riscv: spacemit: bananapi_f3: add support for Banana Pi F3 board
Subsystems (2)
cover riscv: spacemit: bananapi_f3: add support for Banana Pi F3 board
Banana Pi F3 board is a industrial grade RISC-V development board, it design with SpacemiT K1 8 core RISC-V chip, CPU integrates 2.0 TOPs AI computing power. 4G DDR and 16G eMMC onboard.2x GbE Ethernet prot, 4x USB 3.0 and PCIe for M.2 interface, support HDMI and Dual MIPI-CSI Camera.
This patch introduces fundamental support for the Banana Pi F3 board, encompassing UART, CPU, and PLIC support. This ensures that U-Boot can operate in serial console mode.
Kongyang Liu (2):
riscv: spacemit: bananapi_f3: initial support added
doc: spacemit: bananapi_f3: document Banana Pi F3 board
arch/riscv/Kconfig | 5 + arch/riscv/cpu/k1/Kconfig | 18 ++ arch/riscv/cpu/k1/Makefile | 6 + arch/riscv/cpu/k1/cpu.c | 9 + arch/riscv/cpu/k1/dram.c | 39 +++ arch/riscv/dts/Makefile | 1 + arch/riscv/dts/k1-bananapi-f3.dts | 20 ++ arch/riscv/dts/k1.dtsi | 375 +++++++++++++++++++++++++ board/spacemit/bananapi_f3/Kconfig | 25 ++ board/spacemit/bananapi_f3/MAINTAINERS | 6 + board/spacemit/bananapi_f3/Makefile | 5 + board/spacemit/bananapi_f3/board.c | 9 + configs/bananapi_f3_defconfig | 20 ++ doc/board/index.rst | 1 + doc/board/spacemit/bananapi_f3.rst | 78 +++++ doc/board/spacemit/index.rst | 8 + include/configs/bananapi_f3.h | 15 + 17 files changed, 640 insertions(+) create mode 100644 arch/riscv/cpu/k1/Kconfig create mode 100644 arch/riscv/cpu/k1/Makefile create mode 100644 arch/riscv/cpu/k1/cpu.c create mode 100644 arch/riscv/cpu/k1/dram.c create mode 100644 arch/riscv/dts/k1-bananapi-f3.dts create mode 100644 arch/riscv/dts/k1.dtsi create mode 100644 board/spacemit/bananapi_f3/Kconfig create mode 100644 board/spacemit/bananapi_f3/MAINTAINERS create mode 100644 board/spacemit/bananapi_f3/Makefile create mode 100644 board/spacemit/bananapi_f3/board.c create mode 100644 configs/bananapi_f3_defconfig create mode 100644 doc/board/spacemit/bananapi_f3.rst create mode 100644 doc/board/spacemit/index.rst create mode 100644 include/configs/bananapi_f3.h
Signature · 1 line
2.41.0
PATCH 1/2 riscv: spacemit: bananapi_f3: initial support added
Add basic support for SpacemiT's Banana Pi F3 board
---
arch/riscv/Kconfig | 5 + arch/riscv/cpu/k1/Kconfig | 18 ++ arch/riscv/cpu/k1/Makefile | 6 + arch/riscv/cpu/k1/cpu.c | 9 + arch/riscv/cpu/k1/dram.c | 39 +++ arch/riscv/dts/Makefile | 1 + arch/riscv/dts/k1-bananapi-f3.dts | 20 ++ arch/riscv/dts/k1.dtsi | 375 +++++++++++++++++++++++++ board/spacemit/bananapi_f3/Kconfig | 25 ++ board/spacemit/bananapi_f3/MAINTAINERS | 6 + board/spacemit/bananapi_f3/Makefile | 5 + board/spacemit/bananapi_f3/board.c | 9 + configs/bananapi_f3_defconfig | 20 ++ include/configs/bananapi_f3.h | 15 + 14 files changed, 553 insertions(+) create mode 100644 arch/riscv/cpu/k1/Kconfig create mode 100644 arch/riscv/cpu/k1/Makefile create mode 100644 arch/riscv/cpu/k1/cpu.c create mode 100644 arch/riscv/cpu/k1/dram.c create mode 100644 arch/riscv/dts/k1-bananapi-f3.dts create mode 100644 arch/riscv/dts/k1.dtsi create mode 100644 board/spacemit/bananapi_f3/Kconfig create mode 100644 board/spacemit/bananapi_f3/MAINTAINERS create mode 100644 board/spacemit/bananapi_f3/Makefile create mode 100644 board/spacemit/bananapi_f3/board.c create mode 100644 configs/bananapi_f3_defconfig create mode 100644 include/configs/bananapi_f3.h
arch/riscv/Kconfig +5 -0
@@ -11,6 +11,9 @@ choice config TARGET_ANDES_AE350 bool "Support Andes ae350" +config TARGET_BANANAPI_F3 + bool "Support BananaPi F3 Board" + config TARGET_MICROCHIP_ICICLE bool "Support Microchip PolarFire-SoC Icicle Board"
@@ -88,6 +91,7 @@ source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" source "board/sipeed/maix/Kconfig" source "board/sophgo/milkv_duo/Kconfig" +source "board/spacemit/bananapi_f3/Kconfig" source "board/starfive/visionfive2/Kconfig" source "board/thead/th1520_lpi4a/Kconfig" source "board/xilinx/mbv/Kconfig"
@@ -99,6 +103,7 @@ source "arch/riscv/cpu/fu540/Kconfig" source "arch/riscv/cpu/fu740/Kconfig" source "arch/riscv/cpu/generic/Kconfig" source "arch/riscv/cpu/jh7110/Kconfig" +source "arch/riscv/cpu/k1/Kconfig" # architecture-specific options below
arch/riscv/cpu/k1/Kconfig new file +18 -0
@@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2024, Kongyang Liu <[email protected]> + +config SPACEMIT_K1 + bool + select BINMAN + select ARCH_EARLY_INIT_R + select SYS_CACHE_SHIFT_6 + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if (RISCV_SMODE || SPL_RISCV_SMODE) + imply RISCV_ACLINT if RISCV_MMODE + imply SPL_RISCV_ACLINT if SPL_RISCV_MMODE + imply CMD_CPU + imply SPL_CPU + imply SPL_OPENSBI + imply SPL_LOAD_FIT
arch/riscv/cpu/k1/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y += dram.o +obj-y += cpu.o
arch/riscv/cpu/k1/cpu.c new file +9 -0
@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int cleanup_before_linux (void ) +{ +return 0 ; +}
arch/riscv/cpu/k1/dram.c new file +39 -0
@@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +#include <asm/global_data.h> +#include <config.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int dram_init (void ) +{ + gd->ram_base =CFG_SYS_SDRAM_BASE ; +/* TODO get ram size from ddr controller */ + gd->ram_size =SZ_4G ; +return 0 ; +} + +int dram_init_banksize (void ) +{ + gd->bd->bi_dram[0 ].start =CFG_SYS_SDRAM_BASE ; + gd->bd->bi_dram[0 ].size =min_t (phys_size_t, gd->ram_size,SZ_2G ); + +if (gd->ram_size >SZ_2G &&CONFIG_NR_DRAM_BANKS >1 ) { + gd->bd->bi_dram[1 ].start =0x100000000 ; + gd->bd->bi_dram[1 ].size = gd->ram_size -SZ_2G ; + } + +return 0 ; +} + +phys_addr_t board_get_usable_ram_top (phys_size_t total_size) +{ +if (gd->ram_size >SZ_2G ) +return SZ_2G ; + +return gd->ram_size; +}
arch/riscv/dts/Makefile +1 -0
@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0+ dtb-$(CONFIG_TARGET_ANDES_AE350) += ae350_32.dtb ae350_64.dtb +dtb-$(CONFIG_TARGET_BANANAPI_F3) += k1-bananapi-f3.dtb dtb-$(CONFIG_TARGET_MICROCHIP_ICICLE) += mpfs-icicle-kit.dtb dtb-$(CONFIG_TARGET_MILKV_DUO) += cv1800b-milkv-duo.dtb dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt32.dtb qemu-virt64.dtb
arch/riscv/dts/k1-bananapi-f3.dts new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2024 Yangyu Chen <[email protected]> + */ + +#include "k1.dtsi" +#include "binman.dtsi" + +/ { + model = "Banana Pi BPI-F3"; + compatible = "bananapi,bpi-f3", "spacemit,k1"; + + chosen { + stdout-path = "serial0"; + }; +}; + +&uart0 { + status = "okay"; +};
arch/riscv/dts/k1.dtsi new file +375 -0
375 lines not on this page · raw message
board/spacemit/bananapi_f3/Kconfig new file +25 -0
@@ -0,0 +1,25 @@ +if TARGET_BANANAPI_F3 + +config SYS_BOARD + default "bananapi_f3" + +config SYS_VENDOR + default "spacemit" + +config SYS_CPU + default "k1" + +config SYS_CONFIG_NAME + default "bananapi_f3" + +config TEXT_BASE + default 0x00200000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x00000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select SPACEMIT_K1 + +endif
board/spacemit/bananapi_f3/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +BananaPi F3 +M: Kongyang Liu <[email protected]> +S: Maintained +F: board/spacemit/bananapi_f3/ +F: configs/bananapi_f3_defconfig +F: doc/board/spacemit/bananapi_f3.rst
board/spacemit/bananapi_f3/Makefile new file +5 -0
@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y := board.o
board/spacemit/bananapi_f3/board.c new file +9 -0
@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int board_init (void ) +{ +return 0 ; +}
configs/bananapi_f3_defconfig new file +20 -0
@@ -0,0 +1,20 @@ +CONFIG_RISCV=y +CONFIG_SYS_MALLOC_LEN=0x1000000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000000 +CONFIG_DEFAULT_DEVICE_TREE="k1-bananapi-f3" +CONFIG_SYS_LOAD_ADDR=0x200000 +CONFIG_TARGET_BANANAPI_F3=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0xa000000 +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_SYS_CBSIZE=256 +CONFIG_SYS_PBSIZE=276 +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="bananapi_f3# " +CONFIG_ENV_OVERWRITE=y +CONFIG_SYS_NS16550=y +CONFIG_SYS_NS16550_MEM32=y
include/configs/bananapi_f3.h new file +15 -0
@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +* +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <linux/serial_reg.h> + +#define CFG_SYS_SDRAM_BASE 0x0 +#define CFG_SYS_NS16550_IER UART_IER_UUE + +#endif /* __CONFIG_H */
Signature · 1 line
2.41.0
Re: [PATCH 1/2] riscv: spacemit: bananapi_f3: initial support added
Quoted 106 lines · Kongyang Liu
Add basic support for SpacemiT's Banana Pi F3 board
Signed-off-by Kongyang Liu <[email protected]>---
arch/riscv/Kconfig | 5 + arch/riscv/cpu/k1/Kconfig | 18 ++ arch/riscv/cpu/k1/Makefile | 6 + arch/riscv/cpu/k1/cpu.c | 9 + arch/riscv/cpu/k1/dram.c | 39 +++ arch/riscv/dts/Makefile | 1 + arch/riscv/dts/k1-bananapi-f3.dts | 20 ++ arch/riscv/dts/k1.dtsi | 375 +++++++++++++++++++++++++ board/spacemit/bananapi_f3/Kconfig | 25 ++ board/spacemit/bananapi_f3/MAINTAINERS | 6 + board/spacemit/bananapi_f3/Makefile | 5 + board/spacemit/bananapi_f3/board.c | 9 + configs/bananapi_f3_defconfig | 20 ++ include/configs/bananapi_f3.h | 15 + 14 files changed, 553 insertions(+)create mode 100644
arch/riscv/cpu/k1/Kconfigcreate mode 100644arch/riscv/cpu/k1/Makefilecreate mode 100644arch/riscv/cpu/k1/cpu.ccreate mode 100644arch/riscv/cpu/k1/dram.ccreate mode 100644arch/riscv/dts/k1-bananapi-f3.dtscreate mode 100644arch/riscv/dts/k1.dtsi
create mode 100644 board/spacemit/bananapi_f3/Kconfig create mode 100644 board/spacemit/bananapi_f3/MAINTAINERS create mode 100644 board/spacemit/bananapi_f3/Makefile create mode 100644board/spacemit/bananapi_f3/board.ccreate mode 100644 configs/bananapi_f3_defconfig create mode 100644include/configs/bananapi_f3.harch/riscv/Kconfig +5
-0@@ -11,6 +11,9 @@ choice config TARGET_ANDES_AE350 bool "Support Andes ae350" +config TARGET_BANANAPI_F3 + bool "Support BananaPi F3 Board" + config TARGET_MICROCHIP_ICICLE bool "Support Microchip PolarFire-SoC Icicle Board"@@ -88,6 +91,7 @@ source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" source "board/sipeed/maix/Kconfig" source "board/sophgo/milkv_duo/Kconfig" +source "board/spacemit/bananapi_f3/Kconfig" source "board/starfive/visionfive2/Kconfig" source "board/thead/th1520_lpi4a/Kconfig" source "board/xilinx/mbv/Kconfig"@@ -99,6 +103,7 @@ source "arch/riscv/cpu/fu540/Kconfig" source "arch/riscv/cpu/fu740/Kconfig" source "arch/riscv/cpu/generic/Kconfig" source "arch/riscv/cpu/jh7110/Kconfig" +source "arch/riscv/cpu/k1/Kconfig" # architecture-specific options belowarch/riscv/cpu/k1/Kconfig new file +18
-0@@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2024, Kongyang Liu <[email protected]> + +config SPACEMIT_K1 + bool + select BINMAN + select ARCH_EARLY_INIT_R + select SYS_CACHE_SHIFT_6 + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if (RISCV_SMODE || SPL_RISCV_SMODE) + imply RISCV_ACLINT if RISCV_MMODE + imply SPL_RISCV_ACLINT if SPL_RISCV_MMODE + imply CMD_CPU + imply SPL_CPU + imply SPL_OPENSBI + imply SPL_LOAD_FITarch/riscv/cpu/k1/Makefile new file +6
-0@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y += dram.o +obj-y += cpu.oarch/riscv/cpu/k1/cpu.c new file +0
-0
arch/riscv/cpu/k1/cpu.c line 1
Quoted 1 line
arch/riscv/cpu/k1/cpu.c new file +1
-0@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+
Thanks a lot for adding the board.
GPL-2.0-or-later, see https://spdx.org/licenses/GPL-2.0-or-later.html
Quoted 14 lines
arch/riscv/cpu/k1/cpu.c new file +8
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int cleanup_before_linux (void ) +{ +return 0 ; +}arch/riscv/cpu/k1/dram.c new file +0
-0
arch/riscv/cpu/k1/dram.c line 1
Quoted 1 line
arch/riscv/cpu/k1/dram.c new file +1
-0@@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0+
ditto
Quoted 82 lines
arch/riscv/cpu/k1/dram.c new file +38
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +#include <asm/global_data.h> +#include <config.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int dram_init (void ) +{ + gd->ram_base =CFG_SYS_SDRAM_BASE ; +/* TODO get ram size from ddr controller */ + gd->ram_size =SZ_4G ; +return 0 ; +} + +int dram_init_banksize (void ) +{ + gd->bd->bi_dram[0 ].start =CFG_SYS_SDRAM_BASE ; + gd->bd->bi_dram[0 ].size =min_t (phys_size_t, gd->ram_size,SZ_2G ); + +if (gd->ram_size >SZ_2G &&CONFIG_NR_DRAM_BANKS >1 ) { + gd->bd->bi_dram[1 ].start =0x100000000 ; + gd->bd->bi_dram[1 ].size = gd->ram_size -SZ_2G ; + } + +return 0 ; +} + +phys_addr_t board_get_usable_ram_top (phys_size_t total_size) +{ +if (gd->ram_size >SZ_2G ) +return SZ_2G ; + +return gd->ram_size; +}arch/riscv/dts/Makefile +1
-0@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0+ dtb-$(CONFIG_TARGET_ANDES_AE350) += ae350_32.dtb ae350_64.dtb +dtb-$(CONFIG_TARGET_BANANAPI_F3) += k1-bananapi-f3.dtb dtb-$(CONFIG_TARGET_MICROCHIP_ICICLE) += mpfs-icicle-kit.dtb dtb-$(CONFIG_TARGET_MILKV_DUO) += cv1800b-milkv-duo.dtb dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt32.dtb qemu-virt64.dtbarch/riscv/dts/k1-bananapi-f3.dts new file +20
-0@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2024 Yangyu Chen <[email protected]> + */ + +#include "k1.dtsi" +#include "binman.dtsi" + +/ { + model = "Banana Pi BPI-F3"; + compatible = "bananapi,bpi-f3", "spacemit,k1"; + + chosen { + stdout-path = "serial0"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/k1.dtsi new file +0
-0
arch/riscv/dts/k1.dtsi line 1
Quoted 1 line
arch/riscv/dts/k1.dtsi new file +1
-0@@ -0,0 +1,375 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT
Elsewhere you use GPL-2.0-or-later. Any special reason to be more restrictive here?
arch/riscv/dts/k1.dtsi line 11
Quoted 10 lines
arch/riscv/dts/k1.dtsi new file +10
-0+/* + * Copyright (C) 2024 Yangyu Chen <[email protected]> + */ + +/dts-v1/; +/ { + #address-cells = <2>; + #size-cells = <2>; + model = "SpacemiT K1"; + compatible = "spacemit,k1";
According to the devicetree specification "a memory device node is required for all devicetrees".
Quoted 413 lines
arch/riscv/dts/k1.dtsi new file +364
-0+ + aliases { + serial0 = &uart0; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <24000000>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu_0>; + }; + core1 { + cpu = <&cpu_1>; + }; + core2 { + cpu = <&cpu_2>; + }; + core3 { + cpu = <&cpu_3>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu_4>; + }; + core1 { + cpu = <&cpu_5>; + }; + core2 { + cpu = <&cpu_6>; + }; + core3 { + cpu = <&cpu_7>; + }; + }; + }; + + cpu_0: cpu@0 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <0>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_1: cpu@1 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <1>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_2: cpu@2 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <2>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_3: cpu@3 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <3>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_4: cpu@4 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <4>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu4_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_5: cpu@5 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <5>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu5_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_6: cpu@6 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <6>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu6_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_7: cpu@7 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <7>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu7_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + dma-noncoherent; + ranges; + + uart0: serial@d4017000 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017000 0x0 0x100>; + interrupts = <42>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart2: serial@d4017100 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017100 0x0 0x100>; + interrupts = <44>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@d4017200 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017200 0x0 0x100>; + interrupts = <45>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart4: serial@d4017300 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017300 0x0 0x100>; + interrupts = <46>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@d4017400 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017400 0x0 0x100>; + interrupts = <47>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart6: serial@d4017500 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017500 0x0 0x100>; + interrupts = <48>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart7: serial@d4017600 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017600 0x0 0x100>; + interrupts = <49>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart8: serial@d4017700 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017700 0x0 0x100>; + interrupts = <50>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart9: serial@d4017800 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017800 0x0 0x100>; + interrupts = <51>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + plic: interrupt-controller@e0000000 { + compatible = "spacemit,k1-plic", "sifive,plic-1.0.0"; + reg = <0x0 0xe0000000 0x0 0x4000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>, + <&cpu4_intc 11>, <&cpu4_intc 9>, + <&cpu5_intc 11>, <&cpu5_intc 9>, + <&cpu6_intc 11>, <&cpu6_intc 9>, + <&cpu7_intc 11>, <&cpu7_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + riscv,ndev = <159>; + }; + + clint: timer@e4000000 { + compatible = "spacemit,k1-clint", "sifive,clint0"; + reg = <0x0 0xe4000000 0x0 0x10000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>, + <&cpu4_intc 3>, <&cpu4_intc 7>, + <&cpu5_intc 3>, <&cpu5_intc 7>, + <&cpu6_intc 3>, <&cpu6_intc 7>, + <&cpu7_intc 3>, <&cpu7_intc 7>; + }; + }; +};board/spacemit/bananapi_f3/Kconfig new file +25
-0@@ -0,0 +1,25 @@ +if TARGET_BANANAPI_F3 + +config SYS_BOARD + default "bananapi_f3" + +config SYS_VENDOR + default "spacemit" + +config SYS_CPU + default "k1" + +config SYS_CONFIG_NAME + default "bananapi_f3" + +config TEXT_BASE + default 0x00200000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x00000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select SPACEMIT_K1 + +endifboard/spacemit/bananapi_f3/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +BananaPi F3 +M: Kongyang Liu <[email protected]> +S: Maintained +F: board/spacemit/bananapi_f3/ +F: configs/bananapi_f3_defconfig +F: doc/board/spacemit/bananapi_f3.rstboard/spacemit/bananapi_f3/Makefile new file +0
-0
board/spacemit/bananapi_f3/Makefile line 1
Quoted 1 line
board/spacemit/bananapi_f3/Makefile new file +1
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+
GPL-2.0-or-later
board/spacemit/bananapi_f3/board.c line 1
Quoted 11 lines
board/spacemit/bananapi_f3/Makefile new file +4
-0+# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y := board.oboard/spacemit/bananapi_f3/board.c new file +1
-0@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+
ditto
Quoted 14 lines
board/spacemit/bananapi_f3/board.c new file +8
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int board_init (void ) +{ +return 0 ; +}configs/bananapi_f3_defconfig new file +0
-0
configs/bananapi_f3_defconfig line 6
Quoted 6 lines
configs/bananapi_f3_defconfig new file +6
-0@@ -0,0 +1,20 @@ +CONFIG_RISCV=y +CONFIG_SYS_MALLOC_LEN=0x1000000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000000 +CONFIG_DEFAULT_DEVICE_TREE="k1-bananapi-f3"
The vendor SPL probably passes a device-tree to OpenSBI.
The BananaPi BPI-F3 is sold with different RAM sizes. SPL might already have determined the size and added the information to the device-tree.
Could we use that device-tree with CONFIG_OF_BOARD? We also need the memory reservation added by OpenSBI.
configs/bananapi_f3_defconfig line 17
Quoted 11 lines
configs/bananapi_f3_defconfig new file +11
-0+CONFIG_SYS_LOAD_ADDR=0x200000 +CONFIG_TARGET_BANANAPI_F3=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0xa000000 +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_SYS_CBSIZE=256 +CONFIG_SYS_PBSIZE=276 +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="bananapi_f3# "
Can we use the default prompt, please. This will make it easier to support nearly identical boards in future.
Best regards
Heinrich
Quoted 24 lines
configs/bananapi_f3_defconfig new file +3
-0+CONFIG_ENV_OVERWRITE=y +CONFIG_SYS_NS16550=y +CONFIG_SYS_NS16550_MEM32=yinclude/configs/bananapi_f3.h new file +15
-0@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +* +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <linux/serial_reg.h> + +#define CFG_SYS_SDRAM_BASE 0x0 +#define CFG_SYS_NS16550_IER UART_IER_UUE + +#endif /* __CONFIG_H */
Re: [PATCH 1/2] riscv: spacemit: bananapi_f3: initial support added
Quoted 112 lines · Heinrich Schuchardt <[email protected]> 于2024年7月14日周日 23:48写道:
Quoted 106 lines · Kongyang Liu
Add basic support for SpacemiT's Banana Pi F3 board
Signed-off-by Kongyang Liu <[email protected]>---
arch/riscv/Kconfig | 5 + arch/riscv/cpu/k1/Kconfig | 18 ++ arch/riscv/cpu/k1/Makefile | 6 + arch/riscv/cpu/k1/cpu.c | 9 + arch/riscv/cpu/k1/dram.c | 39 +++ arch/riscv/dts/Makefile | 1 + arch/riscv/dts/k1-bananapi-f3.dts | 20 ++ arch/riscv/dts/k1.dtsi | 375 +++++++++++++++++++++++++ board/spacemit/bananapi_f3/Kconfig | 25 ++ board/spacemit/bananapi_f3/MAINTAINERS | 6 + board/spacemit/bananapi_f3/Makefile | 5 + board/spacemit/bananapi_f3/board.c | 9 + configs/bananapi_f3_defconfig | 20 ++ include/configs/bananapi_f3.h | 15 + 14 files changed, 553 insertions(+)create mode 100644
arch/riscv/cpu/k1/Kconfigcreate mode 100644arch/riscv/cpu/k1/Makefilecreate mode 100644arch/riscv/cpu/k1/cpu.ccreate mode 100644arch/riscv/cpu/k1/dram.ccreate mode 100644arch/riscv/dts/k1-bananapi-f3.dtscreate mode 100644arch/riscv/dts/k1.dtsi
create mode 100644 board/spacemit/bananapi_f3/Kconfig create mode 100644 board/spacemit/bananapi_f3/MAINTAINERS create mode 100644 board/spacemit/bananapi_f3/Makefile create mode 100644board/spacemit/bananapi_f3/board.ccreate mode 100644 configs/bananapi_f3_defconfig create mode 100644include/configs/bananapi_f3.harch/riscv/Kconfig +5
-0@@ -11,6 +11,9 @@ choice config TARGET_ANDES_AE350 bool "Support Andes ae350" +config TARGET_BANANAPI_F3 + bool "Support BananaPi F3 Board" + config TARGET_MICROCHIP_ICICLE bool "Support Microchip PolarFire-SoC Icicle Board"@@ -88,6 +91,7 @@ source "board/sifive/unleashed/Kconfig" source "board/sifive/unmatched/Kconfig" source "board/sipeed/maix/Kconfig" source "board/sophgo/milkv_duo/Kconfig" +source "board/spacemit/bananapi_f3/Kconfig" source "board/starfive/visionfive2/Kconfig" source "board/thead/th1520_lpi4a/Kconfig" source "board/xilinx/mbv/Kconfig"@@ -99,6 +103,7 @@ source "arch/riscv/cpu/fu540/Kconfig" source "arch/riscv/cpu/fu740/Kconfig" source "arch/riscv/cpu/generic/Kconfig" source "arch/riscv/cpu/jh7110/Kconfig" +source "arch/riscv/cpu/k1/Kconfig" # architecture-specific options belowarch/riscv/cpu/k1/Kconfig new file +18
-0@@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2024, Kongyang Liu <[email protected]> + +config SPACEMIT_K1 + bool + select BINMAN + select ARCH_EARLY_INIT_R + select SYS_CACHE_SHIFT_6 + imply CPU + imply CPU_RISCV + imply RISCV_TIMER if (RISCV_SMODE || SPL_RISCV_SMODE) + imply RISCV_ACLINT if RISCV_MMODE + imply SPL_RISCV_ACLINT if SPL_RISCV_MMODE + imply CMD_CPU + imply SPL_CPU + imply SPL_OPENSBI + imply SPL_LOAD_FITarch/riscv/cpu/k1/Makefile new file +6
-0@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y += dram.o +obj-y += cpu.oarch/riscv/cpu/k1/cpu.c new file +0
-0arch/riscv/cpu/k1/cpu.c line 1
Quoted 1 line
arch/riscv/cpu/k1/cpu.c new file +1
-0@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ Thanks a lot for adding the board.
Quoted 2 lines
GPL-2.0-or-later, see https://spdx.org/licenses/GPL-2.0-or-later.html
Ok, I will fix it.
Quoted 96 lines
Quoted 14 lines
arch/riscv/cpu/k1/cpu.c new file +8
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int cleanup_before_linux (void ) +{ +return 0 ; +}arch/riscv/cpu/k1/dram.c new file +0
-0arch/riscv/cpu/k1/dram.c line 1
Quoted 1 line
arch/riscv/cpu/k1/dram.c new file +1
-0@@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0+ ditto
Quoted 78 lines
arch/riscv/cpu/k1/dram.c new file +38
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +#include <asm/global_data.h> +#include <config.h> +#include <linux/sizes.h> + +DECLARE_GLOBAL_DATA_PTR ; + +int dram_init (void ) +{ + gd->ram_base =CFG_SYS_SDRAM_BASE ; +/* TODO get ram size from ddr controller */ + gd->ram_size =SZ_4G ; +return 0 ; +} + +int dram_init_banksize (void ) +{ + gd->bd->bi_dram[0 ].start =CFG_SYS_SDRAM_BASE ; + gd->bd->bi_dram[0 ].size =min_t (phys_size_t, gd->ram_size,SZ_2G ); + +if (gd->ram_size >SZ_2G &&CONFIG_NR_DRAM_BANKS >1 ) { + gd->bd->bi_dram[1 ].start =0x100000000 ; + gd->bd->bi_dram[1 ].size = gd->ram_size -SZ_2G ; + } + +return 0 ; +} + +phys_addr_t board_get_usable_ram_top (phys_size_t total_size) +{ +if (gd->ram_size >SZ_2G ) +return SZ_2G ; + +return gd->ram_size; +}arch/riscv/dts/Makefile +1
-0@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0+ dtb-$(CONFIG_TARGET_ANDES_AE350) += ae350_32.dtb ae350_64.dtb +dtb-$(CONFIG_TARGET_BANANAPI_F3) += k1-bananapi-f3.dtb dtb-$(CONFIG_TARGET_MICROCHIP_ICICLE) += mpfs-icicle-kit.dtb dtb-$(CONFIG_TARGET_MILKV_DUO) += cv1800b-milkv-duo.dtb dtb-$(CONFIG_TARGET_QEMU_VIRT) += qemu-virt32.dtb qemu-virt64.dtbarch/riscv/dts/k1-bananapi-f3.dts new file +20
-0@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2024 Yangyu Chen <[email protected]> + */ + +#include "k1.dtsi" +#include "binman.dtsi" + +/ { + model = "Banana Pi BPI-F3"; + compatible = "bananapi,bpi-f3", "spacemit,k1"; + + chosen { + stdout-path = "serial0"; + }; +}; + +&uart0 { + status = "okay"; +};arch/riscv/dts/k1.dtsi new file +0
-0
Quoted 9 lines
arch/riscv/dts/k1.dtsi line 1
Quoted 5 lines
index 0000000000..b301f45fd5
arch/riscv/dts/k1.dtsi new file +1
-0@@ -0,0 +1,375 @@ +// SPDX-License-Identifier: GPL-2.0 OR MITElsewhere you use GPL-2.0-or-later. Any special reason to be more restrictive here?
This device tree is based on the device tree from the patch sent to the kernel. The reason for using this license is likely because the vendor's device tree also uses GPL-2.0 OR MIT.
Quoted 5 lines
Quoted 5 lines
arch/riscv/dts/k1.dtsi new file +5
-0+/* + * Copyright (C) 2024 Yangyu Chen <[email protected]> + */ + +/dts-v1/;
Quoted 9 lines
arch/riscv/dts/k1.dtsi line 11
Quoted 5 lines
arch/riscv/dts/k1.dtsi new file +5
-0+/ { + #address-cells = <2>; + #size-cells = <2>; + model = "SpacemiT K1"; + compatible = "spacemit,k1";According to the devicetree specification "a memory device node is required for all devicetrees".
I will add it.
Quoted 456 lines
Quoted 413 lines
arch/riscv/dts/k1.dtsi new file +364
-0+ + aliases { + serial0 = &uart0; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <24000000>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu_0>; + }; + core1 { + cpu = <&cpu_1>; + }; + core2 { + cpu = <&cpu_2>; + }; + core3 { + cpu = <&cpu_3>; + }; + }; + + cluster1 { + core0 { + cpu = <&cpu_4>; + }; + core1 { + cpu = <&cpu_5>; + }; + core2 { + cpu = <&cpu_6>; + }; + core3 { + cpu = <&cpu_7>; + }; + }; + }; + + cpu_0: cpu@0 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <0>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_1: cpu@1 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <1>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_2: cpu@2 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <2>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu2_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_3: cpu@3 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <3>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu3_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_4: cpu@4 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <4>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu4_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_5: cpu@5 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <5>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu5_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_6: cpu@6 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <6>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu6_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu_7: cpu@7 { + compatible = "spacemit,x60", "riscv"; + device_type = "cpu"; + reg = <7>; + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt"; + riscv,isa-base = "rv64i"; + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom", + "zicbop", "zicboz", "zicntr", "zicond", "zicsr", + "zifencei", "zihintpause", "zihpm", "zfh", "zba", + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt", + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt"; + riscv,cbom-block-size = <64>; + riscv,cbop-block-size = <64>; + riscv,cboz-block-size = <64>; + mmu-type = "riscv,sv39"; + + cpu7_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + dma-noncoherent; + ranges; + + uart0: serial@d4017000 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017000 0x0 0x100>; + interrupts = <42>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart2: serial@d4017100 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017100 0x0 0x100>; + interrupts = <44>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart3: serial@d4017200 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017200 0x0 0x100>; + interrupts = <45>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart4: serial@d4017300 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017300 0x0 0x100>; + interrupts = <46>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart5: serial@d4017400 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017400 0x0 0x100>; + interrupts = <47>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart6: serial@d4017500 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017500 0x0 0x100>; + interrupts = <48>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart7: serial@d4017600 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017600 0x0 0x100>; + interrupts = <49>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart8: serial@d4017700 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017700 0x0 0x100>; + interrupts = <50>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + uart9: serial@d4017800 { + compatible = "spacemit,k1-uart", "snps,dw-apb-uart"; + reg = <0x0 0xd4017800 0x0 0x100>; + interrupts = <51>; + clock-frequency = <14857000>; + reg-shift = <2>; + reg-io-width = <4>; + status = "disabled"; + }; + + plic: interrupt-controller@e0000000 { + compatible = "spacemit,k1-plic", "sifive,plic-1.0.0"; + reg = <0x0 0xe0000000 0x0 0x4000000>; + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>, + <&cpu4_intc 11>, <&cpu4_intc 9>, + <&cpu5_intc 11>, <&cpu5_intc 9>, + <&cpu6_intc 11>, <&cpu6_intc 9>, + <&cpu7_intc 11>, <&cpu7_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + riscv,ndev = <159>; + }; + + clint: timer@e4000000 { + compatible = "spacemit,k1-clint", "sifive,clint0"; + reg = <0x0 0xe4000000 0x0 0x10000>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>, + <&cpu4_intc 3>, <&cpu4_intc 7>, + <&cpu5_intc 3>, <&cpu5_intc 7>, + <&cpu6_intc 3>, <&cpu6_intc 7>, + <&cpu7_intc 3>, <&cpu7_intc 7>; + }; + }; +};board/spacemit/bananapi_f3/Kconfig new file +25
-0@@ -0,0 +1,25 @@ +if TARGET_BANANAPI_F3 + +config SYS_BOARD + default "bananapi_f3" + +config SYS_VENDOR + default "spacemit" + +config SYS_CPU + default "k1" + +config SYS_CONFIG_NAME + default "bananapi_f3" + +config TEXT_BASE + default 0x00200000 + +config SPL_OPENSBI_LOAD_ADDR + default 0x00000000 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select SPACEMIT_K1 + +endifboard/spacemit/bananapi_f3/MAINTAINERS new file +6
-0@@ -0,0 +1,6 @@ +BananaPi F3 +M: Kongyang Liu <[email protected]> +S: Maintained +F: board/spacemit/bananapi_f3/ +F: configs/bananapi_f3_defconfig +F: doc/board/spacemit/bananapi_f3.rstboard/spacemit/bananapi_f3/Makefile new file +0
-0board/spacemit/bananapi_f3/Makefile line 1
Quoted 1 line
board/spacemit/bananapi_f3/Makefile new file +1
-0@@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+GPL-2.0-or-later
board/spacemit/bananapi_f3/board.c line 1
Quoted 11 lines
board/spacemit/bananapi_f3/Makefile new file +4
-0+# +# Copyright (c) 2024, Kongyang Liu <[email protected]> + +obj-y := board.oboard/spacemit/bananapi_f3/board.c new file +1
-0@@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0+ ditto
Quoted 14 lines
board/spacemit/bananapi_f3/board.c new file +8
-0+/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +*/ + +int board_init (void ) +{ +return 0 ; +}configs/bananapi_f3_defconfig new file +0
-0configs/bananapi_f3_defconfig line 6
Quoted 6 lines
configs/bananapi_f3_defconfig new file +6
-0@@ -0,0 +1,20 @@ +CONFIG_RISCV=y +CONFIG_SYS_MALLOC_LEN=0x1000000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000000 +CONFIG_DEFAULT_DEVICE_TREE="k1-bananapi-f3"The vendor SPL probably passes a device-tree to OpenSBI.
Quoted 3 lines
The BananaPi BPI-F3 is sold with different RAM sizes. SPL might already have determined the size and added the information to the device-tree.
Currently, I have set the default memory size to 4GB in dram_init. This size can be adjusted later through the ddr controller.
Quoted 18 lines
Could we use that device-tree with
CONFIG_OF_BOARD? We also need the memory reservation added by OpenSBI.configs/bananapi_f3_defconfig line 17
Quoted 11 lines
configs/bananapi_f3_defconfig new file +11
-0+CONFIG_SYS_LOAD_ADDR=0x200000 +CONFIG_TARGET_BANANAPI_F3=y +CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0xa000000 +CONFIG_SUPPORT_RAW_INITRD=y +CONFIG_SYS_CBSIZE=256 +CONFIG_SYS_PBSIZE=276 +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="bananapi_f3# "Can we use the default prompt, please. This will make it easier to support nearly identical boards in future.
I will fix it.
Best regards
Kongyang Liu
Quoted 29 lines
Best regards
Heinrich
Quoted 24 lines
configs/bananapi_f3_defconfig new file +3
-0+CONFIG_ENV_OVERWRITE=y +CONFIG_SYS_NS16550=y +CONFIG_SYS_NS16550_MEM32=yinclude/configs/bananapi_f3.h new file +15
-0@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (c) 2024, Kongyang Liu <[email protected]> +* +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <linux/serial_reg.h> + +#define CFG_SYS_SDRAM_BASE 0x0 +#define CFG_SYS_NS16550_IER UART_IER_UUE + +#endif /* __CONFIG_H */
PATCH 2/2 doc: spacemit: bananapi_f3: document Banana Pi F3 board
In reply to Kongyang LiuAdd document for Banana Pi F3 board which based on SpacemiT's K1 SoC.
---
doc/board/index.rst | 1 + doc/board/spacemit/bananapi_f3.rst | 78 ++++++++++++++++++++++++++++++ doc/board/spacemit/index.rst | 8 +++ 3 files changed, 87 insertions(+) create mode 100644 doc/board/spacemit/bananapi_f3.rst create mode 100644 doc/board/spacemit/index.rst
doc/board/index.rst +1 -0
@@ -51,6 +51,7 @@ Board-specific doc sipeed/index socionext/index sophgo/index + spacemit/index st/index starfive/index ste/index
doc/board/spacemit/bananapi_f3.rst new file +78 -0
78 lines not on this page · raw message
doc/board/spacemit/index.rst new file +8 -0
@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +SpacemiT +======== +.. toctree:: + :maxdepth: 1 + + bananapi_f3
Signature · 1 line
2.41.0
Re: [PATCH 2/2] doc: spacemit: bananapi_f3: document Banana Pi F3 board
Quoted 59 lines · Kongyang Liu
Add document for Banana Pi F3 board which based on SpacemiT's K1 SoC.
Signed-off-by Kongyang Liu <[email protected]>---
doc/board/index.rst | 1 + doc/board/spacemit/bananapi_f3.rst | 78 ++++++++++++++++++++++++++++++ doc/board/spacemit/index.rst | 8 +++ 3 files changed, 87 insertions(+)create mode 100644
doc/board/spacemit/bananapi_f3.rstcreate mode 100644doc/board/spacemit/index.rstdoc/board/index.rst +1
-0@@ -51,6 +51,7 @@ Board-specific doc sipeed/index socionext/index sophgo/index + spacemit/index st/index starfive/index ste/indexdoc/board/spacemit/bananapi_f3.rst new file +29
-0@@ -0,0 +1,78 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Banana Pi F3 +============ + +About This +---------- +Banana Pi F3 board is a industrial grade RISC-V development board, it +design with SpacemiT K1 8 core RISC-V chip, CPU integrates 2.0 TOPs AI +computing power. 4G DDR and 16G eMMC onboard.2x GbE Ethernet prot, 4x USB +3.0 and PCIe for M.2 interface, support HDMI and Dual MIPI-CSI Camera. + +Building +~~~~~~~~ +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: console + + export CROSS_COMPILE=<riscv64 toolchain prefix> + +3. Before building U-Boot, OpenSBI should be built first. OpenSBI can be +built for SpacemiT K1 SoC as below: + +.. code-block:: console + + git clone https://github.com/cyyself/opensbi -b k1-opensbi + cd opensbi + make PLATFORM=generic
doc/board/spacemit/bananapi_f3.rst line 39
Quoted 10 lines
doc/board/spacemit/bananapi_f3.rst new file +10
-0+ +4. Then build U-Boot as following: + +.. code-block:: console + + cd <U-Boot-dir> + make bananapi_f3_defconfig + make OPENSBI=<OpenSBI-dir>/build/platform/generic/firmware/fw_dynamic.bin + +This will generate u-boot.itb
Thanks a lot for the board documentation.
Could you, please, describe how to install the u-boot.itb.
To where should it be copied?
Does it need to be signed to be accepted by the vendor SPL?
Best regards
Heinrich
Quoted 53 lines
doc/board/spacemit/bananapi_f3.rst new file +39
-0+ +Booting +~~~~~~~ +Currently, we use a modified vendor's U-Boot SPL to load a FIT image that +includes OpenSBI and U-Boot. Fully describing how to boot into U-Boot is a +challenging task. And the booting method will be added after the SPL +support is available. + +Sample boot log from Banana Pi F3 board +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +.. code-block:: none + + U-Boot 2024.07-00686-g608f2d51760c (Jul 08 2024 - 14:53:51 +0800) + + DRAM: 4 GiB + Core: 18 devices, 7 uclasses, devicetree: separate + Loading Environment from nowhere... OK + In: serial@d4017000 + Out: serial@d4017000 + Err: serial@d4017000 + Net: No ethernet found. + bananapi_f3# cpu detail + 0: cpu@0 spacemit,x60 + ID = 0, freq = 0 Hz: MMU + 1: cpu@1 spacemit,x60 + ID = 1, freq = 0 Hz: MMU + 2: cpu@2 spacemit,x60 + ID = 2, freq = 0 Hz: MMU + 3: cpu@3 spacemit,x60 + ID = 3, freq = 0 Hz: MMU + 4: cpu@4 spacemit,x60 + ID = 4, freq = 0 Hz: MMU + 5: cpu@5 spacemit,x60 + ID = 5, freq = 0 Hz: MMU + 6: cpu@6 spacemit,x60 + ID = 6, freq = 0 Hz: MMU + 7: cpu@7 spacemit,x60 + ID = 7, freq = 0 Hz: MMU + bananapi_f3#doc/board/spacemit/index.rst new file +8
-0@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +SpacemiT +======== +.. toctree:: + :maxdepth: 1 + + bananapi_f3
Re: [PATCH 2/2] doc: spacemit: bananapi_f3: document Banana Pi F3 board
Quoted 74 lines · Heinrich Schuchardt <[email protected]> 于2024年7月14日周日 23:19写道:
Quoted 59 lines · Kongyang Liu
Add document for Banana Pi F3 board which based on SpacemiT's K1 SoC.
Signed-off-by Kongyang Liu <[email protected]>---
doc/board/index.rst | 1 + doc/board/spacemit/bananapi_f3.rst | 78 ++++++++++++++++++++++++++++++ doc/board/spacemit/index.rst | 8 +++ 3 files changed, 87 insertions(+)create mode 100644
doc/board/spacemit/bananapi_f3.rstcreate mode 100644doc/board/spacemit/index.rstdoc/board/index.rst +1
-0@@ -51,6 +51,7 @@ Board-specific doc sipeed/index socionext/index sophgo/index + spacemit/index st/index starfive/index ste/indexdoc/board/spacemit/bananapi_f3.rst new file +29
-0@@ -0,0 +1,78 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Banana Pi F3 +============ + +About This +---------- +Banana Pi F3 board is a industrial grade RISC-V development board, it +design with SpacemiT K1 8 core RISC-V chip, CPU integrates 2.0 TOPs AI +computing power. 4G DDR and 16G eMMC onboard.2x GbE Ethernet prot, 4x USB +3.0 and PCIe for M.2 interface, support HDMI and Dual MIPI-CSI Camera. + +Building +~~~~~~~~ +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: console + + export CROSS_COMPILE=<riscv64 toolchain prefix> + +3. Before building U-Boot, OpenSBI should be built first. OpenSBI can be +built for SpacemiT K1 SoC as below: + +.. code-block:: console + + git clone https://github.com/cyyself/opensbi -b k1-opensbi + cd opensbi + make PLATFORM=genericdoc/board/spacemit/bananapi_f3.rst line 39
Quoted 10 lines
doc/board/spacemit/bananapi_f3.rst new file +10
-0+ +4. Then build U-Boot as following: + +.. code-block:: console + + cd <U-Boot-dir> + make bananapi_f3_defconfig + make OPENSBI=<OpenSBI-dir>/build/platform/generic/firmware/fw_dynamic.bin + +This will generate u-boot.itbThanks a lot for the board documentation.
Quoted 5 lines
Could you, please, describe how to install the u-boot.itb.
To where should it be copied?
Does it need to be signed to be accepted by the vendor SPL?
In the vendor's U-Boot SPL, OpenSBI and U-Boot are loaded separately. From my observation, U-Boot seems to prefer loading a FIT image that includes both OpenSBI and U-Boot. Therefore, I modified this part to allow them to be loaded together. The modified code might be somewhat messy because I just made it work.
As a result, it is currently difficult to describe how to boot into U-Boot. Perhaps I can improve the documentation after U-Boot SPL is available for Banana Pi F3.
Best regards
Kongyang Liu
Quoted 58 lines
Best regards
Heinrich
Quoted 53 lines
doc/board/spacemit/bananapi_f3.rst new file +39
-0+ +Booting +~~~~~~~ +Currently, we use a modified vendor's U-Boot SPL to load a FIT image that +includes OpenSBI and U-Boot. Fully describing how to boot into U-Boot is a +challenging task. And the booting method will be added after the SPL +support is available. + +Sample boot log from Banana Pi F3 board +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +.. code-block:: none + + U-Boot 2024.07-00686-g608f2d51760c (Jul 08 2024 - 14:53:51 +0800) + + DRAM: 4 GiB + Core: 18 devices, 7 uclasses, devicetree: separate + Loading Environment from nowhere... OK + In: serial@d4017000 + Out: serial@d4017000 + Err: serial@d4017000 + Net: No ethernet found. + bananapi_f3# cpu detail + 0: cpu@0 spacemit,x60 + ID = 0, freq = 0 Hz: MMU + 1: cpu@1 spacemit,x60 + ID = 1, freq = 0 Hz: MMU + 2: cpu@2 spacemit,x60 + ID = 2, freq = 0 Hz: MMU + 3: cpu@3 spacemit,x60 + ID = 3, freq = 0 Hz: MMU + 4: cpu@4 spacemit,x60 + ID = 4, freq = 0 Hz: MMU + 5: cpu@5 spacemit,x60 + ID = 5, freq = 0 Hz: MMU + 6: cpu@6 spacemit,x60 + ID = 6, freq = 0 Hz: MMU + 7: cpu@7 spacemit,x60 + ID = 7, freq = 0 Hz: MMU + bananapi_f3#doc/board/spacemit/index.rst new file +8
-0@@ -0,0 +1,8 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +SpacemiT +======== +.. toctree:: + :maxdepth: 1 + + bananapi_f3