i2c: muxes: pca954x: Enable features on MAX7357/MAX7358
Subsystems (2)
PATCH RESEND v3 2/2 i2c: muxes: pca954x: Enable features on MAX7357/MAX7358
From: Patrick Rudolph <[email protected]>
Detect that max7357 is being used and run custom init sequence. Enable additional features based on DT settings and unconditionally release the shared interrupt pin after 1.6 seconds and allow to use it as reset.
These features aren't enabled by default & its up to board designer to enable the same as it may have unexpected side effects.
These should be validated for proper functioning & detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.
The init sequence is not run for max7358 that needs to be unlocked first, but that would need the unimplemented function i2c_probe_func_quick_write().
---
Changes in V3:
- Delete unused #define
- Update pca954x_init
- Update commit message
Changes in V2:
- Update comments
- Update check for DT properties
--- drivers/i2c/muxes/i2c-mux-pca954x.c | 38 ++++++++++++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)
drivers/i2c/muxes/i2c-mux-pca954x.c +37 -1
@@ -57,6 +57,20 @@#define PCA954X_IRQ_OFFSET 4 +/* +* MAX7357's configuration register is writeable after POR, but +* can be locked by setting the basic mode bit. MAX7358 configuration +* register is locked by default and needs to be unlocked first. +* The configuration register holds the following settings: +*/ +#define MAX7357_CONF_INT_ENABLE BIT(0) +#define MAX7357_CONF_FLUSH_OUT BIT(1) +#define MAX7357_CONF_RELEASE_INT BIT(2) +#define MAX7357_CONF_DISCON_SINGLE_CHAN BIT(4) +#define MAX7357_CONF_PRECONNECT_TEST BIT(7) + +#define MAX7357_POR_DEFAULT_CONF BIT(0) +enum pca_type { max_7356, max_7357,
@@ -463,6 +477,7 @@ static void pca954x_cleanup(struct i2c_mux_core *muxc)static int pca954x_init (struct i2c_client *client,struct pca954x *data) { +u8 conf =MAX7357_POR_DEFAULT_CONF ;int ret;if (data->idle_state >=0 )
@@ -470,7 +485,28 @@ static int pca954x_init(struct i2c_client *client, struct pca954x *data)else data->last_chan =0 ;/* Disconnect multiplexer */ - ret =i2c_smbus_write_byte (client, data->last_chan); +if (device_is_compatible (&client->dev,"maxim,max7357" ) && +i2c_check_functionality (client->adapter,I2C_FUNC_SMBUS_WRITE_BYTE_DATA )) { +/* +* The interrupt signal is shared with the reset pin. Release the +* interrupt after 1.6 seconds to allow using the pin as reset. +* The interrupt isn't serviced yet. +*/ + conf |=MAX7357_CONF_RELEASE_INT ; + +if (device_property_read_bool (&client->dev,"maxim,isolate-stuck-channel" )) + conf |=MAX7357_CONF_DISCON_SINGLE_CHAN ; +if (device_property_read_bool (&client->dev,"maxim,send-flush-out-sequence" )) + conf |=MAX7357_CONF_FLUSH_OUT ; +if (device_property_read_bool (&client->dev, +"maxim,preconnection-wiggle-test-enable" )) + conf |=MAX7357_CONF_PRECONNECT_TEST ; + + ret =i2c_smbus_write_byte_data (client, data->last_chan, conf); + }else { + ret =i2c_smbus_write_byte (client, data->last_chan); + } +if (ret <0 ) data->last_chan =0 ;
Signature · 1 line
2.41.0
Hi!
Sorry for being unresponsive...
The subject, description and the bindings patch talk about MAX7358, but since it not actually handled it is misleading for the subject to say that features are enabled on MAX7358.
Quoted 10 lines · Naresh Solanki
From: Patrick Rudolph <[email protected]>
Detect that max7357 is being used and run custom init sequence. Enable additional features based on DT settings and unconditionally release the shared interrupt pin after 1.6 seconds and allow to use it as reset.
These features aren't enabled by default & its up to board designer to enable the same as it may have unexpected side effects.
Quoted 6 lines
These should be validated for proper functioning & detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.
The init sequence is not run for max7358 that needs to be unlocked first, but that would need the unimplemented function
i2c_probe_func_quick_write().
Is that correct? If that is all that missing, why is it not sufficient to open-code it instead?
i2c_smbus_xfer(client->adapter, client->addr, client->flags, I2C_SMBUS_WRITE, 0, I2C_SMBUS_QUICK, NULL);
Quoted 21 lines
Signed-off-by Patrick Rudolph <[email protected]>Signed-off-by Naresh Solanki <[email protected]>---
Changes in V3:
- Delete unused #define
- Updatepca954x_init
- Update commit messageChanges in V2:
- Update comments
- Update check for DT properties--- drivers/i2c/muxes/i2c-mux-pca954x.c | 38 ++++++++++++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)drivers/i2c/muxes/i2c-mux-pca954x.c +0
-0
drivers/i2c/muxes/i2c-mux-pca954x.c line 66
Quoted 10 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +7
-0@@ -57,6 +57,20 @@#define PCA954X_IRQ_OFFSET 4 +/* +* MAX7357's configuration register is writeable after POR, but +* can be locked by setting the basic mode bit. MAX7358 configuration +* register is locked by default and needs to be unlocked first. +* The configuration register holds the following settings: +*/ +#define MAX7357_CONF_INT_ENABLE BIT(0)
This define isn't used.
Quoted 11 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +7
-0+#define MAX7357_CONF_FLUSH_OUT BIT(1) +#define MAX7357_CONF_RELEASE_INT BIT(2) +#define MAX7357_CONF_DISCON_SINGLE_CHAN BIT(4) +#define MAX7357_CONF_PRECONNECT_TEST BIT(7) + +#define MAX7357_POR_DEFAULT_CONF BIT(0) +enum pca_type { max_7356, max_7357,
drivers/i2c/muxes/i2c-mux-pca954x.c static void pca954x_cleanup(struct i2c_mux_core *muxc) · line 480
Quoted 4 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +1
-0@@ -463,6 +477,7 @@ static void pca954x_cleanup(struct i2c_mux_core *muxc)static int pca954x_init (struct i2c_client *client,struct pca954x *data) { +u8 conf =MAX7357_POR_DEFAULT_CONF ;
This line can be moved inside the block below handling max7357. The POR default conf is not the same for max7358 anyway.
drivers/i2c/muxes/i2c-mux-pca954x.c static int pca954x_init(struct i2c_client *client, struct pca954x *data) · line 489
Quoted 10 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +2
-1int ret;if (data->idle_state >=0 )@@ -470,7 +485,28 @@ static int pca954x_init(struct i2c_client *client, struct pca954x *data)else data->last_chan =0 ;/* Disconnect multiplexer */ - ret =i2c_smbus_write_byte (client, data->last_chan); +if (device_is_compatible (&client->dev,"maxim,max7357" ) && +i2c_check_functionality (client->adapter,I2C_FUNC_SMBUS_WRITE_BYTE_DATA )) {
I would have liked a message that any requested extra features cannot be enabled if the chip happens to be connected to a bus not capable of ...write_byte_data(). That might be plenty helpful for anybody who happens to find themself in that hole...
Quoted 13 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +13
-0+/* +* The interrupt signal is shared with the reset pin. Release the +* interrupt after 1.6 seconds to allow using the pin as reset. +* The interrupt isn't serviced yet. +*/ + conf |=MAX7357_CONF_RELEASE_INT ; + +if (device_property_read_bool (&client->dev,"maxim,isolate-stuck-channel" )) + conf |=MAX7357_CONF_DISCON_SINGLE_CHAN ; +if (device_property_read_bool (&client->dev,"maxim,send-flush-out-sequence" )) + conf |=MAX7357_CONF_FLUSH_OUT ; +if (device_property_read_bool (&client->dev, +"maxim,preconnection-wiggle-test-enable" ))
drivers/i2c/muxes/i2c-mux-pca954x.c static int pca954x_init(struct i2c_client *client, struct pca954x *data) · line 512
Quoted 10 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +7
-0+ conf |=MAX7357_CONF_PRECONNECT_TEST ; + + ret =i2c_smbus_write_byte_data (client, data->last_chan, conf); + }else { + ret =i2c_smbus_write_byte (client, data->last_chan); + } +if (ret <0 ) data->last_chan =0 ;
Would there be any point in configuring max7357 to be in basic mode?
Cheers,
Peter
Hi Peter,
Quoted 8 lines · Peter Rosin
Hi!
Sorry for being unresponsive...
The subject, description and the bindings patch talk about MAX7358, but since it not actually handled it is misleading for the subject to say that features are enabled on MAX7358.
Yes will remove reference to max7358.
Quoted 19 lines
Quoted 10 lines · Naresh Solanki
From: Patrick Rudolph <[email protected]>
Detect that max7357 is being used and run custom init sequence. Enable additional features based on DT settings and unconditionally release the shared interrupt pin after 1.6 seconds and allow to use it as reset.
These features aren't enabled by default & its up to board designer to enable the same as it may have unexpected side effects.
Quoted 6 lines
These should be validated for proper functioning & detection of devices in secondary bus as sometimes it can cause secondary bus being disabled.
The init sequence is not run for max7358 that needs to be unlocked first, but that would need the unimplemented function
i2c_probe_func_quick_write().
Quoted 5 lines
Is that correct? If that is all that missing, why is it not sufficient to open-code it instead?
i2c_smbus_xfer(client->adapter, client->addr, client->flags, I2C_SMBUS_WRITE, 0, I2C_SMBUS_QUICK, NULL);
will drop max7358 for now in this patch series.
Quoted 25 lines
Quoted 25 lines
Signed-off-by Patrick Rudolph <[email protected]>Signed-off-by Naresh Solanki <[email protected]>---
Changes in V3:
- Delete unused #define
- Updatepca954x_init
- Update commit messageChanges in V2:
- Update comments
- Update check for DT properties--- drivers/i2c/muxes/i2c-mux-pca954x.c | 38 ++++++++++++++++++++++++++++- 1 file changed, 37 insertions(+), 1 deletion(-)drivers/i2c/muxes/i2c-mux-pca954x.c +0
-0@@ -57,6 +57,20 @@#define PCA954X_IRQ_OFFSET 4
Quoted 9 lines
drivers/i2c/muxes/i2c-mux-pca954x.c line 66
Quoted 7 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +7
-0+/* +* MAX7357's configuration register is writeable after POR, but +* can be locked by setting the basic mode bit. MAX7358 configuration +* register is locked by default and needs to be unlocked first. +* The configuration register holds the following settings: +*/ +#define MAX7357_CONF_INT_ENABLE BIT(0)This define isn't used.
Its indirectly used for default POR config. Will use it there.
Quoted 13 lines
Quoted 13 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +7
-0+#define MAX7357_CONF_FLUSH_OUT BIT(1) +#define MAX7357_CONF_RELEASE_INT BIT(2) +#define MAX7357_CONF_DISCON_SINGLE_CHAN BIT(4) +#define MAX7357_CONF_PRECONNECT_TEST BIT(7) + +#define MAX7357_POR_DEFAULT_CONF BIT(0) +enum pca_type { max_7356, max_7357,@@ -463,6 +477,7 @@ static void pca954x_cleanup(struct i2c_mux_core *muxc)
Quoted 6 lines
drivers/i2c/muxes/i2c-mux-pca954x.c static void pca954x_cleanup(struct i2c_mux_core *muxc) · line 480
Quoted 3 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +1
-0static int pca954x_init (struct i2c_client *client,struct pca954x *data) { +u8 conf =MAX7357_POR_DEFAULT_CONF ;This line can be moved inside the block below handling max7357. The POR default conf is not the same for max7358 anyway.
Sure.
Quoted 8 lines
Quoted 8 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +0
-0int ret;if (data->idle_state >=0 )@@ -470,7 +485,28 @@ static int pca954x_init(struct i2c_client *client, struct pca954x *data)else data->last_chan =0 ;/* Disconnect multiplexer */
Quoted 8 lines
drivers/i2c/muxes/i2c-mux-pca954x.c static int pca954x_init(struct i2c_client *client, struct pca954x *data) · line 489
Quoted 3 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +2
-1- ret =i2c_smbus_write_byte (client, data->last_chan); +if (device_is_compatible (&client->dev,"maxim,max7357" ) && +i2c_check_functionality (client->adapter,I2C_FUNC_SMBUS_WRITE_BYTE_DATA )) {I would have liked a message that any requested extra features cannot be enabled if the chip happens to be connected to a bus not capable of ...write_byte_data(). That might be plenty helpful for anybody who happens to find themself in that hole...
Sure will add that.
Quoted 18 lines
Quoted 18 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +17
-0+/* +* The interrupt signal is shared with the reset pin. Release the +* interrupt after 1.6 seconds to allow using the pin as reset. +* The interrupt isn't serviced yet. +*/ + conf |=MAX7357_CONF_RELEASE_INT ; + +if (device_property_read_bool (&client->dev,"maxim,isolate-stuck-channel" )) + conf |=MAX7357_CONF_DISCON_SINGLE_CHAN ; +if (device_property_read_bool (&client->dev,"maxim,send-flush-out-sequence" )) + conf |=MAX7357_CONF_FLUSH_OUT ; +if (device_property_read_bool (&client->dev, +"maxim,preconnection-wiggle-test-enable" )) + conf |=MAX7357_CONF_PRECONNECT_TEST ; + + ret =i2c_smbus_write_byte_data (client, data->last_chan, conf); + }else {
Quoted 8 lines
drivers/i2c/muxes/i2c-mux-pca954x.c static int pca954x_init(struct i2c_client *client, struct pca954x *data) · line 512
Quoted 6 lines
drivers/i2c/muxes/i2c-mux-pca954x.c +3
-0+ ret =i2c_smbus_write_byte (client, data->last_chan); + } +if (ret <0 ) data->last_chan =0 ;Would there be any point in configuring max7357 to be in basic mode?
If the above features arent needed then basic mode will serve the purpose.
Quoted 3 lines
Cheers,
Peter