Skip to contentSkip to conversation

arm64: sun50i-h616: Add DMA and SPDIF controllers

PATCH Applied Chen-Yu Tsai 6 participants 15 messages Jan 27, 2024 – Jan 30, 2024

Subsystems (5)
lore
Share & tools
lore

Chen-Yu Tsai

author maintainer
#0 lore raw

v2 cover arm64: sun50i-h616: Add DMA and SPDIF controllers

From: Chen-Yu Tsai <[email protected]>

Hi everyone,

This is v2 of my H616/H618 DMA and SPDIF controller series.

Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

This series adds DMA and SPDIF controllers for the H616 and H618. There's also a fix for SPDIF on H6: the controller also has a receiver that was not correctly modeled.

Patch 1 fixes the binding for the SPDIF controller on the H6 by adding the RX DMA channel.

Patch 2 adds a compatible string for the H616's SPDIF transmitter to the binding.

Patch 3 adds a compatible string for the H616's SPDIF transmitter to the driver.

Patch 4 adds a compatible string for the H616's DMA controller.

Patch 5 adds the RX DMA channel to the SPDIF controller on the H6.

Patch 6 adds a device node for the H616's DMA controller.

Patch 7 adds a device node for the H616's SPDIF controller.

This was tested on the Orange Pi Zero 3 with SPI flash transfers and SPDIF audio output. The H6 SPDIF change is superficial as the driver does not support receiving / capturing an audio stream.

Please have a look. I expect the first three patches to go through the ASoC tree, the fourth patch to either go through the DMA tree, or through the sunxi tree with an Ack, and the last three through the sunxi tree.

Thanks
ChenYu

Chen-Yu Tsai (7):
dt-bindings: sound: sun4i-spdif: Fix requirements for H6
dt-bindings: sound: sun4i-spdif: Add Allwinner H616 compatible
ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616
arm64: dts: allwinner: h6: Add RX DMA channel for SPDIF
arm64: dts: allwinner: h616: Add DMA controller and DMA channels
arm64: dts: allwinner: h616: Add SPDIF device node

 .../dma/allwinner,sun50i-a64-dma.yaml         | 12 ++--
 .../sound/allwinner,sun4i-a10-spdif.yaml      |  5 +-
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   |  2 +
 .../boot/dts/allwinner/sun50i-h6-tanix.dtsi   |  2 +
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  7 +--
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 61 +++++++++++++++++++
 sound/soc/sunxi/sun4i-spdif.c                 |  5 ++
 7 files changed, 85 insertions(+), 9 deletions(-)
Signature · 1 line
2.39.2
author maintainer
#1 lore raw

PATCH v2 1/7 dt-bindings: sound: sun4i-spdif: Fix requirements for H6

From: Chen-Yu Tsai <[email protected]>

When the H6 was added to the bindings, only the TX DMA channel was added. As the hardware supports both transmit and receive functions, the binding is missing the RX DMA channel and is thus incorrect. Also, the reset control was not made mandatory.

Add the RX DMA channel for SPDIF on H6 by removing the compatible from the list of compatibles that should only have a TX DMA channel. And add the H6 compatible to the list of compatibles that require the reset control to be present.

Fixes b20453031472 ("dt-bindings: sound: sun4i-spdif: Add Allwinner H6 compatible")
---
 .../devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml    | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml +1 -1
index 8108c564dd78..98e2e053fa19 100644
@@ -62,6 +62,7 @@ allOf:
             enum:
               - allwinner,sun6i-a31-spdif
               - allwinner,sun8i-h3-spdif
+              - allwinner,sun50i-h6-spdif
 
     then:
       required:
@@ -73,7 +74,6 @@ allOf:
           contains:
             enum:
               - allwinner,sun8i-h3-spdif
-              - allwinner,sun50i-h6-spdif
 
     then:
       properties:
Signature · 1 line
2.39.2
author maintainer
#2 lore raw

PATCH v2 2/7 dt-bindings: sound: sun4i-spdif: Add Allwinner H616 compatible

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The SPDIF hardware block found in the H616 SoC has the same layout as the one found in the H6 SoC, except that it is missing the receiver side.

Add a new compatible string for it.

---
 .../devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml   | 3 +++
 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/sound/allwinner,sun4i-a10-spdif.yaml +3 -0
index 98e2e053fa19..aa32dc950e72 100644
@@ -22,6 +22,7 @@ properties:
       - const: allwinner,sun6i-a31-spdif
       - const: allwinner,sun8i-h3-spdif
       - const: allwinner,sun50i-h6-spdif
+      - const: allwinner,sun50i-h616-spdif
       - items:
           - const: allwinner,sun8i-a83t-spdif
           - const: allwinner,sun8i-h3-spdif
@@ -63,6 +64,7 @@ allOf:
               - allwinner,sun6i-a31-spdif
               - allwinner,sun8i-h3-spdif
               - allwinner,sun50i-h6-spdif
+              - allwinner,sun50i-h616-spdif
 
     then:
       required:
@@ -74,6 +76,7 @@ allOf:
           contains:
             enum:
               - allwinner,sun8i-h3-spdif
+              - allwinner,sun50i-h616-spdif
 
     then:
       properties:
Signature · 1 line
2.39.2
author maintainer
#3 lore raw

PATCH v2 3/7 ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The SPDIF hardware block found in the H616 SoC has the same layout as the one found in the H6 SoC, except that it is missing the receiver side.

Since the driver currently only supports the transmit function, support for the H616 is identical to what is currently done for the H6.

---
 sound/soc/sunxi/sun4i-spdif.c | 5 +++++
 1 file changed, 5 insertions(+)
sound/soc/sunxi/sun4i-spdif.c +5 -0
index 702386823d17..f41c30955857 100644
@@ -577,6 +577,11 @@ static const struct of_device_id sun4i_spdif_of_match[] = {
 		.compatible = "allwinner,sun50i-h6-spdif",
 		.data = &sun50i_h6_spdif_quirks,
 	},
+	{
+		.compatible = "allwinner,sun50i-h616-spdif",
+		/* Essentially the same as the H6, but without RX */
+		.data = &sun50i_h6_spdif_quirks,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, sun4i_spdif_of_match);
Signature · 1 line
2.39.2
author maintainer
#4 lore raw

PATCH v2 4/7 dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The DMA controllers found on the H616 and H618 are the same as the one found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Since the number of channels and endpoints are described with additional generic properties, just add a new H616-specific compatible string and fallback to the A100 one.

---
Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6

 .../bindings/dma/allwinner,sun50i-a64-dma.yaml       | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml +8 -4
index ec2d7a789ffe..0f2501f72cca 100644
@@ -28,6 +28,9 @@ properties:
       - items:
           - const: allwinner,sun8i-r40-dma
           - const: allwinner,sun50i-a64-dma
+      - items:
+          - const: allwinner,sun50i-h616-dma
+          - const: allwinner,sun50i-a100-dma
 
   reg:
     maxItems: 1
@@ -59,10 +62,11 @@ required:
 if:
   properties:
     compatible:
-      enum:
-        - allwinner,sun20i-d1-dma
-        - allwinner,sun50i-a100-dma
-        - allwinner,sun50i-h6-dma
+      contains:
+        enum:
+          - allwinner,sun20i-d1-dma
+          - allwinner,sun50i-a100-dma
+          - allwinner,sun50i-h6-dma
 
 then:
   properties:
Signature · 1 line
2.39.2
author maintainer
#7 lore raw

PATCH v2 5/7 arm64: dts: allwinner: h6: Add RX DMA channel for SPDIF

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The SPDIF hardware found on the H6 supports both transmit and receive functions. However it is missing the RX DMA channel.

Add the SPDIF hardware block's RX DMA channel. Also remove the by-default pinmux, since the end device can choose to implement either or both functionalities.

Fixes f95b598df419 ("arm64: dts: allwinner: Add SPDIF node for Allwinner H6")
---
 arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 2 ++
 arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi      | 2 ++
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi            | 7 +++----
 3 files changed, 7 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +2 -0
index 9ec49ac2f6fd..381d58cea092 100644
@@ -291,6 +291,8 @@ sw {
 };
 
 &spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 
arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi +2 -0
index 4903d6358112..855b7d43bc50 100644
@@ -166,6 +166,8 @@ &r_ir {
 };
 
 &spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +3 -4
index ca1d287a0a01..d11e5041bae9 100644
@@ -406,6 +406,7 @@ spi1_cs_pin: spi1-cs-pin {
 				function = "spi1";
 			};
 
+			/omit-if-no-ref/
 			spdif_tx_pin: spdif-tx-pin {
 				pins = "PH7";
 				function = "spdif";
@@ -655,10 +656,8 @@ spdif: spdif@5093000 {
 			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
 			clock-names = "apb", "spdif";
 			resets = <&ccu RST_BUS_SPDIF>;
-			dmas = <&dma 2>;
-			dma-names = "tx";
-			pinctrl-names = "default";
-			pinctrl-0 = <&spdif_tx_pin>;
+			dmas = <&dma 2>, <&dma 2>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
Signature · 1 line
2.39.2
author maintainer
#8 lore raw

PATCH v2 6/7 arm64: dts: allwinner: h616: Add DMA controller and DMA channels

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The DMA controllers found on the H616 and H618 are the same as the one found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Add a device node for it, and add DMA channels for existing peripherals.

---
Changes since v1:
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi +41 -0
index d549d277d972..885809137b9d 100644
@@ -133,6 +133,19 @@ ccu: clock@3001000 {
 			#reset-cells = <1>;
 		};
 
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun50i-h616-dma",
+				     "allwinner,sun50i-a100-dma";
+			reg = <0x03002000 0x1000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			dma-channels = <16>;
+			dma-requests = <49>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		sid: efuse@3006000 {
 			compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
 			reg = <0x03006000 0x1000>;
@@ -339,6 +352,8 @@ uart0: serial@5000000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART0>;
+			dmas = <&dma 14>, <&dma 14>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
@@ -350,6 +365,8 @@ uart1: serial@5000400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART1>;
+			dmas = <&dma 15>, <&dma 15>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
@@ -361,6 +378,8 @@ uart2: serial@5000800 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART2>;
+			dmas = <&dma 16>, <&dma 16>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
@@ -372,6 +391,8 @@ uart3: serial@5000c00 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART3>;
+			dmas = <&dma 17>, <&dma 17>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART3>;
 			status = "disabled";
 		};
@@ -383,6 +404,8 @@ uart4: serial@5001000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART4>;
+			dmas = <&dma 18>, <&dma 18>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART4>;
 			status = "disabled";
 		};
@@ -394,6 +417,8 @@ uart5: serial@5001400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART5>;
+			dmas = <&dma 19>, <&dma 19>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART5>;
 			status = "disabled";
 		};
@@ -405,6 +430,8 @@ i2c0: i2c@5002000 {
 			reg = <0x05002000 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C0>;
+			dmas = <&dma 43>, <&dma 43>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C0>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&i2c0_pins>;
@@ -420,6 +447,8 @@ i2c1: i2c@5002400 {
 			reg = <0x05002400 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
+			dmas = <&dma 44>, <&dma 44>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -433,6 +462,8 @@ i2c2: i2c@5002800 {
 			reg = <0x05002800 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
+			dmas = <&dma 45>, <&dma 45>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -446,6 +477,8 @@ i2c3: i2c@5002c00 {
 			reg = <0x05002c00 0x400>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C3>;
+			dmas = <&dma 46>, <&dma 46>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C3>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -459,6 +492,8 @@ i2c4: i2c@5003000 {
 			reg = <0x05003000 0x400>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C4>;
+			dmas = <&dma 47>, <&dma 47>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C4>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -472,6 +507,8 @@ spi0: spi@5010000 {
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 22>, <&dma 22>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI0>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -485,6 +522,8 @@ spi1: spi@5011000 {
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 23>, <&dma 23>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -734,6 +773,8 @@ r_i2c: i2c@7081400 {
 			reg = <0x07081400 0x400>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			dmas = <&dma 48>, <&dma 48>;
+			dma-names = "rx", "tx";
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;
Signature · 1 line
2.39.2
author maintainer
#10 lore raw

PATCH v2 7/7 arm64: dts: allwinner: h616: Add SPDIF device node

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The H616 SoC has an SPDIF transmitter hardware block, which has the same layout as the one in the H6, minus the receiver side.

Add a device node for it, and a default pinmux.

---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi +20 -0
index 885809137b9d..b1bf4fb5fc58 100644
@@ -253,6 +253,11 @@ spi1_cs0_pin: spi1-cs0-pin {
 				function = "spi1";
 			};
 
+			spdif_tx_pin: spdif-tx-pin {
+				pins = "PH4";
+				function = "spdif";
+			};
+
 			uart0_ph_pins: uart0-ph-pins {
 				pins = "PH0", "PH1";
 				function = "uart0";
@@ -550,6 +555,21 @@ mdio0: mdio {
 			};
 		};
 
+		spdif: spdif@5093000 {
+			compatible = "allwinner,sun50i-h616-spdif";
+			reg = <0x05093000 0x400>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+			clock-names = "apb", "spdif";
+			resets = <&ccu RST_BUS_SPDIF>;
+			dmas = <&dma 2>;
+			dma-names = "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spdif_tx_pin>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
 		usbotg: usb@5100000 {
 			compatible = "allwinner,sun50i-h616-musb",
 				     "allwinner,sun8i-h3-musb";
Signature · 1 line
2.39.2
Acked-by on v2 4/7
#5 lore raw

Re: [PATCH v2 4/7] dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616

In reply to Chen-Yu Tsai
Quoted 10 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The DMA controllers found on the H616 and H618 are the same as the one found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Since the number of channels and endpoints are described with additional generic properties, just add a new H616-specific compatible string and fallback to the A100 one.

Cheers,
Conor.

Quoted 41 lines

---
Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6

 .../bindings/dma/allwinner,sun50i-a64-dma.yaml       | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml +8 -4
index ec2d7a789ffe..0f2501f72cca 100644
@@ -28,6 +28,9 @@ properties:
       - items:
           - const: allwinner,sun8i-r40-dma
           - const: allwinner,sun50i-a64-dma
+      - items:
+          - const: allwinner,sun50i-h616-dma
+          - const: allwinner,sun50i-a100-dma
 
   reg:
     maxItems: 1
@@ -59,10 +62,11 @@ required:
 if:
   properties:
     compatible:
-      enum:
-        - allwinner,sun20i-d1-dma
-        - allwinner,sun50i-a100-dma
-        - allwinner,sun50i-h6-dma
+      contains:
+        enum:
+          - allwinner,sun20i-d1-dma
+          - allwinner,sun50i-a100-dma
+          - allwinner,sun50i-h6-dma
 
 then:
   properties:
Signature · 1 line
2.39.2
Reviewed-by on v2 6/7
#9 lore raw

Re: [PATCH v2 6/7] arm64: dts: allwinner: h616: Add DMA controller and DMA channels

In reply to Chen-Yu Tsai
Quoted 6 lines · On Sun, 28 Jan 2024 00:32:46 +0800 Chen-Yu Tsai <[email protected]> wrote:

From: Chen-Yu Tsai <[email protected]>

The DMA controllers found on the H616 and H618 are the same as the one found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Add a device node for it, and add DMA channels for existing peripherals.

Thanks for the changes! I compared all bits against the manual: they match.

Quoted 1 line

Cheers,
Andre

Quoted 158 lines

---
Changes since v1:
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi +41 -0
index d549d277d972..885809137b9d 100644
@@ -133,6 +133,19 @@ ccu: clock@3001000 {
 			#reset-cells = <1>;
 		};
 
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun50i-h616-dma",
+				     "allwinner,sun50i-a100-dma";
+			reg = <0x03002000 0x1000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			dma-channels = <16>;
+			dma-requests = <49>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		sid: efuse@3006000 {
 			compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
 			reg = <0x03006000 0x1000>;
@@ -339,6 +352,8 @@ uart0: serial@5000000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART0>;
+			dmas = <&dma 14>, <&dma 14>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
@@ -350,6 +365,8 @@ uart1: serial@5000400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART1>;
+			dmas = <&dma 15>, <&dma 15>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
@@ -361,6 +378,8 @@ uart2: serial@5000800 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART2>;
+			dmas = <&dma 16>, <&dma 16>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
@@ -372,6 +391,8 @@ uart3: serial@5000c00 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART3>;
+			dmas = <&dma 17>, <&dma 17>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART3>;
 			status = "disabled";
 		};
@@ -383,6 +404,8 @@ uart4: serial@5001000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART4>;
+			dmas = <&dma 18>, <&dma 18>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART4>;
 			status = "disabled";
 		};
@@ -394,6 +417,8 @@ uart5: serial@5001400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART5>;
+			dmas = <&dma 19>, <&dma 19>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART5>;
 			status = "disabled";
 		};
@@ -405,6 +430,8 @@ i2c0: i2c@5002000 {
 			reg = <0x05002000 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C0>;
+			dmas = <&dma 43>, <&dma 43>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C0>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&i2c0_pins>;
@@ -420,6 +447,8 @@ i2c1: i2c@5002400 {
 			reg = <0x05002400 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
+			dmas = <&dma 44>, <&dma 44>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -433,6 +462,8 @@ i2c2: i2c@5002800 {
 			reg = <0x05002800 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
+			dmas = <&dma 45>, <&dma 45>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -446,6 +477,8 @@ i2c3: i2c@5002c00 {
 			reg = <0x05002c00 0x400>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C3>;
+			dmas = <&dma 46>, <&dma 46>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C3>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -459,6 +492,8 @@ i2c4: i2c@5003000 {
 			reg = <0x05003000 0x400>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C4>;
+			dmas = <&dma 47>, <&dma 47>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C4>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -472,6 +507,8 @@ spi0: spi@5010000 {
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 22>, <&dma 22>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI0>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -485,6 +522,8 @@ spi1: spi@5011000 {
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 23>, <&dma 23>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -734,6 +773,8 @@ r_i2c: i2c@7081400 {
 			reg = <0x07081400 0x400>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			dmas = <&dma 48>, <&dma 48>;
+			dma-names = "rx", "tx";
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;
maintainer
#11 lore raw
In reply to Chen-Yu Tsai
Quoted 3 lines · Chen-Yu Tsai

Chen-Yu Tsai (7):
dt-bindings: sound: sun4i-spdif: Fix requirements for H6
dt-bindings: sound: sun4i-spdif: Add Allwinner H616 compatible

Please submit patches using subject lines reflecting the style for the subsystem, this makes it easier for people to identify relevant patches. Look at what existing commits in the area you're changing are doing and make sure your subject lines visually resemble what they're doing. There's no need to resubmit to fix this alone.

Reviewed-by on v2 4/7
#6 lore raw

Re: [PATCH v2 4/7] dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616

In reply to Chen-Yu Tsai

On Sun, 28 Jan 2024 00:32:44 +0800
Chen-Yu Tsai <[email protected]> wrote:

Hi,

Quoted 10 lines

From: Chen-Yu Tsai <[email protected]>

The DMA controllers found on the H616 and H618 are the same as the one found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Since the number of channels and endpoints are described with additional generic properties, just add a new H616-specific compatible string and fallback to the A100 one.

Looks good, A100 is the right fallback string. dt-binding_check passed for me.

Cheers,
Andre

Quoted 38 lines

---
Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6

 .../bindings/dma/allwinner,sun50i-a64-dma.yaml       | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/dma/allwinner,sun50i-a64-dma.yaml +8 -4
index ec2d7a789ffe..0f2501f72cca 100644
@@ -28,6 +28,9 @@ properties:
       - items:
           - const: allwinner,sun8i-r40-dma
           - const: allwinner,sun50i-a64-dma
+      - items:
+          - const: allwinner,sun50i-h616-dma
+          - const: allwinner,sun50i-a100-dma
 
   reg:
     maxItems: 1
@@ -59,10 +62,11 @@ required:
 if:
   properties:
     compatible:
-      enum:
-        - allwinner,sun20i-d1-dma
-        - allwinner,sun50i-a100-dma
-        - allwinner,sun50i-h6-dma
+      contains:
+        enum:
+          - allwinner,sun20i-d1-dma
+          - allwinner,sun50i-a100-dma
+          - allwinner,sun50i-h6-dma
 
 then:
   properties:
maintainer
#12 lore raw

Re: (subset) [PATCH v2 0/7] arm64: sun50i-h616: Add DMA and SPDIF controllers

In reply to Chen-Yu Tsai
Quoted 8 lines · Chen-Yu Tsai

This is v2 of my H616/H618 DMA and SPDIF controller series.

Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next

Thanks!

[1/7] dt-bindings: sound: sun4i-spdif: Fix requirements for H6

      commit: 57b3c130d97e45b8a07586e0ae113e43776c5ea8
[2/7] dt-bindings: sound: sun4i-spdif: Add Allwinner H616 compatible
      commit: 7a9dc944f129bb56ef855d9c0b0647bc3e98a56f
[3/7] ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
      commit: 0adf963b8463faa44653e22e56ce55f747e68868

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

maintainer Applied
#13 lore raw

Re: (subset) [PATCH v2 0/7] arm64: sun50i-h616: Add DMA and SPDIF controllers

In reply to Chen-Yu Tsai
Quoted 8 lines · Chen-Yu Tsai

This is v2 of my H616/H618 DMA and SPDIF controller series.

Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

[...]

Applied, thanks!

[4/7] dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616

      commit: b32eb97edeb8d69092d57419917b19c909ff962a

Best regards,

Signature · 1 line
~Vinod
maintainer Applied
#14 lore raw
In reply to Chen-Yu Tsai

Dne sobota, 27. januar 2024 ob 17:32:40 CET je Chen-Yu Tsai napisal(a):

Quoted 56 lines

From: Chen-Yu Tsai <[email protected]>

Hi everyone,

This is v2 of my H616/H618 DMA and SPDIF controller series.

Changes since v1:
- Switch to "contains" for if-properties statement
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

This series adds DMA and SPDIF controllers for the H616 and H618. There's also a fix for SPDIF on H6: the controller also has a receiver that was not correctly modeled.

Patch 1 fixes the binding for the SPDIF controller on the H6 by adding the RX DMA channel.

Patch 2 adds a compatible string for the H616's SPDIF transmitter to the binding.

Patch 3 adds a compatible string for the H616's SPDIF transmitter to the driver.

Patch 4 adds a compatible string for the H616's DMA controller.

Patch 5 adds the RX DMA channel to the SPDIF controller on the H6.

Patch 6 adds a device node for the H616's DMA controller.

Patch 7 adds a device node for the H616's SPDIF controller.

This was tested on the Orange Pi Zero 3 with SPI flash transfers and SPDIF audio output. The H6 SPDIF change is superficial as the driver does not support receiving / capturing an audio stream.

Please have a look. I expect the first three patches to go through the ASoC tree, the fourth patch to either go through the DMA tree, or through the sunxi tree with an Ack, and the last three through the sunxi tree.

Thanks
ChenYu

Chen-Yu Tsai (7):
dt-bindings: sound: sun4i-spdif: Fix requirements for H6
dt-bindings: sound: sun4i-spdif: Add Allwinner H616 compatible
ASoC: sunxi: sun4i-spdif: Add support for Allwinner H616
dt-bindings: dma: allwinner,sun50i-a64-dma: Add compatible for H616
arm64: dts: allwinner: h6: Add RX DMA channel for SPDIF
arm64: dts: allwinner: h616: Add DMA controller and DMA channels
arm64: dts: allwinner: h616: Add SPDIF device node

Quoted 10 lines
 .../dma/allwinner,sun50i-a64-dma.yaml         | 12 ++--
 .../sound/allwinner,sun4i-a10-spdif.yaml      |  5 +-
 .../dts/allwinner/sun50i-h6-beelink-gs1.dts   |  2 +
 .../boot/dts/allwinner/sun50i-h6-tanix.dtsi   |  2 +
 arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi  |  7 +--
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 61 +++++++++++++++++++
 sound/soc/sunxi/sun4i-spdif.c                 |  5 ++
 7 files changed, 85 insertions(+), 9 deletions(-)

Applied patches 5-7 to sunxi tree, thanks!

Best regards,
Jernej