mpls01.sh: Add --allow-unsupported for modprobe
PATCH 1/1 mpls01.sh: Add --allow-unsupported for modprobe
In sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
testcases/network/mpls/mpls01.sh +3 -1
@@ -21,7 +21,9 @@ cleanup() setup() { - ROD modprobe mpls_router + if ! modprobe mpls_router > /dev/null 2>&1; then + ROD modprobe mpls_router --allow-unsupported + fi } test1()
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Hi Wei,
Quoted 17 lines
In sle-micro we encounter following error when do modprobe:
root# modprobempls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or setallow_unsupported_modules1 in
modprobe: ERROR:/etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permittedSigned-off-by Wei Gao <[email protected]>--- testcases/network/mpls/mpls01.sh | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)testcases/network/mpls/mpls01.sh +0
-0
testcases/network/mpls/mpls01.sh cleanup() · line 25
Quoted 6 lines
testcases/network/mpls/mpls01.sh +2
-1@@ -21,7 +21,9 @@ cleanup() setup() { - ROD modprobe mpls_router + if ! modprobe mpls_router > /dev/null 2>&1; then + ROD modprobe mpls_router --allow-unsupported
I'm not sure with ROD. --allow-unsupported is SUSE specific modprobe extension, which is used for SLES. It is also on Tumbleweed [1] [2] where does nothing.
If you try to run it with ROD, which quits testing on failure, all distros except SUSE products/openSUSE (e.g. Debian, Fedora, ...) which don't have mpls_router will TBROK in setup:
modprobe: unrecognised option '--allow-unsupported'.
And I'm not talking about these small distros which use busybox kmod implementation, which would also fail.
Also you remove /dev/null 2>&1 from the first command, thus other distros would not see error message about missing mpls_router module. Without looking into the source the tester will be pretty confused.
I would do:
if grep -q suse /etc/os-release; then
ROD modprobe --allow-unsupported mpls_router
else
ROD modprobe mpls_router
fi
(nit: better to put the option before the module name.)
With this, you can put in the next version:
Kind regards,
Petr
testcases/network/mpls/mpls01.sh cleanup() · line 29
Quoted 4 lines
testcases/network/mpls/mpls01.sh +1
-0+ fi } test1()
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
Hi!
Quoted 12 lines
I'm not sure with ROD. --allow-unsupported is SUSE specific modprobe extension, which is used for SLES. It is also on Tumbleweed [1] [2] where does nothing.
If you try to run it with ROD, which quits testing on failure, all distros except SUSE products/openSUSE (e.g. Debian, Fedora, ...) which don't have
mpls_routerwill TBROK in setup:modprobe: unrecognised option '--allow-unsupported'.
And I'm not talking about these small distros which use busybox kmod implementation, which would also fail.
Quoted 7 lines
Also you remove
/dev/null2>&1 from the first command, thus other distros would not see error message about missingmpls_routermodule. Without looking into the source the tester will be pretty confused.I would do:
if grep -q suse
/etc/os-release; then
There are a couple of english words that contain "suse" as a substring if one of these ends up in the os-release it would match, e.g. the os-release may contain VERSION="24 (Disused Miracle)". And yes both Fedora and Ubuntu seems to include the the code names in the file.
So I would be stricter here and checked for ID=suse.
Signature · 5 lines
Cyril Hrubis [email protected] -- Mailing list info: https://lists.linux.it/listinfo/ltp
Hi Cyril, Wei,
Quoted 10 lines
Hi!
Quoted 1 line
if grep -q suse
/etc/os-release; thenThere are a couple of english words that contain "suse" as a substring if one of these ends up in the os-release it would match, e.g. the os-release may contain VERSION="24 (Disused Miracle)". And yes both Fedora and Ubuntu seems to include the the code names in the file.
So I would be stricter here and checked for ID=suse.
Very good point.
FYI SLES (removed non-related lines)
NAME="SLES"
VERSION="15-SP6"
PRETTY_NAME="SUSE Linux Enterprise Server 15 SP6"
ID="sles"
ID_LIKE="suse"
SLE Micro (removed non-related lines):
NAME="SL-Micro"
PRETTY_NAME="SUSE Linux Micro 6.0"
ID="sl-micro"
ID_LIKE="suse"
Debian:
NAME="Debian GNU/Linux"
ID=debian
=> SUSE quite all variables, but at least Debian not (ID=debian). Therefore for more complex scenarios I would source the file (. /etc/os-release). But in this case grep sl-micro could be enough (unique enough).
Will you ack this change (RBT/ABT) in v2 [1] (newer version than this, I would change before merge)?
- if grep -q suse /etc/os-release; then
+ if grep -q 'sl-micro' /etc/os-release; then
Kind regards,
Petr
[1] https://patchwork.ozlabs.org/project/ltp/patch/[email protected]/
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
PATCH v2 1/1 mpls01.sh: Add --allow-unsupported for modprobe
In reply to Wei Gao via ltpIn sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
testcases/network/mpls/mpls01.sh +5 -1
@@ -21,7 +21,11 @@ cleanup() setup() { - ROD modprobe mpls_router + if grep -q suse /etc/os-release; then + ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Quoted 19 lines
In sle-micro we encounter following error when do modprobe:
root# modprobempls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or setallow_unsupported_modules1 in
modprobe: ERROR:/etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permittedSigned-off-by Wei Gao <[email protected]>Reviewed-by Petr Vorel <[email protected]>--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)testcases/network/mpls/mpls01.sh +0
-0
testcases/network/mpls/mpls01.sh cleanup() · line 24
Quoted 5 lines
testcases/network/mpls/mpls01.sh +1
-1@@ -21,7 +21,11 @@ cleanup() setup() { - ROD modprobe mpls_router + if grep -q suse /etc/os-release; then
Cyril asked for more specific grep in v1
https://lore.kernel.org/ltp/[email protected]/
My suggestion to change before merge:
https://lore.kernel.org/ltp/20240902110037.GD279460@pevik/
- if grep -q suse /etc/os-release; then
+ if grep -q 'sl-micro' /etc/os-release; then
Kind regards,
Petr
Quoted 7 lines
testcases/network/mpls/mpls01.sh +4
-0+ ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
PATCH v3 1/1 mpls01.sh: Add --allow-unsupported for modprobe
In reply to Wei Gao via ltpIn sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
testcases/network/mpls/mpls01.sh +5 -1
@@ -21,7 +21,11 @@ cleanup() setup() { - ROD modprobe mpls_router + if grep -q 'sl-micro' /etc/os-release; then + ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Hi Wei,
Quoted 6 lines
In sle-micro we encounter following error when do modprobe:
root# modprobempls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or setallow_unsupported_modules1 in
modprobe: ERROR:/etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
This is needed in other mpls tests (mpls0[2-4].sh, it needs to be in mpls_lib.sh to be reused.
Kind regards,
Petr
Quoted 23 lines
Signed-off-by Wei Gao <[email protected]>Reviewed-by Petr Vorel <[email protected]>--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)testcases/network/mpls/mpls01.sh +5
-1@@ -21,7 +21,11 @@ cleanup() setup() { - ROD modprobe mpls_router + if grep -q 'sl-micro' /etc/os-release; then + ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
Hi!
Quoted 11 lines
Signed-off-by Wei Gao <[email protected]>Reviewed-by Petr Vorel <[email protected]>--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)testcases/network/mpls/mpls01.sh +0
-0
testcases/network/mpls/mpls01.sh cleanup() · line 24
Quoted 5 lines
testcases/network/mpls/mpls01.sh +1
-1@@ -21,7 +21,11 @@ cleanup() setup() { - ROD modprobe mpls_router + if grep -q 'sl-micro' /etc/os-release; then
I do not like how specific is this check. The --allow-unsupported should be at best no-op for SLE and openSUSE, right? So I would go for the check of ID=suse rather than specifying just single variant.
Quoted 13 lines
testcases/network/mpls/mpls01.sh +4
-0+ ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Signature · 5 lines
Cyril Hrubis [email protected] -- Mailing list info: https://lists.linux.it/listinfo/ltp
Hi Cyril,
Quoted 13 lines
Hi!
Quoted 11 lines
Signed-off-by Wei Gao <[email protected]>Reviewed-by Petr Vorel <[email protected]>--- testcases/network/mpls/mpls01.sh | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)testcases/network/mpls/mpls01.sh +0
-0@@ -21,7 +21,11 @@ cleanup()
Quoted 7 lines
testcases/network/mpls/mpls01.sh cleanup() · line 24
Quoted 4 lines
testcases/network/mpls/mpls01.sh +1
-1setup() { - ROD modprobe mpls_router + if grep -q 'sl-micro' /etc/os-release; thenI do not like how specific is this check. The --allow-unsupported should be at best no-op for SLE and openSUSE, right?
Yes. I would personally avoid it (not needed so far), but sure it can work.
Quoted 2 lines
So I would go for the
check of ID=suse rather than specifying just single variant.
$ grep ^ID /etc/os-release # SLE Micro ID="sl-micro" ID_LIKE="suse"
$ grep ID_ /etc/os-release # Tumbleweed ID="opensuse-tumbleweed" ID_LIKE="opensuse suse"
$ grep ^ID /etc/os-release # SLES 15-SP6 ID="sles" ID_LIKE="suse"
$ grep ^ID /etc/os-release # SLES 12-SP5 (still supported) ID="sles"
If we dare to ignore SLE12-SP5 (and older), we could use:
=> grep -q -w ID_LIKE.*suse /etc/os-release (Using -w to mitigate "suse" as part of longer word.)
There is another problem: mpls_setup() also tries to load modules
modprobe -a mpls_router mpls_iptunnel mpls_gso failed on both lhost and rhost via:
tst_net_run -s "modprobe -a $TST_NEEDS_DRIVERS"
which is run on all mpls tests. And even mpls01.sh gets fixed,
the other 3 remaining tests fails due missing --allow-unsupported for other mpls modules.
I guess we can expect both sides are the same distros, thus we could do evaluation only on lhost. And, we could for simplicity run modprobe also on both sides in mpls01.sh, thus putting it into function. This code could be in new function and called in mpls_setup + in mpls01.sh:
local module
local args
grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported'
if [ "$TST_NEEDS_DRIVERS" ]; then
tst_net_run -s "modprobe $args -a $TST_NEEDS_DRIVERS"
fi
Wei, feel free to add it into new version. I can fix your grep in your version and send a follow up patch. Whatever you prefer.
Kind regards,
Petr
Quoted 13 lines
Quoted 13 lines
testcases/network/mpls/mpls01.sh +4
-0+ ROD modprobe --allow-unsupported mpls_router + else + ROD modprobe mpls_router + fi } test1()Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
PATCH v4 1/1 mpls01.sh: Add --allow-unsupported for modprobe
In reply to Wei Gao via ltpIn sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 4 ++-- testcases/network/mpls/mpls_lib.sh | 10 ++++++++++ 2 files changed, 12 insertions(+), 2 deletions(-)
testcases/network/mpls/mpls01.sh +2 -2
@@ -21,7 +21,7 @@ cleanup() setup() { - ROD modprobe mpls_router + mpls_setup_driver } test1()
@@ -66,5 +66,5 @@ test3() tst_res TPASS "created and removed mpls routes" } -. tst_net.sh +. mpls_lib.sh tst_run
testcases/network/mpls/mpls_lib.sh +10 -0
@@ -33,6 +33,16 @@ mpls_virt_cleanup() mpls_cleanup } +mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported' + if [ "$TST_NEEDS_DRIVERS" ]; then + tst_net_run -s "modprobe $args -a $TST_NEEDS_DRIVERS" + fi +} + mpls_setup() { local label="$1"
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Hi Wei,
I suggest these changes:
1) use mpls_setup_driver also in mpls_setup()
- replace tst_net_run(). I don't understand why you did not do it in the patchset (I suggested that), but I can replace it during merge.
2) update the commit message: s/mpls01.sh/mpls01/
(fixing all mpls tests)
With that:
Kind regards,
Petr
+++ testcases/network/mpls/mpls_lib.sh
@@ -47,7 +47,7 @@ mpls_setup()
{
local label="$1"
- tst_net_run -s "modprobe -a $TST_NEEDS_DRIVERS"
+ mpls_setup_driver
ROD sysctl -q net.mpls.conf.$(tst_iface).input=1 tst_set_sysctl net.mpls.conf.lo.input 1 safe
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
Quoted 7 lines · Petr Vorel
Hi Wei,
I suggest these changes:
1) use
mpls_setup_driveralso inmpls_setup()
- replacetst_net_run(). I don't understand why you did not do it in the patchset (I suggested that), but I can replace it during merge.
Sorry i forget that, will sent another patch. Thanks for point that.
Quoted 19 lines
2) update the commit message: s/mpls01.sh/mpls01/
(fixing all mpls tests)With that:
Reviewed-by Petr Vorel <[email protected]>Kind regards,
Petr+++
testcases/network/mpls/mpls_lib.sh(quoted diff) +1
-1@@ -47,7 +47,7 @@ mpls_setup() { local label="$1" - tst_net_run -s "modprobe -a $TST_NEEDS_DRIVERS" + mpls_setup_driver ROD sysctl -q net.mpls.conf.$(tst_iface).input=1 tst_set_sysctl net.mpls.conf.lo.input 1 safe
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
PATCH v5 1/1 mpls01.sh: Add --allow-unsupported for modprobe
In reply to Wei Gao via ltpIn sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 4 ++-- testcases/network/mpls/mpls_lib.sh | 12 +++++++++++- 2 files changed, 13 insertions(+), 3 deletions(-)
testcases/network/mpls/mpls01.sh +2 -2
@@ -21,7 +21,7 @@ cleanup() setup() { - ROD modprobe mpls_router + mpls_setup_driver } test1()
@@ -66,5 +66,5 @@ test3() tst_res TPASS "created and removed mpls routes" } -. tst_net.sh +. mpls_lib.sh tst_run
testcases/network/mpls/mpls_lib.sh +11 -1
@@ -33,11 +33,21 @@ mpls_virt_cleanup() mpls_cleanup } +mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported' + if [ "$TST_NEEDS_DRIVERS" ]; then + tst_net_run -s "modprobe $args -a $TST_NEEDS_DRIVERS" + fi +} + mpls_setup() { local label="$1" - tst_net_run -s "modprobe -a $TST_NEEDS_DRIVERS" + mpls_setup_driver ROD sysctl -q net.mpls.conf.$(tst_iface).input=1 tst_set_sysctl net.mpls.conf.lo.input 1 safe
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
PATCH v6 1/1 mpls01: Add --allow-unsupported for modprobe(fixing all mpls cases)
In sle-micro we encounter following error when do modprobe:
root# modprobe mpls_router
modprobe: ERROR: module 'mpls_router' is unsupported
modprobe: ERROR: Use --allow-unsupported or set allow_unsupported_modules 1 in
modprobe: ERROR: /etc/modprobe.d/10-unsupported-modules.conf
modprobe: ERROR: could not insert 'mpls_router': Operation not permitted
--- testcases/network/mpls/mpls01.sh | 4 ++-- testcases/network/mpls/mpls_lib.sh | 12 +++++++++++- 2 files changed, 13 insertions(+), 3 deletions(-)
testcases/network/mpls/mpls01.sh +2 -2
@@ -21,7 +21,7 @@ cleanup() setup() { - ROD modprobe mpls_router + mpls_setup_driver } test1()
@@ -66,5 +66,5 @@ test3() tst_res TPASS "created and removed mpls routes" } -. tst_net.sh +. mpls_lib.sh tst_run
testcases/network/mpls/mpls_lib.sh +11 -1
@@ -33,11 +33,21 @@ mpls_virt_cleanup() mpls_cleanup } +mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported' + if [ "$TST_NEEDS_DRIVERS" ]; then + tst_net_run -s "modprobe $args -a $TST_NEEDS_DRIVERS" + fi +} + mpls_setup() { local label="$1" - tst_net_run -s "modprobe -a $TST_NEEDS_DRIVERS" + mpls_setup_driver ROD sysctl -q net.mpls.conf.$(tst_iface).input=1 tst_set_sysctl net.mpls.conf.lo.input 1 safe
Signature · 5 lines
2.35.3 -- Mailing list info: https://lists.linux.it/listinfo/ltp
Re: [LTP] [PATCH v6] mpls01: Add --allow-unsupported for modprobe(fixing all mpls cases)
Hi Wei,
...
testcases/network/mpls/mpls_lib.sh mpls_virt_cleanup() · line 40
Quoted 5 lines
testcases/network/mpls/mpls_lib.sh +5
-0+mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported'
I'm going to merge in few hours with following change
- grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported'
+ grep -q -w ID_LIKE.*suse /etc/os-release && args='--allow-unsupported'
(to implement Cyril's wish to apply the change also for SLES and openSUSE. I'm sorry although I suggested that in v4, then in the full example I in the end used 'sl-micro'.
Kind regards,
Petr
Quoted 8 lines
testcases/network/mpls/mpls_lib.sh +5
-0+ if [ "$TST_NEEDS_DRIVERS" ]; then + tst_net_run -s "modprobe $args -a $TST_NEEDS_DRIVERS" + fi +} + mpls_setup() { local label="$1"
...
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp
Re: [LTP] [PATCH v6] mpls01: Add --allow-unsupported for modprobe(fixing all mpls cases)
Hi!
Quoted 11 lines
testcases/network/mpls/mpls_lib.sh mpls_virt_cleanup() · line 40
Quoted 5 lines
testcases/network/mpls/mpls_lib.sh +5
-0+mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported'I'm going to merge in few hours with following change
(quoted diff) +1
-1- grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported' + grep -q -w ID_LIKE.*suse /etc/os-release && args='--allow-unsupported'
Quoted 3 lines
(to implement Cyril's wish to apply the change also for SLES and openSUSE. I'm sorry although I suggested that in v4, then in the full example I in the end used 'sl-micro'.
Works for me. Acked-by: Cyril Hrubis <[email protected]>
Signature · 5 lines
Cyril Hrubis [email protected] -- Mailing list info: https://lists.linux.it/listinfo/ltp
Re: [LTP] [PATCH v6] mpls01: Add --allow-unsupported for modprobe(fixing all mpls cases)
Hi Cyril,
Quoted 9 lines
Hi!
Quoted 7 lines
testcases/network/mpls/mpls_lib.sh mpls_virt_cleanup() · line 40
Quoted 5 lines
testcases/network/mpls/mpls_lib.sh +5
-0+mpls_setup_driver() +{ + local args + + grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported'I'm going to merge in few hours with following change
Quoted 8 lines
Quoted 6 lines
(quoted diff) +1
-1- grep -q 'sl-micro' /etc/os-release && args='--allow-unsupported' + grep -q -w ID_LIKE.*suse /etc/os-release && args='--allow-unsupported'(to implement Cyril's wish to apply the change also for SLES and openSUSE. I'm sorry although I suggested that in v4, then in the full example I in the end used 'sl-micro'.
Works for me. Acked-by: Cyril Hrubis <[email protected]>
Thanks for your ack, merged.
Kind regards,
Petr
Signature · 1 line
Mailing list info: https://lists.linux.it/listinfo/ltp