Skip to contentSkip to conversation

Add Anbernic RG35XX-2024

PATCH In review Chris Morgan 3 participants 14 messages Aug 30, 2024 – Sep 4, 2024

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v3 cover Add Anbernic RG35XX-2024

From: Chris Morgan <[email protected]>

Add support for the Anbernic RG35XX-2024.

This device is a handheld gaming console (series) based around the Anbernic H700 SoC. It comes with 1GB of RAM and multiple face buttons for input.

Add support for the simplest model for now, and then iterate later to add board detection logic, support the entire device lineup, and move to using the mainline device tree.

Changes since V2:
- Moved back to using the U-Boot specific device tree, for now.
- Changed the cherry picked device tree commits to update both the U-Boot device tree and the mainline device tree, so either could be used.
- Made the DRAM PHY pinconf compile time selectable instead of runtime selectable to decrease SPL memory usage.

Changes since V1:
- Removed DDR3 and LPDDR3 patches from Jernej Skrabec, as they could not be tested by me and were not required to bring up this device.
- Changed the default TPR6 parameter based on a suggestion from Mikhail Kalashnikov.
- Cherry picked 2 commits from linux-next and converted devicetree to upstream.

Chris Morgan (5):
sunxi: H616: DRAM: Add alternative pin mapping
sunxi: Correct TPR6 parameter for H616 DRAM driver
arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes
arm64: dts: allwinner: h616: Change RG35XX PMIC to r_i2c
sunxi: Add support for Anbernic RG35XX-2024

Jernej Skrabec (4):
sunxi: H616: dram: LPDDR4: adjust settings
sunxi: H616: DRAM: Adjust configuration procedure
sunxi: H616: DRAM: Adjust size scan procedure
sunxi: H616: dram: Update mbus priorities

 arch/arm/dts/sun50i-h616.dtsi                 |   2 +
 .../dts/sun50i-h700-anbernic-rg35xx-2024.dts  |   6 +-
 arch/arm/mach-sunxi/Kconfig                   |  19 ++-
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 137 ++++++++++++------
 .../dram_timings/h616_lpddr4_2133.c           |   2 +-
 board/sunxi/MAINTAINERS                       |   5 +
 configs/anbernic_rg35xx_h700_defconfig        |  28 ++++
 .../src/arm64/allwinner/sun50i-h616.dtsi      |   2 +
 .../sun50i-h700-anbernic-rg35xx-2024.dts      |   6 +-
 9 files changed, 154 insertions(+), 53 deletions(-)
 create mode 100644 configs/anbernic_rg35xx_h700_defconfig
Signature · 1 line
2.34.1
#1 lore raw

PATCH v3 1/9 sunxi: H616: dram: LPDDR4: adjust settings

From: Jernej Skrabec <[email protected]>

Adjust H616 LPDDR4 DRAM settings to be in line with vendor driver.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c        | 33 +++++++++++++------
 .../dram_timings/h616_lpddr4_2133.c           |  2 +-
 2 files changed, 24 insertions(+), 11 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +23 -10
index 37c139e0ee..5be2887a06 100644
@@ -293,14 +293,22 @@ static void mctl_phy_configure_odt(const struct dram_para *para)
 	dmb();
 }
 
-static bool mctl_phy_write_leveling(const struct dram_config *config)
+static bool mctl_phy_write_leveling(const struct dram_para *para,
+				    const struct dram_config *config)
 {
 	bool result = true;
 	u32 val;
 
 	clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 8, 0xc0, 0x80);
-	writel(4, SUNXI_DRAM_PHY0_BASE + 0xc);
-	writel(0x40, SUNXI_DRAM_PHY0_BASE + 0x10);
+
+	if (para->type == SUNXI_DRAM_TYPE_LPDDR4) {
+		/* MR2 value */
+		writel(0x1b, SUNXI_DRAM_PHY0_BASE + 0xc);
+		writel(0, SUNXI_DRAM_PHY0_BASE + 0x10);
+	} else {
+		writel(4, SUNXI_DRAM_PHY0_BASE + 0xc);
+		writel(0x40, SUNXI_DRAM_PHY0_BASE + 0x10);
+	}
 
 	setbits_le32(SUNXI_DRAM_PHY0_BASE + 8, 4);
 
@@ -859,9 +867,9 @@ static void mctl_phy_ca_bit_delay_compensation(const struct dram_para *para,
 		}
 		break;
 	case SUNXI_DRAM_TYPE_LPDDR4:
-		if (para->tpr2 & 1) {
-			writel(val, SUNXI_DRAM_PHY0_BASE + 0x788);
-		} else {
+		writel(val, SUNXI_DRAM_PHY0_BASE + 0x788);
+		if (config->ranks == 2) {
+			val = (para->tpr10 >> 11) & 0x1e;
 			writel(val, SUNXI_DRAM_PHY0_BASE + 0x794);
 		};
 		break;
@@ -1080,19 +1088,27 @@ static bool mctl_phy_init(const struct dram_para *para,
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xb04, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xc72, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0xe09, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 
 		writel(0x1624, &mctl_ctl->mrctrl1);
+		udelay(10);
 		writel(0x80000030, &mctl_ctl->mrctrl0);
+		udelay(10);
 		mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
 		break;
 	case SUNXI_DRAM_TYPE_DDR4:
@@ -1108,7 +1124,7 @@ static bool mctl_phy_init(const struct dram_para *para,
 
 	if (para->tpr10 & TPR10_WRITE_LEVELING) {
 		for (i = 0; i < 5; i++)
-			if (mctl_phy_write_leveling(config))
+			if (mctl_phy_write_leveling(para, config))
 				break;
 		if (i == 5) {
 			debug("write leveling failed!\n");
@@ -1234,9 +1250,6 @@ static bool mctl_ctrl_init(const struct dram_para *para,
 	setbits_le32(&mctl_ctl->unk_0x3180, BIT(31) | BIT(30));
 	setbits_le32(&mctl_ctl->unk_0x4180, BIT(31) | BIT(30));
 
-	if (para->type == SUNXI_DRAM_TYPE_LPDDR4)
-		setbits_le32(&mctl_ctl->dbictl, 0x1);
-
 	setbits_le32(&mctl_ctl->rfshctl3, BIT(0));
 	clrbits_le32(&mctl_ctl->dfimisc, BIT(0));
 
arch/arm/mach-sunxi/dram_timings/h616_lpddr4_2133.c +1 -1
index e6446b9180..6f5c4acbd6 100644
@@ -23,7 +23,7 @@ void mctl_set_timing_params(const struct dram_para *para)
 	u8 trcd		= max(ns_to_t(18), 2);
 	u8 trc		= ns_to_t(65);
 	u8 txp		= max(ns_to_t(8), 2);
-	u8 trtp		= max(ns_to_t(8), 4);
+	u8 trtp		= 4;
 	u8 trp		= ns_to_t(21);
 	u8 tras		= ns_to_t(42);
 	u16 trefi	= ns_to_t(3904) / 32;
Signature · 1 line
2.34.1
#2 lore raw

PATCH v3 2/9 sunxi: H616: DRAM: Add alternative pin mapping

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

It seems that different dies need different PHY pin mapping. Select alternatives at compile time.

[adapted to switch from runtime to compile time config]
---
 arch/arm/mach-sunxi/Kconfig            | 17 +++++++++++++++++
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 22 +++++++++++++++++++++-
 2 files changed, 38 insertions(+), 1 deletion(-)
arch/arm/mach-sunxi/Kconfig +17 -0
index 17666814c5..078f8c19fa 100644
@@ -108,6 +108,23 @@ config DRAM_SUN50I_H616_TPR12
 	default 0x0
 	help
 	  TPR12 value from vendor DRAM settings.
+
+choice
+	prompt "H616 PHY pin mapping selection"
+	default DRAM_SUN50I_H616_PHY_ADDR_MAP_0
+
+config DRAM_SUN50I_H616_PHY_ADDR_MAP_0
+	bool "H313/H616/H618"
+	help
+	  The pin mapping selection used by the H313, H616, H618, and
+	  possibly other dies which use the H616 DRAM controller.
+
+config DRAM_SUN50I_H616_PHY_ADDR_MAP_1
+	bool "H700"
+	help
+	  The pin mapping selection used by the H700 and possibly other
+	  dies which use the H616 DRAM controller.
+endchoice
 endif
 
 config SUN6I_PRCM
arch/arm/mach-sunxi/dram_sun50i_h616.c +21 -1
index 5be2887a06..52f7799173 100644
@@ -225,6 +225,26 @@ static void mctl_set_addrmap(const struct dram_config *config)
 	mctl_ctl->addrmap[8] = 0x3F3F;
 }
 
+#ifdef CONFIG_DRAM_SUN50I_H616_PHY_ADDR_MAP_1
+static const u8 phy_init[] = {
+#ifdef CONFIG_SUNXI_DRAM_H616_DDR3_1333
+	0x08, 0x02, 0x12, 0x05, 0x15, 0x17, 0x18, 0x0b,
+	0x14, 0x07, 0x04, 0x13, 0x0c, 0x00, 0x16, 0x1a,
+	0x0a, 0x11, 0x03, 0x10, 0x0e, 0x01, 0x0d, 0x19,
+	0x06, 0x09, 0x0f
+#elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR3)
+	0x18, 0x00, 0x04, 0x09, 0x06, 0x05, 0x02, 0x19,
+	0x17, 0x03, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x07,
+	0x08, 0x01, 0x1a
+#elif defined(CONFIG_SUNXI_DRAM_H616_LPDDR4)
+	0x03, 0x00, 0x17, 0x05, 0x02, 0x19, 0x06, 0x07,
+	0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+	0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x01,
+	0x18, 0x04, 0x1a
+#endif
+};
+#else /* CONFIG_DRAM_SUN50I_H616_PHY_ADDR_MAP_0 */
 static const u8 phy_init[] = {
 #ifdef CONFIG_SUNXI_DRAM_H616_DDR3_1333
 	0x07, 0x0b, 0x02, 0x16, 0x0d, 0x0e, 0x14, 0x19,
@@ -243,7 +263,7 @@ static const u8 phy_init[] = {
 	0x18, 0x03, 0x1a
 #endif
 };
-
+#endif /* CONFIG_DRAM_SUN50I_H616_PHY_ADDR_MAP_0 */
 #define MASK_BYTE(reg, nr) (((reg) >> ((nr) * 8)) & 0x1f)
 static void mctl_phy_configure_odt(const struct dram_para *para)
 {
Signature · 1 line
2.34.1
#3 lore raw

PATCH v3 3/9 sunxi: H616: DRAM: Adjust configuration procedure

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

When comparing configuration procedure to vendor driver, I noticed that one command was out of order and that some delays were missing.

Fix that.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +9 -1
index 52f7799173..35405915e9 100644
@@ -1014,12 +1014,16 @@ static bool mctl_phy_init(const struct dram_para *para,
 		clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x14c, 0xe0, 0x20);
 	}
 
+	clrbits_le32(&mctl_com->unk_0x500, 0x200);
+	udelay(1);
+
 	clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x14c, 8);
 
 	mctl_await_completion((u32 *)(SUNXI_DRAM_PHY0_BASE + 0x180), 4, 4);
 
+	udelay(1000);
+
 	writel(0x37, SUNXI_DRAM_PHY0_BASE + 0x58);
-	clrbits_le32(&mctl_com->unk_0x500, 0x200);
 
 	writel(0, &mctl_ctl->swctl);
 	setbits_le32(&mctl_ctl->dfimisc, 1);
@@ -1038,6 +1042,8 @@ static bool mctl_phy_init(const struct dram_para *para,
 	mctl_await_completion(&mctl_ctl->swstat, 1, 1);
 	mctl_await_completion(&mctl_ctl->statr, 3, 1);
 
+	udelay(200);
+
 	writel(0, &mctl_ctl->swctl);
 	clrbits_le32(&mctl_ctl->dfimisc, 1);
 
@@ -1281,8 +1287,10 @@ static bool mctl_ctrl_init(const struct dram_para *para,
 	setbits_le32(&mctl_ctl->clken, BIT(8));
 
 	clrsetbits_le32(&mctl_com->unk_0x500, BIT(24), 0x300);
+	udelay(1);
 	/* this write seems to enable PHY MMIO region */
 	setbits_le32(&mctl_com->unk_0x500, BIT(24));
+	udelay(1);
 
 	if (!mctl_phy_init(para, config))
 		return false;
Signature · 1 line
2.34.1
#4 lore raw

PATCH v3 4/9 sunxi: H616: DRAM: Adjust size scan procedure

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

It's safer to start scanning for columns first and then rows. Columns reside on LSB address pins, which means that second configuration will already have all needed row pins active.

This is also preparation for introducing DDR4 support, which need scan for banks and bank groups too.

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 31 +++++++++++++++-----------
 1 file changed, 18 insertions(+), 13 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +18 -13
index 35405915e9..4782e6fe38 100644
@@ -1362,28 +1362,33 @@ static void mctl_auto_detect_rank_width(const struct dram_para *para,
 static void mctl_auto_detect_dram_size(const struct dram_para *para,
 				       struct dram_config *config)
 {
-	/* detect row address bits */
-	config->cols = 8;
-	config->rows = 18;
+	unsigned int shift;
+
+	/* max. config for columns, but not rows */
+	config->cols = 11;
+	config->rows = 13;
 	mctl_core_init(para, config);
 
-	for (config->rows = 13; config->rows < 18; config->rows++) {
-		/* 8 banks, 8 bit per byte and 16/32 bit width */
-		if (mctl_mem_matches((1 << (config->rows + config->cols +
-					    4 + config->bus_full_width))))
+	shift = config->bus_full_width + 1;
+
+	/* detect column address bits */
+	for (config->cols = 8; config->cols < 11; config->cols++) {
+		if (mctl_mem_matches(1ULL << (config->cols + shift)))
 			break;
 	}
+	debug("detected %u columns\n", config->cols);
 
-	/* detect column address bits */
-	config->cols = 11;
+	/* reconfigure to make sure that all active rows are accessible */
+	config->rows = 18;
 	mctl_core_init(para, config);
 
-	for (config->cols = 8; config->cols < 11; config->cols++) {
-		/* 8 bits per byte and 16/32 bit width */
-		if (mctl_mem_matches(1 << (config->cols + 1 +
-					   config->bus_full_width)))
+	/* detect row address bits */
+	shift = config->bus_full_width + 4 + config->cols;
+	for (config->rows = 13; config->rows < 18; config->rows++) {
+		if (mctl_mem_matches(1ULL << (config->rows + shift)))
 			break;
 	}
+	debug("detected %u rows\n", config->rows);
 }
 
 static unsigned long mctl_calc_size(const struct dram_config *config)
Signature · 1 line
2.34.1
#5 lore raw

PATCH v3 5/9 sunxi: H616: dram: Update mbus priorities

In reply to Chris Morgan

From: Jernej Skrabec <[email protected]>

CSI1 channel (22) is missing and IOMMU (25) has priority flag set in vendor bootloader. Fix that.

While at it, replace bandwidth flag with priority since original flag has always value "true".

---
 arch/arm/mach-sunxi/dram_sun50i_h616.c | 41 +++++++++++++-------------
 1 file changed, 21 insertions(+), 20 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +21 -20
index 4782e6fe38..863c4f1d7a 100644
@@ -55,8 +55,8 @@ static void mbus_configure_port(u8 port,
 	writel_relaxed(cfg1, &mctl_com->master[port].cfg1);
 }
 
-#define MBUS_CONF(port, bwlimit, qos, acs, bwl0, bwl1, bwl2)	\
-	mbus_configure_port(port, bwlimit, false, \
+#define MBUS_CONF(port, priority, qos, acs, bwl0, bwl1, bwl2)	\
+	mbus_configure_port(port, true, priority, \
 			    MBUS_QOS_ ## qos, 0, acs, bwl0, bwl1, bwl2)
 
 static void mctl_set_master_priority(void)
@@ -68,24 +68,25 @@ static void mctl_set_master_priority(void)
 	writel(399, &mctl_com->tmr);
 	writel(BIT(16), &mctl_com->bwcr);
 
-	MBUS_CONF( 0, true, HIGHEST, 0,  256,  128,  100);
-	MBUS_CONF( 1, true,    HIGH, 0, 1536, 1400,  256);
-	MBUS_CONF( 2, true, HIGHEST, 0,  512,  256,   96);
-	MBUS_CONF( 3, true,    HIGH, 0,  256,  100,   80);
-	MBUS_CONF( 4, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF( 5, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 6, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 8, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(11, true,    HIGH, 0,  256,  128,  100);
-	MBUS_CONF(14, true,    HIGH, 0, 1024,  256,   64);
-	MBUS_CONF(16, true, HIGHEST, 6, 8192, 2800, 2400);
-	MBUS_CONF(21, true, HIGHEST, 6, 2048,  768,  512);
-	MBUS_CONF(25, true, HIGHEST, 0,  100,   64,   32);
-	MBUS_CONF(26, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(37, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(38, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF(39, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(40, true,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(0, false, HIGHEST, 0,  256,  128,  100);
+	MBUS_CONF(1, false,    HIGH, 0, 1536, 1400,  256);
+	MBUS_CONF(2, false, HIGHEST, 0,  512,  256,   96);
+	MBUS_CONF(3, false,    HIGH, 0,  256,  100,   80);
+	MBUS_CONF(4, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(5, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(6, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(8, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(11, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(14, false,    HIGH, 0, 1024,  256,   64);
+	MBUS_CONF(16, false, HIGHEST, 6, 8192, 2800, 2400);
+	MBUS_CONF(21, false, HIGHEST, 6, 2048,  768,  512);
+	MBUS_CONF(22, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(25, true,  HIGHEST, 0,  100,   64,   32);
+	MBUS_CONF(26, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(37, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(38, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(39, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(40, false,    HIGH, 2,  100,   64,   32);
 
 	dmb();
 }
Signature · 1 line
2.34.1
#7 lore raw

PATCH v3 6/9 sunxi: Correct TPR6 parameter for H616 DRAM driver

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Correct the default TPR6 parameter based on suggestion from Mikhail Kalashnikov. [1]

[1] https://lore.kernel.org/u-boot/[email protected]/

Fixes 4b02f0120a4b ("sunxi: H616: add LPDDR4 DRAM support")
---
 arch/arm/mach-sunxi/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-sunxi/Kconfig +1 -1
index 078f8c19fa..5b3571025f 100644
@@ -87,7 +87,7 @@ config DRAM_SUN50I_H616_TPR2
 
 config DRAM_SUN50I_H616_TPR6
 	hex "H616 DRAM TPR6 parameter"
-	default 0x3300c080
+	default 0x33c00080
 	help
 	  TPR6 value from vendor DRAM settings.
 
Signature · 1 line
2.34.1
#9 lore raw

PATCH v3 7/9 arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Add pinctrl nodes for the r_i2c node. Without the pinmux defined the r_i2c bus may fail to work, possibly if the bootloader uses rsb mode for the PMIC.

[ upstream commit: 7c9ea4ab76176f65f4f55aa144f9145a4bccaacb ]

---
 arch/arm/dts/sun50i-h616.dtsi                     | 2 ++
 dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi | 2 ++
 2 files changed, 4 insertions(+)
arch/arm/dts/sun50i-h616.dtsi +2 -0
index 921d5f61d8..41f2c23e07 100644
@@ -836,6 +836,8 @@
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
 			dmas = <&dma 48>, <&dma 48>;
 			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c_pins>;
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +2 -0
index 921d5f61d8..41f2c23e07 100644
@@ -836,6 +836,8 @@
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
 			dmas = <&dma 48>, <&dma 48>;
 			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c_pins>;
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;
Signature · 1 line
2.34.1
#12 lore raw

PATCH v3 8/9 arm64: dts: allwinner: h616: Change RG35XX PMIC to r_i2c

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

Change the Anbernic RG35XX series to use the r_i2c bus for the PMIC instead of the r_rsb bus. This is to keep the device tree consistent as there are at least 3 devices (the RG35XX-SP, RG28XX, and RG40XX-H) that have an external RTC on the r_i2c bus.

[ upstream commit: c712e5d0985628b1df13930489b49b740e610a2b ]

---
 arch/arm/dts/sun50i-h700-anbernic-rg35xx-2024.dts           | 6 +++---
 .../arm64/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts    | 6 +++---
 2 files changed, 6 insertions(+), 6 deletions(-)
arch/arm/dts/sun50i-h700-anbernic-rg35xx-2024.dts +3 -3
index ee30584b6a..e2bbd22bd8 100644
@@ -201,12 +201,12 @@
 	vcc-pi-supply = <&reg_cldo3>;
 };
 
-&r_rsb {
+&r_i2c {
 	status = "okay";
 
-	axp717: pmic@3a3 {
+	axp717: pmic@34 {
 		compatible = "x-powers,axp717";
-		reg = <0x3a3>;
+		reg = <0x34>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		interrupt-parent = <&nmi_intc>;
dts/upstream/src/arm64/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts +3 -3
index ee30584b6a..e2bbd22bd8 100644
@@ -201,12 +201,12 @@
 	vcc-pi-supply = <&reg_cldo3>;
 };
 
-&r_rsb {
+&r_i2c {
 	status = "okay";
 
-	axp717: pmic@3a3 {
+	axp717: pmic@34 {
 		compatible = "x-powers,axp717";
-		reg = <0x3a3>;
+		reg = <0x34>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		interrupt-parent = <&nmi_intc>;
Signature · 1 line
2.34.1
#13 lore raw

PATCH v3 9/9 sunxi: Add support for Anbernic RG35XX-2024

In reply to Chris Morgan

From: Chris Morgan <[email protected]>

The Anbernic RG35XX series of devices are based around an Allwinner H700 SoC with 1GB of RAM, 2 SD cards, and multiple input buttons.

This bootloader has been tested on the Anbernic RG35XX-2024 and RG35XX-H, but should be suitable for the entire lineup of H700 based devices.

A future series of updates will add board selection logic to identify and load the correct device tree automatically.

---
 board/sunxi/MAINTAINERS                |  5 +++++
 configs/anbernic_rg35xx_h700_defconfig | 28 ++++++++++++++++++++++++++
 2 files changed, 33 insertions(+)
 create mode 100644 configs/anbernic_rg35xx_h700_defconfig
board/sunxi/MAINTAINERS +5 -0
index 4ad77c75f5..84799879e8 100644
@@ -132,6 +132,11 @@ M:	Paul Kocialkowski <[email protected]>
 S:	Maintained
 F:	configs/Ampe_A76_defconfig
 
+ANBERNIC RG35XX-2024
+M:	Chris Morgan <[email protected]>
+S:	Maintained
+F:	configs/anbernic_rg35xx_h700_defconfig
+
 BANANAPI M1 PLUS
 M:	Jagan Teki <[email protected]>
 S:	Maintained
configs/anbernic_rg35xx_h700_defconfig new file +28 -0
new file mode 100644
index 0000000000..57112f7d70
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h700-anbernic-rg35xx-2024"
+CONFIG_SPL=y
+CONFIG_DRAM_SUN50I_H616_DX_ODT=0x08080808
+CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e
+CONFIG_DRAM_SUN50I_H616_CA_DRI=0x0e0e
+CONFIG_DRAM_SUN50I_H616_ODT_EN=0x7887bbbb
+CONFIG_DRAM_SUN50I_H616_TPR2=0x1
+CONFIG_DRAM_SUN50I_H616_TPR6=0x40808080
+CONFIG_DRAM_SUN50I_H616_TPR10=0x402f6633
+CONFIG_DRAM_SUN50I_H616_TPR11=0x1b1f1e1c
+CONFIG_DRAM_SUN50I_H616_TPR12=0x06060606
+CONFIG_DRAM_SUN50I_H616_PHY_ADDR_MAP_1=y
+CONFIG_MACH_SUN50I_H616=y
+CONFIG_SUNXI_DRAM_H616_LPDDR4=y
+CONFIG_DRAM_CLK=672
+CONFIG_R_I2C_ENABLE=y
+CONFIG_DEFAULT_FDT_FILE="sun50i-h700-anbernic-rg35xx-2024.dtb"
+CONFIG_SPL_I2C=y
+CONFIG_SPL_SYS_I2C_LEGACY=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_SYS_I2C_SLAVE=0x7f
+CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP=y
+CONFIG_AXP717_POWER=y
+CONFIG_AXP_DCDC2_VOLT=940
+CONFIG_AXP_DCDC3_VOLT=1100
Signature · 1 line
2.34.1
#8 lore raw

Re: [PATCH V3 6/9] sunxi: Correct TPR6 parameter for H616 DRAM driver

In reply to Chris Morgan

Hi,

Quoted 6 lines · Chris Morgan

From: Chris Morgan <[email protected]>

Correct the default TPR6 parameter based on suggestion from Mikhail Kalashnikov. [1]

[1] https://lore.kernel.org/u-boot/[email protected]/

I am confused, doesn't that change belong together with the one that masks bits[23:16] instead bits[15:8]? So that the same 0xc0 end up in that register?
Mikhail, can you confirm what the intention of your reply mentioned above was? To say that the vendor code masks the different set of bits, and to stay correct we also have to adjust the TPR6 default value? For OPi Zero2W and OPi Zero3 those two bytes are the same, but for the Tanix TX1 and the default value they are not.

Cheers,
Andre

Quoted 20 lines
Fixes 4b02f0120a4b ("sunxi: H616: add LPDDR4 DRAM support")
---
  arch/arm/mach-sunxi/Kconfig | 2 +-
  1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-sunxi/Kconfig +1 -1
index 078f8c19fa..5b3571025f 100644
@@ -87,7 +87,7 @@ config DRAM_SUN50I_H616_TPR2
 
  config DRAM_SUN50I_H616_TPR6
  	hex "H616 DRAM TPR6 parameter"
-	default 0x3300c080
+	default 0x33c00080
  	help
  	  TPR6 value from vendor DRAM settings.
 
Reviewed-by on v3 5/9
#6 lore raw

Re: [PATCH V3 5/9] sunxi: H616: dram: Update mbus priorities

In reply to Chris Morgan

Hi,

Quoted 7 lines · Chris Morgan

From: Jernej Skrabec <[email protected]>

CSI1 channel (22) is missing and IOMMU (25) has priority flag set in vendor bootloader. Fix that.

While at it, replace bandwidth flag with priority since original flag has always value "true".

I cannot confirm what the vendor bootloader does, nor whether this is correct, but it seems to still work, and the patch does exactly what the commit message claims. So:

Quoted 2 lines

Cheers,
Andre

Quoted 63 lines
---
  arch/arm/mach-sunxi/dram_sun50i_h616.c | 41 +++++++++++++-------------
  1 file changed, 21 insertions(+), 20 deletions(-)
arch/arm/mach-sunxi/dram_sun50i_h616.c +21 -20
index 4782e6fe38..863c4f1d7a 100644
@@ -55,8 +55,8 @@ static void mbus_configure_port(u8 port,
  	writel_relaxed(cfg1, &mctl_com->master[port].cfg1);
  }
 
-#define MBUS_CONF(port, bwlimit, qos, acs, bwl0, bwl1, bwl2)	\
-	mbus_configure_port(port, bwlimit, false, \
+#define MBUS_CONF(port, priority, qos, acs, bwl0, bwl1, bwl2)	\
+	mbus_configure_port(port, true, priority, \
  			    MBUS_QOS_ ## qos, 0, acs, bwl0, bwl1, bwl2)
 
  static void mctl_set_master_priority(void)
@@ -68,24 +68,25 @@ static void mctl_set_master_priority(void)
  	writel(399, &mctl_com->tmr);
  	writel(BIT(16), &mctl_com->bwcr);
 
-	MBUS_CONF( 0, true, HIGHEST, 0,  256,  128,  100);
-	MBUS_CONF( 1, true,    HIGH, 0, 1536, 1400,  256);
-	MBUS_CONF( 2, true, HIGHEST, 0,  512,  256,   96);
-	MBUS_CONF( 3, true,    HIGH, 0,  256,  100,   80);
-	MBUS_CONF( 4, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF( 5, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 6, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF( 8, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(11, true,    HIGH, 0,  256,  128,  100);
-	MBUS_CONF(14, true,    HIGH, 0, 1024,  256,   64);
-	MBUS_CONF(16, true, HIGHEST, 6, 8192, 2800, 2400);
-	MBUS_CONF(21, true, HIGHEST, 6, 2048,  768,  512);
-	MBUS_CONF(25, true, HIGHEST, 0,  100,   64,   32);
-	MBUS_CONF(26, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(37, true,    HIGH, 0,  256,  128,   64);
-	MBUS_CONF(38, true,    HIGH, 2,  100,   64,   32);
-	MBUS_CONF(39, true,    HIGH, 2, 8192, 5500, 5000);
-	MBUS_CONF(40, true,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(0, false, HIGHEST, 0,  256,  128,  100);
+	MBUS_CONF(1, false,    HIGH, 0, 1536, 1400,  256);
+	MBUS_CONF(2, false, HIGHEST, 0,  512,  256,   96);
+	MBUS_CONF(3, false,    HIGH, 0,  256,  100,   80);
+	MBUS_CONF(4, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(5, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(6, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(8, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(11, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(14, false,    HIGH, 0, 1024,  256,   64);
+	MBUS_CONF(16, false, HIGHEST, 6, 8192, 2800, 2400);
+	MBUS_CONF(21, false, HIGHEST, 6, 2048,  768,  512);
+	MBUS_CONF(22, false,    HIGH, 0,  256,  128,  100);
+	MBUS_CONF(25, true,  HIGHEST, 0,  100,   64,   32);
+	MBUS_CONF(26, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(37, false,    HIGH, 0,  256,  128,   64);
+	MBUS_CONF(38, false,    HIGH, 2,  100,   64,   32);
+	MBUS_CONF(39, false,    HIGH, 2, 8192, 5500, 5000);
+	MBUS_CONF(40, false,    HIGH, 2,  100,   64,   32);
 
  	dmb();
  }
#10 lore raw

Re: [PATCH V3 7/9] arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes

In reply to Chris Morgan

Hi Chris,

Quoted 22 lines · Chris Morgan

From: Chris Morgan <[email protected]>

Add pinctrl nodes for the r_i2c node. Without the pinmux defined the r_i2c bus may fail to work, possibly if the bootloader uses rsb mode for the PMIC.

[ upstream commit: 7c9ea4ab76176f65f4f55aa144f9145a4bccaacb ]

---
 arch/arm/dts/sun50i-h616.dtsi                     | 2 ++
 dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi | 2 ++
 2 files changed, 4 insertions(+)
arch/arm/dts/sun50i-h616.dtsi +0 -0
index 921d5f61d8..41f2c23e07 100644

arch/arm/dts/sun50i-h616.dtsi line 840

Quoted 5 lines
arch/arm/dts/sun50i-h616.dtsi +2 -0
@@ -836,6 +836,8 @@
                        clocks = <&r_ccu CLK_R_APB2_I2C>;
                        dmas = <&dma 48>, <&dma 48>;
                        dma-names = "rx", "tx";
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&r_i2c_pins>;

This change is sufficient with !OF_UPSTREAM.

dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi line 840

Quoted 13 lines
arch/arm/dts/sun50i-h616.dtsi +0 -0
                        resets = <&r_ccu RST_R_APB2_I2C>;
                        status = "disabled";
                        #address-cells = <1>;
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +2 -0
index 921d5f61d8..41f2c23e07 100644
@@ -836,6 +836,8 @@
                        clocks = <&r_ccu CLK_R_APB2_I2C>;
                        dmas = <&dma 48>, <&dma 48>;
                        dma-names = "rx", "tx";
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&r_i2c_pins>;

Please don't manually patch dts/upstream subtree. It is meant to be updated only with tools/update-subtree.sh script. Also, it isn't needed as well since you haven't converted to OF_UPSTREAM at this point. Same applies to patch #8 as well.

-Sumit

Quoted 6 lines
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +0 -1
                        resets = <&r_ccu RST_R_APB2_I2C>;
                        status = "disabled";
                        #address-cells = <1>;
--

2.34.1

#11 lore raw

Re: [PATCH V3 7/9] arm64: dts: allwinner: h616: Add r_i2c pinctrl nodes

On Wed, 4 Sep 2024 10:02:16 +0530
Sumit Garg <[email protected]> wrote:

Hi,

Quoted 43 lines

Hi Chris,

Quoted 22 lines · Chris Morgan

From: Chris Morgan <[email protected]>

Add pinctrl nodes for the r_i2c node. Without the pinmux defined the r_i2c bus may fail to work, possibly if the bootloader uses rsb mode for the PMIC.

[ upstream commit: 7c9ea4ab76176f65f4f55aa144f9145a4bccaacb ]

---
 arch/arm/dts/sun50i-h616.dtsi                     | 2 ++
 dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi | 2 ++
 2 files changed, 4 insertions(+)
arch/arm/dts/sun50i-h616.dtsi +0 -0
index 921d5f61d8..41f2c23e07 100644

arch/arm/dts/sun50i-h616.dtsi line 840

Quoted 5 lines
arch/arm/dts/sun50i-h616.dtsi +2 -0
@@ -836,6 +836,8 @@
                        clocks = <&r_ccu CLK_R_APB2_I2C>;
                        dmas = <&dma 48>, <&dma 48>;
                        dma-names = "rx", "tx";
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&r_i2c_pins>;  

This change is sufficient with !OF_UPSTREAM.

Quoted 10 lines
arch/arm/dts/sun50i-h616.dtsi +0 -0
                        resets = <&r_ccu RST_R_APB2_I2C>;
                        status = "disabled";
                        #address-cells = <1>;
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +0 -0
index 921d5f61d8..41f2c23e07 100644
@@ -836,6 +836,8 @@
                        clocks = <&r_ccu CLK_R_APB2_I2C>;
                        dmas = <&dma 48>, <&dma 48>;
Quoted 8 lines

dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi line 840

Quoted 3 lines
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +2 -0
                        dma-names = "rx", "tx";
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&r_i2c_pins>;  

Please don't manually patch dts/upstream subtree. It is meant to be updated only with tools/update-subtree.sh script. Also, it isn't needed as well since you haven't converted to OF_UPSTREAM at this point. Same applies to patch #8 as well.

Yes, but the H616 OF_UPSTREAM patch is already on the list, and this series will intersect at some point. The change above is already in the queue for the kernel tree, so we will pick it up once it appears in the repo.

I will sort this all out when merging, but meanwhile it's good to have some functioning series on the list.

Cheers,
Andre

Quoted 9 lines

-Sumit

Quoted 6 lines
dts/upstream/src/arm64/allwinner/sun50i-h616.dtsi +0 -1
                        resets = <&r_ccu RST_R_APB2_I2C>;
                        status = "disabled";
                        #address-cells = <1>;
--

2.34.1