Turris Omnia - New board revision support
cover Turris Omnia - New board revision support
Hi Stefan,
a new board revision of Omnia is coming. In this new revision the board information (serial number, MAC address) and board cryptography is implemented by the microcontroller. The ATSHA204A cryptochip is not present on this new revision.
Here are some changes regarding this.
Marek
Marek Behún (4):
arm: mvebu: turris_omnia: Refactor MCU status and features reading
arm: mvebu: turris_omnia: Implement getting board information from MCU
arm: mvebu: turris_omnia: Print board ECDSA public key if available
arm: mvebu: turris_omnia: Disable Atmel SHA node if not present
board/CZ.NIC/turris_atsha_otp.c | 27 +-- board/CZ.NIC/turris_common.c | 42 +++++ board/CZ.NIC/turris_common.h | 10 + board/CZ.NIC/turris_omnia/Makefile | 2 +- board/CZ.NIC/turris_omnia/turris_omnia.c | 229 +++++++++++++++++++---- 5 files changed, 252 insertions(+), 58 deletions(-) create mode 100644 board/CZ.NIC/turris_common.c create mode 100644 board/CZ.NIC/turris_common.h
Signature · 1 line
2.43.0
PATCH 2/4 arm: mvebu: turris_omnia: Implement getting board information from MCU
Implement reading board serial number, first MAC address and board version from MCU. MCU supports board information if the FEAT_BOARD_INFO feature bit is set in MCU features.
Prefer getting board information from MCU if supported, fallback to Atmel SHA chip.
--- board/CZ.NIC/turris_atsha_otp.c | 27 +------ board/CZ.NIC/turris_common.c | 42 ++++++++++ board/CZ.NIC/turris_common.h | 10 +++ board/CZ.NIC/turris_omnia/Makefile | 2 +- board/CZ.NIC/turris_omnia/turris_omnia.c | 98 +++++++++++++++++++++++- 5 files changed, 149 insertions(+), 30 deletions(-) create mode 100644 board/CZ.NIC/turris_common.c create mode 100644 board/CZ.NIC/turris_common.h
board/CZ.NIC/turris_atsha_otp.c +2 -25
@@ -11,6 +11,7 @@#include <atsha204a-i2c.h> #include "turris_atsha_otp.h" +#include "turris_common.h" #define TURRIS_ATSHA_OTP_VERSION 0#define TURRIS_ATSHA_OTP_SERIAL 1
@@ -32,26 +33,6 @@ static struct udevice *get_atsha204a_dev(void)return dev; } -static void increment_mac (u8 *mac) -{ -int i; - -for (i =5 ; i >=3 ; i--) { - mac[i] +=1 ; -if (mac[i]) -break ; - } -} - -static void set_mac_if_invalid (int i,u8 *mac) -{ -u8 oldmac[6 ]; - -if (is_valid_ethaddr (mac) && - !eth_env_get_enetaddr_by_index ("eth" , i, oldmac)) -eth_env_set_enetaddr_by_index ("eth" , i, mac); -} -int turris_atsha_otp_init_mac_addresses (int first_idx) {struct udevice *dev =get_atsha204a_dev ();
@@ -84,11 +65,7 @@ int turris_atsha_otp_init_mac_addresses(int first_idx) mac[4 ] = mac1[2 ]; mac[5 ] = mac1[3 ]; -set_mac_if_invalid ((first_idx +0 ) %3 , mac); -increment_mac (mac); -set_mac_if_invalid ((first_idx +1 ) %3 , mac); -increment_mac (mac); -set_mac_if_invalid ((first_idx +2 ) %3 , mac); +turris_init_mac_addresses (first_idx, mac);return 0 ; }
board/CZ.NIC/turris_common.c new file +42 -0
42 lines not on this page · raw message
board/CZ.NIC/turris_common.h new file +10 -0
@@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +#ifndef TURRIS_COMMON_H +#define TURRIS_COMMON_H + +#include <asm/types.h> + +void turris_init_mac_addresses (int first_idx,const u8 *first_mac); + +#endif
board/CZ.NIC/turris_omnia/Makefile +1 -1
@@ -2,4 +2,4 @@ # # Copyright (C) 2017 Marek Behún <[email protected]> -obj-y := turris_omnia.o ../turris_atsha_otp.o +obj-y := turris_omnia.o ../turris_atsha_otp.o ../turris_common.o
board/CZ.NIC/turris_omnia/turris_omnia.c +94 -4
152 lines not on this page · raw message
Signature · 1 line
2.43.0
PATCH 1/4 arm: mvebu: turris_omnia: Refactor MCU status and features reading
In reply to Marek BehúnRefactor MCU status word and MCU firmware features reading to make it simpler to use.
--- board/CZ.NIC/turris_omnia/turris_omnia.c | 81 ++++++++++++++++-------- 1 file changed, 53 insertions(+), 28 deletions(-)
board/CZ.NIC/turris_omnia/turris_omnia.c +53 -28
@@ -172,6 +172,48 @@ static int omnia_mcu_write(u8 cmd, const void *buf, int len)return dm_i2c_write (chip, cmd, buf, len); } +static int omnia_mcu_get_sts_and_features (u16 *psts,u16 *pfeatures) +{ +u16 sts; +int ret; + + ret =omnia_mcu_read (CMD_GET_STATUS_WORD , &sts,sizeof (sts)); +if (ret) +return ret; + +if (psts) + *psts = sts; + +if (!pfeatures) +return 0 ; + +if (sts &STS_FEATURES_SUPPORTED ) { + ret =omnia_mcu_read (CMD_GET_FEATURES , pfeatures, +sizeof (*pfeatures)); +if (ret) +return ret; + }else { + *pfeatures =0 ; + } + +return 0 ; +} + +static int omnia_mcu_get_sts (u16 *sts) +{ +return omnia_mcu_get_sts_and_features (sts,NULL ); +} + +static bool omnia_mcu_has_feature (u16 feature) +{ +u16 features; + +if (omnia_mcu_get_sts_and_features (NULL , &features)) +return false; + +return feature & features; +} +static void enable_a385_watchdog (unsigned int timeout_minutes) {struct sar_freq_modes sar_freq;
@@ -249,7 +291,7 @@ static bool omnia_detect_sata(const char *msata_slot) } } - ret =omnia_mcu_read (CMD_GET_STATUS_WORD , &stsword,sizeof (stsword)); + ret =omnia_mcu_get_sts (&stsword);if (ret) {printf ("omnia_mcu_read failed: %i, defaulting to MiniPCIe card\n" , ret);
@@ -405,20 +447,17 @@ static const char * const omnia_get_mcu_type(void) [STS_MCU_TYPE_MKL] = "MKL (with peripheral resets)", [STS_MCU_TYPE_UNKN] = "unknown (with peripheral resets)", }; -u16 stsword, features; +u16 sts;int ret; - ret =omnia_mcu_read (CMD_GET_STATUS_WORD , &stsword,sizeof (stsword)); + ret =omnia_mcu_get_sts (&sts);if (ret)return "unknown" ; -if (stsword &STS_FEATURES_SUPPORTED ) { - ret =omnia_mcu_read (CMD_GET_FEATURES , &features,sizeof (features)); -if (ret ==0 && (features &FEAT_PERIPH_MCU )) -return mcu_types_with_perip_resets[stsword &STS_MCU_TYPE_MASK ]; - } +if (omnia_mcu_has_feature (FEAT_PERIPH_MCU )) +return mcu_types_with_perip_resets[sts &STS_MCU_TYPE_MASK ]; -return mcu_types[stsword &STS_MCU_TYPE_MASK ]; +return mcu_types[sts &STS_MCU_TYPE_MASK ]; }static const char *const omnia_get_mcu_version (void )
@@ -695,9 +734,6 @@ int board_early_init_f(void)void spl_board_init (void ) { -u16 val; -int ret; -/* * If booting from UART, disable MCU watchdog in SPL, since uploading * U-Boot proper can take too much time and trigger it. Instead enable
@@ -714,12 +750,8 @@ void spl_board_init(void)* resets then LAN eth switch is initialized automatically by bootstrap * pins when A385 is released from the reset. */ - ret =omnia_mcu_read (CMD_GET_STATUS_WORD , &val,sizeof (val)); -if (ret ==0 && (val &STS_FEATURES_SUPPORTED )) { - ret =omnia_mcu_read (CMD_GET_FEATURES , &val,sizeof (val)); -if (ret ==0 && (val &FEAT_PERIPH_MCU )) -initialize_switch (); - } +if (omnia_mcu_has_feature (FEAT_PERIPH_MCU )) +initialize_switch (); }#if IS_ENABLED (CONFIG_OF_BOARD_FIXUP ) ||IS_ENABLED (CONFIG_OF_BOARD_SETUP )
@@ -919,16 +951,9 @@ static int fixup_mcu_gpio_in_eth_wan_node(void *blob)#if IS_ENABLED (CONFIG_OF_BOARD_FIXUP )int board_fix_fdt (void *blob) { -u16 val; -int ret; - - ret =omnia_mcu_read (CMD_GET_STATUS_WORD , &val,sizeof (val)); -if (ret ==0 && (val &STS_FEATURES_SUPPORTED )) { - ret =omnia_mcu_read (CMD_GET_FEATURES , &val,sizeof (val)); -if (ret ==0 && (val &FEAT_PERIPH_MCU )) { -fixup_mcu_gpio_in_pcie_nodes (blob); -fixup_mcu_gpio_in_eth_wan_node (blob); - } +if (omnia_mcu_has_feature (FEAT_PERIPH_MCU )) { +fixup_mcu_gpio_in_pcie_nodes (blob); +fixup_mcu_gpio_in_eth_wan_node (blob); }fixup_msata_port_nodes (blob);
Signature · 1 line
2.43.0
PATCH 3/4 arm: mvebu: turris_omnia: Print board ECDSA public key if available
In reply to Marek BehúnIf MCU supports the FEAT_CRYPTO feature, read board ECDSA public key from MCU and print it.
--- board/CZ.NIC/turris_omnia/turris_omnia.c | 29 +++++++++++++++++++++++- 1 file changed, 28 insertions(+), 1 deletion(-)
board/CZ.NIC/turris_omnia/turris_omnia.c +28 -1
@@ -75,6 +75,9 @@ enum mcu_commands {/* available if EXT_CMD bit set in features */ CMD_EXT_CONTROL =0x12 , +/* available if CRYPTO bit set in features */ +CMD_CRYPTO_GET_PUBLIC_KEY =0x29 , +/* available if BOARD_INFO it set in features */ CMD_BOARD_INFO_GET = 0x2c, };
@@ -94,6 +97,7 @@ enum status_word_bits {enum features_e {FEAT_PERIPH_MCU =BIT (0 ),FEAT_EXT_CMDS =BIT (1 ), +FEAT_CRYPTO =BIT (14 ),FEAT_BOARD_INFO =BIT (15 ), };
@@ -285,6 +289,24 @@ static int omnia_mcu_board_info(char *serial, u8 *mac, char *version)return 0 ; } +static int omnia_mcu_get_board_public_key (char pub_key[static 67 ]) +{ +u8 reply[34 ]; +int ret; + + ret =omnia_mcu_read (CMD_CRYPTO_GET_PUBLIC_KEY , reply,sizeof (reply)); +if (ret) +return ret; + +if (reply[0 ] !=33 ) +return -EBADMSG ; + +bin2hex (pub_key, &reply[1 ],33 ); + reply[66 ] ='\0' ; + +return 0 ; +} +static void enable_a385_watchdog (unsigned int timeout_minutes) {struct sar_freq_modes sar_freq;
@@ -1060,7 +1082,7 @@ int board_late_init(void)int checkboard (void ) { -char serial[17 ], version[4 ]; +char serial[17 ], version[4 ], pub_key[67 ];bool has_version;int err;
@@ -1080,6 +1102,11 @@ int checkboard(void)printf (" Board version: %s\n" , has_version ? version :"unknown" );printf (" Serial Number: %s\n" , !err ? serial :"unknown" ); +if (omnia_mcu_has_feature (FEAT_CRYPTO )) { + err =omnia_mcu_get_board_public_key (pub_key); +printf (" ECDSA Public Key: %s\n" , !err ? pub_key :"unknown" ); + } +return 0 ; }
Signature · 1 line
2.43.0
PATCH 4/4 arm: mvebu: turris_omnia: Disable Atmel SHA node if not present
In reply to Marek BehúnIf the FEAT_CRYPTO feature bit is present in MCU features, the board crypto is implemented by MCU and the Atmel SHA chip is not present. Disable Atmel SHA device-tree node in that case.
--- board/CZ.NIC/turris_omnia/turris_omnia.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
board/CZ.NIC/turris_omnia/turris_omnia.c +23 -0
@@ -1039,6 +1039,25 @@ static int fixup_mcu_gpio_in_eth_wan_node(void *blob) return 0; } +static void fixup_atsha_node (void *blob) +{ +int node; + +if (!omnia_mcu_has_feature (FEAT_CRYPTO )) +return ; + + node =fdt_node_offset_by_compatible (blob,-1 ,"atmel,atsha204a" ); +if (node <0 ) { +printf ("Cannot find ATSHA204A node!\n" ); +return ; + } + +if (fdt_status_disabled (blob, node) <0 ) +printf ("Cannot disable ATSHA204A node!\n" ); +else +debug ("Disabled ATSHA204A node\n" ); +} +#endif #if IS_ENABLED (CONFIG_OF_BOARD_FIXUP )
@@ -1052,6 +1071,8 @@ int board_fix_fdt(void *blob)fixup_msata_port_nodes (blob);fixup_wwan_port_nodes (blob); +fixup_atsha_node (blob); + return 0; }#endif
@@ -1244,6 +1265,8 @@ int ft_board_setup(void *blob, struct bd_info *bd)fixup_msata_port_nodes (blob);fixup_wwan_port_nodes (blob); +fixup_atsha_node (blob); + return 0; }#endif
Signature · 1 line
2.43.0
Hello Stefan,
I've been doing some work on this and will be sending version 2 of this series.
Marek