Skip to contentSkip to conversation

support AST2700 network

PATCH Applied Jamin Lin via 3 participants 17 messages Jul 4, 2024 – Jul 9, 2024 Arm/Aspeed machine support

lore
Share & tools
lore
#0 lore raw

v3 cover support AST2700 network

change from v1:
- ftgmac100
- fix coding style
- support 64 bits dma dram address for AST2700

change from v2:
- ftgmac100: update memory region size to 0x200.
- ftgmac100: introduce a new class(ftgmac100_high),
class attribute and memop handlers, for FTGMAC100_*_HIGH regs read/write.
- aspeed_ast27x0: update network model to ftgmac100_high to support 64 bits dram address DMA.
- m25p80: support quad mode for w25q01jvq

change from v3:
- ftgmac100: update memory region size to 64KB.
- ftgmac100: using a property to activate the region for new registers, instead of a class
- ftgmac100: introduce TX and RX ring base address high registers
- ftgmac100: split standalone patch for easy review
- ftgmac100: update TX and RX packet buffers address to 64 bits
- aspeed_ast27x0: set dma64 property for AST2700 ftgmac100
- machine_aspeed.py: update to test sdk v09.02 and network for AST2700

Jamin Lin (8):
hw/net:ftgmac100: update memory region size to 64KB hw/net:ftgmac100: update ring base address to 64 bits hw/net:ftgmac100: introduce TX and RX ring base address high registers
to support 64 bits
hw/net:ftgmac100: update TX and RX packet buffers address to 64 bits aspeed/soc: set dma64 property for AST2700 ftgmac100 hw/block: m25p80: support quad mode for w25q01jvq machine_aspeed.py: update to test ASPEED OpenBMC SDK v09.02 for

    AST2700

machine_aspeed.py: update to test network for AST2700

 hw/arm/aspeed_ast27x0.c         |   3 +
 hw/block/m25p80.c               |  16 ++++
 hw/net/ftgmac100.c              | 147 +++++++++++++++++++++++++++-----
 include/hw/net/ftgmac100.h      |  17 ++--
 tests/avocado/machine_aspeed.py |  12 +--
 5 files changed, 162 insertions(+), 33 deletions(-)
Signature · 1 line
2.34.1
#1 lore raw

PATCH v3 1/8 hw/net:ftgmac100: update memory region size to 64KB

According to the datasheet of ASPEED SOCs,
one MAC controller owns 128KB of register space for AST2500. However, one MAC controller only owns 64KB of register space for AST2600 and AST2700. It set the memory region size 128KB and it occupied another controllers Address Spaces.

Update one MAC controller memory region size to 0x1000 because AST2500 did not use register spaces over than 64KB.

Introduce a new container region size to 0x1000 and its range is from 0 to 0xfff. This container is mapped a sub region for the current set of register.
This sub region range is from 0 to 0xff.

---
 hw/net/ftgmac100.c         | 11 ++++++++---
 include/hw/net/ftgmac100.h |  4 ++++
 2 files changed, 12 insertions(+), 3 deletions(-)
hw/net/ftgmac100.c +8 -3
index 25e4c0cd5b..9e1f12cd33 100644
@@ -1107,9 +1107,14 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
         s->rxdes0_edorr = FTGMAC100_RXDES0_EDORR;
     }
 
-    memory_region_init_io(&s->iomem, OBJECT(dev), &ftgmac100_ops, s,
-                          TYPE_FTGMAC100, 0x2000);
-    sysbus_init_mmio(sbd, &s->iomem);
+    memory_region_init(&s->iomem_container, OBJECT(s),
+                       TYPE_FTGMAC100 ".container", FTGMAC100_MEM_SIZE);
+    sysbus_init_mmio(sbd, &s->iomem_container);
+
+    memory_region_init_io(&s->iomem, OBJECT(s), &ftgmac100_ops, s,
+                          TYPE_FTGMAC100 ".regs", FTGMAC100_REG_MEM_SIZE);
+    memory_region_add_subregion(&s->iomem_container, 0x0, &s->iomem);
+
     sysbus_init_irq(sbd, &s->irq);
     qemu_macaddr_default_if_unset(&s->conf.macaddr);
 
include/hw/net/ftgmac100.h +4 -0
index 765d1538a4..269446e858 100644
@@ -14,6 +14,9 @@
 #define TYPE_FTGMAC100 "ftgmac100"
 OBJECT_DECLARE_SIMPLE_TYPE(FTGMAC100State, FTGMAC100)
 
+#define FTGMAC100_MEM_SIZE 0x1000
+#define FTGMAC100_REG_MEM_SIZE 0x100
+
 #include "hw/sysbus.h"
 #include "net/net.h"
 
@@ -30,6 +33,7 @@ struct FTGMAC100State {
     NICState *nic;
     NICConf conf;
     qemu_irq irq;
+    MemoryRegion iomem_container;
     MemoryRegion iomem;
 
     uint8_t frame[FTGMAC100_MAX_FRAME_SIZE];
Signature · 1 line
2.34.1
#3 lore raw

PATCH v3 7/8 machine_aspeed.py: update to test ASPEED OpenBMC SDK v09.02 for AST2700

In reply to Jamin Lin via

Update test case to test ASPEED OpenBMC SDK v09.02 for AST2700.

ASPEED fixed TX mask issue from linux/drivers/ftgmac100.c. It is required to use ASPEED OpenBMC SDK since v09.02 for AST2700 QEMU network testing.

A test image is downloaded from the ASPEED Forked OpenBMC GitHub release repository :
https://github.com/AspeedTech-BMC/openbmc/releases/

---
 tests/avocado/machine_aspeed.py | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
tests/avocado/machine_aspeed.py +3 -3
index 3a20644fb2..13fe128fc9 100644
@@ -387,15 +387,15 @@ def test_arm_ast2600_evb_sdk(self):
         year = time.strftime("%Y")
         self.ssh_command_output_contains('/sbin/hwclock -f /dev/rtc1', year);
 
-    def test_aarch64_ast2700_evb_sdk_v09_01(self):
+    def test_aarch64_ast2700_evb_sdk_v09_02(self):
         """
         :avocado: tags=arch:aarch64
         :avocado: tags=machine:ast2700-evb
         """
 
         image_url = ('https://github.com/AspeedTech-BMC/openbmc/releases/'
-                     'download/v09.01/ast2700-default-obmc.tar.gz')
-        image_hash = 'b1cc0fd73c7650d34c9c8459a243f52a91e9e27144b8608b2645ab19461d1e07'
+                     'download/v09.02/ast2700-default-obmc.tar.gz')
+        image_hash = 'ac969c2602f4e6bdb69562ff466b89ae3fe1d86e1f6797bb7969d787f82116a7'
         image_path = self.fetch_asset(image_url, asset_hash=image_hash,
                                       algorithm='sha256')
         archive.extract(image_path, self.workdir)
Signature · 1 line
2.34.1
#9 lore raw

PATCH v3 4/8 hw/net:ftgmac100: update TX and RX packet buffers address to 64 bits

In reply to Jamin Lin via

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

It have "TXDES 2" and "RXDES 2" to save the high part physical address of packet buffer.
Ex: TX packet buffer address [34:0]
The "TXDES 2" bits [18:16] which corresponds the bits [34:32] of the 64 bits address of the TX packet buffer address and "TXDES 3" bits [31:0] which corresponds the bits [31:0] of the 64 bits address of the TX packet buffer address.

Update TX and RX packet buffers address type to
64 bits for dram 64 bits address DMA support.

---
 hw/net/ftgmac100.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)
hw/net/ftgmac100.c +18 -3
index 68956aeb94..80f9cd56d5 100644
@@ -175,6 +175,8 @@
 #define FTGMAC100_TXDES1_TX2FIC          (1 << 30)
 #define FTGMAC100_TXDES1_TXIC            (1 << 31)
 
+#define FTGMAC100_TXDES2_TXBUF_BADR_HI(x)   (((x) >> 16) & 0x7)
+
 /*
  * Receive descriptor
  */
@@ -208,13 +210,15 @@
 #define FTGMAC100_RXDES1_UDP_CHKSUM_ERR  (1 << 26)
 #define FTGMAC100_RXDES1_IP_CHKSUM_ERR   (1 << 27)
 
+#define FTGMAC100_RXDES2_RXBUF_BADR_HI(x)   (((x) >> 16) & 0x7)
+
 /*
  * Receive and transmit Buffer Descriptor
  */
 typedef struct {
     uint32_t        des0;
     uint32_t        des1;
-    uint32_t        des2;        /* not used by HW */
+    uint32_t        des2;        /* used by HW 64 bits DMA */
     uint32_t        des3;
 } FTGMAC100Desc;
 
@@ -531,6 +535,7 @@ static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
     int frame_size = 0;
     uint8_t *ptr = s->frame;
     uint64_t addr = tx_descriptor;
+    uint64_t buf_addr = 0;
     uint32_t flags = 0;
 
     while (1) {
@@ -569,7 +574,12 @@ static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
             len =  sizeof(s->frame) - frame_size;
         }
 
-        if (dma_memory_read(&address_space_memory, bd.des3,
+        buf_addr = bd.des3;
+        if (s->dma64) {
+            buf_addr = deposit64(buf_addr, 32, 32,
+                                 FTGMAC100_TXDES2_TXBUF_BADR_HI(bd.des2));
+        }
+        if (dma_memory_read(&address_space_memory, buf_addr,
                             ptr, len, MEMTXATTRS_UNSPECIFIED)) {
             qemu_log_mask(LOG_GUEST_ERROR, "%s: failed to read packet @ 0x%x\n",
                           __func__, bd.des3);
@@ -1022,7 +1032,7 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
     uint32_t flags = 0;
     uint64_t addr;
     uint32_t crc;
-    uint32_t buf_addr;
+    uint64_t buf_addr = 0;
     uint8_t *crc_ptr;
     uint32_t buf_len;
     size_t size = len;
@@ -1087,7 +1097,12 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
         if (size < 4) {
             buf_len += size - 4;
         }
+
         buf_addr = bd.des3;
+        if (s->dma64) {
+            buf_addr = deposit64(buf_addr, 32, 32,
+                                 FTGMAC100_RXDES2_RXBUF_BADR_HI(bd.des2));
+        }
         if (first && proto == ETH_P_VLAN && buf_len >= 18) {
             bd.des1 = lduw_be_p(buf + 14) | FTGMAC100_RXDES1_VLANTAG_AVAIL;
 
Signature · 1 line
2.34.1
#13 lore raw

PATCH v3 5/8 aspeed/soc: set dma64 property for AST2700 ftgmac100

In reply to Jamin Lin via

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

Set dma64 property for ftgmac100 model to support
64bits dram address DMA.

---
 hw/arm/aspeed_ast27x0.c | 3 +++
 1 file changed, 3 insertions(+)
hw/arm/aspeed_ast27x0.c +3 -0
index 18e6a8b10c..a9fb0d4b88 100644
@@ -552,9 +552,12 @@ static void aspeed_soc_ast2700_realize(DeviceState *dev, Error **errp)
         return;
     }
 
+    /* Net */
     for (i = 0; i < sc->macs_num; i++) {
         object_property_set_bool(OBJECT(&s->ftgmac100[i]), "aspeed", true,
                                  &error_abort);
+        object_property_set_bool(OBJECT(&s->ftgmac100[i]), "dma64", true,
+                                 &error_abort);
         if (!sysbus_realize(SYS_BUS_DEVICE(&s->ftgmac100[i]), errp)) {
             return;
         }
Signature · 1 line
2.34.1
#7 lore raw

PATCH v3 3/8 hw/net:ftgmac100: introduce TX and RX ring base address high registers to support 64 bits

In reply to Jamin Lin via

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

It have "Normal Priority Transmit Ring Base Address Register High(0x17C)", "High Priority Transmit Ring Base Address Register High(0x184)" and "Receive Ring Base Address Register High(0x18C)" to save the high part physical address of descriptor manager.
Ex: TX descriptor manager address [34:0]
The "Normal Priority Transmit Ring Base Address Register High(0x17C)" bits [2:0] which corresponds the bits [34:32] of the 64 bits address of the TX ring buffer address.
The "Normal Priority Transmit Ring Base Address Register(0x20)" bits [31:0] which corresponds the bits [31:0] of the 64 bits address
of the TX ring buffer address.

Introduce a new sub region which size is 0x100 for the set of new registers and map it at 0x100 in the container region.
This sub region range is from 0x100 to 0x1ff.

Introduce a new property and object attribute to activate the region for new registers. Introduce a new memop handlers for the new register read and write.

---
 hw/net/ftgmac100.c         | 82 ++++++++++++++++++++++++++++++++++++++
 include/hw/net/ftgmac100.h |  4 ++
 2 files changed, 86 insertions(+)
hw/net/ftgmac100.c +82 -0
index d026242e2b..68956aeb94 100644
@@ -56,6 +56,16 @@
 #define FTGMAC100_PHYDATA         0x64
 #define FTGMAC100_FCR             0x68
 
+/*
+ * FTGMAC100 registers high
+ *
+ * values below are offset by - FTGMAC100_REG_HIGH_OFFSET from datasheet
+ * because its memory region is start at FTGMAC100_REG_HIGH_OFFSET
+ */
+#define FTGMAC100_NPTXR_BADR_HIGH   (0x17C - FTGMAC100_REG_HIGH_OFFSET)
+#define FTGMAC100_HPTXR_BADR_HIGH   (0x184 - FTGMAC100_REG_HIGH_OFFSET)
+#define FTGMAC100_RXR_BADR_HIGH     (0x18C - FTGMAC100_REG_HIGH_OFFSET)
+
 /*
  * Interrupt status register & interrupt enable register
  */
@@ -913,6 +923,60 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
     ftgmac100_update_irq(s);
 }
 
+static uint64_t ftgmac100_high_read(void *opaque, hwaddr addr, unsigned size)
+{
+    FTGMAC100State *s = FTGMAC100(opaque);
+    uint64_t val = 0;
+
+    switch (addr) {
+    case FTGMAC100_NPTXR_BADR_HIGH:
+        val = extract64(s->tx_ring, 32, 32);
+        break;
+    case FTGMAC100_HPTXR_BADR_HIGH:
+        /* High Priority Transmit Ring Base High Address */
+        qemu_log_mask(LOG_UNIMP, "%s: read to unimplemented register 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    case FTGMAC100_RXR_BADR_HIGH:
+        val = extract64(s->rx_ring, 32, 32);
+        break;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad address at offset 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    }
+
+    return val;
+}
+
+static void ftgmac100_high_write(void *opaque, hwaddr addr,
+                          uint64_t value, unsigned size)
+{
+    FTGMAC100State *s = FTGMAC100(opaque);
+
+    switch (addr) {
+    case FTGMAC100_NPTXR_BADR_HIGH:
+        s->tx_ring = deposit64(s->tx_ring, 32, 32, value);
+        s->tx_descriptor = deposit64(s->tx_descriptor, 32, 32, value);
+        break;
+    case FTGMAC100_HPTXR_BADR_HIGH:
+        /* High Priority Transmit Ring Base High Address */
+        qemu_log_mask(LOG_UNIMP, "%s: write to unimplemented register 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    case FTGMAC100_RXR_BADR_HIGH:
+        s->rx_ring = deposit64(s->rx_ring, 32, 32, value);
+        s->rx_descriptor = deposit64(s->rx_descriptor, 32, 32, value);
+        break;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad address at offset 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    }
+
+    ftgmac100_update_irq(s);
+}
+
 static int ftgmac100_filter(FTGMAC100State *s, const uint8_t *buf, size_t len)
 {
     unsigned mcast_idx;
@@ -1077,6 +1141,14 @@ static const MemoryRegionOps ftgmac100_ops = {
     .endianness = DEVICE_LITTLE_ENDIAN,
 };
 
+static const MemoryRegionOps ftgmac100_high_ops = {
+    .read = ftgmac100_high_read,
+    .write = ftgmac100_high_write,
+    .valid.min_access_size = 4,
+    .valid.max_access_size = 4,
+    .endianness = DEVICE_LITTLE_ENDIAN,
+};
+
 static void ftgmac100_cleanup(NetClientState *nc)
 {
     FTGMAC100State *s = FTGMAC100(qemu_get_nic_opaque(nc));
@@ -1114,6 +1186,15 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
                           TYPE_FTGMAC100 ".regs", FTGMAC100_REG_MEM_SIZE);
     memory_region_add_subregion(&s->iomem_container, 0x0, &s->iomem);
 
+    if (s->dma64) {
+        memory_region_init_io(&s->iomem_high, OBJECT(s), &ftgmac100_high_ops,
+                              s, TYPE_FTGMAC100 ".regs.high",
+                              FTGMAC100_REG_HIGH_MEM_SIZE);
+        memory_region_add_subregion(&s->iomem_container,
+                                    FTGMAC100_REG_HIGH_OFFSET,
+                                    &s->iomem_high);
+    }
+
     sysbus_init_irq(sbd, &s->irq);
     qemu_macaddr_default_if_unset(&s->conf.macaddr);
 
@@ -1162,6 +1243,7 @@ static const VMStateDescription vmstate_ftgmac100 = {
 static Property ftgmac100_properties[] = {
     DEFINE_PROP_BOOL("aspeed", FTGMAC100State, aspeed, false),
     DEFINE_NIC_PROPERTIES(FTGMAC100State, conf),
+    DEFINE_PROP_BOOL("dma64", FTGMAC100State, dma64, false),
     DEFINE_PROP_END_OF_LIST(),
 };
 
include/hw/net/ftgmac100.h +4 -0
index aae57ae8cb..24ccdf0260 100644
@@ -16,6 +16,8 @@ OBJECT_DECLARE_SIMPLE_TYPE(FTGMAC100State, FTGMAC100)
 
 #define FTGMAC100_MEM_SIZE 0x1000
 #define FTGMAC100_REG_MEM_SIZE 0x100
+#define FTGMAC100_REG_HIGH_MEM_SIZE 0x100
+#define FTGMAC100_REG_HIGH_OFFSET 0x100
 
 #include "hw/sysbus.h"
 #include "net/net.h"
@@ -35,6 +37,7 @@ struct FTGMAC100State {
     qemu_irq irq;
     MemoryRegion iomem_container;
     MemoryRegion iomem;
+    MemoryRegion iomem_high;
 
     uint8_t frame[FTGMAC100_MAX_FRAME_SIZE];
 
@@ -68,6 +71,7 @@ struct FTGMAC100State {
     bool aspeed;
     uint32_t txdes0_edotr;
     uint32_t rxdes0_edorr;
+    bool dma64;
 };
 
 #define TYPE_ASPEED_MII "aspeed-mmi"
Signature · 1 line
2.34.1
#11 lore raw

PATCH v3 8/8 machine_aspeed.py: update to test network for AST2700

In reply to Jamin Lin via

Update test case to test network connection via SSH.

Test command:

```
cd build
pyvenv/bin/avocado run ../qemu/tests/avocado/machine_aspeed.py:AST2x00MachineSDK.test_aarch64_ast2700_evb_sdk_v09_02
```
---
 tests/avocado/machine_aspeed.py | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
tests/avocado/machine_aspeed.py +4 -2
index 13fe128fc9..f66ad38d35 100644
@@ -313,14 +313,14 @@ def do_test_arm_aspeed_sdk_start(self, image):
 
     def do_test_aarch64_aspeed_sdk_start(self, image):
         self.vm.set_console()
-        self.vm.add_args('-drive', 'file=' + image + ',if=mtd,format=raw')
+        self.vm.add_args('-drive', 'file=' + image + ',if=mtd,format=raw',
+                         '-net', 'nic', '-net', 'user,hostfwd=:127.0.0.1:0-:22')
 
         self.vm.launch()
 
         self.wait_for_console_pattern('U-Boot 2023.10')
         self.wait_for_console_pattern('## Loading kernel from FIT Image')
         self.wait_for_console_pattern('Starting kernel ...')
-        self.wait_for_console_pattern("systemd[1]: Hostname set to")
 
     @skipUnless(os.getenv('QEMU_TEST_FLAKY_TESTS'), 'Test is unstable on GitLab')
 
@@ -436,4 +436,6 @@ def test_aarch64_ast2700_evb_sdk_v09_02(self):
 
         self.vm.add_args('-smp', str(num_cpu))
         self.do_test_aarch64_aspeed_sdk_start(image_dir + 'image-bmc')
+        self.wait_for_console_pattern('nodistro.0 ast2700-default ttyS12')
+        self.ssh_connect('root', '0penBmc', False)
 
Signature · 1 line
2.34.1
#15 lore raw

PATCH v3 6/8 hw/block: m25p80: support quad mode for w25q01jvq

In reply to Jamin Lin via

According to the w25q01jv datasheet at page 16,
it is required to set QE bit in "Status Register 2". Besides, users are able to utilize "Write Status Register 1(0x01)" command to set QE bit in "Status Register 2" and
utilize "Read Status Register 2(0x35)" command to get the QE bit status.

To support quad mode for w25q01jvq, update collecting data needed 2 bytes for WRSR command in decode_new_cmd function and verify QE bit at the second byte of collecting data bit 2 in complete_collecting_data.

Update RDCR_EQIO command to set bit 2 of return data if quad mode enable in decode_new_cmd.

---
 hw/block/m25p80.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
hw/block/m25p80.c +16 -0
index 8dec134832..9e99107b42 100644
@@ -416,6 +416,7 @@ typedef enum {
     /*
      * Micron: 0x35 - enable QPI
      * Spansion: 0x35 - read control register
+     * Winbond: 0x35 - quad enable
      */
     RDCR_EQIO = 0x35,
     RSTQIO = 0xf5,
@@ -798,6 +799,11 @@ static void complete_collecting_data(Flash *s)
                 s->four_bytes_address_mode = extract32(s->data[1], 5, 1);
             }
             break;
+        case MAN_WINBOND:
+            if (s->len > 1) {
+                s->quad_enable = !!(s->data[1] & 0x02);
+            }
+            break;
         default:
             break;
         }
@@ -1254,6 +1260,10 @@ static void decode_new_cmd(Flash *s, uint32_t value)
             s->needed_bytes = 2;
             s->state = STATE_COLLECTING_VAR_LEN_DATA;
             break;
+        case MAN_WINBOND:
+            s->needed_bytes = 2;
+            s->state = STATE_COLLECTING_VAR_LEN_DATA;
+            break;
         default:
             s->needed_bytes = 1;
             s->state = STATE_COLLECTING_DATA;
@@ -1431,6 +1441,12 @@ static void decode_new_cmd(Flash *s, uint32_t value)
         case MAN_MACRONIX:
             s->quad_enable = true;
             break;
+        case MAN_WINBOND:
+            s->data[0] = (!!s->quad_enable) << 1;
+            s->pos = 0;
+            s->len = 1;
+            s->state = STATE_READING_DATA;
+            break;
         default:
             break;
         }
Signature · 1 line
2.34.1
#5 lore raw

PATCH v3 2/8 hw/net:ftgmac100: update ring base address to 64 bits

In reply to Jamin Lin via

Update TX and RX ring base address data type to uint64_t for 64 bits dram address DMA support.

Both "Normal Priority Transmit Ring Base Address Register(0x20)" and "Receive Ring Base Address Register (0x24)" are used for saving the low part physical address of descriptor manager.

Therefore, changes to set TX and RX descriptor manager address bits [31:0] in ftgmac100_read and ftgmac100_write functions.

Incrementing the version of vmstate to 2.

---
 hw/net/ftgmac100.c         | 33 ++++++++++++++++-----------------
 include/hw/net/ftgmac100.h |  9 ++++-----
 2 files changed, 20 insertions(+), 22 deletions(-)
hw/net/ftgmac100.c +16 -17
index 9e1f12cd33..d026242e2b 100644
@@ -515,12 +515,12 @@ out:
     return frame_size;
 }
 
-static void ftgmac100_do_tx(FTGMAC100State *s, uint32_t tx_ring,
-                            uint32_t tx_descriptor)
+static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
+                            uint64_t tx_descriptor)
 {
     int frame_size = 0;
     uint8_t *ptr = s->frame;
-    uint32_t addr = tx_descriptor;
+    uint64_t addr = tx_descriptor;
     uint32_t flags = 0;
 
     while (1) {
@@ -726,9 +726,9 @@ static uint64_t ftgmac100_read(void *opaque, hwaddr addr, unsigned size)
     case FTGMAC100_MATH1:
         return s->math[1];
     case FTGMAC100_RXR_BADR:
-        return s->rx_ring;
+        return extract64(s->rx_ring, 0, 32);
     case FTGMAC100_NPTXR_BADR:
-        return s->tx_ring;
+        return extract64(s->tx_ring, 0, 32);
     case FTGMAC100_ITC:
         return s->itc;
     case FTGMAC100_DBLAC:
@@ -799,9 +799,8 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
                           HWADDR_PRIx "\n", __func__, value);
             return;
         }
-
-        s->rx_ring = value;
-        s->rx_descriptor = s->rx_ring;
+        s->rx_ring = deposit64(s->rx_ring, 0, 32, value);
+        s->rx_descriptor = deposit64(s->rx_descriptor, 0, 32, value);
         break;
 
     case FTGMAC100_RBSR: /* DMA buffer size */
@@ -814,8 +813,8 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
                           HWADDR_PRIx "\n", __func__, value);
             return;
         }
-        s->tx_ring = value;
-        s->tx_descriptor = s->tx_ring;
+        s->tx_ring = deposit64(s->tx_ring, 0, 32, value);
+        s->tx_descriptor = deposit64(s->tx_descriptor, 0, 32, value);
         break;
 
     case FTGMAC100_NPTXPD: /* Trigger transmit */
@@ -957,7 +956,7 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
     FTGMAC100State *s = FTGMAC100(qemu_get_nic_opaque(nc));
     FTGMAC100Desc bd;
     uint32_t flags = 0;
-    uint32_t addr;
+    uint64_t addr;
     uint32_t crc;
     uint32_t buf_addr;
     uint8_t *crc_ptr;
@@ -1126,18 +1125,14 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
 
 static const VMStateDescription vmstate_ftgmac100 = {
     .name = TYPE_FTGMAC100,
-    .version_id = 1,
-    .minimum_version_id = 1,
+    .version_id = 2,
+    .minimum_version_id = 2,
     .fields = (const VMStateField[]) {
         VMSTATE_UINT32(irq_state, FTGMAC100State),
         VMSTATE_UINT32(isr, FTGMAC100State),
         VMSTATE_UINT32(ier, FTGMAC100State),
         VMSTATE_UINT32(rx_enabled, FTGMAC100State),
-        VMSTATE_UINT32(rx_ring, FTGMAC100State),
         VMSTATE_UINT32(rbsr, FTGMAC100State),
-        VMSTATE_UINT32(tx_ring, FTGMAC100State),
-        VMSTATE_UINT32(rx_descriptor, FTGMAC100State),
-        VMSTATE_UINT32(tx_descriptor, FTGMAC100State),
         VMSTATE_UINT32_ARRAY(math, FTGMAC100State, 2),
         VMSTATE_UINT32(itc, FTGMAC100State),
         VMSTATE_UINT32(aptcr, FTGMAC100State),
@@ -1156,6 +1151,10 @@ static const VMStateDescription vmstate_ftgmac100 = {
         VMSTATE_UINT32(phy_int_mask, FTGMAC100State),
         VMSTATE_UINT32(txdes0_edotr, FTGMAC100State),
         VMSTATE_UINT32(rxdes0_edorr, FTGMAC100State),
+        VMSTATE_UINT64(rx_ring, FTGMAC100State),
+        VMSTATE_UINT64(tx_ring, FTGMAC100State),
+        VMSTATE_UINT64(rx_descriptor, FTGMAC100State),
+        VMSTATE_UINT64(tx_descriptor, FTGMAC100State),
         VMSTATE_END_OF_LIST()
     }
 };
include/hw/net/ftgmac100.h +4 -5
index 269446e858..aae57ae8cb 100644
@@ -42,10 +42,6 @@ struct FTGMAC100State {
     uint32_t isr;
     uint32_t ier;
     uint32_t rx_enabled;
-    uint32_t rx_ring;
-    uint32_t rx_descriptor;
-    uint32_t tx_ring;
-    uint32_t tx_descriptor;
     uint32_t math[2];
     uint32_t rbsr;
     uint32_t itc;
@@ -58,7 +54,10 @@ struct FTGMAC100State {
     uint32_t phycr;
     uint32_t phydata;
     uint32_t fcr;
-
+    uint64_t rx_ring;
+    uint64_t rx_descriptor;
+    uint64_t tx_ring;
+    uint64_t tx_descriptor;
 
     uint32_t phy_status;
     uint32_t phy_control;
Signature · 1 line
2.34.1
Reviewed-by on v3 1/8
#2 lore raw

Re: [PATCH v3 1/8] hw/net:ftgmac100: update memory region size to 64KB

In reply to Jamin Lin via
Quoted 9 lines · Jamin Lin

According to the datasheet of ASPEED SOCs,
one MAC controller owns 128KB of register space for AST2500. However, one MAC controller only owns 64KB of register space for AST2600 and AST2700. It set the memory region size 128KB and it occupied another controllers Address Spaces.

Update one MAC controller memory region size to 0x1000 because AST2500 did not use register spaces over than 64KB.

Quoted 6 lines

Introduce a new container region size to 0x1000 and its range is from 0 to 0xfff. This container is mapped a sub region for the current set of register.
This sub region range is from 0 to 0xff.

Thanks,

C.

Quoted 49 lines
---
  hw/net/ftgmac100.c         | 11 ++++++++---
  include/hw/net/ftgmac100.h |  4 ++++
  2 files changed, 12 insertions(+), 3 deletions(-)
hw/net/ftgmac100.c +8 -3
index 25e4c0cd5b..9e1f12cd33 100644
@@ -1107,9 +1107,14 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
          s->rxdes0_edorr = FTGMAC100_RXDES0_EDORR;
      }
 
-    memory_region_init_io(&s->iomem, OBJECT(dev), &ftgmac100_ops, s,
-                          TYPE_FTGMAC100, 0x2000);
-    sysbus_init_mmio(sbd, &s->iomem);
+    memory_region_init(&s->iomem_container, OBJECT(s),
+                       TYPE_FTGMAC100 ".container", FTGMAC100_MEM_SIZE);
+    sysbus_init_mmio(sbd, &s->iomem_container);
+
+    memory_region_init_io(&s->iomem, OBJECT(s), &ftgmac100_ops, s,
+                          TYPE_FTGMAC100 ".regs", FTGMAC100_REG_MEM_SIZE);
+    memory_region_add_subregion(&s->iomem_container, 0x0, &s->iomem);
+
      sysbus_init_irq(sbd, &s->irq);
      qemu_macaddr_default_if_unset(&s->conf.macaddr);
 
include/hw/net/ftgmac100.h +4 -0
index 765d1538a4..269446e858 100644
@@ -14,6 +14,9 @@
  #define TYPE_FTGMAC100 "ftgmac100"
  OBJECT_DECLARE_SIMPLE_TYPE(FTGMAC100State, FTGMAC100)
 
+#define FTGMAC100_MEM_SIZE 0x1000
+#define FTGMAC100_REG_MEM_SIZE 0x100
+
  #include "hw/sysbus.h"
  #include "net/net.h"
 
@@ -30,6 +33,7 @@ struct FTGMAC100State {
      NICState *nic;
      NICConf conf;
      qemu_irq irq;
+    MemoryRegion iomem_container;
      MemoryRegion iomem;
 
      uint8_t frame[FTGMAC100_MAX_FRAME_SIZE];
Reviewed-by on v3 5/8
#14 lore raw

Re: [PATCH v3 5/8] aspeed/soc: set dma64 property for AST2700 ftgmac100

In reply to Jamin Lin via
Quoted 8 lines · Jamin Lin

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

Set dma64 property for ftgmac100 model to support
64bits dram address DMA.

Thanks,

C.

Quoted 21 lines
---
  hw/arm/aspeed_ast27x0.c | 3 +++
  1 file changed, 3 insertions(+)
hw/arm/aspeed_ast27x0.c +3 -0
index 18e6a8b10c..a9fb0d4b88 100644
@@ -552,9 +552,12 @@ static void aspeed_soc_ast2700_realize(DeviceState *dev, Error **errp)
          return;
      }
 
+    /* Net */
      for (i = 0; i < sc->macs_num; i++) {
          object_property_set_bool(OBJECT(&s->ftgmac100[i]), "aspeed", true,
                                   &error_abort);
+        object_property_set_bool(OBJECT(&s->ftgmac100[i]), "dma64", true,
+                                 &error_abort);
          if (!sysbus_realize(SYS_BUS_DEVICE(&s->ftgmac100[i]), errp)) {
              return;
          }
Reviewed-by on v3 7/8
#4 lore raw

Re: [PATCH v3 7/8] machine_aspeed.py: update to test ASPEED OpenBMC SDK v09.02 for AST2700

In reply to Jamin Lin via
Quoted 11 lines · Jamin Lin

Update test case to test ASPEED OpenBMC SDK v09.02 for AST2700.

ASPEED fixed TX mask issue from linux/drivers/ftgmac100.c. It is required to use ASPEED OpenBMC SDK since v09.02 for AST2700 QEMU network testing.

A test image is downloaded from the ASPEED Forked OpenBMC GitHub release repository :
https://github.com/AspeedTech-BMC/openbmc/releases/

Thanks,

C.

Quoted 27 lines
---
  tests/avocado/machine_aspeed.py | 6 +++---
  1 file changed, 3 insertions(+), 3 deletions(-)
tests/avocado/machine_aspeed.py +3 -3
index 3a20644fb2..13fe128fc9 100644
@@ -387,15 +387,15 @@ def test_arm_ast2600_evb_sdk(self):
          year = time.strftime("%Y")
          self.ssh_command_output_contains('/sbin/hwclock -f /dev/rtc1', year);
 
-    def test_aarch64_ast2700_evb_sdk_v09_01(self):
+    def test_aarch64_ast2700_evb_sdk_v09_02(self):
          """
          :avocado: tags=arch:aarch64
          :avocado: tags=machine:ast2700-evb
          """
 
          image_url = ('https://github.com/AspeedTech-BMC/openbmc/releases/'
-                     'download/v09.01/ast2700-default-obmc.tar.gz')
-        image_hash = 'b1cc0fd73c7650d34c9c8459a243f52a91e9e27144b8608b2645ab19461d1e07'
+                     'download/v09.02/ast2700-default-obmc.tar.gz')
+        image_hash = 'ac969c2602f4e6bdb69562ff466b89ae3fe1d86e1f6797bb7969d787f82116a7'
          image_path = self.fetch_asset(image_url, asset_hash=image_hash,
                                        algorithm='sha256')
          archive.extract(image_path, self.workdir)
Reviewed-by on v3 3/8
#8 lore raw

Re: [PATCH v3 3/8] hw/net:ftgmac100: introduce TX and RX ring base address high registers to support 64 bits

In reply to Jamin Lin via
Quoted 16 lines · Jamin Lin

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

It have "Normal Priority Transmit Ring Base Address Register High(0x17C)", "High Priority Transmit Ring Base Address Register High(0x184)" and "Receive Ring Base Address Register High(0x18C)" to save the high part physical address of descriptor manager.
Ex: TX descriptor manager address [34:0]
The "Normal Priority Transmit Ring Base Address Register High(0x17C)" bits [2:0] which corresponds the bits [34:32] of the 64 bits address of the TX ring buffer address.
The "Normal Priority Transmit Ring Base Address Register(0x20)" bits [31:0] which corresponds the bits [31:0] of the 64 bits address
of the TX ring buffer address.

Quoted 8 lines

Introduce a new sub region which size is 0x100 for the set of new registers and map it at 0x100 in the container region.
This sub region range is from 0x100 to 0x1ff.

Introduce a new property and object attribute to activate the region for new registers. Introduce a new memop handlers for the new register read and write.

Thanks,

C.

Quoted 155 lines
---
  hw/net/ftgmac100.c         | 82 ++++++++++++++++++++++++++++++++++++++
  include/hw/net/ftgmac100.h |  4 ++
  2 files changed, 86 insertions(+)
hw/net/ftgmac100.c +82 -0
index d026242e2b..68956aeb94 100644
@@ -56,6 +56,16 @@
  #define FTGMAC100_PHYDATA         0x64
  #define FTGMAC100_FCR             0x68
 
+/*
+ * FTGMAC100 registers high
+ *
+ * values below are offset by - FTGMAC100_REG_HIGH_OFFSET from datasheet
+ * because its memory region is start at FTGMAC100_REG_HIGH_OFFSET
+ */
+#define FTGMAC100_NPTXR_BADR_HIGH   (0x17C - FTGMAC100_REG_HIGH_OFFSET)
+#define FTGMAC100_HPTXR_BADR_HIGH   (0x184 - FTGMAC100_REG_HIGH_OFFSET)
+#define FTGMAC100_RXR_BADR_HIGH     (0x18C - FTGMAC100_REG_HIGH_OFFSET)
+
  /*
   * Interrupt status register & interrupt enable register
   */
@@ -913,6 +923,60 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
      ftgmac100_update_irq(s);
  }
 
+static uint64_t ftgmac100_high_read(void *opaque, hwaddr addr, unsigned size)
+{
+    FTGMAC100State *s = FTGMAC100(opaque);
+    uint64_t val = 0;
+
+    switch (addr) {
+    case FTGMAC100_NPTXR_BADR_HIGH:
+        val = extract64(s->tx_ring, 32, 32);
+        break;
+    case FTGMAC100_HPTXR_BADR_HIGH:
+        /* High Priority Transmit Ring Base High Address */
+        qemu_log_mask(LOG_UNIMP, "%s: read to unimplemented register 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    case FTGMAC100_RXR_BADR_HIGH:
+        val = extract64(s->rx_ring, 32, 32);
+        break;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad address at offset 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    }
+
+    return val;
+}
+
+static void ftgmac100_high_write(void *opaque, hwaddr addr,
+                          uint64_t value, unsigned size)
+{
+    FTGMAC100State *s = FTGMAC100(opaque);
+
+    switch (addr) {
+    case FTGMAC100_NPTXR_BADR_HIGH:
+        s->tx_ring = deposit64(s->tx_ring, 32, 32, value);
+        s->tx_descriptor = deposit64(s->tx_descriptor, 32, 32, value);
+        break;
+    case FTGMAC100_HPTXR_BADR_HIGH:
+        /* High Priority Transmit Ring Base High Address */
+        qemu_log_mask(LOG_UNIMP, "%s: write to unimplemented register 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    case FTGMAC100_RXR_BADR_HIGH:
+        s->rx_ring = deposit64(s->rx_ring, 32, 32, value);
+        s->rx_descriptor = deposit64(s->rx_descriptor, 32, 32, value);
+        break;
+    default:
+        qemu_log_mask(LOG_GUEST_ERROR, "%s: Bad address at offset 0x%"
+                      HWADDR_PRIx "\n", __func__, addr);
+        break;
+    }
+
+    ftgmac100_update_irq(s);
+}
+
  static int ftgmac100_filter(FTGMAC100State *s, const uint8_t *buf, size_t len)
  {
      unsigned mcast_idx;
@@ -1077,6 +1141,14 @@ static const MemoryRegionOps ftgmac100_ops = {
      .endianness = DEVICE_LITTLE_ENDIAN,
  };
 
+static const MemoryRegionOps ftgmac100_high_ops = {
+    .read = ftgmac100_high_read,
+    .write = ftgmac100_high_write,
+    .valid.min_access_size = 4,
+    .valid.max_access_size = 4,
+    .endianness = DEVICE_LITTLE_ENDIAN,
+};
+
  static void ftgmac100_cleanup(NetClientState *nc)
  {
      FTGMAC100State *s = FTGMAC100(qemu_get_nic_opaque(nc));
@@ -1114,6 +1186,15 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
                            TYPE_FTGMAC100 ".regs", FTGMAC100_REG_MEM_SIZE);
      memory_region_add_subregion(&s->iomem_container, 0x0, &s->iomem);
 
+    if (s->dma64) {
+        memory_region_init_io(&s->iomem_high, OBJECT(s), &ftgmac100_high_ops,
+                              s, TYPE_FTGMAC100 ".regs.high",
+                              FTGMAC100_REG_HIGH_MEM_SIZE);
+        memory_region_add_subregion(&s->iomem_container,
+                                    FTGMAC100_REG_HIGH_OFFSET,
+                                    &s->iomem_high);
+    }
+
      sysbus_init_irq(sbd, &s->irq);
      qemu_macaddr_default_if_unset(&s->conf.macaddr);
 
@@ -1162,6 +1243,7 @@ static const VMStateDescription vmstate_ftgmac100 = {
  static Property ftgmac100_properties[] = {
      DEFINE_PROP_BOOL("aspeed", FTGMAC100State, aspeed, false),
      DEFINE_NIC_PROPERTIES(FTGMAC100State, conf),
+    DEFINE_PROP_BOOL("dma64", FTGMAC100State, dma64, false),
      DEFINE_PROP_END_OF_LIST(),
  };
 
include/hw/net/ftgmac100.h +4 -0
index aae57ae8cb..24ccdf0260 100644
@@ -16,6 +16,8 @@ OBJECT_DECLARE_SIMPLE_TYPE(FTGMAC100State, FTGMAC100)
 
  #define FTGMAC100_MEM_SIZE 0x1000
  #define FTGMAC100_REG_MEM_SIZE 0x100
+#define FTGMAC100_REG_HIGH_MEM_SIZE 0x100
+#define FTGMAC100_REG_HIGH_OFFSET 0x100
 
  #include "hw/sysbus.h"
  #include "net/net.h"
@@ -35,6 +37,7 @@ struct FTGMAC100State {
      qemu_irq irq;
      MemoryRegion iomem_container;
      MemoryRegion iomem;
+    MemoryRegion iomem_high;
 
      uint8_t frame[FTGMAC100_MAX_FRAME_SIZE];
 
@@ -68,6 +71,7 @@ struct FTGMAC100State {
      bool aspeed;
      uint32_t txdes0_edotr;
      uint32_t rxdes0_edorr;
+    bool dma64;
  };
 
  #define TYPE_ASPEED_MII "aspeed-mmi"
Reviewed-by on v3 8/8
#12 lore raw

Re: [PATCH v3 8/8] machine_aspeed.py: update to test network for AST2700

In reply to Jamin Lin via
Quoted 9 lines · Jamin Lin

Update test case to test network connection via SSH.

Test command:

```
cd build
pyvenv/bin/avocado run ../qemu/tests/avocado/machine_aspeed.py:AST2x00MachineSDK.test_aarch64_ast2700_evb_sdk_v09_02
```

Thanks,

C.

Quoted 32 lines
---
  tests/avocado/machine_aspeed.py | 6 ++++--
  1 file changed, 4 insertions(+), 2 deletions(-)
tests/avocado/machine_aspeed.py +4 -2
index 13fe128fc9..f66ad38d35 100644
@@ -313,14 +313,14 @@ def do_test_arm_aspeed_sdk_start(self, image):
 
      def do_test_aarch64_aspeed_sdk_start(self, image):
          self.vm.set_console()
-        self.vm.add_args('-drive', 'file=' + image + ',if=mtd,format=raw')
+        self.vm.add_args('-drive', 'file=' + image + ',if=mtd,format=raw',
+                         '-net', 'nic', '-net', 'user,hostfwd=:127.0.0.1:0-:22')
 
          self.vm.launch()
 
          self.wait_for_console_pattern('U-Boot 2023.10')
          self.wait_for_console_pattern('## Loading kernel from FIT Image')
          self.wait_for_console_pattern('Starting kernel ...')
-        self.wait_for_console_pattern("systemd[1]: Hostname set to")
 
      @skipUnless(os.getenv('QEMU_TEST_FLAKY_TESTS'), 'Test is unstable on GitLab')
 
@@ -436,4 +436,6 @@ def test_aarch64_ast2700_evb_sdk_v09_02(self):
 
          self.vm.add_args('-smp', str(num_cpu))
          self.do_test_aarch64_aspeed_sdk_start(image_dir + 'image-bmc')
+        self.wait_for_console_pattern('nodistro.0 ast2700-default ttyS12')
+        self.ssh_connect('root', '0penBmc', False)
 
Reviewed-by on v3 2/8
#6 lore raw

Re: [PATCH v3 2/8] hw/net:ftgmac100: update ring base address to 64 bits

In reply to Jamin Lin via
Quoted 7 lines · Jamin Lin

Update TX and RX ring base address data type to uint64_t for 64 bits dram address DMA support.

Both "Normal Priority Transmit Ring Base Address Register(0x20)" and "Receive Ring Base Address Register (0x24)" are used for saving the low part physical address of descriptor manager.

Quoted 6 lines

Therefore, changes to set TX and RX descriptor manager address bits [31:0] in ftgmac100_read and ftgmac100_write functions.

Incrementing the version of vmstate to 2.

Thanks,

C.

Quoted 128 lines
---
  hw/net/ftgmac100.c         | 33 ++++++++++++++++-----------------
  include/hw/net/ftgmac100.h |  9 ++++-----
  2 files changed, 20 insertions(+), 22 deletions(-)
hw/net/ftgmac100.c +16 -17
index 9e1f12cd33..d026242e2b 100644
@@ -515,12 +515,12 @@ out:
      return frame_size;
  }
 
-static void ftgmac100_do_tx(FTGMAC100State *s, uint32_t tx_ring,
-                            uint32_t tx_descriptor)
+static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
+                            uint64_t tx_descriptor)
  {
      int frame_size = 0;
      uint8_t *ptr = s->frame;
-    uint32_t addr = tx_descriptor;
+    uint64_t addr = tx_descriptor;
      uint32_t flags = 0;
 
      while (1) {
@@ -726,9 +726,9 @@ static uint64_t ftgmac100_read(void *opaque, hwaddr addr, unsigned size)
      case FTGMAC100_MATH1:
          return s->math[1];
      case FTGMAC100_RXR_BADR:
-        return s->rx_ring;
+        return extract64(s->rx_ring, 0, 32);
      case FTGMAC100_NPTXR_BADR:
-        return s->tx_ring;
+        return extract64(s->tx_ring, 0, 32);
      case FTGMAC100_ITC:
          return s->itc;
      case FTGMAC100_DBLAC:
@@ -799,9 +799,8 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
                            HWADDR_PRIx "\n", __func__, value);
              return;
          }
-
-        s->rx_ring = value;
-        s->rx_descriptor = s->rx_ring;
+        s->rx_ring = deposit64(s->rx_ring, 0, 32, value);
+        s->rx_descriptor = deposit64(s->rx_descriptor, 0, 32, value);
          break;
 
      case FTGMAC100_RBSR: /* DMA buffer size */
@@ -814,8 +813,8 @@ static void ftgmac100_write(void *opaque, hwaddr addr,
                            HWADDR_PRIx "\n", __func__, value);
              return;
          }
-        s->tx_ring = value;
-        s->tx_descriptor = s->tx_ring;
+        s->tx_ring = deposit64(s->tx_ring, 0, 32, value);
+        s->tx_descriptor = deposit64(s->tx_descriptor, 0, 32, value);
          break;
 
      case FTGMAC100_NPTXPD: /* Trigger transmit */
@@ -957,7 +956,7 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
      FTGMAC100State *s = FTGMAC100(qemu_get_nic_opaque(nc));
      FTGMAC100Desc bd;
      uint32_t flags = 0;
-    uint32_t addr;
+    uint64_t addr;
      uint32_t crc;
      uint32_t buf_addr;
      uint8_t *crc_ptr;
@@ -1126,18 +1125,14 @@ static void ftgmac100_realize(DeviceState *dev, Error **errp)
 
  static const VMStateDescription vmstate_ftgmac100 = {
      .name = TYPE_FTGMAC100,
-    .version_id = 1,
-    .minimum_version_id = 1,
+    .version_id = 2,
+    .minimum_version_id = 2,
      .fields = (const VMStateField[]) {
          VMSTATE_UINT32(irq_state, FTGMAC100State),
          VMSTATE_UINT32(isr, FTGMAC100State),
          VMSTATE_UINT32(ier, FTGMAC100State),
          VMSTATE_UINT32(rx_enabled, FTGMAC100State),
-        VMSTATE_UINT32(rx_ring, FTGMAC100State),
          VMSTATE_UINT32(rbsr, FTGMAC100State),
-        VMSTATE_UINT32(tx_ring, FTGMAC100State),
-        VMSTATE_UINT32(rx_descriptor, FTGMAC100State),
-        VMSTATE_UINT32(tx_descriptor, FTGMAC100State),
          VMSTATE_UINT32_ARRAY(math, FTGMAC100State, 2),
          VMSTATE_UINT32(itc, FTGMAC100State),
          VMSTATE_UINT32(aptcr, FTGMAC100State),
@@ -1156,6 +1151,10 @@ static const VMStateDescription vmstate_ftgmac100 = {
          VMSTATE_UINT32(phy_int_mask, FTGMAC100State),
          VMSTATE_UINT32(txdes0_edotr, FTGMAC100State),
          VMSTATE_UINT32(rxdes0_edorr, FTGMAC100State),
+        VMSTATE_UINT64(rx_ring, FTGMAC100State),
+        VMSTATE_UINT64(tx_ring, FTGMAC100State),
+        VMSTATE_UINT64(rx_descriptor, FTGMAC100State),
+        VMSTATE_UINT64(tx_descriptor, FTGMAC100State),
          VMSTATE_END_OF_LIST()
      }
  };
include/hw/net/ftgmac100.h +4 -5
index 269446e858..aae57ae8cb 100644
@@ -42,10 +42,6 @@ struct FTGMAC100State {
      uint32_t isr;
      uint32_t ier;
      uint32_t rx_enabled;
-    uint32_t rx_ring;
-    uint32_t rx_descriptor;
-    uint32_t tx_ring;
-    uint32_t tx_descriptor;
      uint32_t math[2];
      uint32_t rbsr;
      uint32_t itc;
@@ -58,7 +54,10 @@ struct FTGMAC100State {
      uint32_t phycr;
      uint32_t phydata;
      uint32_t fcr;
-
+    uint64_t rx_ring;
+    uint64_t rx_descriptor;
+    uint64_t tx_ring;
+    uint64_t tx_descriptor;
 
      uint32_t phy_status;
      uint32_t phy_control;
Reviewed-by on v3 4/8
#10 lore raw

Re: [PATCH v3 4/8] hw/net:ftgmac100: update TX and RX packet buffers address to 64 bits

In reply to Jamin Lin via
Quoted 12 lines · Jamin Lin

ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35) And the base address of dram is "0x4 00000000" which is 64bits address.

It have "TXDES 2" and "RXDES 2" to save the high part physical address of packet buffer.
Ex: TX packet buffer address [34:0]
The "TXDES 2" bits [18:16] which corresponds the bits [34:32] of the 64 bits address of the TX packet buffer address and "TXDES 3" bits [31:0] which corresponds the bits [31:0] of the 64 bits address of the TX packet buffer address.

Quoted 4 lines

Update TX and RX packet buffers address type to
64 bits for dram 64 bits address DMA support.

Thanks,

C.

Quoted 78 lines
---
  hw/net/ftgmac100.c | 21 ++++++++++++++++++---
  1 file changed, 18 insertions(+), 3 deletions(-)
hw/net/ftgmac100.c +18 -3
index 68956aeb94..80f9cd56d5 100644
@@ -175,6 +175,8 @@
  #define FTGMAC100_TXDES1_TX2FIC          (1 << 30)
  #define FTGMAC100_TXDES1_TXIC            (1 << 31)
 
+#define FTGMAC100_TXDES2_TXBUF_BADR_HI(x)   (((x) >> 16) & 0x7)
+
  /*
   * Receive descriptor
   */
@@ -208,13 +210,15 @@
  #define FTGMAC100_RXDES1_UDP_CHKSUM_ERR  (1 << 26)
  #define FTGMAC100_RXDES1_IP_CHKSUM_ERR   (1 << 27)
 
+#define FTGMAC100_RXDES2_RXBUF_BADR_HI(x)   (((x) >> 16) & 0x7)
+
  /*
   * Receive and transmit Buffer Descriptor
   */
  typedef struct {
      uint32_t        des0;
      uint32_t        des1;
-    uint32_t        des2;        /* not used by HW */
+    uint32_t        des2;        /* used by HW 64 bits DMA */
      uint32_t        des3;
  } FTGMAC100Desc;
 
@@ -531,6 +535,7 @@ static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
      int frame_size = 0;
      uint8_t *ptr = s->frame;
      uint64_t addr = tx_descriptor;
+    uint64_t buf_addr = 0;
      uint32_t flags = 0;
 
      while (1) {
@@ -569,7 +574,12 @@ static void ftgmac100_do_tx(FTGMAC100State *s, uint64_t tx_ring,
              len =  sizeof(s->frame) - frame_size;
          }
 
-        if (dma_memory_read(&address_space_memory, bd.des3,
+        buf_addr = bd.des3;
+        if (s->dma64) {
+            buf_addr = deposit64(buf_addr, 32, 32,
+                                 FTGMAC100_TXDES2_TXBUF_BADR_HI(bd.des2));
+        }
+        if (dma_memory_read(&address_space_memory, buf_addr,
                              ptr, len, MEMTXATTRS_UNSPECIFIED)) {
              qemu_log_mask(LOG_GUEST_ERROR, "%s: failed to read packet @ 0x%x\n",
                            __func__, bd.des3);
@@ -1022,7 +1032,7 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
      uint32_t flags = 0;
      uint64_t addr;
      uint32_t crc;
-    uint32_t buf_addr;
+    uint64_t buf_addr = 0;
      uint8_t *crc_ptr;
      uint32_t buf_len;
      size_t size = len;
@@ -1087,7 +1097,12 @@ static ssize_t ftgmac100_receive(NetClientState *nc, const uint8_t *buf,
          if (size < 4) {
              buf_len += size - 4;
          }
+
          buf_addr = bd.des3;
+        if (s->dma64) {
+            buf_addr = deposit64(buf_addr, 32, 32,
+                                 FTGMAC100_RXDES2_RXBUF_BADR_HI(bd.des2));
+        }
          if (first && proto == ETH_P_VLAN && buf_len >= 18) {
              bd.des1 = lduw_be_p(buf + 14) | FTGMAC100_RXDES1_VLANTAG_AVAIL;
 
#16 lore raw
In reply to Jamin Lin via
Quoted 33 lines · Jamin Lin

change from v1:
- ftgmac100
- fix coding style
- support 64 bits dma dram address for AST2700

change from v2:
- ftgmac100: update memory region size to 0x200.
- ftgmac100: introduce a new class(ftgmac100_high),
class attribute and memop handlers, for FTGMAC100_*_HIGH regs read/write.
- aspeed_ast27x0: update network model to ftgmac100_high to support 64 bits dram address DMA.
- m25p80: support quad mode for w25q01jvq

change from v3:
- ftgmac100: update memory region size to 64KB.
- ftgmac100: using a property to activate the region for new registers, instead of a class
- ftgmac100: introduce TX and RX ring base address high registers
- ftgmac100: split standalone patch for easy review
- ftgmac100: update TX and RX packet buffers address to 64 bits
- aspeed_ast27x0: set dma64 property for AST2700 ftgmac100
- machine_aspeed.py: update to test sdk v09.02 and network for AST2700

Jamin Lin (8):
hw/net:ftgmac100: update memory region size to 64KB hw/net:ftgmac100: update ring base address to 64 bits hw/net:ftgmac100: introduce TX and RX ring base address high registers
to support 64 bits
hw/net:ftgmac100: update TX and RX packet buffers address to 64 bits aspeed/soc: set dma64 property for AST2700 ftgmac100 hw/block: m25p80: support quad mode for w25q01jvq machine_aspeed.py: update to test ASPEED OpenBMC SDK v09.02 for

     AST2700
Quoted 9 lines

machine_aspeed.py: update to test network for AST2700

  hw/arm/aspeed_ast27x0.c         |   3 +
  hw/block/m25p80.c               |  16 ++++
  hw/net/ftgmac100.c              | 147 +++++++++++++++++++++++++++-----
  include/hw/net/ftgmac100.h      |  17 ++--
  tests/avocado/machine_aspeed.py |  12 +--
  5 files changed, 162 insertions(+), 33 deletions(-)

Applied to aspeed-next.

Thanks,

C.