wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
PATCH v2 1/5 wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
From: Ping-Ke Shih <[email protected]>
Radiocommunications Regulations (General User Radio Licence for Short Range Devices) Notice 2022 listed spectrum:
2400.0000 - 2483.5000
* e.i.r.p. 6 dBW (36 dBm)
5150.0000 - 5350.0000
* the maximum power is 0 dBW (1 W) e.i.r.p. and
the maximum permitted power spectral density is -13 dBW/MHz (17 dBm/Hz, 50 mW/MHz) e.i.r.p.
* 5250 - 5350 MHz, If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value shall be reduced by 3 dB.
5470.0000 - 5725.0000
* 5470 - 5725 MHz, The maximum power is 0 dBW (1 W) e.i.r.p. and the maximum permitted power spectral density is -13 dBW/MHz (50 mW/MHz) e.i.r.p. If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value must be reduced by 3 dB.
* Then 27 dBm is adopted (0 dBW - minus 3 dB due to lack of TPC)
5725.0000 - 5875.0000
* e.i.r.p. 6 dBW (36 dBm)
5925.0000 - 6425.0000
* the maximum power is -6 dBW (24 dBm, 250 mW ) e.i.r.p. and the maximum permitted power spectral density is -19 dBW/MHz (11 dBm/MHz, 12.6 mW/MHz) e.i.r.p. for low power devices. Only be used indoors.
* the maximum power is -16 dBW (14 dBm, 25 mW ) e.i.r.p. and the maximum permitted power spectral density is -29 dBW/MHz (1 dBm/MHz, 1.26 mW/MHz) e.i.r.p. for very low power devices. Very Low Power applications.
57000.0000 - 71000.0000
* for devices transmitting at 10 dBW e.i.r.p or less,
the power spectral density must not exceed -7 dBW/MHz e.i.r.p. and the maximum transmit power must not exceed -3 dBW at the antenna port or ports.
* for devices transmitting greater than 10 dBW e.i.r.p., the power spectral density shall not exceed 8 dBW/MHz e.i.r.p and antennas with a gain greater than 30 dBi shall be used.
[1] https://gazette.govt.nz/notice/id/2022-go3100
---
v2:
- correct 2400 - 2483.5 to 6dBW
- correct 5470 - 5730 to 27dBm
- correct 5725 - 5875 to 6dBW
--- db.txt | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-)
db.txt +9 -5
@@ -1416,12 +1416,16 @@ country NP: DFS-JP (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5735 - 5835 @ 80), (20) +# Source: +# https://gazette.govt.nz/notice/id/2022-go3100 country NZ: DFS-ETSI - (2402 - 2482 @ 40), (30) - (5170 - 5250 @ 80), (17), AUTO-BW - (5250 - 5330 @ 80), (24), DFS, AUTO-BW - (5490 - 5730 @ 160), (24), DFS - (5735 - 5835 @ 80), (30) + (2400 - 2483.5 @ 40), (36) + (5150 - 5250 @ 80), (30), AUTO-BW + (5250 - 5350 @ 80), (27), DFS, AUTO-BW + (5470 - 5730 @ 160), (27), DFS + (5725 - 5875 @ 80), (36) + (5925 - 6425 @ 320), (24), NO-OUTDOOR + (57000 - 71000 @ 2160), (40) country OM: DFS-ETSI (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
PATCH v2 2/5 wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
From: Ping-Ke Shih <[email protected]>
Ministerial Resolution -2021-MTC/01 decided
For the band 5925-7125 MHz, low power indoor case of use.
- access point
maximum EIRP: 30 dBm
Limited power spectral density: 5 dBm / MHz
- user devices
maximum EIRP: 24 dBm
Limited power spectral density: -1 dBm / MHz
With minimum bandwidth 20MHz and PSD -1 dBm/MHz, 12 dBm is adopted.
---
v2:
- explain how induce how we induce 12 dBm from PSD -1 dBm/MHz in commit message
--- db.txt | 3 +++ 1 file changed, 3 insertions(+)
db.txt +3 -0
@@ -1443,12 +1443,15 @@ country PA: DFS-FCC (5725 - 5850 @ 80), (36) (57000 - 64000 @ 2160), (43) +# Source: +# https://cdn.www.gob.pe/uploads/document/file/1861732/Resoluci%C3%B3n%20Ministerial%20nro%20373-2021-MTC/01.pdf country PE: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 80), (17), AUTO-BW (5250 - 5330 @ 80), (24), DFS, AUTO-BW (5490 - 5730 @ 160), (24), DFS (5735 - 5835 @ 80), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country PF: DFS-ETSI (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
PATCH v2 3/5 wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
The General Superintendency of Electricity and Telecommunications Makes Knowledge to the General issued resolution No. T-0408-2023.
Free use within the entire band for WLAN (WiFi) application, from 5925 MHz to 7125 MHz, must have following technical and operation conditions:
- access point
* P.I.R.E 30 dBm
* spectral density of P.I.R.E. 5 dBm/Mhz
- client
* P.I.R.E 24 dBm
* spectral density of P.I.R.E. -1 dBm/Mhz
- Indoor use only permitted
With minimum bandwidth 20MHz and PSD -1 dBm/MHz, 12 dBm is adopted.
[1] https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/
---
v2:
- explain how induce how we induce 12 dBm from PSD -1 dBm/MHz in commit message
--- db.txt | 3 +++ 1 file changed, 3 insertions(+)
db.txt +3 -0
@@ -1736,11 +1736,14 @@ country SR: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/ country SV: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 20), (17) (5250 - 5330 @ 20), (23), DFS (5735 - 5835 @ 20), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country SY: (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
PATCH v2 4/5 wireless-regdb: Update regulatory info for Togo (TG) for 2022
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
Republic ToGolaise released Decision N 226/ARCEP/DG/22.
2400-2483.5 MHz
- EIRP 100 mW and 10 mW/MHz density
5150-5350 MHz
- EIRP 200 mW
- If TPC is not used, must be reduced by 3 dB
5470-5850 MHz
- EIRP 1W
- If TPC is not used, must be reduced by 3 dB
5925-6425 MHz
- LPI
* EIRP 23 dBm (200 mW)
* EIRP density 10 dBm/MHz
(Reference [1] suggest this as -10 dBm/MHz, but this would be an error,
becase PSD of LPI should not be lower than VLP.)
* Use limited to indoor
- VLP
* EIRP 14 dBm (25 mW)
* EIRP density -1 dBm/MHz
57-66 GHz
- EIRP 40 dBm and 13 dBm/MHz density
---
v2:
- in commit message, describe typo that 5925-6425 LPI should be EIRP density 10 dBm/MHz. Otherwise, PSD for LPI is lower than VLP.
- add DFS for all bands
- not split 5150 - 5350 band, and set bandwidth to 80 MHz
- set bandwidth 160 MHz for 5470 - 5850
--- db.txt | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)
db.txt +7 -4
@@ -1763,11 +1763,14 @@ country TD: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://arcep.tg/wp-content/uploads/2022/12/Decision-226-22-Determinant-les-categories-et-conditions-techniques-dexploitation-des-appareils-de-faible-puissance-et-de-faible-portee.pdf country TG: DFS-ETSI - (2402 - 2482 @ 40), (20) - (5170 - 5250 @ 40), (20) - (5250 - 5330 @ 40), (20), DFS - (5490 - 5710 @ 40), (27), DFS + (2400 - 2483.5 @ 40), (100 mW), DFS + (5150 - 5350 @ 80), (20), DFS + (5470 - 5850 @ 160), (27), DFS + (5925 - 6425 @ 320), (23), DFS, NO-OUTDOOR + (57000 - 66000 @2160), (40), DFS # Source: # https://ratchakitcha.soc.go.th/documents/140D100S0000000004000.pdf
Signature · 1 line
2.25.1
Chen-Yu Tsai
AppliedRe: [PATCH v2 4/5] wireless-regdb: Update regulatory info for Togo (TG) for 2022
Quoted 26 lines · Ping-Ke Shih
From: Ping-Ke Shih <[email protected]>
Republic ToGolaise released Decision N 226/ARCEP/DG/22.
2400-2483.5 MHz
- EIRP 100 mW and 10 mW/MHz density
5150-5350 MHz
- EIRP 200 mW
- If TPC is not used, must be reduced by 3 dB
5470-5850 MHz
- EIRP 1W
- If TPC is not used, must be reduced by 3 dB
5925-6425 MHz
- LPI
* EIRP 23 dBm (200 mW)
* EIRP density 10 dBm/MHz
(Reference [1] suggest this as -10 dBm/MHz, but this would be an error,
becase PSD of LPI should not be lower than VLP.)
* Use limited to indoor
- VLP
* EIRP 14 dBm (25 mW)
* EIRP density -1 dBm/MHz
57-66 GHz
- EIRP 40 dBm and 13 dBm/MHz density
Quoted 7 lines
Signed-off-by Ping-Ke Shih <[email protected]>---
v2:
- in commit message, describe typo that 5925-6425 LPI should be EIRP density 10 dBm/MHz. Otherwise, PSD for LPI is lower than VLP.
I applied this patch for now. But could you reach out to the ARCEP to notify them of this, and ask for clarification?
Thanks
ChenYu
Quoted 33 lines
- add DFS for all bands
- not split 5150 - 5350 band, and set bandwidth to 80 MHz
- set bandwidth 160 MHz for 5470 - 5850--- db.txt | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-)db.txt +7
-5@@ -1763,11 +1763,14 @@ country TD: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://arcep.tg/wp-content/uploads/2022/12/Decision-226-22-Determinant-les-categories-et-conditions-techniques-dexploitation-des-appareils-de-faible-puissance-et-de-faible-portee.pdf country TG: DFS-ETSI - (2402 - 2482 @ 40), (20) - (5170 - 5250 @ 40), (20) - (5250 - 5330 @ 40), (20), DFS - (5490 - 5710 @ 40), (27), DFS + (2400 - 2483.5 @ 40), (100 mW), DFS + (5150 - 5350 @ 80), (20), DFS + (5470 - 5850 @ 160), (27), DFS + (5925 - 6425 @ 320), (23), DFS, NO-OUTDOOR + (57000 - 66000 @2160), (40), DFS # Source: # https://ratchakitcha.soc.go.th/documents/140D100S0000000004000.pdf --2.25.1
Re: [PATCH v2 4/5] wireless-regdb: Update regulatory info for Togo (TG) for 2022
Quoted 7 lines · Chen-Yu Tsai
Quoted 4 lines
v2:
- in commit message, describe typo that 5925-6425 LPI should be EIRP density 10 dBm/MHz. Otherwise, PSD for LPI is lower than VLP.I applied this patch for now. But could you reach out to the ARCEP to notify them of this, and ask for clarification?
Sure. I will contact ARCEP.
PATCH v2 5/5 wireless-regdb: Add regulatory info for Namibia (NA) for 2023
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
COMMUNICATIONS REGULATORY AUTHORITY OF NAMIBIA released NOTICE IN TERMS OF THE REGULATIONS REGARDING THE SUBMISSIONS OF INTERCONNECTION AGREEMENTS AND TARIFFS on 3 April 2023 [1].
* 2400-2483.5 MHz
100 mW e.i.r.p.
* 5150-5350 MHz
200 mW mean e.i.r.p.
Restricted to indoor use
The maximum mean e.i.r.p. density shall be limited to 10 mW/MHz (ETSI [2]: 200mW (23dBm) -3 dBm to be 20 dBm; DFS 5250-5350)
* 5470-5725 MHz
250 mW e.i.r.p.
Indoor as well as outdoor use allowed.
The maximum mean e.i.r.p. density shall be limited to 50 mW/MHz (ETSI [2]: 250mW (24dBm) -3 dBm to be 21 dBm; DFS)
* 5725-5875 MHz
PTP/PTMP: max mean e.i.r.p = 4 W
Mesh/AP-MP: max mean e.i.r.p = 2 W
(ETSI [3]: The FWA device shall have the capability to reduce the
operating mean EIRP level to a level not exceeding 24 dBm for ChS = 20 MHz and 21 dBm for ChS = 10 MHz. 24 dBm is adopted; DFS)
* 5925-6425 MHz
- 23 dBm (200mW) mean e.i.r.p
Restricted to indoor use only.
Mean e.i.r.p density for in-band emissions = 10 dBm/MHz
- 14 dBm (25) e.i.r.p mW
Very Low Power (VLP) indoor outdoor use. Maximum mean e.i.r.p. for inband emissions = 1 dBm/MHz
* 57-66 GHz
40 dBm (10W) mean e.i.r.p
23 dBm/MHz e.i.r.p. density
Indoor use only
The EN 301 893 [2] specifies reduced power limit of 23 and 27 dBm for 5150-5350 MHz and 5470-5725 MHz respectively for devices that don't implement TPC. Also reduced TPC requires being able to reduce TX power by up to 3 dB. The DFS applicable frequency range are 5250-5350 MHz and 5470-5725 MHz.
[1] https://www.cran.na/yglilidy/2023/04/GG-8060-dated-3-April-2023.pdf
[2] EN 301 893 https://www.etsi.org/deliver/etsi_en/301800_301899/301893/02.01.01_60/en_301893v020101p.pdf
[3] EN 302 502 https://www.etsi.org/deliver/etsi_en/302500_302599/302502/02.01.01_60/en_302502v020101p.pdf
---
v2:
- join to the same patchset
- 5150-5350 and 5470-5725 only reduce 3dB due to TPC
- 5725-5875 requires DFS
- fix wording in commit message:
* '5725-5 875 MHz' --> '5725-5875 MHz'
* '10 dBM/MHz' --> '10 dBm/MHz'
* 'Maximum meand e.i.r.p.' --> 'Maximum mean e.i.r.p' (drop extra 'd')
--- db.txt | 11 +++++++++++ 1 file changed, 11 insertions(+)
db.txt +11 -0
@@ -1355,6 +1355,17 @@ country MY: DFS-FCC (5735 - 5835 @ 80), (1000 mW) (5925 - 6425 @ 320), (200 mW), NO-OUTDOOR +# Source: +# https://www.cran.na/yglilidy/2023/04/GG-8060-dated-3-April-2023.pdf +country NA: DFS-ETSI + (2400 - 2483.5 @ 40), (100 mW) + (5150 - 5250 @ 80), (20), AUTO-BW, NO-OUTDOOR + (5250 - 5350 @ 80), (20), DFS, AUTO-BW, NO-OUTDOOR + (5470 - 5725 @ 160), (21), DFS + (5725 - 5875 @ 80), (24), DFS + (5925 - 6425 @ 320), (23), NO-OUTDOOR + (57000 - 66000 @ 2160), (40), NO-OUTDOOR + country NG: DFS-ETSI (2402 - 2482 @ 40), (20) (5250 - 5330 @ 80), (30), DFS
Signature · 1 line
2.25.1
Chen-Yu Tsai
AppliedQuoted 6 lines · Ping-Ke Shih
Radiocommunications Regulations (General User Radio Licence for Short Range Devices) Notice 2022 listed spectrum:
2400.0000 - 2483.5000
* e.i.r.p. 6 dBW (36 dBm)
Quoted 8 lines
5150.0000 - 5350.0000
* the maximum power is 0 dBW (1 W) e.i.r.p. and
the maximum permitted power spectral density is -13 dBW/MHz (17 dBm/Hz, 50 mW/MHz) e.i.r.p.
* 5250 - 5350 MHz, If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value shall be reduced by 3 dB.[...]
Applied to master in wens/wireless-regdb.git, thanks!
[1/5] wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
https://git.kernel.org/wens/wireless-regdb/c/bad398523d73 [2/5] wireless-regdb: Update regulatory info for Peru (PE) on 6GHz https://git.kernel.org/wens/wireless-regdb/c/58575b4cc911 [3/5] wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz https://git.kernel.org/wens/wireless-regdb/c/983f55149d7f [4/5] wireless-regdb: Update regulatory info for Togo (TG) for 2022 https://git.kernel.org/wens/wireless-regdb/c/aad0c26a1612 [5/5] wireless-regdb: Add regulatory info for Namibia (NA) for 2023 https://git.kernel.org/wens/wireless-regdb/c/218d1460e046
Best regards,
Signature · 1 line
Chen-Yu Tsai <[email protected]>