Skip to contentSkip to conversation

serial: qcom-geni: fix console corruption

PATCH Superseded Johan Hovold 5 participants 20 messages Sep 2, 2024 – Sep 6, 2024

Subsystems (4)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#5 lore raw

PATCH 2/8 serial: qcom-geni: fix false console tx restart

In reply to Johan Hovold

Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang") addressed an issue with stalled tx after the console code interrupted the last bytes of a tx command by reenabling the watermark interrupt if there is data in write buffer. This can however break software flow control by re-enabling tx after the user has stopped it.

Address the original issue by not clearing the CMD_DONE flag after polling for command completion. This allows the interrupt handler to start another transfer when the CMD_DONE interrupt has not been disabled due to flow control.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
---
 drivers/tty/serial/qcom_geni_serial.c | 13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +3 -10
index e1926124339d..0af4a93c0af5 100644
@@ -314,18 +314,16 @@ static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
 static void qcom_geni_serial_poll_tx_done(struct uart_port *uport)
 {
 	int done;
-	u32 irq_clear = M_CMD_DONE_EN;
 
 	done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
 						M_CMD_DONE_EN, true);
 	if (!done) {
 		writel(M_GENI_CMD_ABORT, uport->membase +
 						SE_GENI_M_CMD_CTRL_REG);
-		irq_clear |= M_CMD_ABORT_EN;
 		qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
 							M_CMD_ABORT_EN, true);
+		writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	}
-	writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
 }
 
 static void qcom_geni_serial_abort_rx(struct uart_port *uport)
@@ -386,6 +384,7 @@ static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
 							unsigned char c)
 {
 	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+	writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	qcom_geni_serial_setup_tx(uport, 1);
 	WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
 						M_TX_FIFO_WATERMARK_EN, true));
@@ -430,6 +429,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
 	}
 
 	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+	writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	qcom_geni_serial_setup_tx(uport, bytes_to_send);
 	for (i = 0; i < count; ) {
 		size_t chars_to_write = 0;
@@ -471,7 +471,6 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 	bool locked = true;
 	unsigned long flags;
 	u32 geni_status;
-	u32 irq_en;
 
 	WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS);
 
@@ -503,12 +502,6 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 		 * has been sent, in which case we need to look for done first.
 		 */
 		qcom_geni_serial_poll_tx_done(uport);
-
-		if (!kfifo_is_empty(&uport->state->port.xmit_fifo)) {
-			irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
-			writel(irq_en | M_TX_FIFO_WATERMARK_EN,
-					uport->membase + SE_GENI_M_IRQ_EN);
-		}
 	}
 
 	__qcom_geni_serial_console_write(uport, s, count);
Signature · 1 line
2.44.2
#8 lore raw

PATCH 4/8 serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()

In reply to Johan Hovold

From: Douglas Anderson <[email protected]>

The "offset" passed in should be unsigned since it's always a positive offset from our memory mapped IO.

The "field" should be u32 since we're anding it with a 32-bit value read from the device.

---
 drivers/tty/serial/qcom_geni_serial.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/tty/serial/qcom_geni_serial.c +1 -1
index 0af4a93c0af5..4625a2e5ebfb 100644
@@ -266,7 +266,7 @@ static bool qcom_geni_serial_secondary_active(struct uart_port *uport)
 }
 
 static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
-				int offset, int field, bool set)
+				      unsigned int offset, u32 field, bool set)
 {
 	u32 reg;
 	struct qcom_geni_serial_port *port;
Signature · 1 line
2.44.2
#9 lore raw

PATCH 5/8 serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()

In reply to Johan Hovold

From: Douglas Anderson <[email protected]>

With a small modification the qcom_geni_serial_poll_bit() function could be used to poll more than just a single bit. Let's generalize it. We'll make the qcom_geni_serial_poll_bit() into just a wrapper of the general function.

---
 drivers/tty/serial/qcom_geni_serial.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +9 -3
index 4625a2e5ebfb..7029c39a9a21 100644
@@ -265,8 +265,8 @@ static bool qcom_geni_serial_secondary_active(struct uart_port *uport)
 	return readl(uport->membase + SE_GENI_STATUS) & S_GENI_CMD_ACTIVE;
 }
 
-static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
-				      unsigned int offset, u32 field, bool set)
+static bool qcom_geni_serial_poll_bitfield(struct uart_port *uport,
+					   unsigned int offset, u32 field, u32 val)
 {
 	u32 reg;
 	struct qcom_geni_serial_port *port;
@@ -294,7 +294,7 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 	timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10;
 	while (timeout_us) {
 		reg = readl(uport->membase + offset);
-		if ((bool)(reg & field) == set)
+		if ((reg & field) == val)
 			return true;
 		udelay(10);
 		timeout_us -= 10;
@@ -302,6 +302,12 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 	return false;
 }
 
+static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
+				      unsigned int offset, u32 field, bool set)
+{
+	return qcom_geni_serial_poll_bitfield(uport, offset, field, set ? field : 0);
+}
+
 static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
 {
 	u32 m_cmd;
Signature · 1 line
2.44.2
#0 lore raw

cover serial: qcom-geni: fix console corruption

This series is a follow-on series to the lockup fixes [1] that addresses a number of issues in the Qualcomm GENI console code, including corrupt console output during boot, which is a problem for automated CI testing.

Johan

[1] https://lore.kernel.org/lkml/[email protected]/

Douglas Anderson (3):
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()

Johan Hovold (5):
serial: qcom-geni: fix fifo polling timeout
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix polled console corruption

 drivers/tty/serial/qcom_geni_serial.c | 133 +++++++++++++++-----------
 include/linux/soc/qcom/geni-se.h      |   9 ++
 2 files changed, 85 insertions(+), 57 deletions(-)
Signature · 1 line
2.44.2
#1 lore raw

PATCH 1/8 serial: qcom-geni: fix fifo polling timeout

The qcom_geni_serial_poll_bit() can be used to wait for events like command completion and is supposed to wait for the time it takes to clear a full fifo before timing out.

As noted by Doug, the current implementation does not account for start, stop and parity bits when determining the timeout. The helper also does not currently account for the shift register and the two-word intermediate transfer register.

Instead of determining the fifo timeout on every call, store the timeout when updating it in set_termios() and wait for up to 19/16 the time it takes to clear the 16 word fifo to account for the shift and intermediate registers. Note that serial core has already added a 20 ms margin to the fifo timeout.

Also note that the current uart_fifo_timeout() interface does unnecessary calculations on every call and also did not exists in earlier kernels so only store its result once. This also facilitates backports as earlier kernels can derive the timeout from uport->timeout, which has since been removed.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
---
 drivers/tty/serial/qcom_geni_serial.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +12 -12
index 69a632fefc41..e1926124339d 100644
@@ -124,7 +124,7 @@ struct qcom_geni_serial_port {
 	dma_addr_t tx_dma_addr;
 	dma_addr_t rx_dma_addr;
 	bool setup;
-	unsigned int baud;
+	unsigned long fifo_timeout_us;
 	unsigned long clk_rate;
 	void *rx_buf;
 	u32 loopback;
@@ -270,22 +270,21 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 {
 	u32 reg;
 	struct qcom_geni_serial_port *port;
-	unsigned int baud;
-	unsigned int fifo_bits;
 	unsigned long timeout_us = 20000;
 	struct qcom_geni_private_data *private_data = uport->private_data;
 
 	if (private_data->drv) {
 		port = to_dev_port(uport);
-		baud = port->baud;
-		if (!baud)
-			baud = 115200;
-		fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+
 		/*
-		 * Total polling iterations based on FIFO worth of bytes to be
-		 * sent at current baud. Add a little fluff to the wait.
+		 * Wait up to 19/16 the time it would take to clear a full
+		 * FIFO, which accounts for the three words in the shift and
+		 * intermediate registers.
+		 *
+		 * Note that fifo_timeout_us already has a 20 ms margin.
 		 */
-		timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
+		if (port->fifo_timeout_us)
+			timeout_us = 19 * port->fifo_timeout_us / 16;
 	}
 
 	/*
@@ -1248,7 +1247,6 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	qcom_geni_serial_stop_rx(uport);
 	/* baud rate */
 	baud = uart_get_baud_rate(uport, termios, old, 300, 4000000);
-	port->baud = baud;
 
 	sampling_rate = UART_OVERSAMPLING;
 	/* Sampling rate is halved for IP versions >= 2.5 */
@@ -1326,8 +1324,10 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	else
 		tx_trans_cfg |= UART_CTS_MASK;
 
-	if (baud)
+	if (baud) {
 		uart_update_timeout(uport, termios->c_cflag, baud);
+		port->fifo_timeout_us = jiffies_to_usecs(uart_fifo_timeout(uport));
+	}
 
 	if (!uart_console(uport))
 		writel(port->loopback,
Signature · 1 line
2.44.2
#7 lore raw

PATCH 3/8 soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers

In reply to Johan Hovold

From: Douglas Anderson <[email protected]>

For UART devices the M_GP_LENGTH is the TX word count. For other devices this is the transaction word count.

For UART devices the S_GP_LENGTH is the RX word count.

The IRQ_EN set/clear registers allow you to set or clear bits in the IRQ_EN register without needing a read-modify-write.

---
 include/linux/soc/qcom/geni-se.h | 9 +++++++++
 1 file changed, 9 insertions(+)
include/linux/soc/qcom/geni-se.h +9 -0
index 0f038a1a0330..c3bca9c0bf2c 100644
@@ -88,11 +88,15 @@ struct geni_se {
 #define SE_GENI_M_IRQ_STATUS		0x610
 #define SE_GENI_M_IRQ_EN		0x614
 #define SE_GENI_M_IRQ_CLEAR		0x618
+#define SE_GENI_M_IRQ_EN_SET		0x61c
+#define SE_GENI_M_IRQ_EN_CLEAR		0x620
 #define SE_GENI_S_CMD0			0x630
 #define SE_GENI_S_CMD_CTRL_REG		0x634
 #define SE_GENI_S_IRQ_STATUS		0x640
 #define SE_GENI_S_IRQ_EN		0x644
 #define SE_GENI_S_IRQ_CLEAR		0x648
+#define SE_GENI_S_IRQ_EN_SET		0x64c
+#define SE_GENI_S_IRQ_EN_CLEAR		0x650
 #define SE_GENI_TX_FIFOn		0x700
 #define SE_GENI_RX_FIFOn		0x780
 #define SE_GENI_TX_FIFO_STATUS		0x800
@@ -101,6 +105,8 @@ struct geni_se {
 #define SE_GENI_RX_WATERMARK_REG	0x810
 #define SE_GENI_RX_RFR_WATERMARK_REG	0x814
 #define SE_GENI_IOS			0x908
+#define SE_GENI_M_GP_LENGTH		0x910
+#define SE_GENI_S_GP_LENGTH		0x914
 #define SE_DMA_TX_IRQ_STAT		0xc40
 #define SE_DMA_TX_IRQ_CLR		0xc44
 #define SE_DMA_TX_FSM_RST		0xc58
@@ -234,6 +240,9 @@ struct geni_se {
 #define IO2_DATA_IN			BIT(1)
 #define RX_DATA_IN			BIT(0)
 
+/* SE_GENI_M_GP_LENGTH and SE_GENI_S_GP_LENGTH fields */
+#define GP_LENGTH			GENMASK(31, 0)
+
 /* SE_DMA_TX_IRQ_STAT Register fields */
 #define TX_DMA_DONE			BIT(0)
 #define TX_EOT				BIT(1)
Signature · 1 line
2.44.2
#10 lore raw

PATCH 6/8 serial: qcom-geni: fix console corruption

In reply to Johan Hovold

The Qualcomm serial console implementation is broken and can lose characters when the serial port is also used for tty output.

Specifically, the console code only waits for the current tx command to complete when all data has already been written to the fifo. When there are on-going longer transfers this often means that console output is lost when the console code inadvertently "hijacks" the current tx command instead of starting a new one.

This can, for example, be observed during boot when console output that should have been interspersed with init output is truncated:

	[    9.462317] qcom-snps-eusb2-hsphy fde000.phy: Registered Qcom-eUSB2 phy
	[  OK  ] Found device KBG50ZNS256G KIOXIA Wi[    9.471743ndows.
	[    9.539915] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller

Add a new state variable to track how much data has been written to the fifo and use it to determine when the fifo and shift register are both empty. This is needed since there is currently no other known way to determine when the shift register is empty.

This in turn allows the console code to interrupt long transfers without losing data.

Note that the oops-in-progress case is similarly broken as it does not cancel any active command and also waits for the wrong status flag when attempting to drain the fifo (TX_FIFO_NOT_EMPTY_EN is only set when cancelling a command leaves data in the fifo).

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Fixes 9e957a155005 ("serial: qcom-geni: Don't cancel/abort if we can't get the port lock")
---
 drivers/tty/serial/qcom_geni_serial.c | 48 ++++++++++++++-------------
 1 file changed, 25 insertions(+), 23 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +25 -23
index 7029c39a9a21..be620c5703f5 100644
@@ -131,6 +131,7 @@ struct qcom_geni_serial_port {
 	bool brk;
 
 	unsigned int tx_remaining;
+	unsigned int tx_queued;
 	int wakeup_irq;
 	bool rx_tx_swap;
 	bool cts_rts_swap;
@@ -144,6 +145,8 @@ static const struct uart_ops qcom_geni_uart_pops;
 static struct uart_driver qcom_geni_console_driver;
 static struct uart_driver qcom_geni_uart_driver;
 
+static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport);
+
 static inline struct qcom_geni_serial_port *to_dev_port(struct uart_port *uport)
 {
 	return container_of(uport, struct qcom_geni_serial_port, uport);
@@ -308,6 +311,17 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 	return qcom_geni_serial_poll_bitfield(uport, offset, field, set ? field : 0);
 }
 
+static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+	if (!qcom_geni_serial_main_active(uport))
+		return;
+
+	qcom_geni_serial_poll_bitfield(uport, SE_GENI_M_GP_LENGTH, GP_LENGTH,
+			port->tx_queued);
+}
+
 static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
 {
 	u32 m_cmd;
@@ -476,7 +490,6 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 	struct qcom_geni_serial_port *port;
 	bool locked = true;
 	unsigned long flags;
-	u32 geni_status;
 
 	WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS);
 
@@ -490,34 +503,20 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 	else
 		uart_port_lock_irqsave(uport, &flags);
 
-	geni_status = readl(uport->membase + SE_GENI_STATUS);
+	if (qcom_geni_serial_main_active(uport)) {
+		/* Wait for completion or drain FIFO */
+		if (!locked || port->tx_remaining == 0)
+			qcom_geni_serial_poll_tx_done(uport);
+		else
+			qcom_geni_serial_drain_fifo(uport);
 
-	if (!locked) {
-		/*
-		 * We can only get here if an oops is in progress then we were
-		 * unable to get the lock. This means we can't safely access
-		 * our state variables like tx_remaining. About the best we
-		 * can do is wait for the FIFO to be empty before we start our
-		 * transfer, so we'll do that.
-		 */
-		qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
-					  M_TX_FIFO_NOT_EMPTY_EN, false);
-	} else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) {
-		/*
-		 * It seems we can't interrupt existing transfers if all data
-		 * has been sent, in which case we need to look for done first.
-		 */
-		qcom_geni_serial_poll_tx_done(uport);
+		qcom_geni_serial_cancel_tx_cmd(uport);
 	}
 
 	__qcom_geni_serial_console_write(uport, s, count);
 
-
-	if (locked) {
-		if (port->tx_remaining)
-			qcom_geni_serial_setup_tx(uport, port->tx_remaining);
+	if (locked)
 		uart_port_unlock_irqrestore(uport, flags);
-	}
 }
 
 static void handle_rx_console(struct uart_port *uport, u32 bytes, bool drop)
@@ -698,6 +697,7 @@ static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport)
 	writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 
 	port->tx_remaining = 0;
+	port->tx_queued = 0;
 }
 
 static void qcom_geni_serial_handle_rx_fifo(struct uart_port *uport, bool drop)
@@ -924,6 +924,7 @@ static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport,
 	if (!port->tx_remaining) {
 		qcom_geni_serial_setup_tx(uport, pending);
 		port->tx_remaining = pending;
+		port->tx_queued = 0;
 
 		irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
 		if (!(irq_en & M_TX_FIFO_WATERMARK_EN))
@@ -932,6 +933,7 @@ static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport,
 	}
 
 	qcom_geni_serial_send_chunk_fifo(uport, chunk);
+	port->tx_queued += chunk;
 
 	/*
 	 * The tx fifo watermark is level triggered and latched. Though we had
Signature · 1 line
2.44.2
#14 lore raw

PATCH 7/8 serial: qcom-geni: disable interrupts during console writes

In reply to Johan Hovold

Disable the GENI interrupts during console writes to reduce the risk of having interrupt handlers spinning on the port lock on other cores for extended periods of time.

This can, for example, reduce the total amount of time spent in the interrupt handler during boot of the x1e80100 CRD by up to a factor nine (e.g. from 274 ms to 30 ms) while the worst case processing time drops from 19 ms to 8 ms.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
---
 drivers/tty/serial/qcom_geni_serial.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/tty/serial/qcom_geni_serial.c +9 -0
index be620c5703f5..fbed143c90a3 100644
@@ -488,6 +488,7 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 {
 	struct uart_port *uport;
 	struct qcom_geni_serial_port *port;
+	u32 m_irq_en, s_irq_en;
 	bool locked = true;
 	unsigned long flags;
 
@@ -503,6 +504,11 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 	else
 		uart_port_lock_irqsave(uport, &flags);
 
+	m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
+	s_irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN);
+	writel(0, uport->membase + SE_GENI_M_IRQ_EN);
+	writel(0, uport->membase + SE_GENI_S_IRQ_EN);
+
 	if (qcom_geni_serial_main_active(uport)) {
 		/* Wait for completion or drain FIFO */
 		if (!locked || port->tx_remaining == 0)
@@ -515,6 +521,9 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
 
 	__qcom_geni_serial_console_write(uport, s, count);
 
+	writel(m_irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+	writel(s_irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+
 	if (locked)
 		uart_port_unlock_irqrestore(uport, flags);
 }
Signature · 1 line
2.44.2
#16 lore raw

PATCH 8/8 serial: qcom-geni: fix polled console corruption

In reply to Johan Hovold

The polled UART operations are used by the kernel debugger (KDB, KGDB), which can interrupt the kernel at any point in time. The current Qualcomm GENI implementation does not really work when there is on-going serial output as it inadvertently "hijacks" the current tx command, which can result in both the initial debugger output being corrupted as well as the corruption of any on-going serial output (up to 4k characters) when execution resumes:

0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry [2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p

Fix this by making sure that the polled output implementation waits for the tx fifo to drain before cancelling any on-going longer transfers. As the polled code cannot take any locks, leave the state variables as they are and instead make sure that the interrupt handler always starts a new tx command when there is data in the write buffer.

Since the debugger can interrupt the interrupt handler when it is writing data to the tx fifo, it is currently not possible to fully prevent losing up to 64 bytes of tty output on resume.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
---
 drivers/tty/serial/qcom_geni_serial.c | 27 ++++++++++++++++++---------
 1 file changed, 18 insertions(+), 9 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +18 -9
index fbed143c90a3..cf8bafd99a09 100644
@@ -145,6 +145,7 @@ static const struct uart_ops qcom_geni_uart_pops;
 static struct uart_driver qcom_geni_console_driver;
 static struct uart_driver qcom_geni_uart_driver;
 
+static void __qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport);
 static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport);
 
 static inline struct qcom_geni_serial_port *to_dev_port(struct uart_port *uport)
@@ -403,13 +404,14 @@ static int qcom_geni_serial_get_char(struct uart_port *uport)
 static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
 							unsigned char c)
 {
-	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+	if (qcom_geni_serial_main_active(uport)) {
+		qcom_geni_serial_poll_tx_done(uport);
+		__qcom_geni_serial_cancel_tx_cmd(uport);
+	}
+
 	writel(M_CMD_DONE_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	qcom_geni_serial_setup_tx(uport, 1);
-	WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
-						M_TX_FIFO_WATERMARK_EN, true));
 	writel(c, uport->membase + SE_GENI_TX_FIFOn);
-	writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	qcom_geni_serial_poll_tx_done(uport);
 }
 #endif
@@ -688,13 +690,10 @@ static void qcom_geni_serial_stop_tx_fifo(struct uart_port *uport)
 	writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
 }
 
-static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport)
+static void __qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport)
 {
 	struct qcom_geni_serial_port *port = to_dev_port(uport);
 
-	if (!qcom_geni_serial_main_active(uport))
-		return;
-
 	geni_se_cancel_m_cmd(&port->se);
 	if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
 						M_CMD_CANCEL_EN, true)) {
@@ -704,6 +703,16 @@ static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport)
 		writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
 	}
 	writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_cancel_tx_cmd(struct uart_port *uport)
+{
+	struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+	if (!qcom_geni_serial_main_active(uport))
+		return;
+
+	__qcom_geni_serial_cancel_tx_cmd(uport);
 
 	port->tx_remaining = 0;
 	port->tx_queued = 0;
@@ -930,7 +939,7 @@ static void qcom_geni_serial_handle_tx_fifo(struct uart_port *uport,
 	if (!chunk)
 		goto out_write_wakeup;
 
-	if (!port->tx_remaining) {
+	if (!active) {
 		qcom_geni_serial_setup_tx(uport, pending);
 		port->tx_remaining = pending;
 		port->tx_queued = 0;
Signature · 1 line
2.44.2
#11 lore raw
In reply to Johan Hovold
kernel test robot noticed the following build warnings:

Hi Johan,

kernel test robot noticed the following build warnings:

[auto build test WARNING on tty/tty-testing]
[also build test WARNING on tty/tty-next tty/tty-linus driver-core/driver-core-testing driver-core/driver-core-next driver-core/driver-core-linus usb/usb-testing usb/usb-next usb/usb-linus linus/master v6.11-rc6 next-20240902] [If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Johan-Hovold/serial-qcom-geni-fix-fifo-polling-timeout/20240902-232801
base:   https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git tty-testing
patch link:    https://lore.kernel.org/r/20240902152451.862-7-johan%2Blinaro%40kernel.org
patch subject: [PATCH 6/8] serial: qcom-geni: fix console corruption
config: arc-randconfig-001-20240903 (https://download.01.org/0day-ci/archive/20240903/[email protected]/config)
compiler: arc-elf-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240903/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All warnings (new ones prefixed by >>):

>> drivers/tty/serial/qcom_geni_serial.c:314:13: warning: 'qcom_geni_serial_drain_fifo' defined but not used [-Wunused-function]

314 | static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~

vim +/qcom_geni_serial_drain_fifo +314 drivers/tty/serial/qcom_geni_serial.c

313

 > 314	static void qcom_geni_serial_drain_fifo(struct uart_port *uport)

315 {
316 struct qcom_geni_serial_port *port = to_dev_port(uport);
317
318 if (!qcom_geni_serial_main_active(uport))
319 return;
320
321 qcom_geni_serial_poll_bitfield(uport, SE_GENI_M_GP_LENGTH, GP_LENGTH,
322 port->tx_queued);
323 }
324

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
Tested-by on the v1 series
#18 lore raw
In reply to Johan Hovold
Quoted 21 lines · Johan Hovold

This series is a follow-on series to the lockup fixes [1] that addresses a number of issues in the Qualcomm GENI console code, including corrupt console output during boot, which is a problem for automated CI testing.

Johan

[1] https://lore.kernel.org/lkml/[email protected]/

Douglas Anderson (3):
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()

Johan Hovold (5):
serial: qcom-geni: fix fifo polling timeout
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix polled console corruption

Quoted 7 lines
 drivers/tty/serial/qcom_geni_serial.c | 133 +++++++++++++++-----------
 include/linux/soc/qcom/geni-se.h      |   9 ++
 2 files changed, 85 insertions(+), 57 deletions(-)
Signature · 1 line
2.44.2

This series fixes the serial issues we're seeing on the sc7180 based (sc7180-trogdor-lazor-limozeen and sc7180-trogdor-kingoftown) boards that we have hooked up to KernelCI. Out of a 10-job batch of boot tests all succeeded after the patch, whereas before most failed (7/10), due to a missing message in the serial.

Looking forward to see this landed!

Thanks,
Nícolas

#2 lore raw

Re: [PATCH 1/8] serial: qcom-geni: fix fifo polling timeout

In reply to Johan Hovold

Hi,

Quoted 61 lines · Johan Hovold

The qcom_geni_serial_poll_bit() can be used to wait for events like command completion and is supposed to wait for the time it takes to clear a full fifo before timing out.

As noted by Doug, the current implementation does not account for start, stop and parity bits when determining the timeout. The helper also does not currently account for the shift register and the two-word intermediate transfer register.

Instead of determining the fifo timeout on every call, store the timeout when updating it in set_termios() and wait for up to 19/16 the time it takes to clear the 16 word fifo to account for the shift and intermediate registers. Note that serial core has already added a 20 ms margin to the fifo timeout.

Also note that the current uart_fifo_timeout() interface does unnecessary calculations on every call and also did not exists in earlier kernels so only store its result once. This also facilitates backports as earlier kernels can derive the timeout from uport->timeout, which has since been removed.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
---
 drivers/tty/serial/qcom_geni_serial.c | 24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
drivers/tty/serial/qcom_geni_serial.c +2 -8
index 69a632fefc41..e1926124339d 100644
@@ -124,7 +124,7 @@ struct qcom_geni_serial_port {
        dma_addr_t tx_dma_addr;
        dma_addr_t rx_dma_addr;
        bool setup;
-       unsigned int baud;
+       unsigned long fifo_timeout_us;
        unsigned long clk_rate;
        void *rx_buf;
        u32 loopback;
@@ -270,22 +270,21 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 {
        u32 reg;
        struct qcom_geni_serial_port *port;
-       unsigned int baud;
-       unsigned int fifo_bits;
        unsigned long timeout_us = 20000;
        struct qcom_geni_private_data *private_data = uport->private_data;
 
        if (private_data->drv) {
                port = to_dev_port(uport);
-               baud = port->baud;
-               if (!baud)
-                       baud = 115200;
-               fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+
                /*
-                * Total polling iterations based on FIFO worth of bytes to be

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 287

Quoted 10 lines
drivers/tty/serial/qcom_geni_serial.c +7 -2
-                * sent at current baud. Add a little fluff to the wait.
+                * Wait up to 19/16 the time it would take to clear a full
+                * FIFO, which accounts for the three words in the shift and
+                * intermediate registers.
+                *
+                * Note that fifo_timeout_us already has a 20 ms margin.
                 */
-               timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
+               if (port->fifo_timeout_us)
+                       timeout_us = 19 * port->fifo_timeout_us / 16;

It made me giggle a bit that part of the justification for caching "fifo_timeout_us" was to avoid calculations each time through the function. ...but then the code does the "19/16" math here instead of just including it in the cache. ;-) ;-) ;-)

That being said, I'm not really a fan of the "19 / 16" anyway. The 16 value is calculated elsewhere in the code as:

port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); uport->fifosize =
(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;

...and here you're just hardcoding it to 16. Then there's also the fact that the "19 / 16" will also multiply the 20 ms "slop" added by uart_fifo_timeout() which doesn't seem ideal.

How about this: we just change "uport->fifosize" to account for the 3 extra words? So it can be:

((port->tx_fifo_depth + 3) * port->tx_fifo_width) / BITS_PER_BYTE;

...then the cache will be correct and everything will work out. What do you think?

-Doug

Reviewed-by on v1 2/8
#6 lore raw

Re: [PATCH 2/8] serial: qcom-geni: fix false console tx restart

In reply to Johan Hovold

Hi,

Quoted 12 lines · Johan Hovold

Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang") addressed an issue with stalled tx after the console code interrupted the last bytes of a tx command by reenabling the watermark interrupt if there is data in write buffer. This can however break software flow control by re-enabling tx after the user has stopped it.

Address the original issue by not clearing the CMD_DONE flag after polling for command completion. This allows the interrupt handler to start another transfer when the CMD_DONE interrupt has not been disabled due to flow control.

Quoted 7 lines
Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
---
 drivers/tty/serial/qcom_geni_serial.c | 13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)

This seems reasonable. I guess this can end up causing a spurious "done" interrupt to sometimes occur but that looks to be harmless.

#12 lore raw
In reply to Johan Hovold

Hi,

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 319

Quoted 7 lines · Johan Hovold
drivers/tty/serial/qcom_geni_serial.c +6 -0
+static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
+{
+       struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+       if (!qcom_geni_serial_main_active(uport))
+               return;

It seems like all callers already do the check and only ever call you if the port is active. Do you really need to re-check?

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 322

Quoted 13 lines
drivers/tty/serial/qcom_geni_serial.c +9 -0
@@ -308,6 +311,17 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
        return qcom_geni_serial_poll_bitfield(uport, offset, field, set ? field : 0);
 }
 
+static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
+{
+       struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+       if (!qcom_geni_serial_main_active(uport))
+               return;
+
+       qcom_geni_serial_poll_bitfield(uport, SE_GENI_M_GP_LENGTH, GP_LENGTH,
+                       port->tx_queued);

nit: indent "port->tx_queued" to match open parenthesis?

...also: as the kernel test robot reported, w/ certain CONFIGs this is defined / not used.

Aside from the nit / robot issue, this solution looks reasonable to me. It's been long enough that I've already paged out much of the past digging I did into this driver, but this seems like it should work. Feel free to add my Reviewed-by when the robot issue is fixed.

-Doug

Reviewed-by on v1 7/8
#15 lore raw

Re: [PATCH 7/8] serial: qcom-geni: disable interrupts during console writes

In reply to Johan Hovold

Hi,

Quoted 5 lines · Johan Hovold

Disable the GENI interrupts during console writes to reduce the risk of having interrupt handlers spinning on the port lock on other cores for extended periods of time.

Quoted 7 lines

This can, for example, reduce the total amount of time spent in the interrupt handler during boot of the x1e80100 CRD by up to a factor nine (e.g. from 274 ms to 30 ms) while the worst case processing time drops from 19 ms to 8 ms.

Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Reviewed-by on v1 8/8
#17 lore raw

Re: [PATCH 8/8] serial: qcom-geni: fix polled console corruption

In reply to Johan Hovold

Hi,

Quoted 30 lines · Johan Hovold

The polled UART operations are used by the kernel debugger (KDB, KGDB), which can interrupt the kernel at any point in time. The current Qualcomm GENI implementation does not really work when there is on-going serial output as it inadvertently "hijacks" the current tx command, which can result in both the initial debugger output being corrupted as well as the corruption of any on-going serial output (up to 4k characters) when execution resumes:

0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry [2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p

Fix this by making sure that the polled output implementation waits for the tx fifo to drain before cancelling any on-going longer transfers. As the polled code cannot take any locks, leave the state variables as they are and instead make sure that the interrupt handler always starts a new tx command when there is data in the write buffer.

Since the debugger can interrupt the interrupt handler when it is writing data to the tx fifo, it is currently not possible to fully prevent losing up to 64 bytes of tty output on resume.

Quoted 6 lines
Fixes c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
---
 drivers/tty/serial/qcom_geni_serial.c | 27 ++++++++++++++++++---------
 1 file changed, 18 insertions(+), 9 deletions(-)
#19 lore raw
In reply to Nícolas F. R. A. Prado
Quoted 5 lines · Nícolas F. R. A. Prado
Quoted 3 lines · Johan Hovold

This series is a follow-on series to the lockup fixes [1] that addresses a number of issues in the Qualcomm GENI console code, including corrupt console output during boot, which is a problem for automated CI testing.

Quoted 7 lines

This series fixes the serial issues we're seeing on the sc7180 based (sc7180-trogdor-lazor-limozeen and sc7180-trogdor-kingoftown) boards that we have hooked up to KernelCI. Out of a 10-job batch of boot tests all succeeded after the patch, whereas before most failed (7/10), due to a missing message in the serial.

Thanks for testing!

Johan

#3 lore raw

Re: [PATCH 1/8] serial: qcom-geni: fix fifo polling timeout

In reply to Doug Anderson
Quoted 48 lines · Doug Anderson
Quoted 47 lines · Johan Hovold

The qcom_geni_serial_poll_bit() can be used to wait for events like command completion and is supposed to wait for the time it takes to clear a full fifo before timing out.

As noted by Doug, the current implementation does not account for start, stop and parity bits when determining the timeout. The helper also does not currently account for the shift register and the two-word intermediate transfer register.

Instead of determining the fifo timeout on every call, store the timeout when updating it in set_termios() and wait for up to 19/16 the time it takes to clear the 16 word fifo to account for the shift and intermediate registers. Note that serial core has already added a 20 ms margin to the fifo timeout.

Also note that the current uart_fifo_timeout() interface does unnecessary calculations on every call and also did not exists in earlier kernels so only store its result once. This also facilitates backports as earlier kernels can derive the timeout from uport->timeout, which has since been removed.

drivers/tty/serial/qcom_geni_serial.c +6 -8
@@ -270,22 +270,21 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
 {
        u32 reg;
        struct qcom_geni_serial_port *port;
-       unsigned int baud;
-       unsigned int fifo_bits;
        unsigned long timeout_us = 20000;
        struct qcom_geni_private_data *private_data = uport->private_data;
 
        if (private_data->drv) {
                port = to_dev_port(uport);
-               baud = port->baud;
-               if (!baud)
-                       baud = 115200;
-               fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+
                /*
-                * Total polling iterations based on FIFO worth of bytes to be
-                * sent at current baud. Add a little fluff to the wait.
+                * Wait up to 19/16 the time it would take to clear a full
+                * FIFO, which accounts for the three words in the shift and
+                * intermediate registers.
+                *
+                * Note that fifo_timeout_us already has a 20 ms margin.
                 */
Quoted 8 lines

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 287

Quoted 3 lines
drivers/tty/serial/qcom_geni_serial.c +2 -1
-               timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
+               if (port->fifo_timeout_us)
+                       timeout_us = 19 * port->fifo_timeout_us / 16;

It made me giggle a bit that part of the justification for caching "fifo_timeout_us" was to avoid calculations each time through the function. ...but then the code does the "19/16" math here instead of just including it in the cache. ;-) ;-) ;-)

Heh, yeah, but I was really talking about uart_fifo_timeout() doing unnecessary calculations on each call (and that value used to be calculated once and stored for later use).

I also realised that we need to account for the intermediate register after I wrote the initial commit message, and before that this was just a shift and add.

Quoted 9 lines

That being said, I'm not really a fan of the "19 / 16" anyway. The 16 value is calculated elsewhere in the code as:

port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se); port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se); port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se); uport->fifosize =
(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;

Quoted 3 lines

...and here you're just hardcoding it to 16. Then there's also the fact that the "19 / 16" will also multiply the 20 ms "slop" added by uart_fifo_timeout() which doesn't seem ideal.

Indeed, and the early console code also hardcodes this to 16.

I don't care about the slop being 20 ms or 23.5, this is just a timeout for the error case.

This will over count a bit if there is uart hw with 256 B fifos, but could potentially undercount if there is hw with less than 16 words. I'm not sure if such hw exists, but I'll see what I can find out.

Quoted 7 lines

How about this: we just change "uport->fifosize" to account for the 3 extra words? So it can be:

((port->tx_fifo_depth + 3) * port->tx_fifo_width) / BITS_PER_BYTE;

...then the cache will be correct and everything will work out. What do you think?

I don't think uart_fifo_timeout traditionally accounts for the shift register and we wait up to *twice* the time it takes to clear to fifo anyway (in wait_until_sent). The intermediate register I found here could perhaps be considered part of the fifo however.

I'll give this some more thought.

Johan

#13 lore raw
In reply to Doug Anderson
Quoted 11 lines · Doug Anderson

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 319

Quoted 7 lines · Johan Hovold
drivers/tty/serial/qcom_geni_serial.c +6 -0
+static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
+{
+       struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+       if (!qcom_geni_serial_main_active(uport))
+               return;

It seems like all callers already do the check and only ever call you if the port is active. Do you really need to re-check?

I wanted to make the helper self-contained and work in both cases. But since I ended up only using this helper only in the console code and will need to move it anyway (under the console ifdef), perhaps I can consider dropping it. But then again, it's just one register read.

Quoted 4 lines
Quoted 4 lines
drivers/tty/serial/qcom_geni_serial.c +0 -0
@@ -308,6 +311,17 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
        return qcom_geni_serial_poll_bitfield(uport, offset, field, set ? field : 0);
 }
 
Quoted 11 lines

drivers/tty/serial/qcom_geni_serial.c static bool qcom_geni_serial_poll_bit(struct uart_port *uport, · line 322

Quoted 9 lines
drivers/tty/serial/qcom_geni_serial.c +9 -0
+static void qcom_geni_serial_drain_fifo(struct uart_port *uport)
+{
+       struct qcom_geni_serial_port *port = to_dev_port(uport);
+
+       if (!qcom_geni_serial_main_active(uport))
+               return;
+
+       qcom_geni_serial_poll_bitfield(uport, SE_GENI_M_GP_LENGTH, GP_LENGTH,
+                       port->tx_queued);

nit: indent "port->tx_queued" to match open parenthesis?

No, I don't use open-parenthesis alignment unless that's the (consistent) style of the code I'm changing (e.g. to avoid unnecessary realignments when symbol names change and to make a point about checkpatch --pedantic warnings not being part of the coding style).

Quoted 2 lines

...also: as the kernel test robot reported, w/ certain CONFIGs this is defined / not used.

Yes, I need to move the helper under the console ifdef. I was just waiting to see if there was any further feedback before respinning.

Quoted 4 lines

Aside from the nit / robot issue, this solution looks reasonable to me. It's been long enough that I've already paged out much of the past digging I did into this driver, but this seems like it should work. Feel free to add my Reviewed-by when the robot issue is fixed.

Thanks for reviewing.

Johan

#4 lore raw

Re: [PATCH 1/8] serial: qcom-geni: fix fifo polling timeout

In reply to Johan Hovold
Quoted 10 lines · Johan Hovold
Quoted 7 lines · Doug Anderson

How about this: we just change "uport->fifosize" to account for the 3 extra words? So it can be:

((port->tx_fifo_depth + 3) * port->tx_fifo_width) / BITS_PER_BYTE;

...then the cache will be correct and everything will work out. What do you think?

Quoted 6 lines

I don't think uart_fifo_timeout traditionally accounts for the shift register and we wait up to *twice* the time it takes to clear to fifo anyway (in wait_until_sent). The intermediate register I found here could perhaps be considered part of the fifo however.

I'll give this some more thought.

I decided to keep the fifo size as-is (e.g. as it is exported to user space) and only account for the shift and intermediate registers in the driver. I'm using the fifo size reported by the hardware to determine the timeout in v2.

Johan