Skip to contentSkip to conversation

board: rockchip: Add Bananapi R2Pro Board

PATCH Superseded Frank Wunderlich 5 participants 6 messages Sep 20, 2023 – Oct 4, 2023

Subsystems (2)

v5 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

PATCH v5 1/1 board: rockchip: Add Bananapi R2Pro Board

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
---
v5:
- add line break in description
- reorder in makefile
- drop special dts-handling
(deletion of switchnode, disable of usb and gmac0)
- add MAINTAINERS entry
- changes to defconfig suggested by jonas
- remove "pinctrl-0 pinctrl-names" from CONFIG_OF_SPL_REMOVE_PROPS
- add CONFIG_SPL_DM_SEQ_ALIAS=y
- add CONFIG_SPL_PINCTRL=y
- remove CONFIG_USB_UHCI_HCD
- enable EFI_LOADER (defaults to y)
- drop CONFIG_SYSRESET_PSCI (reset works without)

v4:
- add r2pro board to readme
- update r2pro dts to linux version
- remove switch node from linux dts
- disable gmac0 because switch driver does not work yet
to solve timeout error:
ethernet@fe2a0000 Waiting for PHY auto negotiation to complete......... TIMEOUT! phy_startup() failed: -110FAILED: -110ethernet@fe010000 Waiting for PHY auto nee
- cleanup r2pro u-boot.dtsi like jonas suggests
- update and reorder defconfig based on jonas suggestions
- dts: disable usb_host0_ohci because of error on usb-start
scanning bus usb@fd840000 for devices...
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
- pcie is not yet working, so not adding these options rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe270000: failed to init phy (ret=-110) rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe280000: failed to init phy (ret=-110)
- emmc not tested as it is empty on my board because it breaks sdcard boot
- rename dts and defconfig (add minus sign)
- enable efi_loader in defconfig

v3:
- disable gmac0 as switch-driver is not yet ready to attach to the mac

v2:
- drop switch-node for now as u-boot driver works differently to linux

---
 arch/arm/dts/Makefile                      |   1 +
 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi |  19 +
 arch/arm/dts/rk3568-bpi-r2-pro.dts         | 852 +++++++++++++++++++++
 board/rockchip/evb_rk3568/MAINTAINERS      |   7 +
 configs/bpi-r2-pro-rk3568_defconfig        |  94 +++
 doc/board/rockchip/rockchip.rst            |   1 +
 6 files changed, 974 insertions(+)
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro.dts
 create mode 100644 configs/bpi-r2-pro-rk3568_defconfig
arch/arm/dts/Makefile +1 -0
index 85fd5b1157b1..016eb5556513 100644
@@ -177,6 +177,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
 	rk3566-soquartz-blade.dtb \
 	rk3566-soquartz-cm4.dtb \
 	rk3566-soquartz-model-a.dtb \
+	rk3568-bpi-r2-pro.dtb \
 	rk3568-evb.dtb \
 	rk3568-lubancat-2.dtb \
 	rk3568-nanopi-r5c.dtb \
arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi new file +19 -0
new file mode 100644
index 000000000000..60a3b21f2d45
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2021 Rockchip Electronics Co., Ltd
+ */
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&uart2 {
+	clock-frequency = <24000000>;
+	bootph-pre-ram;
+	status = "okay";
+};
+
arch/arm/dts/rk3568-bpi-r2-pro.dts new file +852 -0

852 lines not on this page · raw message

board/rockchip/evb_rk3568/MAINTAINERS +7 -0
index cc9eb432a8b5..8c506162c01e 100644
@@ -7,6 +7,13 @@ F:	configs/evb-rk3568_defconfig
 F:	arch/arm/dts/rk3568-evb-u-boot.dtsi
 F:	arch/arm/dts/rk3568-evb.dts
 
+Banana Pi BPI-R2 Pro
+M:	Frank Wunderlich <[email protected]>
+S:	Maintained
+F:	configs/bpi-r2-pro-rk3568_defconfig
+F:	arch/arm/dts/rk3568-bpi-r2-pro.dts
+F:	arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
+
 LUBANCAT-2
 M:	Andy Yan <[email protected]>
 S:	Maintained
configs/bpi-r2-pro-rk3568_defconfig new file +94 -0

94 lines not on this page · raw message

doc/board/rockchip/rockchip.rst +1 -0
index de9fe8e642b1..58f20b837876 100644
@@ -101,6 +101,7 @@ List of mainline supported Rockchip boards:
 
 * rk3568
      - Rockchip Evb-RK3568 (evb-rk3568)
+     - Banana Pi BPI-R2 Pro (bpi-r2-pro-rk3568)
      - EmbedFire LubanCat 2 (lubancat-2-rk3568)
      - FriendlyElec NanoPi R5C (nanopi-r5c-rk3568)
      - FriendlyElec NanoPi R5S (nanopi-r5s-rk3568)
Signature · 1 line
2.34.1
Reviewed-by on v5 1/1
#1 lore raw
Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

Quoted 4 lines

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

Thanks,
- Kever

Quoted 1,094 lines

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
---
v5:
- add line break in description
- reorder in makefile
- drop special dts-handling
(deletion of switchnode, disable of usb and gmac0)
- add MAINTAINERS entry
- changes to defconfig suggested by jonas
- remove "pinctrl-0 pinctrl-names" from CONFIG_OF_SPL_REMOVE_PROPS
- add CONFIG_SPL_DM_SEQ_ALIAS=y
- add CONFIG_SPL_PINCTRL=y
- remove CONFIG_USB_UHCI_HCD
- enable EFI_LOADER (defaults to y)
- drop CONFIG_SYSRESET_PSCI (reset works without)

v4:
- add r2pro board to readme
- update r2pro dts to linux version
- remove switch node from linux dts
- disable gmac0 because switch driver does not work yet
to solve timeout error:
ethernet@fe2a0000 Waiting for PHY auto negotiation to complete......... TIMEOUT! phy_startup() failed: -110FAILED: -110ethernet@fe010000 Waiting for PHY auto nee
- cleanup r2pro u-boot.dtsi like jonas suggests
- update and reorder defconfig based on jonas suggestions
- dts: disable usb_host0_ohci because of error on usb-start
scanning bus usb@fd840000 for devices...
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
- pcie is not yet working, so not adding these options rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe270000: failed to init phy (ret=-110) rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe280000: failed to init phy (ret=-110)
- emmc not tested as it is empty on my board because it breaks sdcard boot
- rename dts and defconfig (add minus sign)
- enable efi_loader in defconfig

v3:
- disable gmac0 as switch-driver is not yet ready to attach to the mac

v2:
- drop switch-node for now as u-boot driver works differently to linux

---
  arch/arm/dts/Makefile                      |   1 +
  arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi |  19 +
  arch/arm/dts/rk3568-bpi-r2-pro.dts         | 852 +++++++++++++++++++++
  board/rockchip/evb_rk3568/MAINTAINERS      |   7 +
  configs/bpi-r2-pro-rk3568_defconfig        |  94 +++
  doc/board/rockchip/rockchip.rst            |   1 +
  6 files changed, 974 insertions(+)

create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro.dts create mode 100644 configs/bpi-r2-pro-rk3568_defconfig

arch/arm/dts/Makefile +1 -0
index 85fd5b1157b1..016eb5556513 100644
@@ -177,6 +177,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
  	rk3566-soquartz-blade.dtb \
  	rk3566-soquartz-cm4.dtb \
  	rk3566-soquartz-model-a.dtb \
+	rk3568-bpi-r2-pro.dtb \
  	rk3568-evb.dtb \
  	rk3568-lubancat-2.dtb \
  	rk3568-nanopi-r5c.dtb \
arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi new file +19 -0
new file mode 100644
index 000000000000..60a3b21f2d45
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2021 Rockchip Electronics Co., Ltd
+ */
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&uart2 {
+	clock-frequency = <24000000>;
+	bootph-pre-ram;
+	status = "okay";
+};
+
arch/arm/dts/rk3568-bpi-r2-pro.dts new file +852 -0
new file mode 100644
index 000000000000..f9127ddfbb7d
@@ -0,0 +1,852 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Author: Frank Wunderlich <[email protected]>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Bananapi-R2 Pro (RK3568) DDR4 Board";
+	compatible = "rockchip,rk3568-bpi-r2pro", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&blue_led_pin &green_led_pin>;
+
+		blue_led: led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "off";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
+		};
+
+		green_led: led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "on";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	dc_12v: dc-12v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_receiver_pin>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	pcie30_avdd0v9: pcie30-avdd0v9-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: pcie30-avdd1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* pi6c pcie clock generator feeds both ports */
+	vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <200000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_minipcie: vcc3v3-minipcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_minipcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&minipcie_enable_h>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_ngff: vcc3v3-ngff-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_ngff";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ngffpcie_enable_h>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&combphy0 {
+	/* used for USB3 */
+	status = "okay";
+};
+
+&combphy1 {
+	/* used for USB3 */
+	status = "okay";
+};
+
+&combphy2 {
+	/* used for SATA */
+	status = "okay";
+};
+
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x0f>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+
+	snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+
+	tx_delay = <0x3c>;
+	rx_delay = <0x2f>;
+
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
+		#clock-cells = <0>;
+		clock-output-names = "rtcic_32kout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	/* pin 3 (SDA) + 4 (SCL) of header con2 */
+	status = "disabled";
+};
+
+&i2s0_8ch {
+	/* hdmi sound */
+	status = "okay";
+};
+
+&mdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "lan0";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan1";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan2";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan3";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&gmac0>;
+				phy-mode = "rgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+	};
+};
+
+&pcie30phy {
+	data-lanes = <1 2>;
+	phy-supply = <&vcc3v3_pi6c_05>;
+	status = "okay";
+};
+
+&pcie3x1 {
+	/* M.2 slot */
+	num-lanes = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&ngffpcie_reset_h>;
+	reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_ngff>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	/* mPCIe slot */
+	num-lanes = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&minipcie_reset_h>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_minipcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		blue_led_pin: blue-led-pin {
+			rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		green_led_pin: green-led-pin {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ir-receiver {
+		ir_receiver_pin: ir-receiver-pin {
+			rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		minipcie_enable_h: minipcie-enable-h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		ngffpcie_enable_h: ngffpcie-enable-h {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		minipcie_reset_h: minipcie-reset-h {
+			rockchip,pins = <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		ngffpcie_reset_h: ngffpcie-reset-h {
+			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_3v3>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&pwm8 {
+	/* fan 5v - gnd - pwm */
+	status = "okay";
+};
+
+&pwm10 {
+	/* pin 7 of header con2 */
+	status = "disabled";
+};
+
+&pwm11 {
+	/* pin 15 of header con2 */
+	status = "disabled";
+};
+
+&pwm12 {
+	/* pin 21 of header con2 */
+	/* shared with uart9 + spi3 */
+	pinctrl-0 = <&pwm12m1_pins>;
+	status = "disabled";
+};
+
+&pwm13 {
+	/* pin 24 of header con2 */
+	/* shared with uart9 */
+	pinctrl-0 = <&pwm13m1_pins>;
+	status = "disabled";
+};
+
+&pwm14 {
+	/* pin 23 of header con2 */
+	/* shared with spi3 */
+	pinctrl-0 = <&pwm14m1_pins>;
+	status = "disabled";
+};
+
+&pwm15 {
+	/* pin 19 of header con2 */
+	/* shared with spi3 */
+	pinctrl-0 = <&pwm15m1_pins>;
+	status = "disabled";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&spi3 {
+	/* pin 19 (MO) + 21 (MI) + 23 (CK) of header con2 */
+	/* shared with pwm12/14/15 and uart9 */
+	pinctrl-0 = <&spi3m1_pins>;
+	status = "disabled";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart0 {
+	/* pin 8 (TX) + 10 (RX) (RTS:16, CTS:18) of header con2 */
+	status = "disabled";
+};
+
+&uart2 {
+	/* debug-uart */
+	status = "okay";
+};
+
+&uart7 {
+	/* pin 11 (TX) + 13 (RX) of header con2 */
+	pinctrl-0 = <&uart7m1_xfer>;
+	status = "disabled";
+};
+
+&uart9 {
+	/* pin 21 (TX) + 24 (RX) of header con2 */
+	/* shared with pwm13 and pwm12/spi3 */
+	pinctrl-0 = <&uart9m1_xfer>;
+	status = "disabled";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	/* USB for PCIe/M2 */
+	status = "okay";
+};
+
+&usb2phy1_host {
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
board/rockchip/evb_rk3568/MAINTAINERS +7 -0
index cc9eb432a8b5..8c506162c01e 100644
@@ -7,6 +7,13 @@ F:	configs/evb-rk3568_defconfig
  F:	arch/arm/dts/rk3568-evb-u-boot.dtsi
  F:	arch/arm/dts/rk3568-evb.dts
 
+Banana Pi BPI-R2 Pro
+M:	Frank Wunderlich <[email protected]>
+S:	Maintained
+F:	configs/bpi-r2-pro-rk3568_defconfig
+F:	arch/arm/dts/rk3568-bpi-r2-pro.dts
+F:	arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
+
  LUBANCAT-2
  M:	Andy Yan <[email protected]>
  S:	Maintained
configs/bpi-r2-pro-rk3568_defconfig new file +94 -0
new file mode 100644
index 000000000000..5989eab569b8
@@ -0,0 +1,94 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3568-bpi-r2-pro"
+CONFIG_SYS_PROMPT="BPI-R2PRO> "
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_BOOTSTD_FULL=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_SYSBOOT=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_DWC_AHCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +1 -0
index de9fe8e642b1..58f20b837876 100644
@@ -101,6 +101,7 @@ List of mainline supported Rockchip boards:
 
  * rk3568
       - Rockchip Evb-RK3568 (evb-rk3568)
+     - Banana Pi BPI-R2 Pro (bpi-r2-pro-rk3568)
       - EmbedFire LubanCat 2 (lubancat-2-rk3568)
       - FriendlyElec NanoPi R5C (nanopi-r5c-rk3568)
       - FriendlyElec NanoPi R5S (nanopi-r5s-rk3568)
#2 lore raw

Hi

Thank you kever for review.

Tom can you take this and the depencies into next release (2024-01)?

regards Frank

Quoted 37 lines

Gesendet: Mittwoch, 27. September 2023 um 04:42 Uhr
Von: "Kever Yang" <[email protected]>
An: "Frank Wunderlich" <[email protected]>, [email protected]
Cc: "Frank Wunderlich" <[email protected]>, "Simon Glass" <[email protected]>, "Philipp Tomsich" <[email protected]>, "Joseph Chen" <[email protected]>, "Jonas Karlman" <[email protected]>
Betreff: Re: [PATCH v5] board: rockchip: Add Bananapi R2Pro Board

Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

Quoted 4 lines

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

Thanks,
- Kever

Quoted 11 lines

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/

#3 lore raw
Quoted 5 lines · Frank Wunderlich

Hi

Thank you kever for review.

Tom can you take this and the depencies into next release (2024-01)?

Kever should have these in a pull request for the next release, given the time, thanks.

Quoted 42 lines

regards Frank

Quoted 37 lines

Gesendet: Mittwoch, 27. September 2023 um 04:42 Uhr
Von: "Kever Yang" <[email protected]>
An: "Frank Wunderlich" <[email protected]>, [email protected]
Cc: "Frank Wunderlich" <[email protected]>, "Simon Glass" <[email protected]>, "Philipp Tomsich" <[email protected]>, "Joseph Chen" <[email protected]>, "Jonas Karlman" <[email protected]>
Betreff: Re: [PATCH v5] board: rockchip: Add Bananapi R2Pro Board

Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

Quoted 4 lines

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

Thanks,
- Kever

Quoted 11 lines

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/

Signature · 1 line
Tom
Reviewed-by on v5 1/1
#4 lore raw
In reply to Frank Wunderlich

Hi Frank,

Quoted 83 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
---
v5:
- add line break in description
- reorder in makefile
- drop special dts-handling
(deletion of switchnode, disable of usb and gmac0)
- add MAINTAINERS entry
- changes to defconfig suggested by jonas
- remove "pinctrl-0 pinctrl-names" from CONFIG_OF_SPL_REMOVE_PROPS
- add CONFIG_SPL_DM_SEQ_ALIAS=y
- add CONFIG_SPL_PINCTRL=y
- remove CONFIG_USB_UHCI_HCD
- enable EFI_LOADER (defaults to y)
- drop CONFIG_SYSRESET_PSCI (reset works without)

v4:
- add r2pro board to readme
- update r2pro dts to linux version
- remove switch node from linux dts
- disable gmac0 because switch driver does not work yet
to solve timeout error:
ethernet@fe2a0000 Waiting for PHY auto negotiation to complete......... TIMEOUT! phy_startup() failed: -110FAILED: -110ethernet@fe010000 Waiting for PHY auto nee
- cleanup r2pro u-boot.dtsi like jonas suggests
- update and reorder defconfig based on jonas suggestions
- dts: disable usb_host0_ohci because of error on usb-start
scanning bus usb@fd840000 for devices...
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
- pcie is not yet working, so not adding these options rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe270000: failed to init phy (ret=-110) rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe280000: failed to init phy (ret=-110)
- emmc not tested as it is empty on my board because it breaks sdcard boot
- rename dts and defconfig (add minus sign)
- enable efi_loader in defconfig

v3:
- disable gmac0 as switch-driver is not yet ready to attach to the mac

v2:
- drop switch-node for now as u-boot driver works differently to linux

---
 arch/arm/dts/Makefile                      |   1 +
 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi |  19 +
 arch/arm/dts/rk3568-bpi-r2-pro.dts         | 852 +++++++++++++++++++++
 board/rockchip/evb_rk3568/MAINTAINERS      |   7 +
 configs/bpi-r2-pro-rk3568_defconfig        |  94 +++
 doc/board/rockchip/rockchip.rst            |   1 +
 6 files changed, 974 insertions(+)
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro.dts
 create mode 100644 configs/bpi-r2-pro-rk3568_defconfig

[...]

board/rockchip/evb_rk3568/MAINTAINERS F: configs/evb-rk3568_defconfig · line 10

Quoted 9 lines
board/rockchip/evb_rk3568/MAINTAINERS +1 -0
index cc9eb432a8b5..8c506162c01e 100644
@@ -7,6 +7,13 @@ F:	configs/evb-rk3568_defconfig
 F:	arch/arm/dts/rk3568-evb-u-boot.dtsi
 F:	arch/arm/dts/rk3568-evb.dts
 
+Banana Pi BPI-R2 Pro

Maintainer entries are typically in upper case. get_maintainer.pl does not seem to mind, but use of uppercase seem to be the norm.

Quoted 17 lines
board/rockchip/evb_rk3568/MAINTAINERS +6 -0
+M:	Frank Wunderlich <[email protected]>
+S:	Maintained
+F:	configs/bpi-r2-pro-rk3568_defconfig
+F:	arch/arm/dts/rk3568-bpi-r2-pro.dts
+F:	arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
+
 LUBANCAT-2
 M:	Andy Yan <[email protected]>
 S:	Maintained
configs/bpi-r2-pro-rk3568_defconfig new file +2 -0
new file mode 100644
index 000000000000..5989eab569b8
@@ -0,0 +1,94 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y

configs/bpi-r2-pro-rk3568_defconfig line 12

Quoted 10 lines
configs/bpi-r2-pro-rk3568_defconfig new file +10 -0
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3568-bpi-r2-pro"
+CONFIG_SYS_PROMPT="BPI-R2PRO> "

Very few Rockchip boards use a custom prompt, is this needed?

Quoted 7 lines
configs/bpi-r2-pro-rk3568_defconfig new file +7 -0
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000

configs/bpi-r2-pro-rk3568_defconfig line 29

Quoted 10 lines
configs/bpi-r2-pro-rk3568_defconfig new file +10 -0
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_BOOTSTD_FULL=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro"

This is missing .dtb suffix, fdtfile env var ends up as:

fdtfile=rockchip/rk3568-bpi-r2-pro

instead of:

fdtfile=rockchip/rk3568-bpi-r2-pro.dtb

Resulting in possible a dtb-file not being loaded when an entry in extlinux.conf use fdtdir instead of fdt value.

Quoted 23 lines
configs/bpi-r2-pro-rk3568_defconfig new file +23 -0
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_SYSBOOT=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"

configs/bpi-r2-pro-rk3568_defconfig line 62

Quoted 10 lines
configs/bpi-r2-pro-rk3568_defconfig new file +10 -0
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_DWC_AHCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_SUPPORT_EMMC_BOOT=y

arch/arm/mach-rockchip/spl.c override spl_mmc_boot_mode() to always return MMCSD_MODE_RAW, so there should not be any need to include support for MMCSD_MODE_EMMCBOOT.

Quoted 4 lines
configs/bpi-r2-pro-rk3568_defconfig new file +4 -0
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y

configs/bpi-r2-pro-rk3568_defconfig line 76

Quoted 10 lines
configs/bpi-r2-pro-rk3568_defconfig new file +10 -0
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_PWM=y

Not seeing any pwm-regulator compatible in the DT, so this option could be removed.

Quoted 23 lines
configs/bpi-r2-pro-rk3568_defconfig new file +18 -0
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +0 -0
index de9fe8e642b1..58f20b837876 100644

doc/board/rockchip/rockchip.rst List of mainline supported Rockchip boards: · line 107

Quoted 7 lines
doc/board/rockchip/rockchip.rst +1 -0
@@ -101,6 +101,7 @@ List of mainline supported Rockchip boards:
 
 * rk3568
      - Rockchip Evb-RK3568 (evb-rk3568)
+     - Banana Pi BPI-R2 Pro (bpi-r2-pro-rk3568)
      - EmbedFire LubanCat 2 (lubancat-2-rk3568)
      - FriendlyElec NanoPi R5C (nanopi-r5c-rk3568)
      - FriendlyElec NanoPi R5S (nanopi-r5s-rk3568)

With CONFIG_DEFAULT_FDT_FILE fixed, this is:

remaining nits is fully up to you.

Regards,
Jonas

#5 lore raw

Hi Jonas

thanks for your review.

Quoted 103 lines

Gesendet: Dienstag, 03. Oktober 2023 um 22:27 Uhr
Von: "Jonas Karlman" <[email protected]>
An: "Frank Wunderlich" <[email protected]>, "Frank Wunderlich" <[email protected]>, "Kever Yang" <[email protected]>
Cc: "Simon Glass" <[email protected]>, "Philipp Tomsich" <[email protected]>, "Joseph Chen" <[email protected]>, [email protected]
Betreff: Re: [PATCH v5] board: rockchip: Add Bananapi R2Pro Board

Hi Frank,

Quoted 83 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Bananapi R2 Pro board.

tested:
- sdcard
- both front usb-ports
- sata
- wan-port

lan-ports are connected to mt7531 switch where driver needs to be separated from mtk ethernet-driver.

---
because iodomain is different to evb and now iodomain driver is sent as patch we need to separate between EVB and R2Pro else board can be bricked.

ethernet support depends on these series from jonas:

rockchip: Port IO-domain driver for RK3568 from linux
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
and
rockchip: Add GMAC support for RK3568 and RK3588
https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
---
v5:
- add line break in description
- reorder in makefile
- drop special dts-handling
(deletion of switchnode, disable of usb and gmac0)
- add MAINTAINERS entry
- changes to defconfig suggested by jonas
- remove "pinctrl-0 pinctrl-names" from CONFIG_OF_SPL_REMOVE_PROPS
- add CONFIG_SPL_DM_SEQ_ALIAS=y
- add CONFIG_SPL_PINCTRL=y
- remove CONFIG_USB_UHCI_HCD
- enable EFI_LOADER (defaults to y)
- drop CONFIG_SYSRESET_PSCI (reset works without)

v4:
- add r2pro board to readme
- update r2pro dts to linux version
- remove switch node from linux dts
- disable gmac0 because switch driver does not work yet
to solve timeout error:
ethernet@fe2a0000 Waiting for PHY auto negotiation to complete......... TIMEOUT! phy_startup() failed: -110FAILED: -110ethernet@fe010000 Waiting for PHY auto nee
- cleanup r2pro u-boot.dtsi like jonas suggests
- update and reorder defconfig based on jonas suggestions
- dts: disable usb_host0_ohci because of error on usb-start
scanning bus usb@fd840000 for devices...
ERROR: USB-error: DEVICENOTRESPONDING: Device did not respond to token (IN) or did not provide a handshake (OUT) (5)
unable to get device descriptor (error=-1)
- pcie is not yet working, so not adding these options rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe270000: failed to init phy (ret=-110) rockchip_pcie3phy phy@fe8c0000: lock failed 0x6890000 rockchip_pcie3phy phy@fe8c0000: PHY: Failed to init phy@fe8c0000: -110. pcie_dw_rockchip pcie@fe280000: failed to init phy (ret=-110)
- emmc not tested as it is empty on my board because it breaks sdcard boot
- rename dts and defconfig (add minus sign)
- enable efi_loader in defconfig

v3:
- disable gmac0 as switch-driver is not yet ready to attach to the mac

v2:
- drop switch-node for now as u-boot driver works differently to linux

---
 arch/arm/dts/Makefile                      |   1 +
 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi |  19 +
 arch/arm/dts/rk3568-bpi-r2-pro.dts         | 852 +++++++++++++++++++++
 board/rockchip/evb_rk3568/MAINTAINERS      |   7 +
 configs/bpi-r2-pro-rk3568_defconfig        |  94 +++
 doc/board/rockchip/rockchip.rst            |   1 +
 6 files changed, 974 insertions(+)
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
 create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro.dts
 create mode 100644 configs/bpi-r2-pro-rk3568_defconfig

[...]

Quoted 8 lines
board/rockchip/evb_rk3568/MAINTAINERS +0 -0
index cc9eb432a8b5..8c506162c01e 100644
@@ -7,6 +7,13 @@ F:	configs/evb-rk3568_defconfig
 F:	arch/arm/dts/rk3568-evb-u-boot.dtsi
 F:	arch/arm/dts/rk3568-evb.dts
 
Quoted 4 lines

board/rockchip/evb_rk3568/MAINTAINERS F: configs/evb-rk3568_defconfig · line 10

Quoted 1 line
board/rockchip/evb_rk3568/MAINTAINERS +1 -0
+Banana Pi BPI-R2 Pro

Maintainer entries are typically in upper case. get_maintainer.pl does not seem to mind, but use of uppercase seem to be the norm.

ok, i wil change it to "BANANAPI-BPI-R2-PRO" as i noticed that no spaces are in the other Boards

Quoted 21 lines
Quoted 21 lines
board/rockchip/evb_rk3568/MAINTAINERS +6 -0
+M:	Frank Wunderlich <[email protected]>
+S:	Maintained
+F:	configs/bpi-r2-pro-rk3568_defconfig
+F:	arch/arm/dts/rk3568-bpi-r2-pro.dts
+F:	arch/arm/dts/rk3568-bpi-r2-pro-u-boot.dtsi
+
 LUBANCAT-2
 M:	Andy Yan <[email protected]>
 S:	Maintained
configs/bpi-r2-pro-rk3568_defconfig new file +6 -0
new file mode 100644
index 000000000000..5989eab569b8
@@ -0,0 +1,94 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
Quoted 8 lines

configs/bpi-r2-pro-rk3568_defconfig line 12

Quoted 6 lines
configs/bpi-r2-pro-rk3568_defconfig new file +6 -0
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_DEFAULT_DEVICE_TREE="rk3568-bpi-r2-pro"
+CONFIG_SYS_PROMPT="BPI-R2PRO> "

Very few Rockchip boards use a custom prompt, is this needed?

as i use different boards here it is easier with this prompt ;)

Quoted 20 lines
Quoted 7 lines
configs/bpi-r2-pro-rk3568_defconfig new file +7 -0
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000

configs/bpi-r2-pro-rk3568_defconfig line 29

Quoted 10 lines
configs/bpi-r2-pro-rk3568_defconfig new file +10 -0
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_SIGNATURE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_BOOTSTD_FULL=y
+CONFIG_LEGACY_IMAGE_FORMAT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro"

This is missing .dtb suffix, fdtfile env var ends up as:

Quoted 8 lines

fdtfile=rockchip/rk3568-bpi-r2-pro

instead of:

fdtfile=rockchip/rk3568-bpi-r2-pro.dtb

Resulting in possible a dtb-file not being loaded when an entry in extlinux.conf use fdtdir instead of fdt value.

ok, will fix it to

CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-bpi-r2-pro.dtb"

Quoted 29 lines
Quoted 29 lines
configs/bpi-r2-pro-rk3568_defconfig new file +29 -0
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_SYSBOOT=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_DWC_AHCI=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
Quoted 8 lines

configs/bpi-r2-pro-rk3568_defconfig line 62

Quoted 4 lines
configs/bpi-r2-pro-rk3568_defconfig new file +4 -0
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_SUPPORT_EMMC_BOOT=y

arch/arm/mach-rockchip/spl.c override spl_mmc_boot_mode() to always return MMCSD_MODE_RAW, so there should not be any need to include support for MMCSD_MODE_EMMCBOOT.

i would leave it till i known how to correctly boot from emmc and how to determine from which mmc device board was booted.

Quoted 9 lines
Quoted 9 lines
configs/bpi-r2-pro-rk3568_defconfig new file +9 -0
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_DWC_ETH_QOS_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
Quoted 8 lines

configs/bpi-r2-pro-rk3568_defconfig line 76

Quoted 5 lines
configs/bpi-r2-pro-rk3568_defconfig new file +5 -0
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_PWM=y

Not seeing any pwm-regulator compatible in the DT, so this option could be removed.

ok, i drop it

Quoted 33 lines
Quoted 23 lines
configs/bpi-r2-pro-rk3568_defconfig new file +18 -0
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_SCSI=y
+CONFIG_DM_SCSI=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_ERRNO_STR=y
doc/board/rockchip/rockchip.rst +0 -0
index de9fe8e642b1..58f20b837876 100644

doc/board/rockchip/rockchip.rst List of mainline supported Rockchip boards: · line 107

Quoted 7 lines
doc/board/rockchip/rockchip.rst +1 -0
@@ -101,6 +101,7 @@ List of mainline supported Rockchip boards:
 
 * rk3568
      - Rockchip Evb-RK3568 (evb-rk3568)
+     - Banana Pi BPI-R2 Pro (bpi-r2-pro-rk3568)
      - EmbedFire LubanCat 2 (lubancat-2-rk3568)
      - FriendlyElec NanoPi R5C (nanopi-r5c-rk3568)
      - FriendlyElec NanoPi R5S (nanopi-r5s-rk3568)

With CONFIG_DEFAULT_FDT_FILE fixed, this is:

Quoted 3 lines

remaining nits is fully up to you.

regards Frank