Skip to contentSkip to conversation

scsi: ufs: qcom: avoid re-init quirk when gears match

PATCH Applied Eric Chanudet 4 participants 5 messages Jan 23, 2024 – Jan 30, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 scsi: ufs: qcom: avoid re-init quirk when gears match

On sa8775p-ride, probing the hba will go through the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info are same during the second init.

The REINIT quirk only applies starting with controller v4. For these, ufs_qcom_get_hs_gear() reads the highest supported gear when setting the host_params. After the negotiation, if the host and device are on the same gear, it is the highest gear supported between the two. Skip REINIT to save some time.

---

v1 -> v2:
* drop test against host->hw_ver.major >= 4 and amend description as a
result (Andrew/Mani)
* add comment, test device gear against host->phy_gear and reset
host->phy_gear only if necessary (Mani)
* Link to v1: https://lore.kernel.org/linux-arm-msm/[email protected]/

trace_event=ufs:ufshcd_init reports the time spent in ufshcd_probe_hba
where the re-init quirk is performed:
Currently:
0.355879: ufshcd_init: 1d84000.ufs: took 103377 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0 With this patch:
0.297676: ufshcd_init: 1d84000.ufs: took 43553 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0

 drivers/ufs/host/ufs-qcom.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/ufs/host/ufs-qcom.c +11 -2
index 39eef470f8fa..f7dba7236c6e 100644
@@ -738,8 +738,17 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 		 * the second init can program the optimal PHY settings. This allows one to start
 		 * the first init with either the minimum or the maximum support gear.
 		 */
-		if (hba->ufshcd_state == UFSHCD_STATE_RESET)
-			host->phy_gear = dev_req_params->gear_tx;
+		if (hba->ufshcd_state == UFSHCD_STATE_RESET) {
+			/*
+			 * Skip REINIT if the negotiated gear matches with the
+			 * initial phy_gear. Otherwise, update the phy_gear to
+			 * program the optimal gear setting during REINIT.
+			 */
+			if (host->phy_gear == dev_req_params->gear_tx)
+				hba->quirks &= ~UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
+			else
+				host->phy_gear = dev_req_params->gear_tx;
+		}
 
 		/* enable the device ref clock before changing to HS mode */
 		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
Signature · 1 line
2.43.0
Reviewed-by on v2 1/1
#1 lore raw
Quoted 11 lines · Eric Chanudet

On sa8775p-ride, probing the hba will go through the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info are same during the second init.

The REINIT quirk only applies starting with controller v4. For these, ufs_qcom_get_hs_gear() reads the highest supported gear when setting the host_params. After the negotiation, if the host and device are on the same gear, it is the highest gear supported between the two. Skip REINIT to save some time.

- Mani

Quoted 46 lines

---

v1 -> v2:
* drop test against host->hw_ver.major >= 4 and amend description as a
result (Andrew/Mani)
* add comment, test device gear against host->phy_gear and reset
host->phy_gear only if necessary (Mani)
* Link to v1: https://lore.kernel.org/linux-arm-msm/[email protected]/

trace_event=ufs:ufshcd_init reports the time spent in ufshcd_probe_hba
where the re-init quirk is performed:
Currently:
0.355879: ufshcd_init: 1d84000.ufs: took 103377 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0 With this patch:
0.297676: ufshcd_init: 1d84000.ufs: took 43553 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0

 drivers/ufs/host/ufs-qcom.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/ufs/host/ufs-qcom.c +11 -2
index 39eef470f8fa..f7dba7236c6e 100644
@@ -738,8 +738,17 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 		 * the second init can program the optimal PHY settings. This allows one to start
 		 * the first init with either the minimum or the maximum support gear.
 		 */
-		if (hba->ufshcd_state == UFSHCD_STATE_RESET)
-			host->phy_gear = dev_req_params->gear_tx;
+		if (hba->ufshcd_state == UFSHCD_STATE_RESET) {
+			/*
+			 * Skip REINIT if the negotiated gear matches with the
+			 * initial phy_gear. Otherwise, update the phy_gear to
+			 * program the optimal gear setting during REINIT.
+			 */
+			if (host->phy_gear == dev_req_params->gear_tx)
+				hba->quirks &= ~UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
+			else
+				host->phy_gear = dev_req_params->gear_tx;
+		}
 
 		/* enable the device ref clock before changing to HS mode */
 		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
Signature · 1 line
2.43.0
Signature · 1 line
மணிவண்ணன் சதாசிவம்
Tested-by on v2 1/1
#2 lore raw
In reply to Eric Chanudet
Quoted 11 lines · Eric Chanudet

On sa8775p-ride, probing the hba will go through the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info are same during the second init.

The REINIT quirk only applies starting with controller v4. For these, ufs_qcom_get_hs_gear() reads the highest supported gear when setting the host_params. After the negotiation, if the host and device are on the same gear, it is the highest gear supported between the two. Skip REINIT to save some time.

On the sa8775p-ride I have I see similar results to what you mention! Thanks.

Quoted 47 lines

---

v1 -> v2:
* drop test against host->hw_ver.major >= 4 and amend description as a
result (Andrew/Mani)
* add comment, test device gear against host->phy_gear and reset
host->phy_gear only if necessary (Mani)
* Link to v1: https://lore.kernel.org/linux-arm-msm/[email protected]/

trace_event=ufs:ufshcd_init reports the time spent in ufshcd_probe_hba
where the re-init quirk is performed:
Currently:
0.355879: ufshcd_init: 1d84000.ufs: took 103377 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0 With this patch:
0.297676: ufshcd_init: 1d84000.ufs: took 43553 usecs, dev_state: UFS_ACTIVE_PWR_MODE, link_state: UIC_LINK_ACTIVE_STATE, err 0

 drivers/ufs/host/ufs-qcom.c | 13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/ufs/host/ufs-qcom.c +11 -2
index 39eef470f8fa..f7dba7236c6e 100644
@@ -738,8 +738,17 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 		 * the second init can program the optimal PHY settings. This allows one to start
 		 * the first init with either the minimum or the maximum support gear.
 		 */
-		if (hba->ufshcd_state == UFSHCD_STATE_RESET)
-			host->phy_gear = dev_req_params->gear_tx;
+		if (hba->ufshcd_state == UFSHCD_STATE_RESET) {
+			/*
+			 * Skip REINIT if the negotiated gear matches with the
+			 * initial phy_gear. Otherwise, update the phy_gear to
+			 * program the optimal gear setting during REINIT.
+			 */
+			if (host->phy_gear == dev_req_params->gear_tx)
+				hba->quirks &= ~UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
+			else
+				host->phy_gear = dev_req_params->gear_tx;
+		}
 
 		/* enable the device ref clock before changing to HS mode */
 		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
Signature · 1 line
2.43.0
#3 lore raw
In reply to Eric Chanudet

Eric,

Quoted 3 lines

On sa8775p-ride, probing the hba will go through the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info are same during the second init.

Applied to 6.9/scsi-staging, thanks!

Signature · 1 line
Martin K. Petersen	Oracle Linux Engineering
#4 lore raw
In reply to Eric Chanudet
Quoted 11 lines · Eric Chanudet

On sa8775p-ride, probing the hba will go through the UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH path although the power info are same during the second init.

The REINIT quirk only applies starting with controller v4. For these, ufs_qcom_get_hs_gear() reads the highest supported gear when setting the host_params. After the negotiation, if the host and device are on the same gear, it is the highest gear supported between the two. Skip REINIT to save some time.

[...]

Applied to 6.9/scsi-queue, thanks!

[1/1] scsi: ufs: qcom: avoid re-init quirk when gears match

      https://git.kernel.org/mkp/scsi/c/10a39667a117
Signature · 1 line
Martin K. Petersen	Oracle Linux Engineering