mmc: core: check R1_STATUS for erase/trim/discard
PATCH 1/1 mmc: core: check R1_STATUS for erase/trim/discard
When erase/trim/discard completion was converted to mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhci card->busy() could return busy for long periods to cause mmc_do_erase() to block during discard operation as shown below during mkfs.f2fs :
Info: [/dev/mmcblk1p9] Discarding device
[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0 [ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16c
Fix skips the card->busy() and uses MMC_SEND_STATUS and R1_STATUS check for MMC_ERASE_BUSY busy_cmd case in the mmc_busy_cb() function.
--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/mmc/core/mmc_ops.c +2 -1
@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err; -if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }
Signature · 1 line
2.17.1
Quoted 45 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0 [ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16c
Quoted 5 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>
Thanks!
Signature · 1 line
Florian
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0
Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16c
Thanks for the detailed log!
Quoted 15 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 9 lines
drivers/mmc/core/mmc_ops.c +2
-1@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err; -if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }
So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
I would suggest that we first try to fix the implementation of the ->card_busy() callback for your HW. If that isn't possible or fails, then let's consider the approach you have taken in the $subject patch.
Kind regards
Uffe
Quoted 87 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 15 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 9 lines
drivers/mmc/core/mmc_ops.c +2
-1@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err; -if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
Quoted 3 lines
I would suggest that we first try to fix the implementation of the ->card_busy() callback for your HW. If that isn't possible or fails, then let's consider the approach you have taken in the $subject patch.
Note, sdhci drivers can override host->ops. For example, sdhci-omap.c has:
host->mmc_host_ops.card_busy = sdhci_omap_card_busy;
Probably, if ->card_busy() cannot be supported, then setting it to NULL would work.
host->mmc_host_ops.card_busy = NULL; /* Cannot detect card busy */
Quoted 71 lines · Adrian Hunter
Quoted 69 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 18 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err;
Quoted 11 lines
Quoted 11 lines
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 6 lines
drivers/mmc/core/mmc_ops.c +2
-1-if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
Using the sdhci-brcmstb driver on a Broadcom Settop based SoC.
Quoted 7 lines
Quoted 7 lines
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
I have tested two scenarios. One is like the mkfs.f2fs app that calls :ioctl(fd, BLKSECDISCARD, &range);
This has the following CMD and completion sequence:
{CMD35->CMD36->CMD38} and poll for DAT0 signal via card->busy . CMD38 has a response of R1b. The DAT0 (Busy line) will be driven by the device. Busy (DAT0 = 0) is asserted by a device for erasing blocks. Stays busy in brcmstb sdhci controller.
With the additional change followed by CMD13 (response of R1), which returns the device status, the
DAT0 will be pulled-up and next time we read the BUSY status it will indicate it is not busy.
Also I tried the mmc util and that does not show the same issue with exactly the same ranges, however in that case there are some differences in the way the CMD sequence is sent for the entire discard operation.
# mmc erase discard 0x000087a4 0x002effff /dev/mmcblk1 /* send erase cmd with multi-cmd */ ret = ioctl(dev_fd, MMC_IOC_MULTI_CMD, multi_cmd);
CMD35->CMD13->CMD36->CMD13->CMD38->CMD13
I do not see any hang in all the erase options discard, legacy, trim, trim2, secure-trim used here with mmc util .
Also looking at JEDEC Standard No. 84-B51 Page 276, 277 "Once the erase groups are selected the host will send an ERASE (CMD38) command. It is recom-
mended that the host terminates the sequence with a SEND_STATUS (CMD13) to poll any additional
status information the Device may have (e.g., WP_ERASE_SKIP, etc.)."
Quoted 4 lines
Quoted 3 lines
I would suggest that we first try to fix the implementation of the ->card_busy() callback for your HW. If that isn't possible or fails, then let's consider the approach you have taken in the $subject patch.
I have verified this with hardware behavior and default sdhci->card->busy() seems to work fine except
in the above sequence of CMD35->CMD36->CMD38 without any MMC_STATUS interleaved.
Maybe we can do both, check the card busy and send CMD13. __mmc_poll_for_busy() does have
throttling changes as well that would limit the rate at which CMD13 will be sent.
Quoted 10 lines
Note, sdhci drivers can override
host->ops. For example,sdhci-omap.chas:host->mmc_host_ops.card_busy = sdhci_omap_card_busy;Probably, if ->card_busy() cannot be supported, then setting it to NULL would work.
host->mmc_host_ops.card_busy = NULL; /* Cannot detect card busy */
Yes, that's an option I have tested to be working and will have to take in case mmc_busy_cb() change is not acceptable.
Thanks
Kamal
Quoted 95 lines · Kamal Dasu
Quoted 71 lines · Adrian Hunter
Quoted 69 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 18 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err;Quoted 11 lines
Quoted 11 lines
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 6 lines
drivers/mmc/core/mmc_ops.c +2
-1-if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
Using the sdhci-brcmstb driver on a Broadcom Settop based SoC.
Quoted 7 lines
Quoted 7 lines
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
Quoted 8 lines
I have tested two scenarios. One is like the mkfs.f2fs app that calls :
ioctl(fd, BLKSECDISCARD, &range);This has the following CMD and completion sequence:
{CMD35->CMD36->CMD38} and poll for DAT0 signal viacard->busy. CMD38 has a response of R1b. The DAT0 (Busy line) will be driven by the device. Busy (DAT0 = 0) is asserted by a device for erasing blocks. Stays busy in brcmstb sdhci controller.
How big is the "range"?
Just so I get this right, it stays busy and we are waiting for the timeout to fire? And ideally you think we should not be busy for that long, right?
Quoted 5 lines
With the additional change followed by CMD13 (response of R1), which returns the device status, the
DAT0 will be pulled-up and next time we read the BUSY status it will indicate it is not busy.
So you are referring to read the BUSY status with you ->card_busy() callback? Or did you actually verify that this is true from an electrical point of view, by monitoring the DAT0 signal?
If the latter, perhaps it's the card that is failing and simply requires CMD13 to be used to poll for busy. What card is this?
Have you tried different cards with the same platform/driver?
Quoted 5 lines
Also I tried the mmc util and that does not show the same issue with exactly the same ranges, however in that case there are some differences in the way the CMD sequence is sent for the entire discard operation.
Quoted 7 lines
# mmc erase discard 0x000087a4 0x002effff /dev/mmcblk1 /* send erase cmd with multi-cmd */ ret = ioctl(dev_fd, MMC_IOC_MULTI_CMD, multi_cmd);
CMD35->CMD13->CMD36->CMD13->CMD38->CMD13
I do not see any hang in all the erase options discard, legacy, trim, trim2, secure-trim used here with mmc util .
So CMD13 seems to do the trick for you. Although, I think we need to figure out if this a special "broken" card or if the problem is with the ->card_busy() implementation for your platform.
Quoted 7 lines
Also looking at JEDEC Standard No. 84-B51 Page 276, 277 "Once the erase groups are selected the host will send an ERASE (CMD38) command. It is recom-
mended that the host terminates the sequence with aSEND_STATUS(CMD13) to poll any additional
status information the Device may have (e.g.,WP_ERASE_SKIP, etc.)."
Isn't that exactly what is being done? After the card has stopped signaling busy, we send a CMD13 in mmc_busy_cb() to read the additional status information.
I don't get it, why should the card stop signal busy, just because we send a CMD13. If so, the card should probably be considered broken. For broken cards, we can try to use a card-quirk instead - to enforce CMD13 polling.
Quoted 6 lines
Quoted 5 lines
Quoted 4 lines
I would suggest that we first try to fix the implementation of the ->card_busy() callback for your HW. If that isn't possible or fails, then let's consider the approach you have taken in the $subject patch.
Quoted 8 lines
I have verified this with hardware behavior and default
sdhci->card->busy()seems to work fine except
in the above sequence ofCMD35->CMD36->CMD38without anyMMC_STATUSinterleaved.Maybe we can do both, check the card busy and send CMD13.
__mmc_poll_for_busy()does have
throttling changes as well that would limit the rate at which CMD13 will be sent.
Polling with both wouldn't help, but make the polling-loop heaviers, we certainly don't want that.
Quoted 9 lines
Quoted 9 lines
Note, sdhci drivers can override
host->ops. For example,sdhci-omap.chas:host->mmc_host_ops.card_busy = sdhci_omap_card_busy;Probably, if ->card_busy() cannot be supported, then setting it to NULL would work.
Quoted 8 lines
Quoted 2 lines
host->mmc_host_ops.card_busy = NULL; /* Cannot detect card busy */Yes, that's an option I have tested to be working and will have to take in case
mmc_busy_cb()change is not acceptable.Thanks
Kamal
Kind regards
Uffe
Quoted 151 lines · Ulf Hansson
Quoted 95 lines · Kamal Dasu
Quoted 71 lines · Adrian Hunter
Quoted 69 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 18 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err;Quoted 11 lines
Quoted 11 lines
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 6 lines
drivers/mmc/core/mmc_ops.c +2
-1-if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
Using the sdhci-brcmstb driver on a Broadcom Settop based SoC.
Quoted 7 lines
Quoted 7 lines
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
Quoted 8 lines
I have tested two scenarios. One is like the mkfs.f2fs app that calls :
ioctl(fd, BLKSECDISCARD, &range);This has the following CMD and completion sequence:
{CMD35->CMD36->CMD38} and poll for DAT0 signal viacard->busy. CMD38 has a response of R1b. The DAT0 (Busy line) will be driven by the device. Busy (DAT0 = 0) is asserted by a device for erasing blocks. Stays busy in brcmstb sdhci controller.How big is the "range"?
Just so I get this right, it stays busy and we are waiting for the timeout to fire? And ideally you think we should not be busy for that long, right?
Quoted 5 lines
With the additional change followed by CMD13 (response of R1), which returns the device status, the
DAT0 will be pulled-up and next time we read the BUSY status it will indicate it is not busy.So you are referring to read the BUSY status with you ->card_busy() callback? Or did you actually verify that this is true from an electrical point of view, by monitoring the DAT0 signal?
If the latter, perhaps it's the card that is failing and simply requires CMD13 to be used to poll for busy. What card is this?
Have you tried different cards with the same platform/driver?
Quoted 5 lines
Also I tried the mmc util and that does not show the same issue with exactly the same ranges, however in that case there are some differences in the way the CMD sequence is sent for the entire discard operation.
Quoted 7 lines
# mmc erase discard 0x000087a4 0x002effff /dev/mmcblk1 /* send erase cmd with multi-cmd */ ret = ioctl(dev_fd, MMC_IOC_MULTI_CMD, multi_cmd);
CMD35->CMD13->CMD36->CMD13->CMD38->CMD13
I do not see any hang in all the erase options discard, legacy, trim, trim2, secure-trim used here with mmc util .So CMD13 seems to do the trick for you. Although, I think we need to figure out if this a special "broken" card or if the problem is with the ->card_busy() implementation for your platform.
Quoted 7 lines
Also looking at JEDEC Standard No. 84-B51 Page 276, 277 "Once the erase groups are selected the host will send an ERASE (CMD38) command. It is recom-
mended that the host terminates the sequence with aSEND_STATUS(CMD13) to poll any additional
status information the Device may have (e.g.,WP_ERASE_SKIP, etc.)."
Quoted 3 lines
Isn't that exactly what is being done? After the card has stopped signaling busy, we send a CMD13 in
mmc_busy_cb()to read the additional status information.
Agreed with your interpretation FWIW.
Quoted 5 lines
I don't get it, why should the card stop signal busy, just because we send a CMD13. If so, the card should probably be considered broken. For broken cards, we can try to use a card-quirk instead - to enforce CMD13 polling.
I'll mention it here, I've seen some broken IP out there where the card's FSM (including busy-signalling) was dependent on the host providing the CLK, can't remember which one it was, though.
Anyway for Kamal, it might be interesting to know if your host controller autostops the CLK (which it is allowed to) during the busy-signalling and if not stopping it also works around the problem.
Quoted 1 line
[snip]
I was testing with different.
Quoted 101 lines · Christian Loehle
Quoted 99 lines · Ulf Hansson
Quoted 98 lines · Kamal Dasu
Quoted 71 lines · Adrian Hunter
Quoted 69 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 18 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err;Quoted 11 lines
Quoted 11 lines
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 6 lines
drivers/mmc/core/mmc_ops.c +2
-1-if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
Using the sdhci-brcmstb driver on a Broadcom Settop based SoC.
Quoted 7 lines
Quoted 7 lines
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
I have tested two scenarios. One is like the mkfs.f2fs app that calls :
ioctl(fd, BLKSECDISCARD, &range);
Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
This has the following CMD and completion sequence:
{CMD35->CMD36->CMD38} and poll for DAT0 signal viacard->busy. CMD38 has a response of R1b. The DAT0 (Busy line) will be driven by the device. Busy (DAT0 = 0) is asserted by a device for erasing blocks. Stays busy in brcmstb sdhci controller.How big is the "range"?
The task just blocks here. I have attached the stack.
Quoted 4 lines
Quoted 4 lines
Just so I get this right, it stays busy and we are waiting for the timeout to fire? And ideally you think we should not be busy for that long, right?
The timeout does not fire.
Quoted 10 lines
Quoted 10 lines
Quoted 5 lines
With the additional change followed by CMD13 (response of R1), which returns the device status, the
DAT0 will be pulled-up and next time we read the BUSY status it will indicate it is not busy.So you are referring to read the BUSY status with you ->card_busy() callback? Or did you actually verify that this is true from an electrical point of view, by monitoring the DAT0 signal?
Quoted 5 lines
Quoted 5 lines
If the latter, perhaps it's the card that is failing and simply requires CMD13 to be used to poll for busy. What card is this?
Have you tried different cards with the same platform/driver?
Yes, I have tried Micron and Sandisk 8GB cards with the same platform with the same results.
Quoted 25 lines
Quoted 25 lines
Quoted 5 lines
Also I tried the mmc util and that does not show the same issue with exactly the same ranges, however in that case there are some differences in the way the CMD sequence is sent for the entire discard operation.
Quoted 7 lines
# mmc erase discard 0x000087a4 0x002effff /dev/mmcblk1 /* send erase cmd with multi-cmd */ ret = ioctl(dev_fd, MMC_IOC_MULTI_CMD, multi_cmd);
CMD35->CMD13->CMD36->CMD13->CMD38->CMD13
I do not see any hang in all the erase options discard, legacy, trim, trim2, secure-trim used here with mmc util .So CMD13 seems to do the trick for you. Although, I think we need to figure out if this a special "broken" card or if the problem is with the ->card_busy() implementation for your platform.
Quoted 7 lines
Also looking at JEDEC Standard No. 84-B51 Page 276, 277 "Once the erase groups are selected the host will send an ERASE (CMD38) command. It is recom-
mended that the host terminates the sequence with aSEND_STATUS(CMD13) to poll any additional
status information the Device may have (e.g.,WP_ERASE_SKIP, etc.)."
Quoted 4 lines
Quoted 3 lines
Isn't that exactly what is being done? After the card has stopped signaling busy, we send a CMD13 in
mmc_busy_cb()to read the additional status information.
Yes, that is what the fix does. However in the original if ->card->busy() is being used we do not send the CMD13.
Quoted 8 lines
Agreed with your interpretation FWIW.
Quoted 5 lines
I don't get it, why should the card stop signal busy, just because we send a CMD13. If so, the card should probably be considered broken. For broken cards, we can try to use a card-quirk instead - to enforce CMD13 polling.
Yes would be one of the solutions that can be considered. Would open to any suggestion on what card-quirk to use.
Quoted 7 lines
I'll mention it here, I've seen some broken IP out there where the card's FSM (including busy-signalling) was dependent on the host providing the CLK, can't remember which one it was, though.
Anyway for Kamal, it might be interesting to know if your host controller autostops the CLK (which it is allowed to) during the busy-signalling and if not stopping it also works around the problem.
The host controller is not stopping the clock. Also stopping the clock does not work around the problem. host is expecting the device FSM pull up the busy line.
At this point I can either do this when adding host:
+ /* we dont use busy signal */
+ host->mmc_host_ops.card_busy = NULL;
Or introduce a card-quirk for this situation.
Kamal
Quoted 133 lines · Kamal Dasu
I was testing with different.
Quoted 101 lines · Christian Loehle
Quoted 99 lines · Ulf Hansson
Quoted 98 lines · Kamal Dasu
Quoted 71 lines · Adrian Hunter
Quoted 69 lines · Ulf Hansson
+ Wolfram, Adrian (to see if they have some input)
Quoted 37 lines · Kamal Dasu
When erase/trim/discard completion was converted to
mmc_poll_for_busy(), optional ->card_busy() host ops support was added. sdhcicard->busy()could return busy for long periods to causemmc_do_erase()to block during discard operation as shown below during mkfs.f2fs :Info: [
/dev/mmcblk1p9] Discarding device[ 39.597258] sysrq: Show Blocked State [ 39.601183] task:mkfs.f2fs state:D stack:0 pid:1561 tgid:1561 ppid:1542 flags:0x0000000d [ 39.610609] Call trace: [ 39.613098] __switch_to+0xd8/0xf4 [ 39.616582] __schedule+0x440/0x4f4 [ 39.620137] schedule+0x2c/0x48 [ 39.623341] schedule_hrtimeout_range_clock+0xe0/0x114 [ 39.628562] schedule_hrtimeout_range+0x10/0x18 [ 39.633169] usleep_range_state+0x5c/0x90 [ 39.637253] __mmc_poll_for_busy+0xec/0x128 [ 39.641514] mmc_poll_for_busy+0x48/0x70 [ 39.645511] mmc_do_erase+0x1ec/0x210 [ 39.649237] mmc_erase+0x1b4/0x1d4 [ 39.652701] mmc_blk_mq_issue_rq+0x35c/0x6ac [ 39.657037] mmc_mq_queue_rq+0x18c/0x214 [ 39.661022] blk_mq_dispatch_rq_list+0x3a8/0x528 [ 39.665722] __blk_mq_sched_dispatch_requests+0x3a0/0x4ac [ 39.671198] blk_mq_sched_dispatch_requests+0x28/0x5c [ 39.676322] blk_mq_run_hw_queue+0x11c/0x12c [ 39.680668] blk_mq_flush_plug_list+0x200/0x33c [ 39.685278] blk_add_rq_to_plug+0x68/0xd8 [ 39.689365] blk_mq_submit_bio+0x3a4/0x458 [ 39.693539] __submit_bio+0x1c/0x80 [ 39.697096] submit_bio_noacct_nocheck+0x94/0x174 [ 39.701875] submit_bio_noacct+0x1b0/0x22c [ 39.706042] submit_bio+0xac/0xe8 [ 39.709424] blk_next_bio+0x4c/0x5c [ 39.712973] blkdev_issue_secure_erase+0x118/0x170 [ 39.717835] blkdev_common_ioctl+0x374/0x728 [ 39.722175] blkdev_ioctl+0x8c/0x2b0Quoted 8 lines
[ 39.725816] vfs_ioctl+0x24/0x40 [ 39.729117] __arm64_sys_ioctl+0x5c/0x8c [ 39.733114] invoke_syscall+0x68/0xec [ 39.736839] el0_svc_common.constprop.0+0x70/0xd8 [ 39.741609] do_el0_svc+0x18/0x20 [ 39.744981] el0_svc+0x68/0x94 [ 39.748107] el0t_64_sync_handler+0x88/0x124 [ 39.752455] el0t_64_sync+0x168/0x16cThanks for the detailed log!
Quoted 18 lines
Fix skips the
card->busy()and usesMMC_SEND_STATUSandR1_STATUScheck forMMC_ERASE_BUSYbusy_cmdcase in themmc_busy_cb()function.Fixes 0d84c3e6a5b2 ("mmc: core: Convert to mmc_poll_for_busy() for erase/trim/discard")Signed-off-by Kamal Dasu <[email protected]>--- drivers/mmc/core/mmc_ops.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/mmc/core/mmc_ops.c +0
-0@@ -464,7 +464,8 @@ static int mmc_busy_cb(void *cb_data, bool *busy)u32 status =0 ;int err;Quoted 11 lines
Quoted 11 lines
drivers/mmc/core/mmc_ops.c static int mmc_busy_cb(void *cb_data, bool *busy) · line 471
Quoted 6 lines
drivers/mmc/core/mmc_ops.c +2
-1-if (data->busy_cmd !=MMC_BUSY_IO && host->ops->card_busy) { +if (data->busy_cmd !=MMC_BUSY_IO && + data->busy_cmd !=MMC_BUSY_ERASE && host->ops->card_busy) { *busy = host->ops->card_busy (host);return 0 ; }So it seems like the ->card_busy() callback is broken in for your mmc host-driver and platform. Can you perhaps provide the information about what HW/driver you are using?
Using the sdhci-brcmstb driver on a Broadcom Settop based SoC.
Quoted 7 lines
Quoted 7 lines
The point with using the ->card_busy() callback, is to avoid sending the CMD13. Ideally it should be cheaper/faster and in most cases it translates to a read of a register. For larger erases, we would probably end up sending the CMD13 periodically every 32-64 ms, which shouldn't be a problem. However, for smaller erases and discards, we may want the benefit the ->card_busy() callback provides us.
I have tested two scenarios. One is like the mkfs.f2fs app that calls :
ioctl(fd, BLKSECDISCARD, &range);Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
This has the following CMD and completion sequence:
{CMD35->CMD36->CMD38} and poll for DAT0 signal viacard->busy. CMD38 has a response of R1b. The DAT0 (Busy line) will be driven by the device. Busy (DAT0 = 0) is asserted by a device for erasing blocks. Stays busy in brcmstb sdhci controller.How big is the "range"?
The task just blocks here. I have attached the stack.
Quoted 4 lines
Quoted 4 lines
Just so I get this right, it stays busy and we are waiting for the timeout to fire? And ideally you think we should not be busy for that long, right?
The timeout does not fire.
Quoted 10 lines
Quoted 10 lines
Quoted 5 lines
With the additional change followed by CMD13 (response of R1), which returns the device status, the
DAT0 will be pulled-up and next time we read the BUSY status it will indicate it is not busy.So you are referring to read the BUSY status with you ->card_busy() callback? Or did you actually verify that this is true from an electrical point of view, by monitoring the DAT0 signal?
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
If the latter, perhaps it's the card that is failing and simply requires CMD13 to be used to poll for busy. What card is this?
Have you tried different cards with the same platform/driver?
Yes, I have tried Micron and Sandisk 8GB cards with the same platform with the same results.
Okay, so it sounds like it's the ->card_busy() callback that may not work as expected after all.
Do we have an SD card slot on this platform that we can try to run similar tests for but with an SD card instead?
Quoted 26 lines
Quoted 26 lines
Quoted 26 lines
Quoted 6 lines
Also I tried the mmc util and that does not show the same issue with exactly the same ranges, however in that case there are some differences in the way the CMD sequence is sent for the entire discard operation.
Quoted 7 lines
# mmc erase discard 0x000087a4 0x002effff /dev/mmcblk1 /* send erase cmd with multi-cmd */ ret = ioctl(dev_fd, MMC_IOC_MULTI_CMD, multi_cmd);
CMD35->CMD13->CMD36->CMD13->CMD38->CMD13
I do not see any hang in all the erase options discard, legacy, trim, trim2, secure-trim used here with mmc util .So CMD13 seems to do the trick for you. Although, I think we need to figure out if this a special "broken" card or if the problem is with the ->card_busy() implementation for your platform.
Quoted 7 lines
Also looking at JEDEC Standard No. 84-B51 Page 276, 277 "Once the erase groups are selected the host will send an ERASE (CMD38) command. It is recom-
mended that the host terminates the sequence with aSEND_STATUS(CMD13) to poll any additional
status information the Device may have (e.g.,WP_ERASE_SKIP, etc.)."
Quoted 6 lines
Quoted 4 lines
Quoted 3 lines
Isn't that exactly what is being done? After the card has stopped signaling busy, we send a CMD13 in
mmc_busy_cb()to read the additional status information.Yes, that is what the fix does. However in the original if ->card->busy() is being used we do not send the CMD13.
We are not sending CMD13 to poll for busy, but we are indeed sending a CMD13 *after* the card has stopped signal busy, to read the additional status information.
This seems to be according to the spec.
Quoted 11 lines
Quoted 9 lines
Agreed with your interpretation FWIW.
Quoted 5 lines
I don't get it, why should the card stop signal busy, just because we send a CMD13. If so, the card should probably be considered broken. For broken cards, we can try to use a card-quirk instead - to enforce CMD13 polling.
Yes would be one of the solutions that can be considered. Would open to any suggestion on what card-quirk to use.
As you have tested different cards, it's more likely to be a problem with the platform/HW and the ->card_busy() callback.
Quoted 13 lines
Quoted 8 lines
I'll mention it here, I've seen some broken IP out there where the card's FSM (including busy-signalling) was dependent on the host providing the CLK, can't remember which one it was, though.
Anyway for Kamal, it might be interesting to know if your host controller autostops the CLK (which it is allowed to) during the busy-signalling and if not stopping it also works around the problem.The host controller is not stopping the clock. Also stopping the clock does not work around the problem. host is expecting the device FSM pull up the busy line.
At this point I can either do this when adding host:
Review
Quoted 2 lines
(quoted diff) +2
-0+ /* we dont use busy signal */ + host->mmc_host_ops.card_busy = NULL;
Looks like this is the best option, unless we can figure out why the ->card_busy() callback doesn't work as expected.
Quoted 4 lines
Or introduce a card-quirk for this situation.
Kamal
Kind regards
Uffe