Skip to contentSkip to conversation

sunxi: H616: add LPDDR4 support

PATCH Superseded Mikhail Kalashnikov 2 participants 5 messages Nov 4, 2023 – Nov 11, 2023

Subsystems (3)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
maintainer
#2 lore raw

Re: [PATCH v3 1/1] sunxi: H616: add LPDDR4 DRAM support

In reply to Mikhail Kalashnikov

Hi Mikhail,

I have some notes on LPDDR4 from a long time ago. It mostly matches to your code, but please take a look at comments below.

Note that I have extra code, not included in this patch, for mctl_phy_read_training(). At the very beginning, before any other register access is done, this should be added:

if (para->type == SUNXI_DRAM_TYPE_LPDDR4) {
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x800);
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x81c);
}

Maybe that will help with other LPDDR4 boards?

Quoted 105 lines · CET Mikhail Kalashnikov

From: iuncuim <[email protected]>

The H616 SoC family has support for several types of DRAM: DDR3, LPDDR3, DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 and LPDDR3 memory. Let's extend the driver to support the LPDDR4 memory. This type of memory widely used in device with T507(-H) SoC and new orangepi zero3 with H618.
The compatibility with T507 is not yet complete, because there is difference in the phy_init array.
The LPDDR4-2133 timings correspond to DRAM Rayson RS1G32LO4D2BDS-53BT found on the NOR SPI from the Orangepi Zero 3 4GB.

---
 .../include/asm/arch-sunxi/dram_sun50i_h616.h |   2 +
 arch/arm/mach-sunxi/Kconfig                   |  17 ++
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 197 ++++++++++++++----
 arch/arm/mach-sunxi/dram_timings/Makefile     |   1 +
 .../dram_timings/h616_lpddr4_2133.c           |  95 +++++++++
 5 files changed, 277 insertions(+), 35 deletions(-)
 create mode 100644 arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c
(quoted diff) +0 -0

b/arch/arm/include/asm/arch-sunxi/dram_sun50i_h616.h index 11774deded..a8fdda124a 100644

arch/arm/include/asm/arch-sunxi/dram_sun50i_h616.h +2 -0
@@ -130,6 +130,7 @@ check_member(sunxi_mctl_ctl_reg, unk_0x4240, 0x4240);
 #define MSTR_DEVICETYPE_LPDDR2	BIT(2)
 #define MSTR_DEVICETYPE_LPDDR3	BIT(3)
 #define MSTR_DEVICETYPE_DDR4	BIT(4)
+#define MSTR_DEVICETYPE_LPDDR4	BIT(5)
 #define MSTR_DEVICETYPE_MASK	GENMASK(5, 0)
 #define MSTR_2TMODE		BIT(10)
 #define MSTR_BUSWIDTH_FULL	(0 << 12)
@@ -154,6 +155,7 @@ struct dram_para {
 	u32 odt_en;
 	u32 tpr0;
 	u32 tpr2;
+	u32 tpr6;
 	u32 tpr10;
 	u32 tpr11;
 	u32 tpr12;
arch/arm/mach-sunxi/Kconfig +17 -0
index 9d5df2c102..e65bcb36a2 100644
@@ -85,6 +85,12 @@ config DRAM_SUN50I_H616_TPR2
 	help
 	  TPR2 value from vendor DRAM settings.
 
+config DRAM_SUN50I_H616_TPR6
+	hex "H616 DRAM TPR6 parameter"
+	default 0x3300c080
+	help
+	  TPR6 value from vendor DRAM settings.
+
 config DRAM_SUN50I_H616_TPR10
 	hex "H616 DRAM TPR10 parameter"
 	help
@@ -441,6 +447,9 @@ config SUNXI_DRAM_DDR2
 config SUNXI_DRAM_LPDDR3
 	bool
 
+config SUNXI_DRAM_LPDDR4
+	bool
+
 choice
 	prompt "DRAM Type and Timing"
 	default SUNXI_DRAM_DDR3_1333 if !MACH_SUN8I_V3S
@@ -484,6 +493,14 @@ config SUNXI_DRAM_H616_LPDDR3
 	  This option is the LPDDR3 timing used by the stock boot0 by
 	  Allwinner.
 
+config SUNXI_DRAM_H616_LPDDR4
+	bool "LPDDR4 DRAM chips on the H616 DRAM controller"
+	select SUNXI_DRAM_LPDDR4
+	depends on DRAM_SUN50I_H616
+	help
+	  This option is the LPDDR4 timing used by the stock boot0 by
+	  Allwinner.
+
 config SUNXI_DRAM_H616_DDR3_1333
 	bool "DDR3-1333 boot0 timings on the H616 DRAM controller"
 	select SUNXI_DRAM_DDR3
(quoted diff) +0 -0

b/arch/arm/mach-sunxi/dram_sun50i_h616.c index ba5659d409..185f35850a 100644

arch/arm/mach-sunxi/dram_sun50i_h616.c +5 -0
@@ -238,6 +238,11 @@ static const u8 phy_init[] = {
 	0x08, 0x01, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
 	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
 	0x17, 0x19, 0x1a
+#elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR4)
+	0x02, 0x00, 0x17, 0x05, 0x04, 0x19, 0x06, 0x07,
+	0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+	0x18, 0x03, 0x1a
 #endif
 };
 

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_configure_odt(const struct · line 257

Quoted 7 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -0
@@ -246,8 +251,13 @@ static void mctl_phy_configure_odt(const struct
 dram_para *para) {
 	uint32_t val_lo, val_hi;
 
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x390, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x3d0, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x410, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x450, BIT(5), BIT(4));

I don't have above block. Something from newer libdram? Is it applicable to all DRAM types?

Quoted 12 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +2 -1
+
 	val_lo = para->dx_dri;
-	val_hi = para->dx_dri;
+	val_hi = (para->type == SUNXI_DRAM_TYPE_LPDDR4) ? 0x04040404 :

para->dx_dri; writel_relaxed(MASK_BYTE(val_lo, 0), SUNXI_DRAM_PHY0_BASE + 0x388); writel_relaxed(MASK_BYTE(val_hi, 0), SUNXI_DRAM_PHY0_BASE + 0x38c); writel_relaxed(MASK_BYTE(val_lo, 1), SUNXI_DRAM_PHY0_BASE + 0x3c8); @@ -265,7 +275,7 @@ static void mctl_phy_configure_odt(const struct dram_para *para) writel_relaxed(MASK_BYTE(val_hi, 1), SUNXI_DRAM_PHY0_BASE + 0x34c);

val_lo = (para->type == SUNXI_DRAM_TYPE_LPDDR3) ? 0 : para-
dx_odt;

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_configure_odt(const struct dram_para *para)

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +1 -1
-	val_hi = para->dx_odt;
+	val_hi = (para->type == SUNXI_DRAM_TYPE_LPDDR4) ? 0 : para->dx_odt;
 	writel_relaxed(MASK_BYTE(val_lo, 0), SUNXI_DRAM_PHY0_BASE + 

0x380);

Quoted 1 line

writel_relaxed(MASK_BYTE(val_hi, 0), SUNXI_DRAM_PHY0_BASE +

0x384);

Quoted 1 line

writel_relaxed(MASK_BYTE(val_lo, 1), SUNXI_DRAM_PHY0_BASE +

0x3c0);

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_bit_delay_compensation(const struct · line 592

Quoted 6 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +2 -0
@@ -578,6 +588,8 @@ static void mctl_phy_bit_delay_compensation(const struct
 dram_para *para) clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x60, 1);
 		setbits_le32(SUNXI_DRAM_PHY0_BASE + 8, 8);
 		clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x190, 0x10);
+		if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
+			clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x4, 

0x80);

Quoted 169 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +71 -25
 		if (para->tpr10 & BIT(30))
 			val = para->tpr11 & 0x3f;
@@ -791,8 +803,9 @@ static void mctl_phy_ca_bit_delay_compensation(const
 struct dram_para *para, writel(val, SUNXI_DRAM_PHY0_BASE + 0x7e0);
 	writel(val, SUNXI_DRAM_PHY0_BASE + 0x7f4);
 
-	if (para->type == SUNXI_DRAM_TYPE_DDR3) {
-		val = (para->tpr10 >> 7) & 0x1e;
+	val = (para->tpr10 >> 7) & 0x1e;
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
 		if (para->tpr2 & 1) {
 			writel(val, SUNXI_DRAM_PHY0_BASE + 0x794);
 			if (config->ranks == 2) {
@@ -818,8 +831,8 @@ static void mctl_phy_ca_bit_delay_compensation(const
 struct dram_para *para, writel(val, SUNXI_DRAM_PHY0_BASE + 0x7b8);
 			}
 		}
-	} else if (para->type == SUNXI_DRAM_TYPE_LPDDR3) {
-		val = (para->tpr10 >> 7) & 0x1e;
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
 		if (para->tpr2 & 1) {
 			writel(val, SUNXI_DRAM_PHY0_BASE + 0x7a0);
 			if (config->ranks == 2) {
@@ -833,7 +846,18 @@ static void mctl_phy_ca_bit_delay_compensation(const
 struct dram_para *para, writel(val, SUNXI_DRAM_PHY0_BASE + 0x7f8);
 			}
 		}
-	}
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		if (para->tpr2 & 1) {
+			writel(val, SUNXI_DRAM_PHY0_BASE + 0x788);
+		} else {
+			writel(val, SUNXI_DRAM_PHY0_BASE + 0x794);
+		};
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 }
 
 static bool mctl_phy_init(const struct dram_para *para,
@@ -846,30 +870,42 @@ static bool mctl_phy_init(const struct dram_para
 *para, u32 val, val2, *ptr, mr0, mr2;
 	int i;
 
+	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
+		clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x4,0x80);
+
 	if (config->bus_full_width)
 		val = 0xf;
 	else
 		val = 3;
 	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x3c, 0xf, val);
 
-	if (para->tpr2 & 0x100) {
-		if (para->type == SUNXI_DRAM_TYPE_DDR3) {
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
+		if (para->tpr2 & 0x100) {
 			val = 9;
 			val2 = 7;
-		} else if (para->type == SUNXI_DRAM_TYPE_LPDDR3) {
-			// untested setup: use some values for now
-			val = 14;
-			val2 = 8;
-		}
-	} else {
-		if (para->type == SUNXI_DRAM_TYPE_DDR3) {
+		} else {
 			val = 13;
 			val2 = 9;
-		} else if (para->type == SUNXI_DRAM_TYPE_LPDDR3) {
+		}
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
+		if (para->tpr2 & 0x100) {
+			val = 12;
+			val2 = 6;
+		} else {
 			val = 14;
 			val2 = 8;
 		}
-	}
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		val = 20;
+		val2 = 10;
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 
 	writel(val, SUNXI_DRAM_PHY0_BASE + 0x14);
 	writel(val, SUNXI_DRAM_PHY0_BASE + 0x35c);
@@ -893,19 +929,40 @@ static bool mctl_phy_init(const struct dram_para
 *para, if (para->tpr10 & TPR10_CA_BIT_DELAY)
 		mctl_phy_ca_bit_delay_compensation(para, config);
 
-	if (para->type == SUNXI_DRAM_TYPE_DDR3)
-		val = 0x80;
-	else if (para->type == SUNXI_DRAM_TYPE_LPDDR3)
-		val = 0xc0;
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
+		val = para->tpr6 & 0xff;
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
+		val = para->tpr6 >> 8 & 0xff;
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		val = para->tpr6 >> 24 & 0xff;
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
+
 	writel(val, SUNXI_DRAM_PHY0_BASE + 0x3dc);
 	writel(val, SUNXI_DRAM_PHY0_BASE + 0x45c);
 
 	mctl_phy_configure_odt(para);
 
-	if (para->type == SUNXI_DRAM_TYPE_DDR3)
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
 		val = 0x0a;
-	else if (para->type == SUNXI_DRAM_TYPE_LPDDR3)
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
 		val = 0x0b;
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		val = 0x0d;
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 4, 0x7, val);
 
 	if (para->clk <= 672)
@@ -955,8 +1012,8 @@ static bool mctl_phy_init(const struct dram_para *para,
 mr0 = 0x1f14;
 		mr2 = 0x20;
 	}
-
-	if (para->type == SUNXI_DRAM_TYPE_DDR3) {
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
 		writel(mr0, &mctl_ctl->mrctrl1);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
@@ -972,7 +1029,8 @@ static bool mctl_phy_init(const struct dram_para *para,
 writel(0, &mctl_ctl->mrctrl1);
 		writel(0x80003030, &mctl_ctl->mrctrl0);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
-	} else if (para->type == SUNXI_DRAM_TYPE_LPDDR3) {
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
 		writel(mr0, &mctl_ctl->mrctrl1);
 		writel(0x800000f0, &mctl_ctl->mrctrl0);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_phy_init(const struct dram_para · line 1053

Quoted 9 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +5 -1
@@ -988,7 +1046,48 @@ static bool mctl_phy_init(const struct dram_para
 *para, writel(0x301, &mctl_ctl->mrctrl1);
 		writel(0x800000f0, &mctl_ctl->mrctrl0);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
-	}
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		writel(0x0, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);

I don't have above block. Maybe difference from newer version of libdram code?

Quoted 52 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +39 -0
+
+		writel(0x134, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0x21b, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0x333, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0x403, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0xb04, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0xc72, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0xe09, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+		writel(0x1624, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 
 	writel(0, SUNXI_DRAM_PHY0_BASE + 0x54);
 
@@ -1057,17 +1156,29 @@ static bool mctl_ctrl_init(const struct dram_para
 *para,
 
 	setbits_le32(&mctl_com->unk_0x008, 0xff00);
 
+	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
+		writel(1, SUNXI_DRAM_COM_BASE + 0x50);
 	clrsetbits_le32(&mctl_ctl->sched[0], 0xff00, 0x3000);
 
 	writel(0, &mctl_ctl->hwlpctl);
 
 	setbits_le32(&mctl_com->unk_0x008, 0xff00);

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_ctrl_init(const struct dram_para · line 1171

Quoted 10 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -5
 
-	reg_val = MSTR_BURST_LENGTH(8) | MSTR_ACTIVE_RANKS(config->ranks);
-	if (para->type == SUNXI_DRAM_TYPE_DDR3)
-		reg_val |= MSTR_DEVICETYPE_DDR3 | MSTR_2TMODE;
-	else if (para->type == SUNXI_DRAM_TYPE_LPDDR3)
-		reg_val |= MSTR_DEVICETYPE_LPDDR3;
+	reg_val = MSTR_ACTIVE_RANKS(config->ranks);
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
+		reg_val |= MSTR_BURST_LENGTH(8) | MSTR_DEVICETYPE_DDR3 | 

MSTR_2TMODE;

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_ca_bit_delay_compensation(const struct dram_para *para,

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +3 -0
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
+		reg_val |= MSTR_BURST_LENGTH(8) | 

MSTR_DEVICETYPE_LPDDR3;

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_ca_bit_delay_compensation(const struct dram_para *para,

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +3 -0
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		reg_val |= MSTR_BURST_LENGTH(16) | 

MSTR_DEVICETYPE_LPDDR4;

Quoted 21 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +5 -0
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 	if (config->bus_full_width)
 		reg_val |= MSTR_BUSWIDTH_FULL;
arch/arm/mach-sunxi/dram_sun50i_h616.c +5 -2
 	else
@@ -1079,10 +1190,20 @@ static bool mctl_ctrl_init(const struct dram_para
 *para, else
 		writel(0x0201, &mctl_ctl->odtmap);
 
-	if (para->type == SUNXI_DRAM_TYPE_DDR3)
+	switch (para->type) {
+	case SUNXI_DRAM_TYPE_DDR3:
 		reg_val = 0x06000400;
-	else if (para->type == SUNXI_DRAM_TYPE_LPDDR3)
+		break;
+	case SUNXI_DRAM_TYPE_LPDDR3:
 		reg_val = 0x09020400;
+		break;

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_ctrl_init(const struct dram_para · line 1209

Quoted 10 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +7 -0
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		reg_val = 0x04000400;
+		break;
+	case SUNXI_DRAM_TYPE_DDR4:
+	default:
+		panic("This DRAM setup is currently not supported.\n");
+	};
 	writel(reg_val, &mctl_ctl->odtcfg);
 	writel(reg_val, &mctl_ctl->unk_0x2240);
 	writel(reg_val, &mctl_ctl->unk_0x3240);

I have extra "writel(BIT(31), &mctl_com->cr);" after this block for all DRAM types. Not sure if it changes anything.

Quoted 52 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +6 -0
@@ -1102,6 +1223,9 @@ static bool mctl_ctrl_init(const struct dram_para
 *para, setbits_le32(&mctl_ctl->unk_0x3180, BIT(31) | BIT(30));
 	setbits_le32(&mctl_ctl->unk_0x4180, BIT(31) | BIT(30));
 
+	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
+		setbits_le32(&mctl_ctl->dbictl, 1);
+
 	setbits_le32(&mctl_ctl->rfshctl3, BIT(0));
 	clrbits_le32(&mctl_ctl->dfimisc, BIT(0));
 
@@ -1224,6 +1348,8 @@ static const struct dram_para para = {
 	.type = SUNXI_DRAM_TYPE_DDR3,
 #elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR3)
 	.type = SUNXI_DRAM_TYPE_LPDDR3,
+#elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR4)
+	.type = SUNXI_DRAM_TYPE_LPDDR4,
 #endif
 	.dx_odt = CONFIG_DRAM_SUN50I_H616_DX_ODT,
 	.dx_dri = CONFIG_DRAM_SUN50I_H616_DX_DRI,
@@ -1231,6 +1357,7 @@ static const struct dram_para para = {
 	.odt_en = CONFIG_DRAM_SUN50I_H616_ODT_EN,
 	.tpr0 = CONFIG_DRAM_SUN50I_H616_TPR0,
 	.tpr2 = CONFIG_DRAM_SUN50I_H616_TPR2,
+	.tpr6 = CONFIG_DRAM_SUN50I_H616_TPR6,
 	.tpr10 = CONFIG_DRAM_SUN50I_H616_TPR10,
 	.tpr11 = CONFIG_DRAM_SUN50I_H616_TPR11,
 	.tpr12 = CONFIG_DRAM_SUN50I_H616_TPR12,
(quoted diff) +0 -0

b/arch/arm/mach-sunxi/dram_timings/Makefile index 8bfd99448a..5f20341924 100644

arch/arm/mach-sunxi/dram_timings/Makefile +1 -0
@@ -5,3 +5,4 @@ obj-$(CONFIG_SUNXI_DRAM_H6_LPDDR3)	+= h6_lpddr3.o
 obj-$(CONFIG_SUNXI_DRAM_H6_DDR3_1333)	+= h6_ddr3_1333.o
 obj-$(CONFIG_SUNXI_DRAM_H616_DDR3_1333)	+= h616_ddr3_1333.o
 obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR3)	+= h616_lpddr3.o
+obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR4)	+= h616_lpddr4_2133.o
(quoted diff) +0 -0

b/arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file mode 100644 index 0000000000..c11cb8678f

arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +9 -0
@@ -0,0 +1,95 @@
+/*
+ * sun50i H616 LPDDR4-2133 timings, as programmed by Allwinner's boot0
+ * for orangepi zero3 with the H618 and LPDDR4 memory.
+ *
+ * (C) Copyright 2023 Mikhail Kalashnikov <[email protected]>
+ *   Based on H6 DDR3 timings:
+ *   (C) Copyright 2020 Jernej Skrabec <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+

arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c line 19

Quoted 10 lines
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +10 -0
+ */
+
+#include <common.h>
+#include <asm/arch/dram.h>
+#include <asm/arch/cpu.h>
+
+void mctl_set_timing_params(const struct dram_para *para)
+{
+	struct sunxi_mctl_ctl_reg * const mctl_ctl =
+			(struct sunxi_mctl_ctl_reg 

*)SUNXI_DRAM_CTL0_BASE;

arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c line 31

Quoted 12 lines
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +12 -0
+
+	u8 tccd		= 4;
+	u8 tfaw		= ns_to_t(40);
+	u8 trrd		= max(ns_to_t(10), 2);
+	u8 trcd		= max(ns_to_t(18), 2);
+	u8 trc		= ns_to_t(65);
+	u8 txp		= max(ns_to_t(8), 2);
+	u8 trtp		= max(ns_to_t(8), 4);
+	u8 trp		= ns_to_t(21);
+	u8 tras		= ns_to_t(42);
+	u16 trefi	= ns_to_t(3904) / 32;
+	u16 trfc	= ns_to_t(280);

My notes say 180 instead of 280. Did you check if register value matches if booted with boot0?

Best regards,
Jernej

Quoted 64 lines
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +64 -0
+	u16 txsr	= ns_to_t(190);
+
+	u8 tmrw		= max(ns_to_t(14), 5);
+	u8 tmrd		= tmrw;
+	u8 tmod		= 12;
+	u8 tcke		= max(ns_to_t(15), 2);
+	u8 tcksrx	= max(ns_to_t(2), 2);
+	u8 tcksre	= max(ns_to_t(5), 2);
+	u8 tckesr	= tcke;
+	u8 trasmax	= (trefi * 9) / 32;
+	u8 txs		= 4;
+	u8 txsdll	= 16;
+	u8 txsabort	= 4;
+	u8 txsfast	= 4;
+	u8 tcl		= 10;
+	u8 tcwl		= 5;
+	u8 t_rdata_en	= 17;
+	u8 tphy_wrlat	= 5;
+
+	u8 twtp		= 24;
+	u8 twr2rd	= max(trrd, (u8)4) + 14;
+	u8 trd2wr	= (ns_to_t(4) + 17) - ns_to_t(1);
+
+	/* set DRAM timing */
+	writel((twtp << 24) | (tfaw << 16) | (trasmax << 8) | tras,
+	       &mctl_ctl->dramtmg[0]);
+	writel((txp << 16) | (trtp << 8) | trc, &mctl_ctl->dramtmg[1]);
+	writel((tcwl << 24) | (tcl << 16) | (trd2wr << 8) | twr2rd,
+	       &mctl_ctl->dramtmg[2]);
+	writel((tmrw << 20) | (tmrd << 12) | tmod, &mctl_ctl->dramtmg[3]);
+	writel((trcd << 24) | (tccd << 16) | (trrd << 8) | trp,
+	       &mctl_ctl->dramtmg[4]);
+	writel((tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | tcke,
+	       &mctl_ctl->dramtmg[5]);
+	/* Value suggested by ZynqMP manual and used by libdram */
+	writel((txp + 2) | 0x02020000, &mctl_ctl->dramtmg[6]);
+	writel((txsfast << 24) | (txsabort << 16) | (txsdll << 8) | txs,
+	       &mctl_ctl->dramtmg[8]);
+	writel(0x00020208, &mctl_ctl->dramtmg[9]);
+	writel(0xE0C05, &mctl_ctl->dramtmg[10]);
+	writel(0x440C021C, &mctl_ctl->dramtmg[11]);
+	writel(8, &mctl_ctl->dramtmg[12]);
+	writel(0xA100002, &mctl_ctl->dramtmg[13]);
+	writel(txsr, &mctl_ctl->dramtmg[14]);
+
+	clrsetbits_le32(&mctl_ctl->init[0], 0xC0000FFF, 0x3f0);
+	writel(0x01f20000, &mctl_ctl->init[1]);
+	writel(0x00000d05, &mctl_ctl->init[2]);
+	writel(0, &mctl_ctl->dfimisc);
+	writel(0x0034001b, &mctl_ctl->init[3]);
+	writel(0x00330000, &mctl_ctl->init[4]);
+	writel(0x00040072, &mctl_ctl->init[6]);
+	writel(0x00240009, &mctl_ctl->init[7]);
+
+	clrsetbits_le32(&mctl_ctl->rankctl, 0xff0, 0x660);
+
+	/* Configure DFI timing */
+	writel(tphy_wrlat | 0x2000000 | (t_rdata_en << 16) | 0x808000,
+	       &mctl_ctl->dfitmg0);
+	writel(0x100202, &mctl_ctl->dfitmg1);
+
+	/* set refresh timing */
+	writel((trefi << 16) | trfc, &mctl_ctl->rfshtmg);
+}
#0 lore raw

v3 cover sunxi: H616: add LPDDR4 support

From: iuncuim <[email protected]>

At the moment, the driver only supports DDR3 and LPDDR3 memory. Add support for a new type DRAM.
These changes have been successfully tested by me with orangepi zero3 4GB (DRAM: Rayson RS1G32LO4D2BDS-53BT).
This patch should be applied after this:
https://lore.kernel.org/all/[email protected]/

Changes from v2:
* added default value for TPR6 parameter
* added panic for unsupported DRAM types in switch/case conditions
* added new line at the end of the timings file, changed the description
* added a few small missing parts obtained from boot0
https://lore.kernel.org/u-boot/[email protected]/

Changes from v1:
* replaced the phy_init array with one compatible with opizero3
* added DRAM TPR6 parameter
* adaptation to new mctl_phy_configure_odt()
* added timings for the board orangepi zero3 4GB
https://lore.kernel.org/u-boot/[email protected]/

iuncuim (1):
sunxi: H616: add LPDDR4 DRAM support

 .../include/asm/arch-sunxi/dram_sun50i_h616.h |   2 +
 arch/arm/mach-sunxi/Kconfig                   |  17 ++
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 197 ++++++++++++++----
 arch/arm/mach-sunxi/dram_timings/Makefile     |   1 +
 .../dram_timings/h616_lpddr4_2133.c           |  95 +++++++++
 5 files changed, 277 insertions(+), 35 deletions(-)
 create mode 100644 arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c
Signature · 1 line
2.42.0
#1 lore raw

PATCH v3 1/1 sunxi: H616: add LPDDR4 DRAM support

From: iuncuim <[email protected]>

The H616 SoC family has support for several types of DRAM: DDR3, LPDDR3, DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 and LPDDR3 memory. Let's extend the driver to support the LPDDR4 memory. This type of memory widely used in device with T507(-H) SoC and new orangepi zero3 with H618.
The compatibility with T507 is not yet complete, because there is difference in the phy_init array.
The LPDDR4-2133 timings correspond to DRAM Rayson RS1G32LO4D2BDS-53BT found on the NOR SPI from the Orangepi Zero 3 4GB.

---
 .../include/asm/arch-sunxi/dram_sun50i_h616.h |   2 +
 arch/arm/mach-sunxi/Kconfig                   |  17 ++
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 197 ++++++++++++++----
 arch/arm/mach-sunxi/dram_timings/Makefile     |   1 +
 .../dram_timings/h616_lpddr4_2133.c           |  95 +++++++++
 5 files changed, 277 insertions(+), 35 deletions(-)
 create mode 100644 arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c
arch/arm/include/asm/arch-sunxi/dram_sun50i_h616.h +2 -0
index 11774deded..a8fdda124a 100644
@@ -130,6 +130,7 @@ check_member(sunxi_mctl_ctl_reg, unk_0x4240, 0x4240);
 #define MSTR_DEVICETYPE_LPDDR2	BIT(2)
 #define MSTR_DEVICETYPE_LPDDR3	BIT(3)
 #define MSTR_DEVICETYPE_DDR4	BIT(4)
+#define MSTR_DEVICETYPE_LPDDR4	BIT(5)
 #define MSTR_DEVICETYPE_MASK	GENMASK(5, 0)
 #define MSTR_2TMODE		BIT(10)
 #define MSTR_BUSWIDTH_FULL	(0 << 12)
@@ -154,6 +155,7 @@ struct dram_para {
 	u32 odt_en;
 	u32 tpr0;
 	u32 tpr2;
+	u32 tpr6;
 	u32 tpr10;
 	u32 tpr11;
 	u32 tpr12;
arch/arm/mach-sunxi/Kconfig +17 -0
index 9d5df2c102..e65bcb36a2 100644
@@ -85,6 +85,12 @@ config DRAM_SUN50I_H616_TPR2
 	help
 	  TPR2 value from vendor DRAM settings.
 
+config DRAM_SUN50I_H616_TPR6
+	hex "H616 DRAM TPR6 parameter"
+	default 0x3300c080
+	help
+	  TPR6 value from vendor DRAM settings.
+
 config DRAM_SUN50I_H616_TPR10
 	hex "H616 DRAM TPR10 parameter"
 	help
@@ -441,6 +447,9 @@ config SUNXI_DRAM_DDR2
 config SUNXI_DRAM_LPDDR3
 	bool
 
+config SUNXI_DRAM_LPDDR4
+	bool
+
 choice
 	prompt "DRAM Type and Timing"
 	default SUNXI_DRAM_DDR3_1333 if !MACH_SUN8I_V3S
@@ -484,6 +493,14 @@ config SUNXI_DRAM_H616_LPDDR3
 	  This option is the LPDDR3 timing used by the stock boot0 by
 	  Allwinner.
 
+config SUNXI_DRAM_H616_LPDDR4
+	bool "LPDDR4 DRAM chips on the H616 DRAM controller"
+	select SUNXI_DRAM_LPDDR4
+	depends on DRAM_SUN50I_H616
+	help
+	  This option is the LPDDR4 timing used by the stock boot0 by
+	  Allwinner.
+
 config SUNXI_DRAM_H616_DDR3_1333
 	bool "DDR3-1333 boot0 timings on the H616 DRAM controller"
 	select SUNXI_DRAM_DDR3
arch/arm/mach-sunxi/dram_sun50i_h616.c +162 -35

328 lines not on this page · raw message

arch/arm/mach-sunxi/dram_timings/Makefile +1 -0
index 8bfd99448a..5f20341924 100644
@@ -5,3 +5,4 @@ obj-$(CONFIG_SUNXI_DRAM_H6_LPDDR3)	+= h6_lpddr3.o
 obj-$(CONFIG_SUNXI_DRAM_H6_DDR3_1333)	+= h6_ddr3_1333.o
 obj-$(CONFIG_SUNXI_DRAM_H616_DDR3_1333)	+= h616_ddr3_1333.o
 obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR3)	+= h616_lpddr3.o
+obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR4)	+= h616_lpddr4_2133.o
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +95 -0

95 lines not on this page · raw message

Signature · 1 line
2.42.0
maintainer
#4 lore raw

Re: [PATCH v3 1/1] sunxi: H616: add LPDDR4 DRAM support

In reply to Mikhail Kalashnikov

Dne sobota, 11. november 2023 ob 08:43:22 CET je Mikhail Kalashnikov napisal(a):

Quoted 59 lines

Hi Jernej,

Quoted 9 lines · Jernej Škrabec

Hi Mikhail,

I have some notes on LPDDR4 from a long time ago. It mostly matches to your code, but please take a look at comments below.

Note that I have extra code, not included in this patch, for mctl_phy_read_training(). At the very beginning, before any other register access is done, this should be added:

Quoted 6 lines
if (para->type == SUNXI_DRAM_TYPE_LPDDR4) {
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x800);
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x81c);
}

Maybe that will help with other LPDDR4 boards?

Current H618 and t507 boards do not yet require this feature. Yes, this feature may be required for future devices. I will add it in the next version.

Quoted 11 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_configure_odt(const struct · line 257

Quoted 8 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -0
@@ -246,8 +251,13 @@ static void mctl_phy_configure_odt(const struct
 dram_para *para) {
  	uint32_t val_lo, val_hi;
 
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x390, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x3d0, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x410, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x450, BIT(5), BIT(4));

I don't have above block. Something from newer libdram? Is it applicable to all DRAM types?

This function is present in the RE code for all types of memory. Binary file dumped from orangepi zero3 nor spi.I paid attention to this area code when comparing the sunxi u-boot dump (md.l) with the resulting mainline u-boot. Now I checked my tvbox with H616 and LPDDR3 and it doesn't have this block. In this case, maybe it would be better to make it only for devices with LPDDR4?

Quoted 6 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_phy_init(const struct dram_para *para, · line 1053

Quoted 4 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -0
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		writel(0x0, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);

I don't have above block. Maybe difference from newer version of libdram code?

This block was present in the sunxi t507 binaries for which the driver was originally intended. Now I checked original dump from orangepi zero3 NOR SPI. This is also present here.

Quoted 5 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_ctrl_init(const struct dram_para *para, · line 1209

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +0 -0
  	writel(reg_val, &mctl_ctl->odtcfg);
  	writel(reg_val, &mctl_ctl->unk_0x2240);
  	writel(reg_val, &mctl_ctl->unk_0x3240);

I have extra "writel(BIT(31), &mctl_com->cr);" after this block for all DRAM types. Not sure if it changes anything.

Looks like this has already been done in previous patches.

Quoted 8 lines
Quoted 3 lines

arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c line 31

Quoted 1 line
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +1 -0
+	u16 trfc	= ns_to_t(280);

My notes say 180 instead of 280. Did you check if register value matches if booted with boot0

I booted from NOR SPI of the sunxi u-boot and made a dump with md.l 0x047fb064. It show me value 0030006f, where 0x6f trfc value. Based on the transformation function - 111*1000/(792/2)=280,30(30) So, obtained value looks correct. Best regards,
Mikhail

Ok, thanks for double checking. I think next version can be merged and then issues can be fixed if they appear.

Best regards,
Jernej

#3 lore raw

Re: [PATCH v3 1/1] sunxi: H616: add LPDDR4 DRAM support

In reply to Jernej Škrabec

Hi Jernej,

Quoted 9 lines · Jernej Škrabec

Hi Mikhail,

I have some notes on LPDDR4 from a long time ago. It mostly matches to your code, but please take a look at comments below.

Note that I have extra code, not included in this patch, for mctl_phy_read_training(). At the very beginning, before any other register access is done, this should be added:

Quoted 6 lines
if (para->type == SUNXI_DRAM_TYPE_LPDDR4) {
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x800);
	writel(0, SUNXI_DRAM_PHY0_BASE + 0x81c);
}

Maybe that will help with other LPDDR4 boards?

Current H618 and t507 boards do not yet require this feature. Yes, this feature may be required for future devices. I will add it in the next version.

Quoted 11 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static void mctl_phy_configure_odt(const struct · line 257

Quoted 8 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -0
@@ -246,8 +251,13 @@ static void mctl_phy_configure_odt(const struct
 dram_para *para) {
  	uint32_t val_lo, val_hi;
 
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x390, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x3d0, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x410, BIT(5), BIT(4));
+	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x450, BIT(5), BIT(4));

I don't have above block. Something from newer libdram? Is it applicable to all DRAM types?

This function is present in the RE code for all types of memory. Binary file dumped from orangepi zero3 nor spi.I paid attention to this area code when comparing the sunxi u-boot dump (md.l) with the resulting mainline u-boot. Now I checked my tvbox with H616 and LPDDR3 and it doesn't have this block. In this case, maybe it would be better to make it only for devices with LPDDR4?

Quoted 5 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_phy_init(const struct dram_para *para, · line 1053

Quoted 4 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -0
+	case SUNXI_DRAM_TYPE_LPDDR4:
+		writel(0x0, &mctl_ctl->mrctrl1);
+		writel(0x80000030, &mctl_ctl->mrctrl0);
+		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);

I don't have above block. Maybe difference from newer version of libdram code?

This block was present in the sunxi t507 binaries for which the driver was originally intended. Now I checked original dump from orangepi zero3 NOR SPI. This is also present here.

Quoted 5 lines

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_ctrl_init(const struct dram_para *para, · line 1209

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +0 -0
  	writel(reg_val, &mctl_ctl->odtcfg);
  	writel(reg_val, &mctl_ctl->unk_0x2240);
  	writel(reg_val, &mctl_ctl->unk_0x3240);

I have extra "writel(BIT(31), &mctl_com->cr);" after this block for all DRAM types. Not sure if it changes anything.

Looks like this has already been done in previous patches.

Quoted 3 lines

arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c line 31

Quoted 1 line
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c new file +1 -0
+	u16 trfc	= ns_to_t(280);

My notes say 180 instead of 280. Did you check if register value matches if booted with boot0

I booted from NOR SPI of the sunxi u-boot and made a dump with md.l 0x047fb064. It show me value 0030006f, where 0x6f trfc value. Based on the transformation function - 111*1000/(792/2)=280,30(30) So, obtained value looks correct. Best regards, Mikhail