dt-bindings: omap: Add Motorola mapphone mz609 and mz617 tablets

@@ -134,6 +134,8 @@ properties:
               - amazon,omap4-kc1        # Amazon Kindle Fire (first generation)
               - motorola,droid4         # Motorola Droid 4 XT894
               - motorola,droid-bionic   # Motorola Droid Bionic XT875
+              - motorola,xyboard-mz609
+              - motorola,xyboard-mz617
               - ti,omap4-panda
               - ti,omap4-sdp
           - const: ti,omap4430

@@ -6,15 +6,6 @@
 #include "motorola-cpcap-mapphone.dtsi"
 
 / {
-	chosen {
-		stdout-path = &uart3;
-	};
-
-	aliases {
-		display0 = &lcd0;
-		display1 = &hdmi0;
-	};
-
 	/*
 	 * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
 	 * then 1023 - 1024 seems to contain mbm.

@@ -92,17 +83,6 @@ hsusb2_phy: usb-phy@2 {
 		#phy-cells = <0>;
 	};
 
-	/* LCD regulator from sw5 source */
-	lcd_regulator: regulator-lcd {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd";
-		regulator-min-microvolt = <5050000>;
-		regulator-max-microvolt = <5050000>;
-		gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;	/* gpio96 */
-		enable-active-high;
-		vin-supply = <&sw5>;
-	};
-
 	/* This is probably coming straight from the battery.. */
 	wl12xx_vmmc: regulator-wl12xx {
 		compatible = "regulator-fixed";

@@ -160,14 +140,6 @@ vibrator {
 		pwm-names = "enable", "direction";
 		direction-duty-cycle-ns = <10000000>;
 	};
-
-	backlight: backlight {
-		compatible = "led-backlight";
-
-		leds = <&backlight_led>;
-		brightness-levels = <31 63 95 127 159 191 223 255>;
-		default-brightness-level = <6>;
-	};
 };
 
 &cpu_thermal {

@@ -197,57 +169,6 @@ &dss {
 	status = "okay";
 };
 
-&dsi1 {
-	status = "okay";
-	vdd-supply = <&vcsi>;
-
-	port {
-		dsi1_out_ep: endpoint {
-			remote-endpoint = <&lcd0_in>;
-			lanes = <0 1 2 3 4 5>;
-		};
-	};
-
-	lcd0: panel@0 {
-		compatible = "motorola,droid4-panel", "panel-dsi-cm";
-		reg = <0>;
-		label = "lcd0";
-		vddi-supply = <&lcd_regulator>;
-		reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;	/* gpio101 */
-
-		backlight = <&backlight>;
-
-		width-mm = <50>;
-		height-mm = <89>;
-		rotation = <90>;
-
-		panel-timing {
-			clock-frequency = <0>;		/* Calculated by dsi */
-
-			hback-porch = <2>;
-			hactive = <540>;
-			hfront-porch = <0>;
-			hsync-len = <2>;
-
-			vback-porch = <1>;
-			vactive = <960>;
-			vfront-porch = <0>;
-			vsync-len = <1>;
-
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-
-		port {
-			lcd0_in: endpoint {
-				remote-endpoint = <&dsi1_out_ep>;
-			};
-		};
-	};
-};
-
 &hdmi {
 	status = "okay";
 	pinctrl-0 = <&dss_hdmi_pins>;

75 lines not on this page · raw message

@@ -1,11 +1,20 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /dts-v1/;
 
-#include "motorola-mapphone-common.dtsi"
+#include "motorola-mapphone-xt8xx.dtsi"
 
 / {
 	model = "Motorola Droid Bionic XT875";
 	compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display0 = &lcd0;
+		display1 = &hdmi0;
+	};
 };
 
 &keypad {

@@ -1,9 +1,21 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /dts-v1/;
 
-#include "motorola-mapphone-common.dtsi"
+#include "motorola-mapphone-xt8xx.dtsi"
 
 / {
+	model = "Motorola Droid 4 XT894";
+	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display0 = &lcd0;
+		display1 = &hdmi0;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 

@@ -33,11 +45,6 @@ slider {
 	};
 };
 
-/ {
-	model = "Motorola Droid 4 XT894";
-	compatible = "motorola,droid4", "ti,omap4430", "ti,omap4";
-};
-
 &keypad {
 	keypad,num-rows = <8>;
 	keypad,num-columns = <8>;

@@ -54,35 +54,6 @@ hdmi_regulator: regulator-hdmi {
 		regulator-always-on;
 	};
 
-	/* FS USB Host PHY on port 1 for mdm6600 */
-	fsusb1_phy: usb-phy@1 {
-		compatible = "motorola,mapphone-mdm6600";
-		pinctrl-0 = <&usb_mdm6600_pins>;
-		pinctrl-1 = <&usb_mdm6600_sleep_pins>;
-		pinctrl-names = "default", "sleep";
-		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
-		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
-		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
-		/* mode: gpio_148 gpio_149 */
-		motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
-				      <&gpio5 21 GPIO_ACTIVE_HIGH>;
-		/* cmd: gpio_103 gpio_104 gpio_142 */
-		motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
-				     <&gpio4 8 GPIO_ACTIVE_HIGH>,
-				     <&gpio5 14 GPIO_ACTIVE_HIGH>;
-		/* status: gpio_52 gpio_53 gpio_55 */
-		motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
-					<&gpio2 21 GPIO_ACTIVE_HIGH>,
-					<&gpio2 23 GPIO_ACTIVE_HIGH>;
-		#phy-cells = <0>;
-	};
-
-	/* HS USB host TLL nop-phy on port 2 for w3glte */
-	hsusb2_phy: usb-phy@2 {
-		compatible = "usb-nop-xceiv";
-		#phy-cells = <0>;
-	};
-
 	/* This is probably coming straight from the battery.. */
 	wl12xx_vmmc: regulator-wl12xx {
 		compatible = "regulator-fixed";

@@ -113,33 +84,6 @@ soundcard {
 
 		dais = <&mcbsp2_port>, <&mcbsp3_port>;
 	};
-
-	pwm8: pwm-8 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_direction_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer8>;
-		ti,clock-source = <0x01>;
-	};
-
-	pwm9: pwm-9 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&vibrator_enable_pin>;
-
-		compatible = "ti,omap-dmtimer-pwm";
-		#pwm-cells = <3>;
-		ti,timers = <&timer9>;
-		ti,clock-source = <0x01>;
-	};
-
-	vibrator {
-		compatible = "pwm-vibrator";
-		pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
-		pwm-names = "enable", "direction";
-		direction-duty-cycle-ns = <10000000>;
-	};
 };
 
 &cpu_thermal {

@@ -183,13 +127,6 @@ hdmi_out: endpoint {
 	};
 };
 
-/* Battery NVRAM on 1-wire handled by w1_ds250x driver */
-&hdqw1w {
-	pinctrl-0 = <&hdq_pins>;
-	pinctrl-names = "default";
-	ti,mode = "1w";
-};
-
 &i2c1 {
 	tmp105@48 {
 		compatible = "ti,tmp105";

@@ -243,34 +180,6 @@ wlcore: wlcore@2 {
 	};
 };
 
-&i2c2 {
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&touchscreen_pins>;
-
-		reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */
-
-		/* gpio_183 with sys_nirq2 pad as wakeup */
-		interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
-				      <&omap4_pmx_core 0x160>;
-		interrupt-names = "irq", "wakeup";
-		wakeup-source;
-	};
-
-	isl29030@44 {
-		compatible = "isil,isl29030";
-		reg = <0x44>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&als_proximity_pins>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
-	};
-};
-
 &omap4_pmx_core {
 
 	/* hdmi_hpd.gpio_63 */

@@ -280,13 +189,6 @@ OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
 		>;
 	};
 
-	hdq_pins: hdq-pins {
-		pinctrl-single,pins = <
-		/* 0x4a100120 hdq_sio.hdq_sio aa27 */
-		OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
-		>;
-	};
-
 	/* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
 	dss_hdmi_pins: dss-hdmi-pins {
 		pinctrl-single,pins = <

@@ -348,73 +250,6 @@ OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
 		>;
 	};
 
-	touchscreen_pins: touchscreen-pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	als_proximity_pins: als-proximity-pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
-		>;
-	};
-
-	usb_mdm6600_pins: usb-mdm6600-pins {
-		pinctrl-single,pins = <
-		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
-		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
-
-		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
-		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
-
-		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
-		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
-		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
-
-		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
-		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
-
-		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
-		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
-
-		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
-		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
-
-		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
-		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
-
-		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
-		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
-		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
-
-		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
-		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
-	/* Modem sleep pins to keep gpio_49 high with internal pull */
-	usb_mdm6600_sleep_pins: usb-mdm6600-sleep-pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x072, PIN_INPUT_PULLUP | MUX_MODE7) /* Keep gpio_49 reset high */
-		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
-		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
-		>;
-	};
-
 	usb_ulpi_pins: usb-ulpi-pins {
 		pinctrl-single,pins = <
 		OMAP4_IOPAD(0x196, MUX_MODE7)

@@ -522,18 +357,6 @@ OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_clkx */
 		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
 		>;
 	};
-
-	vibrator_direction_pin: vibrator-direction-pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)	/* dmtimer8_pwm_evt (gpio_27) */
-		>;
-	};
-
-	vibrator_enable_pin: vibrator-enable-pins {
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)	/* dmtimer9_pwm_evt (gpio_28) */
-		>;
-	};
 };
 
 &omap4_pmx_wkup {

@@ -550,17 +373,6 @@ &rng_target {
 	status = "disabled";
 };
 
-/* Configure pwm clock source for timers 8 & 9 */
-&timer8 {
-	assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_32k_ck>;
-};
-
-&timer9 {
-	assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
-	assigned-clock-parents = <&sys_32k_ck>;
-};
-
 /*
  * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
  * for wake-up events for both the USB PHY and the UART. We can use gpio_149

@@ -593,20 +405,6 @@ bluetooth {
 	};
 };
 
-&usbhsohci {
-	phys = <&fsusb1_phy>;
-	phy-names = "usb";
-};
-
-&usbhsehci {
-	phys = <&hsusb2_phy>;
-};
-
-&usbhshost {
-	port1-mode = "ohci-phy-4pin-dpdm";
-	port2-mode = "ehci-tll";
-};
-
 /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
 &usb_otg_hs {
 	interface-type = <1>;

@@ -619,23 +417,6 @@ &usb_otg_hs {
 	power = <150>;
 };
 
-&i2c4 {
-	ak8975: magnetometer@c {
-		compatible = "asahi-kasei,ak8975";
-		reg = <0x0c>;
-
-		vdd-supply = <&vhvio>;
-
-		interrupt-parent = <&gpio6>;
-		interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
-
-		rotation-matrix = "-1", "0", "0",
-				  "0", "1", "0",
-				  "0", "0", "-1";
-
-	};
-};
-
 &mcbsp2 {
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";

234 lines not on this page · raw message

@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /dts-v1/;
 
-#include "motorola-mapphone-common.dtsi"
+#include "motorola-mapphone-handset.dtsi"
 
 / {
 	backlight: backlight {

@@ -79,7 +79,9 @@ dtb-$(CONFIG_ARCH_OMAP4) += \
 	omap4-sdp.dtb \
 	omap4-sdp-es23plus.dtb \
 	omap4-var-dvk-om44.dtb \
-	omap4-var-stk-om44.dtb
+	omap4-var-stk-om44.dtb \
+	omap4-xyboard-mz609.dtb \
+	omap4-xyboard-mz617.dtb
 dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-baltos-ir2110.dtb \
 	am335x-baltos-ir3220.dtb \

new file mode 100644
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-common.dtsi"
+
+&keypad {
+	keypad,num-rows = <8>;
+	keypad,num-columns = <8>;
+	linux,keymap = <MATRIX_KEY(5, 0, KEY_VOLUMEUP)>,
+		       <MATRIX_KEY(3, 0, KEY_VOLUMEDOWN)>;
+};
+
+/*
+ * On tablets, mmc1 regulator is vsimcard instead of vwlan2 in the stock kernel
+ * dtb. The regulator may not be wired even if a MMC cage is added though.
+ */
+&mmc1 {
+	vmmc-supply = <&vsimcard>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;	/* gpio_176 */
+};

46 lines not on this page · raw message

new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "motorola-mapphone-mz607-mz617.dtsi"
+
+/ {
+	model = "Motorola Xyboard MZ617";
+	compatible = "motorola,xyboard-mz617", "ti,omap4430", "ti,omap4";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		display1 = &hdmi0;
+	};
+};