PCI: Use the correct bit in Link Training not active check
PATCH v2 1/2 PCI: Use the correct bit in Link Training not active check
Two changes were made into link retraining logic independent of each other.
The commit e7e39756363a ("PCI/ASPM: Avoid link retraining race") added check to ensure no Link Training is currently active into pcie_retrain_link() to address the Implementation Note in PCIe r6.1 sec 7.5.3.7. At that time pcie_wait_for_retrain() only checked for Link Training (LT) bit being cleared.
The commit 680e9c47a229 ("PCI: Add support for polling DLLLA to pcie_retrain_link()") generalized pcie_wait_for_retrain() into pcie_wait_for_link_status() which can wait either for LT or Data Link Layer Link Active (DLLLA) bit with 'use_lt' argument and supporting waiting for either cleared or set using 'active' argument.
In the merge commit commit 1abb47390350 ("Merge branch 'pci/enumeration'"), those two divergent branches converged. The merge changed LT bit checking added in the commit e7e39756363a ("PCI/ASPM:
Avoid link retraining race") to now wait for completion of any ongoing Link Training using DLLLA bit being set if 'use_lt' is false.
When 'use_lt' is false, the pseudo-code steps of what occurs in pcie_retrain_link():
1. Wait for DLLLA=1
2. Trigger link to retrain
3. Wait for DLLLA=1
Step 3 waits for the link to come up from the retraining triggered by Step 2. As Step 1 is supposed to wait for any ongoing retraining to end, using DLLLA also for it does not make sense because link training being active is still indicated using LT bit, not with DLLLA.
Correct the pcie_wait_for_link_status() parameters in Step 1 to only wait for LT=0 to ensure there is no ongoing Link Training.
This only impacts the Target Speed quirk, which is the only case where waiting for DLLLA bit is used. It currently works in the problematic case by means of link training getting initiated by hardware repeatedly and respecting the new link parameters set by the caller, which then make training succeed and bring the link up, setting DLLLA and causing pcie_wait_for_link_status() to return success. We are not supposed to rely on luck and need to make sure that LT transitioned through the inactive state though before we initiate link training by hand via RL (Retrain Link) bit.
---
v2:
- Improve commit message
NOTE: Maciej NAK'ed the v1 of this patch but has since retracted his NAK.
Maciej, if possible, could you please test this with your HW?
--- drivers/pci/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/pci/pci.c +1 -1
@@ -4629,7 +4629,7 @@ int pcie_retrain_link(struct pci_dev *pdev, bool use_lt)* avoid LTSSM race as recommended in Implementation Note at the * end of PCIe r6.0.1 sec 7.5.3.7. */ - rc =pcie_wait_for_link_status (pdev, use_lt, !use_lt); + rc =pcie_wait_for_link_status (pdev, true, false);if (rc)return rc;
Signature · 1 line
2.39.2
PATCH v2 2/2 PCI: Small clarification to the intent of LT wait
Make a small clarification into the comment relating to the LT wait and the purpose of the check that implements the implementation note in PCIe r6.1 sec 7.5.3.7.
---
v2:
- New patch
--- drivers/pci/pci.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/pci/pci.c +4 -3
@@ -4625,9 +4625,10 @@ int pcie_retrain_link(struct pci_dev *pdev, bool use_lt)/* * Ensure the updated LNKCTL parameters are used during link -* training by checking that there is no ongoing link training to -* avoid LTSSM race as recommended in Implementation Note at the -* end of PCIe r6.0.1 sec 7.5.3.7. +* training by checking that there is no ongoing link training that +* may have started before link parameters were changed, so as to +* avoid LTSSM race as recommended in Implementation Note at the end +* of PCIe r6.1 sec 7.5.3.7. */ rc =pcie_wait_for_link_status (pdev, true, false);if (rc)
Signature · 1 line
2.39.2
Quoted 7 lines · Ilpo Järvinen
v2:
- Improve commit messageNOTE: Maciej NAK'ed the v1 of this patch but has since retracted his NAK.
Maciej, if possible, could you please test this with your HW?
I'll try before the end of this week, thanks for your work in this area.
Maciej
Bjorn Helgaas
AppliedQuoted 46 lines · Ilpo Järvinen
Two changes were made into link retraining logic independent of each other.
The commit
e7e39756363a("PCI/ASPM: Avoid link retraining race") added check to ensure no Link Training is currently active intopcie_retrain_link()to address the Implementation Note in PCIe r6.1 sec 7.5.3.7. At that timepcie_wait_for_retrain()only checked for Link Training (LT) bit being cleared.The commit
680e9c47a229("PCI: Add support for polling DLLLA topcie_retrain_link()") generalizedpcie_wait_for_retrain()intopcie_wait_for_link_status()which can wait either for LT or Data Link Layer Link Active (DLLLA) bit with 'use_lt' argument and supporting waiting for either cleared or set using 'active' argument.In the merge commit commit
1abb47390350("Merge branch 'pci/enumeration'"), those two divergent branches converged. The merge changed LT bit checking added in the commite7e39756363a("PCI/ASPM:
Avoid link retraining race") to now wait for completion of any ongoing Link Training using DLLLA bit being set if 'use_lt' is false.When '
use_lt' is false, the pseudo-code steps of what occurs inpcie_retrain_link():1. Wait for DLLLA=1
2. Trigger link to retrain
3. Wait for DLLLA=1Step 3 waits for the link to come up from the retraining triggered by Step 2. As Step 1 is supposed to wait for any ongoing retraining to end, using DLLLA also for it does not make sense because link training being active is still indicated using LT bit, not with DLLLA.
Correct the
pcie_wait_for_link_status()parameters in Step 1 to only wait for LT=0 to ensure there is no ongoing Link Training.This only impacts the Target Speed quirk, which is the only case where waiting for DLLLA bit is used. It currently works in the problematic case by means of link training getting initiated by hardware repeatedly and respecting the new link parameters set by the caller, which then make training succeed and bring the link up, setting DLLLA and causing
pcie_wait_for_link_status()to return success. We are not supposed to rely on luck and need to make sure that LT transitioned through the inactive state though before we initiate link training by hand via RL (Retrain Link) bit.
Quoted 2 lines
Fixes 1abb47390350 ("Merge branch 'pci/enumeration'")Signed-off-by Ilpo Järvinen <[email protected]>
I applied both of these with minor typo fixes to pci/enumeration for v6.10, thanks!
73cb3a35f94d ("PCI: Wait for Link Training==0 before starting Link retrain") cdc6c4abcb31 ("PCI: Clarify intent of LT wait")
We can update if needed based on feedback from Maciej.
Quoted 30 lines
---
v2:
- Improve commit messageNOTE: Maciej NAK'ed the v1 of this patch but has since retracted his NAK.
Maciej, if possible, could you please test this with your HW?
--- drivers/pci/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/pci/pci.c +1
-1@@ -4629,7 +4629,7 @@ int pcie_retrain_link(struct pci_dev *pdev, bool use_lt)* avoid LTSSM race as recommended in Implementation Note at the * end of PCIe r6.0.1 sec 7.5.3.7. */ - rc =pcie_wait_for_link_status (pdev, use_lt, !use_lt); + rc =pcie_wait_for_link_status (pdev, true, false);if (rc)return rc;Signature · 1 line
2.39.2