out of bounds write: %"HWADDR_PRIx" for %u\n",
+__func__, addr, size);
+ return;
+ }
+
+ switch (TO_REG(addr)) {
+ caseAPB2OPB_CONTROL:
+opb_fsi_master_address(&s->opb[0], data & APB2OPB_CONTROL_OFF); + break;
+ caseAPB2OPB_OPB2FSI:
+opb_opb2fsi_address(&s->opb[0], data & APB2OPB_OPB2FSI_OFF); + break;
+ caseAPB2OPB_OPB0_WRITE_WORD_ENDIAN:
+ if (data !=APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Bridge needs to be driven as BE (0x%x)\n",
+__func__,APB2OPB_OPB0_WRITE_WORD_ENDIAN_BE); + }
+ break;
+ caseAPB2OPB_OPB0_WRITE_BYTE_ENDIAN:
+ if (data !=APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Bridge needs to be driven as BE (0x%x)\n",
+__func__,APB2OPB_OPB0_WRITE_BYTE_ENDIAN_BE); + }
+ break;
+ caseAPB2OPB_OPB0_READ_BYTE_ENDIAN:
+ if (data !=APB2OPB_OPB0_READ_WORD_ENDIAN_BE) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "%s: Bridge needs to be driven as BE (0x%x)\n",
+__func__,APB2OPB_OPB0_READ_WORD_ENDIAN_BE); + }
+ break;
+ caseAPB2OPB_TRIGGER:
+ {
+uint32_topb,op_mode,op_size,op_addr,op_data;hw/fsi/aspeed-apb2opb.c new file +21
-0+ + assert((s->regs[APB2OPB_OPB0_SEL] & APB2OPB_OPB_SEL_EN) ^ + (s->regs[APB2OPB_OPB1_SEL] & APB2OPB_OPB_SEL_EN)); + + if (s->regs[APB2OPB_OPB0_SEL] & APB2OPB_OPB_SEL_EN) { + opb = 0; + op_mode = s->regs[APB2OPB_OPB0_MODE]; + op_size = s->regs[APB2OPB_OPB0_XFER]; + op_addr = s->regs[APB2OPB_OPB0_ADDR]; + op_data = s->regs[APB2OPB_OPB0_WRITE_DATA]; + } else if (s->regs[APB2OPB_OPB1_SEL] & APB2OPB_OPB_SEL_EN) { + opb = 1; + op_mode = s->regs[APB2OPB_OPB1_MODE]; + op_size = s->regs[APB2OPB_OPB1_XFER]; + op_addr = s->regs[APB2OPB_OPB1_ADDR]; + op_data = s->regs[APB2OPB_OPB1_WRITE_DATA]; + } else { + g_assert_not_reached(); + } + + if (op_size & ~(APB2OPB_OPB_XFER_HALF |
APB2OPB_OPB_XFER_FULL)) {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "OPB transaction failed: Unrecognised access width: %d\n",
+op_size);
+ return;
+ }hw/fsi/aspeed-apb2opb.c new file +111
-0+ + op_size += 1; + + if (op_mode & APB2OPB_OPB_MODE_RD) { + int index = opb ? APB2OPB_OPB1_READ_DATA + : APB2OPB_OPB0_READ_DATA; + + switch (op_size) { + case 1: + s->regs[index] = opb_read8(&s->opb[opb], op_addr); + break; + case 2: + s->regs[index] = opb_read16(&s->opb[opb], op_addr); + break; + case 4: + s->regs[index] = opb_read32(&s->opb[opb], op_addr); + break; + default: + g_assert_not_reached(); /* should have bailed above */ + } + } else { + /* FIXME: Endian swizzling */ + switch (op_size) { + case 1: + opb_write8(&s->opb[opb], op_addr, op_data); + break; + case 2: + opb_write16(&s->opb[opb], op_addr, op_data); + break; + case 4: + opb_write32(&s->opb[opb], op_addr, op_data); + break; + default: + g_assert_not_reached(); /* should have bailed above */ + } + } + s->regs[APB2OPB_IRQ_STS] |= opb ? APB2OPB_IRQ_STS_OPB1_TX_ACK + : APB2OPB_IRQ_STS_OPB0_TX_ACK; + break; + } + } + + s->regs[TO_REG(addr)] = data; +} + +static const struct MemoryRegionOps aspeed_apb2opb_ops = { + .read = aspeed_apb2opb_read, + .write = aspeed_apb2opb_write, + .endianness = DEVICE_LITTLE_ENDIAN, +}; + +static void aspeed_apb2opb_realize (DeviceState *dev,Error **errp) +{ + SysBusDevice *sbd = SYS_BUS_DEVICE(dev); + AspeedAPB2OPBState *s = ASPEED_APB2OPB(dev); + + qbus_init(&s->opb[0], sizeof(s->opb[0]), TYPE_OP_BUS, + DEVICE(s), NULL); + qbus_init(&s->opb[1], sizeof(s->opb[1]), TYPE_OP_BUS, + DEVICE(s), NULL); + + sysbus_init_irq(sbd, &s->irq); + + memory_region_init_io(&s->iomem, OBJECT(s), &aspeed_apb2opb_ops, s, + TYPE_ASPEED_APB2OPB, 0x1000); + sysbus_init_mmio(sbd, &s->iomem); +} + +static void aspeed_apb2opb_reset (DeviceState *dev) +{ + AspeedAPB2OPBState *s = ASPEED_APB2OPB(dev); + + memset(s->regs, 0, sizeof(s->regs)); + + s->regs[APB2OPB_VERSION] = 0x000000a1; + + /* + * The following magic values came from AST2600 data sheet + * The register values are defined under section "FSI controller" + * as initial values. + */ + s->regs[APB2OPB_OPB0_WRITE_WORD_ENDIAN] = 0x0044eee4; + s->regs[APB2OPB_OPB0_WRITE_BYTE_ENDIAN] = 0x0055aaff; + s->regs[APB2OPB_OPB1_WRITE_WORD_ENDIAN] = 0x00117717; + s->regs[APB2OPB_OPB1_WRITE_BYTE_ENDIAN] = 0xffaa5500; + s->regs[APB2OPB_OPB0_READ_BYTE_ENDIAN] = 0x0044eee4; + s->regs[APB2OPB_OPB0_READ_BYTE_ENDIAN] = 0x00117717; +} + +static void aspeed_apb2opb_class_init (ObjectClass *klass,void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->desc = "ASPEED APB2OPB Bridge"; + dc->realize = aspeed_apb2opb_realize; + dc->reset = aspeed_apb2opb_reset; +} + +static const TypeInfo aspeed_apb2opb_info = { + .name = TYPE_ASPEED_APB2OPB, + .parent = TYPE_SYS_BUS_DEVICE, + .instance_size = sizeof(AspeedAPB2OPBState), + .class_init = aspeed_apb2opb_class_init, +}; + +static void aspeed_apb2opb_register_types (void ) +{ + type_register_static(&aspeed_apb2opb_info); +} + +type_init (aspeed_apb2opb_register_types);hw/fsi/meson.build +3
-3@@ -1,5 +1,6 @@ -system_ss.add(when: 'CONFIG_LBUS', if_true: files('lbus.c')) -system_ss.add(when: 'CONFIG_SCRATCHPAD', if_true: files('engine-scratchpad.c')) -system_ss.add(when: 'CONFIG_CFAM', if_true: files('cfam.c')) +system_ss.add(when: 'CONFIG_FSI_LBUS', if_true: files('lbus.c')) +system_ss.add(when: 'CONFIG_FSI_SCRATCHPAD', if_true: files('engine-scratchpad.c')) +system_ss.add(when: 'CONFIG_FSI_CFAM', if_true: files('cfam.c'))
system_ss.add(when: 'CONFIG_FSI', if_true: files('fsi.c','fsi-master.c','fsi-slave.c'))hw/fsi/meson.build +2
-1-system_ss.add(when: 'CONFIG_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_OPB', if_true: files('opb.c')) +system_ss.add(when: 'CONFIG_FSI_APB2OPB_ASPEED', if_true:files('aspeed-apb2opb.c'))
hw/fsi/trace-events +0
-0@@ -1,5 +1,6 @@
cfam_config_read(uint64_t addr, uint32_t size)"@0x%" PRIx64 " size=%d"cfam_config_write(uint64_t addr, uint32_t size, uint64_t data)"@0x%" PRIx64 " size=%d value=0x%"PRIx64 -
cfam_unimplemented_read(uint64_t addr, uint32_t size)"@0x%" PRIx64 " size=%d"cfam_unimplemented_write(uint64_t addr, uint32_t size, uint64_t data)"@0x%" PRIx64 " size=%d value=0x%"PRIx64 +aspeed_apb2opb_read(uint64_t addr,uint32_tsize) "@0x%" PRIx64 "
size=%d"
+aspeed_apb2opb_write(uint64_t addr,uint32_tsize,uint64_tdata)
"@0x%" PRIx64 " size=%d value=0x%"PRIx64hw/fsi/trace.h new file +1
-0@@ -0,0 +1 @@ +#include "trace/trace-hw_fsi.h" include/hw/fsi/aspeed-apb2opb.h new file +33
-0@@ -0,0 +1,33 @@ +/* +* SPDX-License-Identifier: GPL-2.0-or-later +* Copyright (C) 2023 IBM Corp. +* +* ASPEED APB2OPB Bridge +*/ +#ifndef FSI_ASPEED_APB2OPB_H +#define FSI_ASPEED_APB2OPB_H + +#include "hw/sysbus.h" +#include "hw/fsi/opb.h" + +#define TYPE_ASPEED_APB2OPB "aspeed.apb2opb" +OBJECT_DECLARE_SIMPLE_TYPE(AspeedAPB2OPBState, ASPEED_APB2OPB) + +#define ASPEED_APB2OPB_NR_REGS ((0xe8 >> 2) + 1) + +#define ASPEED_FSI_NUM 2 + +typedef struct AspeedAPB2OPBState { + /*< private >*/ + SysBusDevice parent_obj; + + /*< public >*/ + MemoryRegion iomem; + + uint32_t regs[ASPEED_APB2OPB_NR_REGS]; + qemu_irq irq; + + OPBus opb[ASPEED_FSI_NUM]; +}AspeedAPB2OPBState ; + +#endif /* FSI_ASPEED_APB2OPB_H */ meson.build +1
-0@@ -3244,6 +3244,7 @@ if have_system 'hw/char', 'hw/display', 'hw/dma', + 'hw/fsi', 'hw/hyperv', 'hw/i2c', 'hw/i386',
Re: [PATCH v4 07/10] hw/arm: Hook up FSI module in AST2600
In reply to Cédric Le GoaterHello Cedric,
Thanks for the review.
Quoted 102 lines · Cédric Le Goater
Quoted 101 lines · Ninad Palsule
This patchset introduces IBM's Flexible Service Interface(FSI).
Time for some fun with inter-processor buses. FSI allows a service processor access to the internal buses of a host POWER processor to perform configuration or debugging.
FSI has long existed in POWER processes and so comes with some baggage, including how it has been integrated into the ASPEED SoC.
Working backwards from the POWER processor, the fundamental pieces of interest for the implementation are:
1. The Common FRU Access Macro (CFAM), an address space containing various "engines" that drive accesses on buses internal and external to the POWER chip. Examples include the SBEFIFO and I2C masters. The engines hang off of an internal Local Bus (LBUS) which is described by the CFAM configuration block.
2. The FSI slave: The slave is the terminal point of the FSI bus for FSI symbols addressed to it. Slaves can be cascaded off of one another. The slave's configuration registers appear in address space of the CFAM to which it is attached.
3. The FSI master: A controller in the platform service processor (e.g. BMC) driving CFAM engine accesses into the POWER chip. At the hardware level FSI is a bit-based protocol supporting synchronous and DMA-driven accesses of engines in a CFAM.
4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in POWER processors. This now makes an appearance in the ASPEED SoC due to tight integration of the FSI master IP with the OPB, mainly the existence of an MMIO-mapping of the CFAM address straight onto a sub-region of the OPB address space.
5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in the AST2600. Hardware limitations prevent the OPB from being directly mapped into APB, so all accesses are indirect through the bridge.
The implementation appears as following in the qemu device tree:
(qemu) info qtree
bus: main-system-bus
type System
...
dev: aspeed.apb2opb, id ""
gpio-out "sysbus-irq" 1
mmio 000000001e79b000/0000000000001000
bus: opb.1
type opb
dev: fsi.master, id ""
bus: fsi.bus.1
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.1
type lbus
dev: scratchpad, id ""
address = 0 (0x0)
bus: opb.0
type opb
dev: fsi.master, id ""
bus: fsi.bus.0
type fsi.bus
dev: cfam.config, id ""
dev: cfam, id ""
bus: lbus.0
type lbus
dev: scratchpad, id ""
address = 0 (0x0)The LBUS is modelled to maintain the qdev bus hierarchy and to take advantage of the object model to automatically generate the CFAM configuration block. The configuration block presents engines in the order they are attached to the CFAM's LBUS. Engine implementations should subclass the LBusDevice and set the 'config' member of LBusDeviceClass to match the engine's type.
CFAM designs offer a lot of flexibility, for instance it is possible for a CFAM to be simultaneously driven from multiple FSI links. The modeling is not so complete; it's assumed that each CFAM is attached to a single FSI slave (as a consequence the CFAM subclasses the FSI slave).
As for FSI, its symbols and wire-protocol are not modelled at all. This is not necessary to get FSI off the ground thanks to the mapping of the CFAM address space onto the OPB address space - the models follow this directly and map the CFAM memory region into the OPB's memory region. Future work includes supporting more advanced accesses that drive the FSI master directly rather than indirectly via the CFAM mapping, which will require implementing the FSI state machine and methods for each of the FSI symbols on the slave. Further down the track we can also look at supporting the bitbanged SoftFSI drivers in Linux by extending the FSI slave model to resolve sequences of GPIO IRQs into FSI symbols, and calling the associated symbol method on the slave to map the access onto the CFAM.
Testing:
Tested by reading cfam config address 0 on rainier machine type.root@p10bmc:~# pdbg -a getcfam 0x0 p0: 0x0 = 0xc0022d15
Quoted 6 lines
Quoted 3 lines
Signed-off-by Andrew Jeffery <[email protected]>Signed-off-by Cédric Le Goater <[email protected]>Signed-off-by Ninad Palsule <[email protected]>you might want to add a specific fsi realize routine if extra devices need to be realized at the board level.
yes, we need to handle that once we are ready to add more devices.
Thanks!
~Ninad
Quoted 90 lines
Reviewed-by Cédric Le Goater <[email protected]>Thanks,
C.
Quoted 81 lines
---
hw/arm/aspeed_ast2600.c | 19 +++++++++++++++++++include/hw/arm/aspeed_soc.h| 4 ++++2 files changed, 23 insertions(+)hw/arm/aspeed_ast2600.c +2
-0@@ -75,6 +75,8 @@ static const hwaddr aspeed_soc_ast2600_memmap[] = { [ASPEED_DEV_UART12] = 0x1E790600, [ASPEED_DEV_UART13] = 0x1E790700, [ASPEED_DEV_VUART] = 0x1E787000, + [ASPEED_DEV_FSI1] = 0x1E79B000, + [ASPEED_DEV_FSI2] = 0x1E79B100, [ASPEED_DEV_I3C] = 0x1E7A0000, [ASPEED_DEV_SDRAM] = 0x80000000, };@@ -132,6 +134,8 @@ static const int aspeed_soc_ast2600_irqmap[] = { [ASPEED_DEV_ETH4] = 33,[ASPEED_DEV_KCS] = 138, /* 138 -> 142 */ [ASPEED_DEV_DP] = 62,
+ [ASPEED_DEV_FSI1] = 100,
+ [ASPEED_DEV_FSI2] = 101,
[ASPEED_DEV_I3C] = 102, /* 102 -> 107 */
};
@@ -262,6 +266,10 @@ static voidaspeed_soc_ast2600_init(Object *obj)object_initialize_child(obj, "emmc-boot-controller", &s->emmc_boot_controller, TYPE_UNIMPLEMENTED_DEVICE);
+
+ for (i = 0; i <ASPEED_FSI_NUM; i++) {
+object_initialize_child(obj, "fsi[*]", &s->fsi[i], TYPE_ASPEED_APB2OPB);
+ }
}
/*hw/arm/aspeed_ast2600.c +11
-0@@ -622,6 +630,17 @@ static voidaspeed_soc_ast2600_realize (DeviceState *dev, Error **errp) return; } aspeed_mmio_map(s, SYS_BUS_DEVICE(&s->sbc), 0, sc->memmap[ASPEED_DEV_SBC]); + + /* FSI */ + for (i = 0; i < ASPEED_FSI_NUM; i++) { + if (!sysbus_realize(SYS_BUS_DEVICE(&s->fsi[i]), errp)) { + return; + } + aspeed_mmio_map(s, SYS_BUS_DEVICE(&s->fsi[i]), 0, + sc->memmap[ASPEED_DEV_FSI1 + i]); + sysbus_connect_irq(SYS_BUS_DEVICE(&s->fsi[i]), 0, + aspeed_soc_get_irq(s, ASPEED_DEV_FSI1 + i)); + } } static void aspeed_soc_ast2600_class_init(ObjectClass *oc, void *data)include/hw/arm/aspeed_soc.h +4
-0@@ -36,6 +36,7 @@ #include "hw/misc/aspeed_lpc.h" #include "hw/misc/unimp.h" #include "hw/misc/aspeed_peci.h" +#include "hw/fsi/aspeed-apb2opb.h" #include "hw/char/serial.h" #define ASPEED_SPIS_NUM 2@@ -96,6 +97,7 @@ struct AspeedSoCState { UnimplementedDeviceState udc; UnimplementedDeviceState sgpiom; UnimplementedDeviceState jtag[ASPEED_JTAG_NUM]; + AspeedAPB2OPBState fsi[2]; }; #define TYPE_ASPEED_SOC "aspeed-soc"@@ -191,6 +193,8 @@ enum { ASPEED_DEV_SGPIOM, ASPEED_DEV_JTAG0, ASPEED_DEV_JTAG1, + ASPEED_DEV_FSI1, + ASPEED_DEV_FSI2, }; #define ASPEED_SOC_SPI_BOOT_ADDR 0x0