Skip to contentSkip to conversation

drm/bridge: adv7511: Fix Intermittent EDID failures

PATCH Superseded Adam Ford 4 participants 5 messages May 21, 2024 – May 22, 2024

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/1 drm/bridge: adv7511: Fix Intermittent EDID failures

In the process of adding support for shared IRQ pins, a scenario was accidentally created where adv7511_irq_process returned prematurely causing the EDID to fail randomly.

Since the interrupt handler is broken up into two main helper functions, update both of them to treat the helper functions as IRQ handlers. These IRQ routines process their respective tasks as before, but if they determine that actual work was done, mark the respective IRQ status accordingly, and delay the check until everything has been processed.

This should guarantee the helper functions don't return prematurely while still returning proper values of either IRQ_HANDLED or IRQ_NONE.

Reported by: Liu Ying <[email protected]>

Fixes f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")
drivers/gpu/drm/bridge/adv7511/adv7511.h +1 -1
index ea271f62b214..ec0b7f3d889c 100644
@@ -401,7 +401,7 @@ struct adv7511 {
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
 int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511);
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
 #else
 static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
 {
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +13 -7
index 44451a9658a3..4efb2cabf1b5 100644
@@ -119,7 +119,7 @@ static void adv7511_cec_rx(struct adv7511 *adv7511, int rx_buf)
 	cec_received_msg(adv7511->cec_adap, &msg);
 }
 
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 {
 	unsigned int offset = adv7511->info->reg_cec_offset;
 	const u32 irq_tx_mask = ADV7511_INT1_CEC_TX_READY |
@@ -130,17 +130,21 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 				ADV7511_INT1_CEC_RX_READY3;
 	unsigned int rx_status;
 	int rx_order[3] = { -1, -1, -1 };
-	int i;
+	int i, ret = 0;
+	int irq_status = IRQ_NONE;
 
-	if (irq1 & irq_tx_mask)
+	if (irq1 & irq_tx_mask) {
 		adv_cec_tx_raw_status(adv7511, irq1);
+		irq_status = IRQ_HANDLED;
+	}
 
 	if (!(irq1 & irq_rx_mask))
-		return;
+		return irq_status;
 
-	if (regmap_read(adv7511->regmap_cec,
-			ADV7511_REG_CEC_RX_STATUS + offset, &rx_status))
-		return;
+	ret = regmap_read(adv7511->regmap_cec,
+			ADV7511_REG_CEC_RX_STATUS + offset, &rx_status);
+	if (ret < 0)
+		return ret;
 
 	/*
 	 * ADV7511_REG_CEC_RX_STATUS[5:0] contains the reception order of RX
@@ -172,6 +176,8 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 
 		adv7511_cec_rx(adv7511, rx_buf);
 	}
+
+	return IRQ_HANDLED;
 }
 
 static int adv7511_cec_adap_enable(struct cec_adapter *adap, bool enable)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +16 -11
index 66ccb61e2a66..56dd2d5a0376 100644
@@ -469,6 +469,8 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 {
 	unsigned int irq0, irq1;
 	int ret;
+	int cec_status;
+	int irq_status = IRQ_NONE;
 
 	ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
 	if (ret < 0)
@@ -478,38 +480,41 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 	if (ret < 0)
 		return ret;
 
-	/* If there is no IRQ to handle, exit indicating no IRQ data */
-	if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
-	    !(irq1 & ADV7511_INT1_DDC_ERROR))
-		return -ENODATA;
-
 	regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
 	regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
 
-	if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
+	if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder) {
 		schedule_work(&adv7511->hpd_work);
+		irq_status = IRQ_HANDLED;
+	}
 
 	if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
 		adv7511->edid_read = true;
 
 		if (adv7511->i2c_main->irq)
 			wake_up_all(&adv7511->wq);
+		irq_status = IRQ_HANDLED;
 	}
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
-	adv7511_cec_irq_process(adv7511, irq1);
+	cec_status = adv7511_cec_irq_process(adv7511, irq1);
+
+	if (cec_status < 0)
+		return cec_status;
 #endif
 
-	return 0;
+	/* If there is no IRQ to handle, exit indicating no IRQ data */
+	if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)
+		return IRQ_HANDLED;
+
+	return IRQ_NONE;
 }
 
 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
 {
 	struct adv7511 *adv7511 = devid;
-	int ret;
 
-	ret = adv7511_irq_process(adv7511, true);
-	return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
+	return adv7511_irq_process(adv7511, true);
 }
 
 /* -----------------------------------------------------------------------------
Signature · 1 line
2.43.0
#1 lore raw
kernel test robot noticed the following build warnings:

Hi Adam,

kernel test robot noticed the following build warnings:

[auto build test WARNING on drm-misc/drm-misc-next]
[also build test WARNING on drm/drm-next drm-exynos/exynos-drm-next drm-intel/for-linux-next drm-tip/drm-tip linus/master drm-intel/for-linux-next-fixes v6.9 next-20240521] [If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Adam-Ford/drm-bridge-adv7511-Fix-Intermittent-EDID-failures/20240521-091841
base:   git://anongit.freedesktop.org/drm/drm-misc drm-misc-next
patch link:    https://lore.kernel.org/r/20240521011614.496421-1-aford173%40gmail.com
patch subject: [PATCH] drm/bridge: adv7511:  Fix Intermittent EDID failures
config: i386-buildonly-randconfig-002-20240521 (https://download.01.org/0day-ci/archive/20240522/[email protected]/config)
compiler: clang version 18.1.5 (https://github.com/llvm/llvm-project 617a15a9eac96088ae5e9134248d8236e34b91b1)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240522/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All warnings (new ones prefixed by >>):

>> drivers/gpu/drm/bridge/adv7511/adv7511_drv.c:507:35: warning: variable 'cec_status' is uninitialized when used here [-Wuninitialized]
     507 |         if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)
         |                                          ^~~~~~~~~~
   drivers/gpu/drm/bridge/adv7511/adv7511_drv.c:472:16: note: initialize the variable 'cec_status' to silence this warning
     472 |         int cec_status;
         |                       ^
         |                        = 0

1 warning generated.

vim +/cec_status +507 drivers/gpu/drm/bridge/adv7511/adv7511_drv.c

505
506 /* If there is no IRQ to handle, exit indicating no IRQ data */

 > 507		if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)

508 return IRQ_HANDLED;
509
510 return IRQ_NONE;
511 }
512

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
author
#2 lore raw
In reply to Adam Ford
Quoted 11 lines · Adam Ford

In the process of adding support for shared IRQ pins, a scenario was accidentally created where adv7511_irq_process returned prematurely causing the EDID to fail randomly.

Since the interrupt handler is broken up into two main helper functions, update both of them to treat the helper functions as IRQ handlers. These IRQ routines process their respective tasks as before, but if they determine that actual work was done, mark the respective IRQ status accordingly, and delay the check until everything has been processed.

Quoted 6 lines

This should guarantee the helper functions don't return prematurely while still returning proper values of either IRQ_HANDLED or IRQ_NONE.

Reported by: Liu Ying <[email protected]>

Fixes f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")

+ Liu

Sorry about the e-mail address copy-paste error.

Quoted 133 lines
drivers/gpu/drm/bridge/adv7511/adv7511.h +1 -1
index ea271f62b214..ec0b7f3d889c 100644
@@ -401,7 +401,7 @@ struct adv7511 {
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
 int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511);
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
 #else
 static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
 {
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +13 -7
index 44451a9658a3..4efb2cabf1b5 100644
@@ -119,7 +119,7 @@ static void adv7511_cec_rx(struct adv7511 *adv7511, int rx_buf)
        cec_received_msg(adv7511->cec_adap, &msg);
 }
 
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 {
        unsigned int offset = adv7511->info->reg_cec_offset;
        const u32 irq_tx_mask = ADV7511_INT1_CEC_TX_READY |
@@ -130,17 +130,21 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
                                ADV7511_INT1_CEC_RX_READY3;
        unsigned int rx_status;
        int rx_order[3] = { -1, -1, -1 };
-       int i;
+       int i, ret = 0;
+       int irq_status = IRQ_NONE;
 
-       if (irq1 & irq_tx_mask)
+       if (irq1 & irq_tx_mask) {
                adv_cec_tx_raw_status(adv7511, irq1);
+               irq_status = IRQ_HANDLED;
+       }
 
        if (!(irq1 & irq_rx_mask))
-               return;
+               return irq_status;
 
-       if (regmap_read(adv7511->regmap_cec,
-                       ADV7511_REG_CEC_RX_STATUS + offset, &rx_status))
-               return;
+       ret = regmap_read(adv7511->regmap_cec,
+                       ADV7511_REG_CEC_RX_STATUS + offset, &rx_status);
+       if (ret < 0)
+               return ret;
 
        /*
         * ADV7511_REG_CEC_RX_STATUS[5:0] contains the reception order of RX
@@ -172,6 +176,8 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 
                adv7511_cec_rx(adv7511, rx_buf);
        }
+
+       return IRQ_HANDLED;
 }
 
 static int adv7511_cec_adap_enable(struct cec_adapter *adap, bool enable)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +16 -12
index 66ccb61e2a66..56dd2d5a0376 100644
@@ -469,6 +469,8 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 {
        unsigned int irq0, irq1;
        int ret;
+       int cec_status;
+       int irq_status = IRQ_NONE;
 
        ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
        if (ret < 0)
@@ -478,38 +480,41 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
        if (ret < 0)
                return ret;
 
-       /* If there is no IRQ to handle, exit indicating no IRQ data */
-       if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
-           !(irq1 & ADV7511_INT1_DDC_ERROR))
-               return -ENODATA;
-
        regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
        regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
 
-       if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
+       if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder) {
                schedule_work(&adv7511->hpd_work);
+               irq_status = IRQ_HANDLED;
+       }
 
        if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
                adv7511->edid_read = true;
 
                if (adv7511->i2c_main->irq)
                        wake_up_all(&adv7511->wq);
+               irq_status = IRQ_HANDLED;
        }
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
-       adv7511_cec_irq_process(adv7511, irq1);
+       cec_status = adv7511_cec_irq_process(adv7511, irq1);
+
+       if (cec_status < 0)
+               return cec_status;
 #endif
 
-       return 0;
+       /* If there is no IRQ to handle, exit indicating no IRQ data */
+       if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)
+               return IRQ_HANDLED;
+
+       return IRQ_NONE;
 }
 
 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
 {
        struct adv7511 *adv7511 = devid;
-       int ret;
 
-       ret = adv7511_irq_process(adv7511, true);
-       return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
+       return adv7511_irq_process(adv7511, true);
 }
 
 /* -----------------------------------------------------------------------------
--

2.43.0

Tested-by
#3 lore raw
Quoted 12 lines · Adam Ford
Quoted 11 lines · Adam Ford

In the process of adding support for shared IRQ pins, a scenario was accidentally created where adv7511_irq_process returned prematurely causing the EDID to fail randomly.

Since the interrupt handler is broken up into two main helper functions, update both of them to treat the helper functions as IRQ handlers. These IRQ routines process their respective tasks as before, but if they determine that actual work was done, mark the respective IRQ status accordingly, and delay the check until everything has been processed.

Quoted 4 lines
Quoted 4 lines

This should guarantee the helper functions don't return prematurely while still returning proper values of either IRQ_HANDLED or IRQ_NONE.

Reported by: Liu Ying <[email protected]>

s/Reported by/Reported-by/

Quoted 6 lines
Quoted 2 lines
Fixes f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")

+ Liu

Sorry about the e-mail address copy-paste error.

No worries.

With this patch, it looks EDID retrieval works ok for me without interrupt requested.

Quoted 133 lines
Quoted 133 lines
drivers/gpu/drm/bridge/adv7511/adv7511.h +1 -1
index ea271f62b214..ec0b7f3d889c 100644
@@ -401,7 +401,7 @@ struct adv7511 {
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
 int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511);
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
 #else
 static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
 {
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +13 -7
index 44451a9658a3..4efb2cabf1b5 100644
@@ -119,7 +119,7 @@ static void adv7511_cec_rx(struct adv7511 *adv7511, int rx_buf)
        cec_received_msg(adv7511->cec_adap, &msg);
 }
 
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 {
        unsigned int offset = adv7511->info->reg_cec_offset;
        const u32 irq_tx_mask = ADV7511_INT1_CEC_TX_READY |
@@ -130,17 +130,21 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
                                ADV7511_INT1_CEC_RX_READY3;
        unsigned int rx_status;
        int rx_order[3] = { -1, -1, -1 };
-       int i;
+       int i, ret = 0;
+       int irq_status = IRQ_NONE;
 
-       if (irq1 & irq_tx_mask)
+       if (irq1 & irq_tx_mask) {
                adv_cec_tx_raw_status(adv7511, irq1);
+               irq_status = IRQ_HANDLED;
+       }
 
        if (!(irq1 & irq_rx_mask))
-               return;
+               return irq_status;
 
-       if (regmap_read(adv7511->regmap_cec,
-                       ADV7511_REG_CEC_RX_STATUS + offset, &rx_status))
-               return;
+       ret = regmap_read(adv7511->regmap_cec,
+                       ADV7511_REG_CEC_RX_STATUS + offset, &rx_status);
+       if (ret < 0)
+               return ret;
 
        /*
         * ADV7511_REG_CEC_RX_STATUS[5:0] contains the reception order of RX
@@ -172,6 +176,8 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 
                adv7511_cec_rx(adv7511, rx_buf);
        }
+
+       return IRQ_HANDLED;
 }
 
 static int adv7511_cec_adap_enable(struct cec_adapter *adap, bool enable)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +16 -12
index 66ccb61e2a66..56dd2d5a0376 100644
@@ -469,6 +469,8 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 {
        unsigned int irq0, irq1;
        int ret;
+       int cec_status;
+       int irq_status = IRQ_NONE;
 
        ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
        if (ret < 0)
@@ -478,38 +480,41 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
        if (ret < 0)
                return ret;
 
-       /* If there is no IRQ to handle, exit indicating no IRQ data */
-       if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
-           !(irq1 & ADV7511_INT1_DDC_ERROR))
-               return -ENODATA;
-
        regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
        regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
 
-       if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
+       if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder) {
                schedule_work(&adv7511->hpd_work);
+               irq_status = IRQ_HANDLED;
+       }
 
        if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
                adv7511->edid_read = true;
 
                if (adv7511->i2c_main->irq)
                        wake_up_all(&adv7511->wq);
+               irq_status = IRQ_HANDLED;
        }
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
-       adv7511_cec_irq_process(adv7511, irq1);
+       cec_status = adv7511_cec_irq_process(adv7511, irq1);
+
+       if (cec_status < 0)
+               return cec_status;
 #endif
 
-       return 0;
+       /* If there is no IRQ to handle, exit indicating no IRQ data */
+       if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)
+               return IRQ_HANDLED;
+
+       return IRQ_NONE;
 }
 
 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
 {
        struct adv7511 *adv7511 = devid;
-       int ret;
 
-       ret = adv7511_irq_process(adv7511, true);
-       return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
+       return adv7511_irq_process(adv7511, true);
 }
 
 /* -----------------------------------------------------------------------------
--

2.43.0

#4 lore raw
In reply to Adam Ford
Quoted 58 lines · Adam Ford

In the process of adding support for shared IRQ pins, a scenario was accidentally created where adv7511_irq_process returned prematurely causing the EDID to fail randomly.

Since the interrupt handler is broken up into two main helper functions, update both of them to treat the helper functions as IRQ handlers. These IRQ routines process their respective tasks as before, but if they determine that actual work was done, mark the respective IRQ status accordingly, and delay the check until everything has been processed.

This should guarantee the helper functions don't return prematurely while still returning proper values of either IRQ_HANDLED or IRQ_NONE.

Reported by: Liu Ying <[email protected]>

Fixes f3d9683346d6 ("drm/bridge: adv7511: Allow IRQ to share GPIO pins")
drivers/gpu/drm/bridge/adv7511/adv7511.h +1 -1
index ea271f62b214..ec0b7f3d889c 100644
@@ -401,7 +401,7 @@ struct adv7511 {
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
 int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511);
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1);
 #else
 static inline int adv7511_cec_init(struct device *dev, struct adv7511 *adv7511)
 {
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +6 -3
index 44451a9658a3..4efb2cabf1b5 100644
@@ -119,7 +119,7 @@ static void adv7511_cec_rx(struct adv7511 *adv7511, int rx_buf)
 	cec_received_msg(adv7511->cec_adap, &msg);
 }
 
-void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
+int adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 {
 	unsigned int offset = adv7511->info->reg_cec_offset;
 	const u32 irq_tx_mask = ADV7511_INT1_CEC_TX_READY |
@@ -130,17 +130,21 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 				ADV7511_INT1_CEC_RX_READY3;
 	unsigned int rx_status;
 	int rx_order[3] = { -1, -1, -1 };
-	int i;
+	int i, ret = 0;
+	int irq_status = IRQ_NONE;
 
-	if (irq1 & irq_tx_mask)
+	if (irq1 & irq_tx_mask) {
 		adv_cec_tx_raw_status(adv7511, irq1);
+		irq_status = IRQ_HANDLED;
+	}
 
 	if (!(irq1 & irq_rx_mask))

drivers/gpu/drm/bridge/adv7511/adv7511_cec.c void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1) · line 147

Quoted 10 lines
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +5 -4
-		return;
+		return irq_status;
 
-	if (regmap_read(adv7511->regmap_cec,
-			ADV7511_REG_CEC_RX_STATUS + offset, &rx_status))
-		return;
+	ret = regmap_read(adv7511->regmap_cec,
+			ADV7511_REG_CEC_RX_STATUS + offset, &rx_status);
+	if (ret < 0)
+		return ret;

Ok, maybe I was wrong with my previous suggestion. The code starts to look more and more clumsy. Do we really care about error status at all? Maybe it's enough to return IRQ_NONE here from the IRQ handlers?

Quoted 17 lines
drivers/gpu/drm/bridge/adv7511/adv7511_cec.c +2 -0
 	/*
 	 * ADV7511_REG_CEC_RX_STATUS[5:0] contains the reception order of RX
@@ -172,6 +176,8 @@ void adv7511_cec_irq_process(struct adv7511 *adv7511, unsigned int irq1)
 
 		adv7511_cec_rx(adv7511, rx_buf);
 	}
+
+	return IRQ_HANDLED;
 }
 
 static int adv7511_cec_adap_enable(struct cec_adapter *adap, bool enable)
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +0 -0
index 66ccb61e2a66..56dd2d5a0376 100644

drivers/gpu/drm/bridge/adv7511/adv7511_drv.c static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd) · line 472

Quoted 4 lines
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +1 -0
@@ -469,6 +469,8 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 {
 	unsigned int irq0, irq1;
 	int ret;
+	int cec_status;

cec_status ends up being unset if CEC is disabled.

Quoted 44 lines
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +14 -8
+	int irq_status = IRQ_NONE;
 
 	ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
 	if (ret < 0)
@@ -478,38 +480,41 @@ static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 	if (ret < 0)
 		return ret;
 
-	/* If there is no IRQ to handle, exit indicating no IRQ data */
-	if (!(irq0 & (ADV7511_INT0_HPD | ADV7511_INT0_EDID_READY)) &&
-	    !(irq1 & ADV7511_INT1_DDC_ERROR))
-		return -ENODATA;
-
 	regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
 	regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
 
-	if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
+	if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder) {
 		schedule_work(&adv7511->hpd_work);
+		irq_status = IRQ_HANDLED;
+	}
 
 	if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
 		adv7511->edid_read = true;
 
 		if (adv7511->i2c_main->irq)
 			wake_up_all(&adv7511->wq);
+		irq_status = IRQ_HANDLED;
 	}
 
 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
-	adv7511_cec_irq_process(adv7511, irq1);
+	cec_status = adv7511_cec_irq_process(adv7511, irq1);
+
+	if (cec_status < 0)
+		return cec_status;
 #endif
 
-	return 0;
+	/* If there is no IRQ to handle, exit indicating no IRQ data */
+	if (irq_status == IRQ_HANDLED || cec_status == IRQ_HANDLED)
+		return IRQ_HANDLED;
+
+	return IRQ_NONE;

drivers/gpu/drm/bridge/adv7511/adv7511_drv.c static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd) · line 517

Quoted 10 lines
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +1 -3
 }
 
 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
 {
 	struct adv7511 *adv7511 = devid;
-	int ret;
 
-	ret = adv7511_irq_process(adv7511, true);
-	return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
+	return adv7511_irq_process(adv7511, true);

This should be return ret < 0 ? IRQ_NONE : ret. We should not be returning negative error via irqreturn_t.

Quoted 6 lines
drivers/gpu/drm/bridge/adv7511/adv7511_drv.c +0 -0
 }
 
 /* -----------------------------------------------------------------------------
Signature · 1 line
2.43.0
Signature · 2 lines
With best wishes
Dmitry