Skip to contentSkip to conversation

Add Anbernic RG35XX-2024

PATCH Superseded Chris Morgan 2 participants 12 messages Aug 19, 2024 – Aug 20, 2024

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover Add Anbernic RG35XX-2024

From: Chris Morgan <[email protected]>

Add support for the Anbernic RG35XX-2024.

This device is a handheld gaming console (series) based around the Anbernic H700 SoC. It comes with 1GB of RAM and multiple face buttons for input.

Add support for the simplest model for now, and then iterate later to add board detection logic, support the entire device lineup, and move to using the mainline device tree.

Changes since V1:
- Removed DDR3 and LPDDR3 patches from Jernej Skrabec, as they could not be tested by me and were not required to bring up this device.
- Changed the default TPR6 parameter based on a suggestion from Mikhail Kalashnikov.
- Cherry picked 2 commits from linux-next and converted devicetree to upstream.

Chris Morgan (4):
arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes
sunxi: Correct TPR6 parameter for H616 DRAM driver
arm64: dts: allwinner: h616: Change RG35XX Series from r_rsb to r_i2c
sunxi: Add support for Anbernic RG35XX-2024

Jernej Skrabec (5):
sunxi: H616: dram: LPDDR4: adjust settings
sunxi: H616: DRAM: Add alternative pin mapping
sunxi: H616: DRAM: Adjust configuration procedure
sunxi: H616: DRAM: Adjust size scan procedure
sunxi: H616: dram: Update mbus priorities

 arch/arm/mach-sunxi/Kconfig                   |   2 +-
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 174 ++++++++++++------
 .../dram_timings/h616_lpddr4_2133.c           |   2 +-
 board/sunxi/MAINTAINERS                       |   5 +
 configs/anbernic_rg35xx_h700_defconfig        |  52 ++++++
 .../src/arm64/allwinner/sun50i-h616.dtsi      |   2 +
 .../sun50i-h700-anbernic-rg35xx-2024.dts      |   6 +-
 7 files changed, 179 insertions(+), 64 deletions(-)
 create mode 100644 configs/anbernic_rg35xx_h700_defconfig
Signature · 1 line
2.34.1
#1 lore raw

PATCH v2 1/9 sunxi: H616: dram: LPDDR4: adjust settings

From: Jernej Skrabec <[email protected]>

Adjust H616 LPDDR4 DRAM settings to be in line with vendor driver.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 33 +++++++++++++------
 .../dram_timings/h616_lpddr4_2133.c           |  2 +-
 2 files changed, 24 insertions(+), 11 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +23 -10
index 37c139e0ee..5be2887a06 100644
@@ -293,14 +293,22 @@ static void mctl_phy_configure_odt(const struct dram_para *para)
 	dmb();
 }
 
-static bool mctl_phy_write_leveling(const struct dram_config *config)
+static bool mctl_phy_write_leveling(const struct dram_para *para,
+				    const struct dram_config *config)
 {
 	bool result = true;
 	u32 val;
 
 	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 8, 0xc0, 0x80);
-	writel(4, SUNXI_DRAM_PHY0_BASE + 0xc);
-	writel(0x40, SUNXI_DRAM_PHY0_BASE + 0x10);
+
+	if (para->type == SUNXI_DRAM_TYPE_LPDDR4) {
+		/* MR2 value */
+		writel(0x1b, SUNXI_DRAM_PHY0_BASE + 0xc);
+		writel(0, SUNXI_DRAM_PHY0_BASE + 0x10);
+	} else {
+		writel(4, SUNXI_DRAM_PHY0_BASE + 0xc);
+		writel(0x40, SUNXI_DRAM_PHY0_BASE + 0x10);
+	}
 
 	setbits_le32(SUNXI_DRAM_PHY0_BASE + 8, 4);
 
@@ -859,9 +867,9 @@ static void mctl_phy_ca_bit_delay_compensation(const struct dram_para *para,
 		}
 		break;
 	case SUNXI_DRAM_TYPE_LPDDR4:
-		if (para->tpr2 & 1) {
-			writel(val, SUNXI_DRAM_PHY0_BASE + 0x788);
-		} else {
+		writel(val, SUNXI_DRAM_PHY0_BASE + 0x788);
+		if (config->ranks == 2) {
+			val = (para->tpr10 >> 11) & 0x1e;
 			writel(val, SUNXI_DRAM_PHY0_BASE + 0x794);
 		};
 		break;
@@ -1080,19 +1088,27 @@ static bool mctl_phy_init(const struct dram_para *para,
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xb04, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xc72, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xe09, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0x1624, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 		break;
 	case SUNXI_DRAM_TYPE_DDR4:
@@ -1108,7 +1124,7 @@ static bool mctl_phy_init(const struct dram_para *para,
 
 	if (para->tpr10 & TPR10_WRITE_LEVELING) {
 		for (i = 0; i < 5; i++)
-			if (mctl_phy_write_leveling(config))
+			if (mctl_phy_write_leveling(para, config))
 				break;
 		if (i == 5) {
 			debug("write leveling failed!\n");
@@ -1234,9 +1250,6 @@ static bool mctl_ctrl_init(const struct dram_para *para,
 	setbits_le32(&mctl_ctl->unk_0x3180, BIT(31) | BIT(30));
 	setbits_le32(&mctl_ctl->unk_0x4180, BIT(31) | BIT(30));
 
-	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
-		setbits_le32(&mctl_ctl->dbictl, 0x1);
-
 	setbits_le32(&mctl_ctl->rfshctl3, BIT(0));
 	clrbits_le32(&mctl_ctl->dfimisc, BIT(0));
 
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c +1 -1
index e6446b9180..6f5c4acbd6 100644
@@ -23,7 +23,7 @@ void mctl_set_timing_params(const struct dram_para *para)
 	u8 trcd		= max(ns_to_t(18), 2);
 	u8 trc		= ns_to_t(65);
 	u8 txp		= max(ns_to_t(8), 2);
-	u8 trtp		= max(ns_to_t(8), 4);
+	u8 trtp		= 4;
 	u8 trp		= ns_to_t(21);
 	u8 tras		= ns_to_t(42);
 	u16 trefi	= ns_to_t(3904) / 32;
Signature · 1 line
2.34.1
#2 lore raw

PATCH v2 2/9 sunxi: H616: DRAM: Add alternative pin mapping

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

It seems that different dies need different PHY pin mapping. Select alternatives based on "bond ID".

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 59 +++++++++++++++++++-------
 1 file changed, 44 insertions(+), 15 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +44 -15
index 5be2887a06..dfaa270d96 100644
@@ -225,22 +225,43 @@ static void mctl_set_addrmap(const struct dram_config *config)
 	mctl_ctl->addrmap[8] = 0x3F3F;
 }
 
-static const u8 phy_init[] = {
+static const u8 phy_addr_maps[2][27] = {
 #ifdef CONFIG_SUNXI_DRAM_H616_DDR3_1333
-	0x07, 0x0b, 0x02, 0x16, 0x0d, 0x0e, 0x14, 0x19,
-	0x0a, 0x15, 0x03, 0x13, 0x04, 0x0c, 0x10, 0x06,
-	0x0f, 0x11, 0x1a, 0x01, 0x12, 0x17, 0x00, 0x08,
-	0x09, 0x05, 0x18
+	{
+		0x07, 0x0b, 0x02, 0x16, 0x0d, 0x0e, 0x14, 0x19,
+		0x0a, 0x15, 0x03, 0x13, 0x04, 0x0c, 0x10, 0x06,
+		0x0f, 0x11, 0x1a, 0x01, 0x12, 0x17, 0x00, 0x08,
+		0x09, 0x05, 0x18
+	}, {
+		0x08, 0x02, 0x12, 0x05, 0x15, 0x17, 0x18, 0x0b,
+		0x14, 0x07, 0x04, 0x13, 0x0c, 0x00, 0x16, 0x1a,
+		0x0a, 0x11, 0x03, 0x10, 0x0e, 0x01, 0x0d, 0x19,
+		0x06, 0x09, 0x0f
+	}
 #elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR3)
-	0x18, 0x06, 0x00, 0x05, 0x04, 0x03, 0x09, 0x02,
-	0x08, 0x01, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
-	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
-	0x17, 0x19, 0x1a
+	{
+		0x18, 0x06, 0x00, 0x05, 0x04, 0x03, 0x09, 0x02,
+		0x08, 0x01, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
+		0x17, 0x19, 0x1a
+	}, {
+		0x18, 0x00, 0x04, 0x09, 0x06, 0x05, 0x02, 0x19,
+		0x17, 0x03, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
+		0x08, 0x01, 0x1a
+	}
 #elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR4)
-	0x02, 0x00, 0x17, 0x05, 0x04, 0x19, 0x06, 0x07,
-	0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
-	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
-	0x18, 0x03, 0x1a
+	{
+		0x02, 0x00, 0x17, 0x05, 0x04, 0x19, 0x06, 0x07,
+		0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+		0x18, 0x03, 0x1a
+	}, {
+		0x03, 0x00, 0x17, 0x05, 0x02, 0x19, 0x06, 0x07,
+		0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+		0x18, 0x04, 0x1a
+	}
 #endif
 };
 
@@ -887,6 +908,7 @@ static bool mctl_phy_init(const struct dram_para *para,
 	struct sunxi_mctl_ctl_reg * const mctl_ctl =
 			(struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
 	u32 val, val2, *ptr, mr0, mr2;
+	const u8 *map;
 	int i;
 
 	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
@@ -942,8 +964,15 @@ static bool mctl_phy_init(const struct dram_para *para,
 	writel(val2, SUNXI_DRAM_PHY0_BASE + 0x37c);
 
 	ptr = (u32 *)(SUNXI_DRAM_PHY0_BASE + 0xc0);
-	for (i = 0; i < ARRAY_SIZE(phy_init); i++)
-		writel(phy_init[i], &ptr[i]);
+	val = readl(SUNXI_SID_BASE);
+	if (((val & 0xfbff) == 0x5000) ||
+	    ((val & 0xfeff) == 0x5c00) ||
+	    ((val & 0xf7ff) == 0x2000))
+		map = phy_addr_maps[0];
+	else
+		map = phy_addr_maps[1];
+	for (i = 0; i < ARRAY_SIZE(phy_addr_maps[0]); i++)
+		writel(map[i], &ptr[i]);
 
 	if (para->tpr10 & TPR10_CA_BIT_DELAY)
 		mctl_phy_ca_bit_delay_compensation(para, config);
Signature · 1 line
2.34.1
#4 lore raw

PATCH v2 3/9 sunxi: H616: DRAM: Adjust configuration procedure

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

When comparing configuration procedure to vendor driver, I noticed that one command was out of order and that some delays were missing.

Fix that.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +9 -1
index dfaa270d96..72194fffc2 100644
@@ -1023,12 +1023,16 @@ static bool mctl_phy_init(const struct dram_para *para,
 		clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x14c, 0xe0, 0x20);
 	}
 
+	clrbits_le32(&mctl_com->unk_0x500, 0x200);
+	udelay(1);
+
 	clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x14c, 8);
 
 	mctl_await_completion((u32 *)(SUNXI_DRAM_PHY0_BASE + 0x180), 4, 4);
 
+	udelay(1000);
+
 	writel(0x37, SUNXI_DRAM_PHY0_BASE + 0x58);
-	clrbits_le32(&mctl_com->unk_0x500, 0x200);
 
 	writel(0, &mctl_ctl->swctl);
 	setbits_le32(&mctl_ctl->dfimisc, 1);
@@ -1047,6 +1051,8 @@ static bool mctl_phy_init(const struct dram_para *para,
 	mctl_await_completion(&mctl_ctl->swstat, 1, 1);
 	mctl_await_completion(&mctl_ctl->statr, 3, 1);
 
+	udelay(200);
+
 	writel(0, &mctl_ctl->swctl);
 	clrbits_le32(&mctl_ctl->dfimisc, 1);
 
@@ -1290,8 +1296,10 @@ static bool mctl_ctrl_init(const struct dram_para *para,
 	setbits_le32(&mctl_ctl->clken, BIT(8));
 
 	clrsetbits_le32(&mctl_com->unk_0x500, BIT(24), 0x300);
+	udelay(1);
 	/* this write seems to enable PHY MMIO region */
 	setbits_le32(&mctl_com->unk_0x500, BIT(24));
+	udelay(1);
 
 	if (!mctl_phy_init(para, config))
 		return false;
Signature · 1 line
2.34.1
#5 lore raw

PATCH v2 4/9 sunxi: H616: DRAM: Adjust size scan procedure

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

It's safer to start scanning for columns first and then rows. Columns reside on LSB address pins, which means that second configuration will already have all needed row pins active.

This is also preparation for introducing DDR4 support, which need scan for banks and bank groups too.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 31 +++++++++++++++-----------
 1 file changed, 18 insertions(+), 13 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +18 -13
index 72194fffc2..2f2776ce35 100644
@@ -1371,28 +1371,33 @@ static void mctl_auto_detect_rank_width(const struct dram_para *para,
 static void mctl_auto_detect_dram_size(const struct dram_para *para,
 				       struct dram_config *config)
 {
-	/* detect row address bits */
-	config->cols = 8;
-	config->rows = 18;
+	unsigned int shift;
+
+	/* max. config for columns, but not rows */
+	config->cols = 11;
+	config->rows = 13;
 	mctl_core_init(para, config);
 
-	for (config->rows = 13; config->rows < 18; config->rows++) {
-		/* 8 banks, 8 bit per byte and 16/32 bit width */
-		if (mctl_mem_matches((1 << (config->rows + config->cols +
-					    4 + config->bus_full_width))))
+	shift = config->bus_full_width + 1;
+
+	/* detect column address bits */
+	for (config->cols = 8; config->cols < 11; config->cols++) {
+		if (mctl_mem_matches(1ULL << (config->cols + shift)))
 			break;
 	}
+	debug("detected %u columns\n", config->cols);
 
-	/* detect column address bits */
-	config->cols = 11;
+	/* reconfigure to make sure that all active rows are accessible */
+	config->rows = 18;
 	mctl_core_init(para, config);
 
-	for (config->cols = 8; config->cols < 11; config->cols++) {
-		/* 8 bits per byte and 16/32 bit width */
-		if (mctl_mem_matches(1 << (config->cols + 1 +
-					   config->bus_full_width)))
+	/* detect row address bits */
+	shift = config->bus_full_width + 4 + config->cols;
+	for (config->rows = 13; config->rows < 18; config->rows++) {
+		if (mctl_mem_matches(1ULL << (config->rows + shift)))
 			break;
 	}
+	debug("detected %u rows\n", config->rows);
 }
 
 static unsigned long mctl_calc_size(const struct dram_config *config)
Signature · 1 line
2.34.1
#6 lore raw

PATCH v2 5/9 sunxi: H616: dram: Update mbus priorities

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

CSI1 channel (22) is missing and IOMMU (25) has priority flag set in vendor bootloader. Fix that.

While at it, replace bandwidth flag with priority since original flag has always value "true".

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 41 +++++++++++++-------------
 1 file changed, 21 insertions(+), 20 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +21 -20
index 2f2776ce35..c0bcf2eec7 100644
@@ -55,8 +55,8 @@ static void mbus_configure_port(u8 port,
 	writel_relaxed(cfg1, &mctl_com->master[port].cfg1);
 }
 
-#define MBUS_CONF(port, bwlimit, qos, acs, bwl0, bwl1, bwl2)	\
-	mbus_configure_port(port, bwlimit, false, \
+#define MBUS_CONF(port, priority, qos, acs, bwl0, bwl1, bwl2)	\
+	mbus_configure_port(port, true, priority, \
 			    MBUS_QOS_ ## qos, 0, acs, bwl0, bwl1, bwl2)
 
 static void mctl_set_master_priority(void)
@@ -68,24 +68,25 @@ static void mctl_set_master_priority(void)
 	writel(399, &mctl_com->tmr);
 	writel(BIT(16), &mctl_com->bwcr);
 
-	MBUS_CONF( 0, true, HIGHEST, 0,  256,  128,  100);
-	MBUS_CONF( 1, true,    HIGH, 0, 1536, 1400,  256);
-	MBUS_CONF( 2, true, HIGHEST, 0,  512,  256,   96);
-	MBUS_CONF( 3, true,    HIGH, 0,  256,  100,   80);
-	MBUS_CONF( 4, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF( 5, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 6, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 8, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(11, true,    HIGH, 0,  256,  128,  100);
-	MBUS_CONF(14, true,    HIGH, 0, 1024,  256,   64);
-	MBUS_CONF(16, true, HIGHEST, 6, 8192, 2800, 2400);
-	MBUS_CONF(21, true, HIGHEST, 6, 2048,  768,  512);
-	MBUS_CONF(25, true, HIGHEST, 0,  100,   64,   32);
-	MBUS_CONF(26, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(37, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(38, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF(39, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(40, true,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(0, false, HIGHEST, 0,  256,  128,  100);
+	MBUS_CONF(1, false,    HIGH, 0, 1536, 1400,  256);
+	MBUS_CONF(2, false, HIGHEST, 0,  512,  256,   96);
+	MBUS_CONF(3, false,    HIGH, 0,  256,  100,   80);
+	MBUS_CONF(4, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(5, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(6, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(8, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(11, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(14, false,    HIGH, 0, 1024,  256,   64);
+	MBUS_CONF(16, false, HIGHEST, 6, 8192, 2800, 2400);
+	MBUS_CONF(21, false, HIGHEST, 6, 2048,  768,  512);
+	MBUS_CONF(22, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(25, true,  HIGHEST, 0,  100,   64,   32);
+	MBUS_CONF(26, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(37, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(38, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(39, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(40, false,    HIGH, 2,  100,   64,   32);
 
 	dmb();
 }
Signature · 1 line
2.34.1
#7 lore raw

PATCH v2 6/9 arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Add pinctrl nodes for the r_i2c node. Without the pinmux defined the r_i2c bus may fail to work, possibly if the bootloader uses rsb mode for the PMIC.

[ upstream commit: 7c9ea4ab76176f65f4f55aa144f9145a4bccaacb ]

---
 dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi | 2 ++
 1 file changed, 2 insertions(+)
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +2 -0
index 921d5f61d8..41f2c23e07 100644
@@ -836,6 +836,8 @@
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
 			dmas = <&dma 48>, <&dma 48>;
 			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c_pins>;
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;
Signature · 1 line
2.34.1
#8 lore raw

PATCH v2 7/9 sunxi: Correct TPR6 parameter for H616 DRAM driver

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Correct the default TPR6 parameter based on suggestion from Mikhail Kalashnikov. [1]

[1] https://lore.kernel.org/u-boot/[email protected]/

Fixes 4b02f0120a4b ("sunxi: H616: add LPDDR4 DRAM support")
---
 arch/arm/mach-sunxi/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-sunxi/Kconfig +1 -1
index 17666814c5..f1dcc0d105 100644
@@ -87,7 +87,7 @@ config DRAM_SUN50I_H616_TPR2
 
 config DRAM_SUN50I_H616_TPR6
 	hex "H616 DRAM TPR6 parameter"
-	default 0x3300c080
+	default 0x33c00080
 	help
 	  TPR6 value from vendor DRAM settings.
 
Signature · 1 line
2.34.1
#9 lore raw

PATCH v2 8/9 arm64: dts: allwinner: h616: Change RG35XX Series from r_rsb to r_i2c

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Change the Anbernic RG35XX series to use the r_i2c bus for the PMIC instead of the r_rsb bus. This is to keep the device tree consistent as there are at least 3 devices (the RG35XX-SP, RG28XX, and RG40XX-H) that have an external RTC on the r_i2c bus.

[ upstream commit: c712e5d0985628b1df13930489b49b740e610a2b ]

---
 .../arm64/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts    | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
dts/upstream/src/arm64/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts +3 -3
index ee30584b6a..e2bbd22bd8 100644
@@ -201,12 +201,12 @@
 	vcc-pi-supply = <&reg_cldo3>;
 };
 
-&r_rsb {
+&r_i2c {
 	status = "okay";
 
-	axp717: pmic@3a3 {
+	axp717: pmic@34 {
 		compatible = "x-powers,axp717";
-		reg = <0x3a3>;
+		reg = <0x34>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		interrupt-parent = <&nmi_intc>;
Signature · 1 line
2.34.1
#10 lore raw

PATCH v2 9/9 sunxi: Add support for Anbernic RG35XX-2024

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

The Anbernic RG35XX series of devices are based around an Allwinner H700 SoC with 1GB of RAM, 2 SD cards, and multiple input buttons.

This bootloader has been tested on the Anbernic RG35XX-2024 and RG35XX-H, but should be suitable for the entire lineup of H700 based devices.

A future series of updates will add board selection logic to identify and load the correct device tree automatically.

---
 board/sunxi/MAINTAINERS                |  5 +++
 configs/anbernic_rg35xx_h700_defconfig | 52 ++++++++++++++++++++++++++
 2 files changed, 57 insertions(+)
 create mode 100644 configs/anbernic_rg35xx_h700_defconfig
board/sunxi/MAINTAINERS +5 -0
index 4ad77c75f5..84799879e8 100644
@@ -132,6 +132,11 @@ M:	Paul Kocialkowski <[email protected]>
 S:	Maintained
 F:	configs/Ampe_A76_defconfig
 
+ANBERNIC RG35XX-2024
+M:	Chris Morgan <[email protected]>
+S:	Maintained
+F:	configs/anbernic_rg35xx_h700_defconfig
+
 BANANAPI M1 PLUS
 M:	Jagan Teki <[email protected]>
 S:	Maintained
configs/anbernic_rg35xx_h700_defconfig new file +52 -0

52 lines not on this page · raw message

Signature · 1 line
2.34.1
#11 lore raw

Re: [PATCH V2 9/9] sunxi: Add support for Anbernic RG35XX-2024

On Mon, 19 Aug 2024 09:59:38 -0500
Chris Morgan <[email protected]> wrote:

Hi Chris,

Quoted 11 lines

From: Chris Morgan <[email protected]>

The Anbernic RG35XX series of devices are based around an Allwinner H700 SoC with 1GB of RAM, 2 SD cards, and multiple input buttons.

This bootloader has been tested on the Anbernic RG35XX-2024 and RG35XX-H, but should be suitable for the entire lineup of H700 based devices.

A future series of updates will add board selection logic to identify and load the correct device tree automatically.

So diverging from the rest of sunxi, you are switching to OF_UPSTREAM and bootstd here, just for that board. Please don't do this. Both methods are board agnostic, and just depend on generic platform code to work. I have a patch to switch all H616 boards over to OF_UPSTREAM, so this wouldn't be needed to be done here. If you want to patch the DT, you could do this in arch/arm/dts as well.
For bootstd Simon had a series to enable that on sunxi, on which I commented:
https://lore.kernel.org/u-boot/[email protected]/

So please keep this board in line with the rest of the sunxi boards, and we will automatically upgrade it to both OF_UPSTREAM and bootstd as soon as that's ready.

Also the defconfig looks quite elaborate, are those options really all needed? The idea of defconfig is just to provide a, well, default. On sunxi we also try to keep that minimal.

Thanks,
Andre

Quoted 81 lines
---
 board/sunxi/MAINTAINERS                |  5 +++
 configs/anbernic_rg35xx_h700_defconfig | 52 ++++++++++++++++++++++++++
 2 files changed, 57 insertions(+)
 create mode 100644 configs/anbernic_rg35xx_h700_defconfig
board/sunxi/MAINTAINERS +5 -0
index 4ad77c75f5..84799879e8 100644
@@ -132,6 +132,11 @@ M:	Paul Kocialkowski <[email protected]>
 S:	Maintained
 F:	configs/Ampe_A76_defconfig
 
+ANBERNIC RG35XX-2024
+M:	Chris Morgan <[email protected]>
+S:	Maintained
+F:	configs/anbernic_rg35xx_h700_defconfig
+
 BANANAPI M1 PLUS
 M:	Jagan Teki <[email protected]>
 S:	Maintained
configs/anbernic_rg35xx_h700_defconfig new file +52 -0
new file mode 100644
index 0000000000..6ea2f45d2f
@@ -0,0 +1,52 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_DEFAULT_DEVICE_TREE="allwinner/sun50i-h700-anbernic-rg35xx-2024"
+CONFIG_SPL=y
+CONFIG_DRAM_SUN50I_H616_DX_ODT=0x08080808
+CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e
+CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e
+CONFIG_DRAM_SUN50I_H616_ODT_EN=0x7887bbbb
+CONFIG_DRAM_SUN50I_H616_TPR2=0x1
+CONFIG_DRAM_SUN50I_H616_TPR6=0x40808080
+CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6633
+CONFIG_DRAM_SUN50I_H616_TPR11=0x1b1f1e1c
+CONFIG_DRAM_SUN50I_H616_TPR12=0x06060606
+CONFIG_MACH_SUN50I_H616=y
+CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y
+CONFIG_SUNXI_DRAM_H616_LPDDR4=y
+CONFIG_DRAM_CLK=672
+CONFIG_R_I2C_ENABLE=y
+CONFIG_DEFAULT_FDT_FILE="sun50i-h700-anbernic-rg35xx-2024.dtb"
+CONFIG_LAST_STAGE_INIT=y
+CONFIG_SPL_I2C=y
+CONFIG_CMD_BDINFO_EXTRA=y
+CONFIG_CMD_BOOTDEV=y
+CONFIG_CMD_BOOTMETH=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_BOOTM_OPENRTOS=y
+CONFIG_BOOTM_OSE=y
+CONFIG_CMD_ADTIMG=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_BKOPS_ENABLE=y
+CONFIG_CMD_MMC_REG=y
+CONFIG_CMD_MMC_SWRITE=y
+CONFIG_CMD_SDRAM=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_UPSTREAM=y
+# CONFIG_NET is not set
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_SPL_SYS_I2C_LEGACY=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_SYS_I2C_SLAVE=0x7f
+CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP=y
+CONFIG_AXP717_POWER=y
+CONFIG_AXP_DCDC2_VOLT=940
+CONFIG_AXP_DCDC3_VOLT=1100
+CONFIG_REGEX=y
+# CONFIG_EFI_LOADER is not set
#3 lore raw

Re: [PATCH V2 2/9] sunxi: H616: DRAM: Add alternative pin mapping

In reply to Chris Morgan

On Mon, 19 Aug 2024 09:59:31 -0500
Chris Morgan <[email protected]> wrote:

Hi,

Quoted 4 lines

From: Jernej Skrabec <[email protected]>

It seems that different dies need different PHY pin mapping. Select alternatives based on "bond ID".

Do we really need this to determined at runtime? I appreciate the idea of making the code more versatile, but we have far more board specific parameters fixed at build time, so detecting a SoC type at runtime sounds a bit pointless. I am asking because this increases the SPL size by like 115 bytes.

Quoted 76 lines
---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 59 +++++++++++++++++++-------
 1 file changed, 44 insertions(+), 15 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +35 -13
index 5be2887a06..dfaa270d96 100644
@@ -225,22 +225,43 @@ static void mctl_set_addrmap(const struct dram_config *config)
 	mctl_ctl->addrmap[8] = 0x3F3F;
 }
 
-static const u8 phy_init[] = {
+static const u8 phy_addr_maps[2][27] = {
 #ifdef CONFIG_SUNXI_DRAM_H616_DDR3_1333
-	0x07, 0x0b, 0x02, 0x16, 0x0d, 0x0e, 0x14, 0x19,
-	0x0a, 0x15, 0x03, 0x13, 0x04, 0x0c, 0x10, 0x06,
-	0x0f, 0x11, 0x1a, 0x01, 0x12, 0x17, 0x00, 0x08,
-	0x09, 0x05, 0x18
+	{
+		0x07, 0x0b, 0x02, 0x16, 0x0d, 0x0e, 0x14, 0x19,
+		0x0a, 0x15, 0x03, 0x13, 0x04, 0x0c, 0x10, 0x06,
+		0x0f, 0x11, 0x1a, 0x01, 0x12, 0x17, 0x00, 0x08,
+		0x09, 0x05, 0x18
+	}, {
+		0x08, 0x02, 0x12, 0x05, 0x15, 0x17, 0x18, 0x0b,
+		0x14, 0x07, 0x04, 0x13, 0x0c, 0x00, 0x16, 0x1a,
+		0x0a, 0x11, 0x03, 0x10, 0x0e, 0x01, 0x0d, 0x19,
+		0x06, 0x09, 0x0f
+	}
 #elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR3)
-	0x18, 0x06, 0x00, 0x05, 0x04, 0x03, 0x09, 0x02,
-	0x08, 0x01, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
-	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
-	0x17, 0x19, 0x1a
+	{
+		0x18, 0x06, 0x00, 0x05, 0x04, 0x03, 0x09, 0x02,
+		0x08, 0x01, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
+		0x17, 0x19, 0x1a
+	}, {
+		0x18, 0x00, 0x04, 0x09, 0x06, 0x05, 0x02, 0x19,
+		0x17, 0x03, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
+		0x08, 0x01, 0x1a
+	}
 #elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR4)
-	0x02, 0x00, 0x17, 0x05, 0x04, 0x19, 0x06, 0x07,
-	0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
-	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
-	0x18, 0x03, 0x1a
+	{
+		0x02, 0x00, 0x17, 0x05, 0x04, 0x19, 0x06, 0x07,
+		0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+		0x18, 0x03, 0x1a
+	}, {
+		0x03, 0x00, 0x17, 0x05, 0x02, 0x19, 0x06, 0x07,
+		0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+		0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+		0x18, 0x04, 0x1a
+	}
 #endif
 };
 
@@ -887,6 +908,7 @@ static bool mctl_phy_init(const struct dram_para *para,
 	struct sunxi_mctl_ctl_reg * const mctl_ctl =
 			(struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
 	u32 val, val2, *ptr, mr0, mr2;
+	const u8 *map;
 	int i;
 
 	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_phy_init(const struct dram_para *para, · line 970

Quoted 9 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +4 -2
@@ -942,8 +964,15 @@ static bool mctl_phy_init(const struct dram_para *para,
 	writel(val2, SUNXI_DRAM_PHY0_BASE + 0x37c);
 
 	ptr = (u32 *)(SUNXI_DRAM_PHY0_BASE + 0xc0);
-	for (i = 0; i < ARRAY_SIZE(phy_init); i++)
-		writel(phy_init[i], &ptr[i]);
+	val = readl(SUNXI_SID_BASE);
+	if (((val & 0xfbff) == 0x5000) ||
+	    ((val & 0xfeff) == 0x5c00) ||
+	    ((val & 0xf7ff) == 0x2000))

so for the records, looking at
https://linux-sunxi.org/SID_Register_Guide#Currently_known_SID.27s
this means: H616, H313, H618, respectively. Which seems to be fixed for each board.

arch/arm/mach-sunxi/dram_sun50i_h616.c static bool mctl_phy_init(const struct dram_para *para, · line 975

Quoted 5 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +5 -0
+		map = phy_addr_maps[0];
+	else
+		map = phy_addr_maps[1];
+	for (i = 0; i < ARRAY_SIZE(phy_addr_maps[0]); i++)
+		writel(map[i], &ptr[i]);

If I drop the SID read above, and replace this code with something based on CONFIG_SUNXI_DRAM_H616_PHY_ADDR_MAP, it only grows by 35 bytes. If I put #if's in the array definitions above, it stays entirely at the old size, but at the cost of being hard to read - at least in the version I came up with.

What do other people say here?

Cheers,
Andre

Quoted 3 lines
arch/arm/mach-sunxi/dram_sun50i_h616.c +0 -0
 	if (para->tpr10 & TPR10_CA_BIT_DELAY)
 		mctl_phy_ca_bit_delay_compensation(para, config);