Skip to contentSkip to conversation

spi: pxa2xx: Update documentation

PATCH Superseded Andy Shevchenko 2 participants 6 messages Dec 7, 2023 – Dec 9, 2023 SPI

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover spi: pxa2xx: Update documentation

A couple of documentation updates.

Andy Shevchenko (2):
spi: pxa2xx: Use inclusive language
spi: pxa2xx: Update DMA mapping and using logic in the documentation

 Documentation/spi/pxa2xx.rst | 59 +++++++++++++++++-------------------
 1 file changed, 28 insertions(+), 31 deletions(-)
Signature · 1 line
2.43.0.rc1.1.gbec44491f096
#1 lore raw

PATCH 1/2 spi: pxa2xx: Use inclusive language

Replace master/slave by host/peripheral language in the documentation.

---
 Documentation/spi/pxa2xx.rst | 48 ++++++++++++++++++------------------
 1 file changed, 24 insertions(+), 24 deletions(-)
Documentation/spi/pxa2xx.rst +24 -24
index 04f2a3856c40..b66702724ccf 100644
@@ -3,13 +3,13 @@ PXA2xx SPI on SSP driver HOWTO
 ==============================
 
 This a mini HOWTO on the pxa2xx_spi driver. The driver turns a PXA2xx
-synchronous serial port into an SPI master controller
+synchronous serial port into an SPI host controller
 (see Documentation/spi/spi-summary.rst). The driver has the following features
 
 - Support for any PXA2xx and compatible SSP.
 - SSP PIO and SSP DMA data transfers.
 - External and Internal (SSPFRM) chip selects.
-- Per slave device (chip) configuration.
+- Per peripheral device (chip) configuration.
 - Full suspend, freeze, resume support.
 
 The driver is built around a &struct spi_message FIFO serviced by kernel
@@ -17,10 +17,10 @@ thread. The kernel thread, spi_pump_messages(), drives message FIFO and
 is responsible for queuing SPI transactions and setting up and launching
 the DMA or interrupt driven transfers.
 
-Declaring PXA2xx Master Controllers
------------------------------------
-Typically, for a legacy platform, an SPI master is defined in the
-arch/.../mach-*/board-*.c as a "platform device". The master configuration
+Declaring PXA2xx host controllers
+---------------------------------
+Typically, for a legacy platform, an SPI host is defined in the
+arch/.../mach-*/board-*.c as a "platform device". The host configuration
 is passed to the driver via a table found in include/linux/spi/pxa2xx_spi.h::
 
   struct pxa2xx_spi_controller {
@@ -30,7 +30,7 @@ is passed to the driver via a table found in include/linux/spi/pxa2xx_spi.h::
   };
 
 The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
-slave device (chips) attached to this SPI master.
+peripheral devices (chips) attached to this SPI host controller.
 
 The "pxa2xx_spi_controller.enable_dma" field informs the driver that SSP DMA should
 be used. This caused the driver to acquire two DMA channels: Rx channel and
@@ -40,8 +40,8 @@ See the "PXA2xx Developer Manual" section "DMA Controller".
 For the new platforms the description of the controller and peripheral devices
 comes from Device Tree or ACPI.
 
-NSSP MASTER SAMPLE
-------------------
+NSSP HOST SAMPLE
+----------------
 Below is a sample configuration using the PXA255 NSSP for a legacy platform::
 
   static struct resource pxa_spi_nssp_resources[] = {
@@ -57,7 +57,7 @@ Below is a sample configuration using the PXA255 NSSP for a legacy platform::
 	},
   };
 
-  static struct pxa2xx_spi_controller pxa_nssp_master_info = {
+  static struct pxa2xx_spi_controller pxa_nssp_ctrl_info = {
 	.num_chipselect = 1, /* Matches the number of chips attached to NSSP */
 	.enable_dma = 1, /* Enables NSSP DMA */
   };
@@ -68,7 +68,7 @@ Below is a sample configuration using the PXA255 NSSP for a legacy platform::
 	.resource = pxa_spi_nssp_resources,
 	.num_resources = ARRAY_SIZE(pxa_spi_nssp_resources),
 	.dev = {
-		.platform_data = &pxa_nssp_master_info, /* Passed to driver */
+		.platform_data = &pxa_nssp_ctrl_info, /* Passed to driver */
 	},
   };
 
@@ -81,17 +81,17 @@ Below is a sample configuration using the PXA255 NSSP for a legacy platform::
 	(void)platform_add_device(devices, ARRAY_SIZE(devices));
   }
 
-Declaring Slave Devices
------------------------
-Typically, for a legacy platform, each SPI slave (chip) is defined in the
+Declaring peripheral devices
+----------------------------
+Typically, for a legacy platform, each SPI peripheral device (chip) is defined in the
 arch/.../mach-*/board-*.c using the "spi_board_info" structure found in
 "linux/spi/spi.h". See "Documentation/spi/spi-summary.rst" for additional
 information.
 
-Each slave device attached to the PXA must provide slave specific configuration
+Each peripheral device (chip) attached to the PXA must provide specific chip configuration
 information via the structure "pxa2xx_spi_chip" found in
-"include/linux/spi/pxa2xx_spi.h".  The pxa2xx_spi master controller driver
-will uses the configuration whenever the driver communicates with the slave
+"include/linux/spi/pxa2xx_spi.h". The pxa2xx_spi host controller driver
+will uses the configuration whenever the driver communicates with the peripheral
 device. All fields are optional.
 
 ::
@@ -123,7 +123,7 @@ dma_burst_size == 0.
 The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
 trailing bytes in the SSP receiver FIFO. The correct value for this field is
 dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
-slave device.  Please note that the PXA2xx SSP 1 does not support trailing byte
+peripheral device. Please note that the PXA2xx SSP 1 does not support trailing byte
 timeouts and must busy-wait any trailing bytes.
 
 NOTE: the SPI driver cannot control the chip select if SSPFRM is used, so the
@@ -132,8 +132,8 @@ asserted around the complete message. Use SSPFRM as a GPIO (through a descriptor
 to accommodate these chips.
 
 
-NSSP SLAVE SAMPLE
------------------
+NSSP PERIPHERAL SAMPLE
+----------------------
 For a legacy platform or in some other cases, the pxa2xx_spi_chip structure
 is passed to the pxa2xx_spi driver in the "spi_board_info.controller_data"
 field. Below is a sample configuration using the PXA255 NSSP.
@@ -161,16 +161,16 @@ field. Below is a sample configuration using the PXA255 NSSP.
 		.bus_num = 2, /* Framework bus number */
 		.chip_select = 0, /* Framework chip select */
 		.platform_data = NULL; /* No spi_driver specific config */
-		.controller_data = &cs8415a_chip_info, /* Master chip config */
-		.irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
+		.controller_data = &cs8415a_chip_info, /* Host controller config */
+		.irq = STREETRACER_APCI_IRQ, /* Peripheral device interrupt */
 	},
 	{
 		.modalias = "cs8405a", /* Name of spi_driver for this device */
 		.max_speed_hz = 3686400, /* Run SSP as fast a possible */
 		.bus_num = 2, /* Framework bus number */
 		.chip_select = 1, /* Framework chip select */
-		.controller_data = &cs8405a_chip_info, /* Master chip config */
-		.irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
+		.controller_data = &cs8405a_chip_info, /* Host controller config */
+		.irq = STREETRACER_APCI_IRQ, /* Peripheral device interrupt */
 	},
   };
 
Signature · 1 line
2.43.0.rc1.1.gbec44491f096
#2 lore raw

PATCH 2/2 spi: pxa2xx: Update DMA mapping and using logic in the documentation

In reply to Andy Shevchenko

Update DMA mapping and using logic in the documentation to follow what the code does.

---
 Documentation/spi/pxa2xx.rst | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)
Documentation/spi/pxa2xx.rst +4 -7
index b66702724ccf..61c7b9dd833b 100644
@@ -193,17 +193,14 @@ mode supports both coherent and stream based DMA mappings.
 The following logic is used to determine the type of I/O to be used on
 a per "spi_transfer" basis::
 
-  if !enable_dma then
-	always use PIO transfers
+  if spi_message.len > 65536 then
+        if spi_message.is_dma_mapped or rx_dma_buf != 0 or tx_dma_buf != 0 then
+              reject premapped transfers
 
-  if spi_message.len > 8191 then
 	print "rate limited" warning
 	use PIO transfers
 
-  if spi_message.is_dma_mapped and rx_dma_buf != 0 and tx_dma_buf != 0 then
-	use coherent DMA mode
-
-  if rx_buf and tx_buf are aligned on 8 byte boundary then
+  if enable_dma and the size is in the range [DMA burst size..65536] then
 	use streaming DMA mode
 
   otherwise
Signature · 1 line
2.43.0.rc1.1.gbec44491f096
#3 lore raw

Re: [PATCH v1 2/2] spi: pxa2xx: Update DMA mapping and using logic in the documentation

Quoted 2 lines · Andy Shevchenko

Update DMA mapping and using logic in the documentation to follow what the code does.

...

Documentation/spi/pxa2xx.rst mode supports both coherent and stream based DMA mappings. · line 198

Quoted 5 lines
Documentation/spi/pxa2xx.rst +3 -2
-  if !enable_dma then
-	always use PIO transfers
+  if spi_message.len > 65536 then
+        if spi_message.is_dma_mapped or rx_dma_buf != 0 or tx_dma_buf != 0 then
+              reject premapped transfers

Here seems inconsistent indentation. I'll fix it in the next version. Mark, should I resend patch 1 as well?

Signature · 2 lines
With Best Regards,
Andy Shevchenko
maintainer
#4 lore raw

Re: [PATCH v1 2/2] spi: pxa2xx: Update DMA mapping and using logic in the documentation

Quoted 2 lines · Andy Shevchenko

Here seems inconsistent indentation. I'll fix it in the next version. Mark, should I resend patch 1 as well?

Yes, please.

maintainer
#5 lore raw
In reply to Andy Shevchenko
Quoted 10 lines · Andy Shevchenko

A couple of documentation updates.

Andy Shevchenko (2):
spi: pxa2xx: Use inclusive language
spi: pxa2xx: Update DMA mapping and using logic in the documentation

Documentation/spi/pxa2xx.rst | 59 +++++++++++++++++-------------------

 1 file changed, 28 insertions(+), 31 deletions(-)

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/2] spi: pxa2xx: Use inclusive language

      commit: c3aeaf2f0ec8af93189488bda3928a1ac7752388
[2/2] spi: pxa2xx: Update DMA mapping and using logic in the documentation
      commit: 8bc2a3634b87e2235535b5527f83ff529df68b56

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark