Skip to contentSkip to conversation

acpi: allow building without CONFIG_HAS_IOPORT

PATCH In review Arnd Bergmann 3 participants 6 messages Oct 4, 2024 – Oct 10, 2024

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 acpi: allow building without CONFIG_HAS_IOPORT

From: Arnd Bergmann <[email protected]>

CONFIG_HAS_IOPORT will soon become optional and cause a build time failure when it is disabled but a driver calls inb()/outb(). At the moment, all architectures that can support ACPI have port I/O, but this is not necessarily the case in the future. The result is a set of errors like:

drivers/acpi/osl.c: In function 'acpi_os_read_port':
include/asm-generic/io.h:542:14: error: call to '_inb' declared with attribute error: inb()) requires CONFIG_HAS_IOPORT

In function 'acpi_ec_read_status',
inlined from 'advance_transaction' at drivers/acpi/ec.c:665:11:
include/asm-generic/io.h:542:14: error: call to '_inb' declared with attribute error: inb()) requires CONFIG_HAS_IOPORT

Since the embedded controller can only exist when port I/O is active, it makes sense to disable that code on targets that don't have it. The same is true for anything using acpi_os_read_port() and similar functions.

Add compile-time conditionals around all of those and their callers.

---
Should this be split up into smaller patches?

---
 drivers/acpi/Kconfig             | 1 +
 drivers/acpi/Makefile            | 2 +-
 drivers/acpi/acpica/Makefile     | 4 +++-
 drivers/acpi/acpica/evhandler.c  | 3 ++-
 drivers/acpi/acpica/exregion.c   | 2 ++
 drivers/acpi/acpica/hwregs.c     | 6 ++++--
 drivers/acpi/acpica/hwxface.c    | 3 ++-
 drivers/acpi/apei/apei-base.c    | 4 ++++
 drivers/acpi/bus.c               | 9 ++++++---
 drivers/acpi/cppc_acpi.c         | 6 ++++--
 drivers/acpi/osl.c               | 2 ++
 drivers/acpi/processor_perflib.c | 3 ++-
 drivers/acpi/scan.c              | 3 ++-
 13 files changed, 35 insertions(+), 13 deletions(-)
drivers/acpi/Kconfig +1 -0
index b8924077163b..5ec58c4e0332 100644
@@ -134,6 +134,7 @@ config ACPI_REV_OVERRIDE_POSSIBLE
 
 config ACPI_EC_DEBUGFS
 	tristate "EC read/write access through /sys/kernel/debug/ec"
+	depends on HAS_IOPORT
 	help
 	  Say N to disable Embedded Controller /sys/kernel/debug interface
 
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y				+= resource.o
 acpi-y				+= acpi_processor.o
 acpi-y				+= processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y				+= ec.o
+acpi-$(CONFIG_HAS_IOPORT)	+= ec.o
 acpi-$(CONFIG_ACPI_DOCK)	+= dock.o
 acpi-$(CONFIG_PCI)		+= pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)		+= pci_mcfg.o
drivers/acpi/acpica/Makefile +3 -1
index 8d18af396de9..9ba5e71348cb 100644
@@ -80,10 +80,12 @@ acpi-y +=		\
 	hwgpe.o		\
 	hwregs.o	\
 	hwsleep.o	\
-	hwvalid.o	\
 	hwxface.o	\
 	hwxfsleep.o
 
+acpi-$(CONFIG_HAS_IOPORT) += \
+	hwvalid.o
+
 acpi-$(CONFIG_PCI) += hwpci.o
 acpi-$(ACPI_FUTURE_USAGE) += hwtimer.o
 
drivers/acpi/acpica/evhandler.c +2 -1
index 1c8cb6d924df..20f61936ff9b 100644
@@ -358,12 +358,13 @@ acpi_ev_install_space_handler(struct acpi_namespace_node *node,
 			handler = acpi_ex_system_memory_space_handler;
 			setup = acpi_ev_system_memory_region_setup;
 			break;
-
+#ifdef CONFIG_HAS_IOPORT
 		case ACPI_ADR_SPACE_SYSTEM_IO:
 
 			handler = acpi_ex_system_io_space_handler;
 			setup = acpi_ev_io_space_region_setup;
 			break;
+#endif
 #ifdef ACPI_PCI_CONFIGURED
 		case ACPI_ADR_SPACE_PCI_CONFIG:
 
drivers/acpi/acpica/exregion.c +2 -0
index c49b9f8de723..8f96828614ed 100644
@@ -261,6 +261,7 @@ acpi_ex_system_memory_space_handler(u32 function,
 	return_ACPI_STATUS(status);
 }
 
+#ifdef CONFIG_HAS_IOPORT
 /*******************************************************************************
  *
  * FUNCTION:    acpi_ex_system_io_space_handler
@@ -319,6 +320,7 @@ acpi_ex_system_io_space_handler(u32 function,
 
 	return_ACPI_STATUS(status);
 }
+#endif
 
 #ifdef ACPI_PCI_CONFIGURED
 /*******************************************************************************
drivers/acpi/acpica/hwregs.c +4 -2
index f62d5d024205..845d88a01272 100644
@@ -239,7 +239,8 @@ acpi_status acpi_hw_read(u64 *value, struct acpi_generic_address *reg)
 							ACPI_DIV_8
 							(access_width),
 							&value64, access_width);
-			} else {	/* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
+			} else if (IS_ENABLED(CONFIG_HAS_IOPORT)) {
+				/* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
 
 				status = acpi_hw_read_port((acpi_io_address)
 							   address +
@@ -336,7 +337,8 @@ acpi_status acpi_hw_write(u64 value, struct acpi_generic_address *reg)
 							 ACPI_DIV_8
 							 (access_width),
 							 value64, access_width);
-			} else {	/* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
+			} else if (IS_ENABLED(CONFIG_HAS_IOPORT)) {
+				/* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
 
 				status = acpi_hw_write_port((acpi_io_address)
 							    address +
drivers/acpi/acpica/hwxface.c +2 -1
index c31f803995c6..022e706e10a1 100644
@@ -45,7 +45,8 @@ acpi_status acpi_reset(void)
 		return_ACPI_STATUS(AE_NOT_EXIST);
 	}
 
-	if (reset_reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+	if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+	    reset_reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
 		/*
 		 * For I/O space, write directly to the OSL. This bypasses the port
 		 * validation mechanism, which may block a valid write to the reset
drivers/acpi/apei/apei-base.c +4 -0
index c7c26872f4ce..19357f951bae 100644
@@ -661,12 +661,14 @@ int apei_read(u64 *val, struct acpi_generic_address *reg)
 		if (ACPI_FAILURE(status))
 			return -EIO;
 		break;
+#ifdef CONFIG_HAS_IOPORT
 	case ACPI_ADR_SPACE_SYSTEM_IO:
 		status = acpi_os_read_port(address, (u32 *)val,
 					   access_bit_width);
 		if (ACPI_FAILURE(status))
 			return -EIO;
 		break;
+#endif
 	default:
 		return -EINVAL;
 	}
@@ -694,11 +696,13 @@ int apei_write(u64 val, struct acpi_generic_address *reg)
 		if (ACPI_FAILURE(status))
 			return -EIO;
 		break;
+#ifdef CONFIG_HAS_IOPORT
 	case ACPI_ADR_SPACE_SYSTEM_IO:
 		status = acpi_os_write_port(address, val, access_bit_width);
 		if (ACPI_FAILURE(status))
 			return -EIO;
 		break;
+#endif
 	default:
 		return -EINVAL;
 	}
drivers/acpi/bus.c +6 -3
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
 	 * Do that before calling acpi_initialize_objects() which may trigger EC
 	 * address space accesses.
 	 */
-	acpi_ec_ecdt_probe();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_ecdt_probe();
 
 	status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
 	if (ACPI_FAILURE(status)) {
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
 	 * Maybe EC region is required at bus_scan/acpi_get_devices. So it
 	 * is necessary to enable it as early as possible.
 	 */
-	acpi_ec_dsdt_probe();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_dsdt_probe();
 
 	pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
 	acpi_arm_init();
 	acpi_riscv_init();
 	acpi_scan_init();
-	acpi_ec_init();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_init();
 	acpi_debugfs_init();
 	acpi_sleep_proc_init();
 	acpi_wakeup_device_init();
drivers/acpi/cppc_acpi.c +4 -2
index 5b06e236aabe..cb545cdfdc19 100644
@@ -1017,7 +1017,8 @@ static int cpc_read(int cpu, struct cpc_register_resource *reg_res, u64 *val)
 	*val = 0;
 	size = GET_BIT_WIDTH(reg);
 
-	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+	if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+	    reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
 		u32 val_u32;
 		acpi_status status;
 
@@ -1090,7 +1091,8 @@ static int cpc_write(int cpu, struct cpc_register_resource *reg_res, u64 val)
 
 	size = GET_BIT_WIDTH(reg);
 
-	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+	if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+	    reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
 		acpi_status status;
 
 		status = acpi_os_write_port((acpi_io_address)reg->address,
drivers/acpi/osl.c +2 -0
index 78a81969d90e..28eb5ff123a9 100644
@@ -638,6 +638,7 @@ u64 acpi_os_get_timer(void)
 		(ACPI_100NSEC_PER_SEC / HZ);
 }
 
+#ifdef CONFIG_HAS_IOPORT
 acpi_status acpi_os_read_port(acpi_io_address port, u32 *value, u32 width)
 {
 	u32 dummy;
@@ -680,6 +681,7 @@ acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
 }
 
 EXPORT_SYMBOL(acpi_os_write_port);
+#endif
 
 int acpi_os_read_iomem(void __iomem *virt_addr, u64 *value, u32 width)
 {
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
 	acpi_status status;
 
-	if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+	if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+	    !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
 		return 0;
 
 	pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +2 -1
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
 	if (device->handler)
 		goto ok;
 
-	acpi_ec_register_opregions(device);
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_register_opregions(device);
 
 	if (!device->flags.initialized) {
 		device->flags.power_manageable =
Signature · 1 line
2.39.2
#1 lore raw
Quoted 7 lines · Arnd Bergmann

From: Arnd Bergmann <[email protected]>

CONFIG_HAS_IOPORT will soon become optional and cause a build time failure when it is disabled but a driver calls inb()/outb(). At the moment, all architectures that can support ACPI have port I/O, but this is not necessarily the case in the future.

Can addressing this be deferred to that point?

Quoted 14 lines

The result is a set of errors like:

drivers/acpi/osl.c: In function 'acpi_os_read_port':
include/asm-generic/io.h:542:14: error: call to '_inb' declared with attribute error: inb()) requires CONFIG_HAS_IOPORT

In function 'acpi_ec_read_status',
inlined from 'advance_transaction' at drivers/acpi/ec.c:665:11:
include/asm-generic/io.h:542:14: error: call to '_inb' declared with attribute error: inb()) requires CONFIG_HAS_IOPORT

Since the embedded controller can only exist when port I/O is active, it makes sense to disable that code on targets that don't have it. The same is true for anything using acpi_os_read_port() and similar functions.

Quoted 5 lines

Add compile-time conditionals around all of those and their callers.

---
Should this be split up into smaller patches?

No need, but the ACPICA part is kind of nasty.

Quoted 65 lines
---
 drivers/acpi/Kconfig             | 1 +
 drivers/acpi/Makefile            | 2 +-
 drivers/acpi/acpica/Makefile     | 4 +++-
 drivers/acpi/acpica/evhandler.c  | 3 ++-
 drivers/acpi/acpica/exregion.c   | 2 ++
 drivers/acpi/acpica/hwregs.c     | 6 ++++--
 drivers/acpi/acpica/hwxface.c    | 3 ++-
 drivers/acpi/apei/apei-base.c    | 4 ++++
 drivers/acpi/bus.c               | 9 ++++++---
 drivers/acpi/cppc_acpi.c         | 6 ++++--
 drivers/acpi/osl.c               | 2 ++
 drivers/acpi/processor_perflib.c | 3 ++-
 drivers/acpi/scan.c              | 3 ++-
 13 files changed, 35 insertions(+), 13 deletions(-)
drivers/acpi/Kconfig +1 -0
index b8924077163b..5ec58c4e0332 100644
@@ -134,6 +134,7 @@ config ACPI_REV_OVERRIDE_POSSIBLE
 
 config ACPI_EC_DEBUGFS
        tristate "EC read/write access through /sys/kernel/debug/ec"
+       depends on HAS_IOPORT
        help
          Say N to disable Embedded Controller /sys/kernel/debug interface
 
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y                                += resource.o
 acpi-y                         += acpi_processor.o
 acpi-y                         += processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y                         += ec.o
+acpi-$(CONFIG_HAS_IOPORT)      += ec.o
 acpi-$(CONFIG_ACPI_DOCK)       += dock.o
 acpi-$(CONFIG_PCI)             += pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)                += pci_mcfg.o
drivers/acpi/acpica/Makefile +3 -1
index 8d18af396de9..9ba5e71348cb 100644
@@ -80,10 +80,12 @@ acpi-y +=           \
        hwgpe.o         \
        hwregs.o        \
        hwsleep.o       \
-       hwvalid.o       \
        hwxface.o       \
        hwxfsleep.o
 
+acpi-$(CONFIG_HAS_IOPORT) += \
+       hwvalid.o
+
 acpi-$(CONFIG_PCI) += hwpci.o
 acpi-$(ACPI_FUTURE_USAGE) += hwtimer.o
 
drivers/acpi/acpica/evhandler.c +0 -0
index 1c8cb6d924df..20f61936ff9b 100644
@@ -358,12 +358,13 @@ acpi_ev_install_space_handler(struct acpi_namespace_node *node,
                        handler = acpi_ex_system_memory_space_handler;

drivers/acpi/acpica/evhandler.c acpi_ev_install_space_handler(struct acpi_namespace_node *node, · line 367

Quoted 10 lines
drivers/acpi/acpica/evhandler.c +2 -1
                        setup = acpi_ev_system_memory_region_setup;
                        break;
-
+#ifdef CONFIG_HAS_IOPORT
                case ACPI_ADR_SPACE_SYSTEM_IO:
 
                        handler = acpi_ex_system_io_space_handler;
                        setup = acpi_ev_io_space_region_setup;
                        break;
+#endif

All changes like the above in the ACPICA code potentially increase the number of times when upstream ACPICA patches will have to be ported to Linux manually, which in turn increases the number of potential mistakes in the process.

I'd rather avoid making them, if possible.

Quoted 204 lines
drivers/acpi/acpica/evhandler.c +0 -0
 #ifdef ACPI_PCI_CONFIGURED
                case ACPI_ADR_SPACE_PCI_CONFIG:
 
drivers/acpi/acpica/exregion.c +2 -0
index c49b9f8de723..8f96828614ed 100644
@@ -261,6 +261,7 @@ acpi_ex_system_memory_space_handler(u32 function,
        return_ACPI_STATUS(status);
 }
 
+#ifdef CONFIG_HAS_IOPORT
 /*******************************************************************************
  *
  * FUNCTION:    acpi_ex_system_io_space_handler
@@ -319,6 +320,7 @@ acpi_ex_system_io_space_handler(u32 function,
 
        return_ACPI_STATUS(status);
 }
+#endif
 
 #ifdef ACPI_PCI_CONFIGURED
 /*******************************************************************************
drivers/acpi/acpica/hwregs.c +4 -2
index f62d5d024205..845d88a01272 100644
@@ -239,7 +239,8 @@ acpi_status acpi_hw_read(u64 *value, struct acpi_generic_address *reg)
                                                        ACPI_DIV_8
                                                        (access_width),
                                                        &value64, access_width);
-                       } else {        /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
+                       } else if (IS_ENABLED(CONFIG_HAS_IOPORT)) {
+                               /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
 
                                status = acpi_hw_read_port((acpi_io_address)
                                                           address +
@@ -336,7 +337,8 @@ acpi_status acpi_hw_write(u64 value, struct acpi_generic_address *reg)
                                                         ACPI_DIV_8
                                                         (access_width),
                                                         value64, access_width);
-                       } else {        /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
+                       } else if (IS_ENABLED(CONFIG_HAS_IOPORT)) {
+                               /* ACPI_ADR_SPACE_SYSTEM_IO, validated earlier */
 
                                status = acpi_hw_write_port((acpi_io_address)
                                                            address +
drivers/acpi/acpica/hwxface.c +2 -1
index c31f803995c6..022e706e10a1 100644
@@ -45,7 +45,8 @@ acpi_status acpi_reset(void)
                return_ACPI_STATUS(AE_NOT_EXIST);
        }
 
-       if (reset_reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+       if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+           reset_reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
                /*
                 * For I/O space, write directly to the OSL. This bypasses the port
                 * validation mechanism, which may block a valid write to the reset
drivers/acpi/apei/apei-base.c +4 -0
index c7c26872f4ce..19357f951bae 100644
@@ -661,12 +661,14 @@ int apei_read(u64 *val, struct acpi_generic_address *reg)
                if (ACPI_FAILURE(status))
                        return -EIO;
                break;
+#ifdef CONFIG_HAS_IOPORT
        case ACPI_ADR_SPACE_SYSTEM_IO:
                status = acpi_os_read_port(address, (u32 *)val,
                                           access_bit_width);
                if (ACPI_FAILURE(status))
                        return -EIO;
                break;
+#endif
        default:
                return -EINVAL;
        }
@@ -694,11 +696,13 @@ int apei_write(u64 val, struct acpi_generic_address *reg)
                if (ACPI_FAILURE(status))
                        return -EIO;
                break;
+#ifdef CONFIG_HAS_IOPORT
        case ACPI_ADR_SPACE_SYSTEM_IO:
                status = acpi_os_write_port(address, val, access_bit_width);
                if (ACPI_FAILURE(status))
                        return -EIO;
                break;
+#endif
        default:
                return -EINVAL;
        }
drivers/acpi/bus.c +6 -3
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
         * Do that before calling acpi_initialize_objects() which may trigger EC
         * address space accesses.
         */
-       acpi_ec_ecdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_ecdt_probe();
 
        status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
        if (ACPI_FAILURE(status)) {
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
         * Maybe EC region is required at bus_scan/acpi_get_devices. So it
         * is necessary to enable it as early as possible.
         */
-       acpi_ec_dsdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_dsdt_probe();
 
        pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
        acpi_arm_init();
        acpi_riscv_init();
        acpi_scan_init();
-       acpi_ec_init();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_init();
        acpi_debugfs_init();
        acpi_sleep_proc_init();
        acpi_wakeup_device_init();
drivers/acpi/cppc_acpi.c +4 -2
index 5b06e236aabe..cb545cdfdc19 100644
@@ -1017,7 +1017,8 @@ static int cpc_read(int cpu, struct cpc_register_resource *reg_res, u64 *val)
        *val = 0;
        size = GET_BIT_WIDTH(reg);
 
-       if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+       if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+           reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
                u32 val_u32;
                acpi_status status;
 
@@ -1090,7 +1091,8 @@ static int cpc_write(int cpu, struct cpc_register_resource *reg_res, u64 val)
 
        size = GET_BIT_WIDTH(reg);
 
-       if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+       if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+           reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
                acpi_status status;
 
                status = acpi_os_write_port((acpi_io_address)reg->address,
drivers/acpi/osl.c +2 -0
index 78a81969d90e..28eb5ff123a9 100644
@@ -638,6 +638,7 @@ u64 acpi_os_get_timer(void)
                (ACPI_100NSEC_PER_SEC / HZ);
 }
 
+#ifdef CONFIG_HAS_IOPORT
 acpi_status acpi_os_read_port(acpi_io_address port, u32 *value, u32 width)
 {
        u32 dummy;
@@ -680,6 +681,7 @@ acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
 }
 
 EXPORT_SYMBOL(acpi_os_write_port);
+#endif
 
 int acpi_os_read_iomem(void __iomem *virt_addr, u64 *value, u32 width)
 {
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
        acpi_status status;
 
-       if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+           !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
                return 0;
 
        pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +2 -2
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
        if (device->handler)
                goto ok;
 
-       acpi_ec_register_opregions(device);
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_register_opregions(device);
 
        if (!device->flags.initialized) {
                device->flags.power_manageable =
--

2.39.2

#2 lore raw
Quoted 10 lines · Rafael J. Wysocki
Quoted 7 lines · Arnd Bergmann

From: Arnd Bergmann <[email protected]>

CONFIG_HAS_IOPORT will soon become optional and cause a build time failure when it is disabled but a driver calls inb()/outb(). At the moment, all architectures that can support ACPI have port I/O, but this is not necessarily the case in the future.

Can addressing this be deferred to that point?

Yes. I would like to have all of arm64 and riscv be able to turn off HAS_IOPORT eventually, but nothing depends on doing this when ACPI is enabled.

Quoted 5 lines
Quoted 5 lines

Since the embedded controller can only exist when port I/O is active, it makes sense to disable that code on targets that don't have it. The same is true for anything using acpi_os_read_port() and similar functions.

Quoted 7 lines
Quoted 5 lines

Add compile-time conditionals around all of those and their callers.

---
Should this be split up into smaller patches?

No need, but the ACPICA part is kind of nasty.

Right, I see.

Quoted 20 lines
Quoted 4 lines
drivers/acpi/acpica/evhandler.c +0 -0
@@ -358,12 +358,13 @@ acpi_ev_install_space_handler(struct acpi_namespace_node *node,
                        handler = acpi_ex_system_memory_space_handler;

drivers/acpi/acpica/evhandler.c acpi_ev_install_space_handler(struct acpi_namespace_node *node, · line 367

Quoted 10 lines
drivers/acpi/acpica/evhandler.c +2 -1
                        setup = acpi_ev_system_memory_region_setup;
                        break;
-
+#ifdef CONFIG_HAS_IOPORT
                case ACPI_ADR_SPACE_SYSTEM_IO:
 
                        handler = acpi_ex_system_io_space_handler;
                        setup = acpi_ev_io_space_region_setup;
                        break;
+#endif

All changes like the above in the ACPICA code potentially increase the number of times when upstream ACPICA patches will have to be ported to Linux manually, which in turn increases the number of potential mistakes in the process.

Quoted 1 line

I'd rather avoid making them, if possible.

Understood. Does that mean that on the flip-side we can change the drivers/acpi/osl.c portion to turn acpi_os_read_port() and acpi_os_write_port() into a runtime error for configurations without port I/O, without causing the same maintenance overhead?

The version below builds fine and doesn't touch acpica but it's a bit harder to predict what would happen at runtime.

Arnd

drivers/acpi/Kconfig +1 -0
index b8924077163b..5ec58c4e0332 100644
@@ -134,6 +134,7 @@ config ACPI_REV_OVERRIDE_POSSIBLE
 
 config ACPI_EC_DEBUGFS
 	tristate "EC read/write access through /sys/kernel/debug/ec"
+	depends on HAS_IOPORT
 	help
 	  Say N to disable Embedded Controller /sys/kernel/debug interface
 
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y				+= resource.o
 acpi-y				+= acpi_processor.o
 acpi-y				+= processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y				+= ec.o
+acpi-$(CONFIG_HAS_IOPORT)	+= ec.o
 acpi-$(CONFIG_ACPI_DOCK)	+= dock.o
 acpi-$(CONFIG_PCI)		+= pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)		+= pci_mcfg.o
drivers/acpi/bus.c +6 -3
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
 	 * Do that before calling acpi_initialize_objects() which may trigger EC
 	 * address space accesses.
 	 */
-	acpi_ec_ecdt_probe();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_ecdt_probe();
 
 	status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
 	if (ACPI_FAILURE(status)) {
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
 	 * Maybe EC region is required at bus_scan/acpi_get_devices. So it
 	 * is necessary to enable it as early as possible.
 	 */
-	acpi_ec_dsdt_probe();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_dsdt_probe();
 
 	pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
 	acpi_arm_init();
 	acpi_riscv_init();
 	acpi_scan_init();
-	acpi_ec_init();
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_init();
 	acpi_debugfs_init();
 	acpi_sleep_proc_init();
 	acpi_wakeup_device_init();
drivers/acpi/cppc_acpi.c +4 -2
index b73b3aa92f3f..326b73ae77a9 100644
@@ -1017,7 +1017,8 @@ static int cpc_read(int cpu, struct cpc_register_resource *reg_res, u64 *val)
 	*val = 0;
 	size = GET_BIT_WIDTH(reg);
 
-	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+	if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+	    reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
 		u32 val_u32;
 		acpi_status status;
 
@@ -1090,7 +1091,8 @@ static int cpc_write(int cpu, struct cpc_register_resource *reg_res, u64 val)
 
 	size = GET_BIT_WIDTH(reg);
 
-	if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+	if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+	    reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
 		acpi_status status;
 
 		status = acpi_os_write_port((acpi_io_address)reg->address,
drivers/acpi/osl.c +8 -0
index 78a81969d90e..04d3864073ba 100644
@@ -642,6 +642,11 @@ acpi_status acpi_os_read_port(acpi_io_address port, u32 *value, u32 width)
 {
 	u32 dummy;
 
+	if (!IS_ENABLED(CONFIG_HAS_IOPORT)) {
+		*value = BIT_MASK(width);
+		return AE_NOT_IMPLEMENTED;
+	}
+
 	if (value)
 		*value = 0;
 	else
@@ -665,6 +670,9 @@ EXPORT_SYMBOL(acpi_os_read_port);
 
 acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
 {
+	if (!IS_ENABLED(CONFIG_HAS_IOPORT))
+		return AE_NOT_IMPLEMENTED;
+
 	if (width <= 8) {
 		outb(value, port);
 	} else if (width <= 16) {
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
 	acpi_status status;
 
-	if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+	if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+	    !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
 		return 0;
 
 	pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +2 -1
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
 	if (device->handler)
 		goto ok;
 
-	acpi_ec_register_opregions(device);
+	if (IS_ENABLED(CONFIG_HAS_IOPORT))
+		acpi_ec_register_opregions(device);
 
 	if (!device->flags.initialized) {
 		device->flags.power_manageable =
#3 lore raw
Quoted 52 lines · Arnd Bergmann
Quoted 10 lines · Rafael J. Wysocki
Quoted 7 lines · Arnd Bergmann

From: Arnd Bergmann <[email protected]>

CONFIG_HAS_IOPORT will soon become optional and cause a build time failure when it is disabled but a driver calls inb()/outb(). At the moment, all architectures that can support ACPI have port I/O, but this is not necessarily the case in the future.

Can addressing this be deferred to that point?

Yes. I would like to have all of arm64 and riscv be able to turn off HAS_IOPORT eventually, but nothing depends on doing this when ACPI is enabled.

Quoted 5 lines
Quoted 5 lines

Since the embedded controller can only exist when port I/O is active, it makes sense to disable that code on targets that don't have it. The same is true for anything using acpi_os_read_port() and similar functions.

Quoted 7 lines
Quoted 5 lines

Add compile-time conditionals around all of those and their callers.

---
Should this be split up into smaller patches?

No need, but the ACPICA part is kind of nasty.

Right, I see.

Quoted 20 lines
Quoted 4 lines
drivers/acpi/acpica/evhandler.c +0 -0
@@ -358,12 +358,13 @@ acpi_ev_install_space_handler(struct acpi_namespace_node *node,
                        handler = acpi_ex_system_memory_space_handler;

drivers/acpi/acpica/evhandler.c acpi_ev_install_space_handler(struct acpi_namespace_node *node, · line 367

Quoted 10 lines
drivers/acpi/acpica/evhandler.c +2 -1
                        setup = acpi_ev_system_memory_region_setup;
                        break;
-
+#ifdef CONFIG_HAS_IOPORT
                case ACPI_ADR_SPACE_SYSTEM_IO:
 
                        handler = acpi_ex_system_io_space_handler;
                        setup = acpi_ev_io_space_region_setup;
                        break;
+#endif

All changes like the above in the ACPICA code potentially increase the number of times when upstream ACPICA patches will have to be ported to Linux manually, which in turn increases the number of potential mistakes in the process.

Quoted 6 lines
Quoted 1 line

I'd rather avoid making them, if possible.

Understood. Does that mean that on the flip-side we can change the drivers/acpi/osl.c portion to turn acpi_os_read_port() and acpi_os_write_port() into a runtime error for configurations without port I/O, without causing the same maintenance overhead?

Yes, that can be done.

Quoted 2 lines

The version below builds fine and doesn't touch acpica but it's a bit harder to predict what would happen at runtime.

Sure.

Quoted 40 lines
drivers/acpi/Kconfig +1 -0
index b8924077163b..5ec58c4e0332 100644
@@ -134,6 +134,7 @@ config ACPI_REV_OVERRIDE_POSSIBLE
 
 config ACPI_EC_DEBUGFS
        tristate "EC read/write access through /sys/kernel/debug/ec"
+       depends on HAS_IOPORT
        help
          Say N to disable Embedded Controller /sys/kernel/debug interface
 
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y                                += resource.o
 acpi-y                         += acpi_processor.o
 acpi-y                         += processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y                         += ec.o
+acpi-$(CONFIG_HAS_IOPORT)      += ec.o
 acpi-$(CONFIG_ACPI_DOCK)       += dock.o
 acpi-$(CONFIG_PCI)             += pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)                += pci_mcfg.o
drivers/acpi/bus.c +2 -1
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
         * Do that before calling acpi_initialize_objects() which may trigger EC
         * address space accesses.
         */
-       acpi_ec_ecdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_ecdt_probe();
 
        status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
        if (ACPI_FAILURE(status)) {

drivers/acpi/bus.c static int __init acpi_bus_init(void) · line 1396

Quoted 6 lines
drivers/acpi/bus.c +2 -1
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
         * Maybe EC region is required at bus_scan/acpi_get_devices. So it
         * is necessary to enable it as early as possible.
         */
-       acpi_ec_dsdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_dsdt_probe();

The above two changes mean that it is not necessary to compile either acpi_ec_ecdt_probe() or acpi_ec_dsdt_probe() at all if CONFIG_HAS_IOPORT is not enabled.

drivers/acpi/bus.c static int __init acpi_init(void) · line 1470

Quoted 10 lines
drivers/acpi/bus.c +2 -1
        pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
        acpi_arm_init();
        acpi_riscv_init();
        acpi_scan_init();
-       acpi_ec_init();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_init();

And this means that the whole EC driver is not going to work at all then.

Quoted 44 lines
drivers/acpi/bus.c +0 -0
        acpi_debugfs_init();
        acpi_sleep_proc_init();
        acpi_wakeup_device_init();
drivers/acpi/cppc_acpi.c +4 -2
index b73b3aa92f3f..326b73ae77a9 100644
@@ -1017,7 +1017,8 @@ static int cpc_read(int cpu, struct cpc_register_resource *reg_res, u64 *val)
        *val = 0;
        size = GET_BIT_WIDTH(reg);
 
-       if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+       if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+           reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
                u32 val_u32;
                acpi_status status;
 
@@ -1090,7 +1091,8 @@ static int cpc_write(int cpu, struct cpc_register_resource *reg_res, u64 val)
 
        size = GET_BIT_WIDTH(reg);
 
-       if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
+       if (IS_ENABLED(CONFIG_HAS_IOPORT) &&
+           reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
                acpi_status status;
 
                status = acpi_os_write_port((acpi_io_address)reg->address,
drivers/acpi/osl.c +5 -0
index 78a81969d90e..04d3864073ba 100644
@@ -642,6 +642,11 @@ acpi_status acpi_os_read_port(acpi_io_address port, u32 *value, u32 width)
 {
        u32 dummy;
 
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT)) {
+               *value = BIT_MASK(width);
+               return AE_NOT_IMPLEMENTED;
+       }
+
        if (value)
                *value = 0;
        else

drivers/acpi/osl.c EXPORT_SYMBOL(acpi_os_read_port); · line 678

Quoted 9 lines
drivers/acpi/osl.c +3 -0
@@ -665,6 +670,9 @@ EXPORT_SYMBOL(acpi_os_read_port);
 
 acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
 {
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT))
+               return AE_NOT_IMPLEMENTED;
+
        if (width <= 8) {
                outb(value, port);
        } else if (width <= 16) {

The above two changes look reasonable to me.

drivers/acpi/processor_perflib.c int acpi_processor_pstate_control(void) · line 460

Quoted 12 lines
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
        acpi_status status;
 
-       if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+           !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
                return 0;

All of the existing callers of acpi_processor_pstate_control() are x86 which has CONFIG_HAS_IOPORT AFAICS.

And if you care about the code size, acpi_processor_notify_smm() can go away for !CONFIG_HAS_IOPORT too.

drivers/acpi/scan.c static int acpi_bus_attach(struct acpi_device *device, void *first_pass) · line 2297

Quoted 12 lines
drivers/acpi/processor_perflib.c +0 -0
        pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +2 -1
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
        if (device->handler)
                goto ok;
 
-       acpi_ec_register_opregions(device);
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_register_opregions(device);

I'd rather have an empty stub of acpi_ec_register_opregions() for !CONFIG_HAS_IOPORT instead.

Quoted 3 lines
drivers/acpi/scan.c +0 -0
        if (!device->flags.initialized) {
                device->flags.power_manageable =
#4 lore raw
Quoted 26 lines · Rafael J. Wysocki
Quoted 25 lines · Arnd Bergmann
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y                                += resource.o
 acpi-y                         += acpi_processor.o
 acpi-y                         += processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y                         += ec.o
+acpi-$(CONFIG_HAS_IOPORT)      += ec.o
 acpi-$(CONFIG_ACPI_DOCK)       += dock.o
 acpi-$(CONFIG_PCI)             += pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)                += pci_mcfg.o
drivers/acpi/bus.c +2 -1
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
         * Do that before calling acpi_initialize_objects() which may trigger EC
         * address space accesses.
         */
-       acpi_ec_ecdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_ecdt_probe();
 
Quoted 13 lines

drivers/acpi/bus.c static int __init acpi_bus_init(void) · line 1396

Quoted 9 lines
drivers/acpi/bus.c +2 -1
        status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
        if (ACPI_FAILURE(status)) {
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
         * Maybe EC region is required at bus_scan/acpi_get_devices. So it
         * is necessary to enable it as early as possible.
         */
-       acpi_ec_dsdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_dsdt_probe();

The above two changes mean that it is not necessary to compile either acpi_ec_ecdt_probe() or acpi_ec_dsdt_probe() at all if CONFIG_HAS_IOPORT is not enabled.

Correct, this is a result of removing ec.o from the list of objects.

Quoted 11 lines

drivers/acpi/bus.c static int __init acpi_init(void) · line 1470

Quoted 9 lines
drivers/acpi/bus.c +2 -1
        pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
        acpi_arm_init();
        acpi_riscv_init();
        acpi_scan_init();
-       acpi_ec_init();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_init();

And this means that the whole EC driver is not going to work at all then.

Correct. The way I read ec.c it makes no sense if acpi_ec_write_cmd() and acpi_ec_write_data() don't actually access the registers. Is there anything in ec.c that still makes sense without port I/O?

Quoted 28 lines

drivers/acpi/processor_perflib.c int acpi_processor_pstate_control(void) · line 460

Quoted 12 lines
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
        acpi_status status;
 
-       if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+           !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
                return 0;

All of the existing callers of acpi_processor_pstate_control() are x86 which has CONFIG_HAS_IOPORT AFAICS.

And if you care about the code size, acpi_processor_notify_smm() can go away for !CONFIG_HAS_IOPORT too.

Quoted 9 lines
drivers/acpi/processor_perflib.c +0 -0
        pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +0 -0
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
        if (device->handler)
                goto ok;
 
Quoted 6 lines

drivers/acpi/scan.c static int acpi_bus_attach(struct acpi_device *device, void *first_pass) · line 2297

Quoted 3 lines
drivers/acpi/scan.c +2 -1
-       acpi_ec_register_opregions(device);
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_register_opregions(device);

I'd rather have an empty stub of acpi_ec_register_opregions() for !CONFIG_HAS_IOPORT instead.

Fair enough. Should I add stubs for all the global EC functions then? I also wonder if there should be a separate CONFIG_ACPI_EC symbol that allows the EC logic to be turned off on non-x86 architectures even when HAS_IOPORT is otherwise enabled.

Arnd

#5 lore raw
Quoted 88 lines · Arnd Bergmann
Quoted 26 lines · Rafael J. Wysocki
Quoted 25 lines · Arnd Bergmann
drivers/acpi/Makefile +1 -1
index 61ca4afe83dc..132357815324 100644
@@ -41,7 +41,7 @@ acpi-y                                += resource.o
 acpi-y                         += acpi_processor.o
 acpi-y                         += processor_core.o
 acpi-$(CONFIG_ARCH_MIGHT_HAVE_ACPI_PDC) += processor_pdc.o
-acpi-y                         += ec.o
+acpi-$(CONFIG_HAS_IOPORT)      += ec.o
 acpi-$(CONFIG_ACPI_DOCK)       += dock.o
 acpi-$(CONFIG_PCI)             += pci_root.o pci_link.o pci_irq.o
 obj-$(CONFIG_ACPI_MCFG)                += pci_mcfg.o
drivers/acpi/bus.c +2 -1
index 16917dc3ad60..535d6a72ce1b 100644
@@ -1356,7 +1356,8 @@ static int __init acpi_bus_init(void)
         * Do that before calling acpi_initialize_objects() which may trigger EC
         * address space accesses.
         */
-       acpi_ec_ecdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_ecdt_probe();
 
Quoted 13 lines

drivers/acpi/bus.c static int __init acpi_bus_init(void) · line 1396

Quoted 9 lines
drivers/acpi/bus.c +2 -1
        status = acpi_enable_subsystem(ACPI_NO_ACPI_ENABLE);
        if (ACPI_FAILURE(status)) {
@@ -1391,7 +1392,8 @@ static int __init acpi_bus_init(void)
         * Maybe EC region is required at bus_scan/acpi_get_devices. So it
         * is necessary to enable it as early as possible.
         */
-       acpi_ec_dsdt_probe();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_dsdt_probe();

The above two changes mean that it is not necessary to compile either acpi_ec_ecdt_probe() or acpi_ec_dsdt_probe() at all if CONFIG_HAS_IOPORT is not enabled.

Correct, this is a result of removing ec.o from the list of objects.

Quoted 11 lines

drivers/acpi/bus.c static int __init acpi_init(void) · line 1470

Quoted 9 lines
drivers/acpi/bus.c +2 -1
        pr_info("Interpreter enabled\n");
 
@@ -1464,7 +1466,8 @@ static int __init acpi_init(void)
        acpi_arm_init();
        acpi_riscv_init();
        acpi_scan_init();
-       acpi_ec_init();
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_init();

And this means that the whole EC driver is not going to work at all then.

Correct. The way I read ec.c it makes no sense if acpi_ec_write_cmd() and acpi_ec_write_data() don't actually access the registers. Is there anything in ec.c that still makes sense without port I/O?

Quoted 28 lines

drivers/acpi/processor_perflib.c int acpi_processor_pstate_control(void) · line 460

Quoted 12 lines
drivers/acpi/processor_perflib.c +2 -1
index 4265814c74f8..8be453d89ef8 100644
@@ -455,7 +455,8 @@ int acpi_processor_pstate_control(void)
 {
        acpi_status status;
 
-       if (!acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
+       if (!IS_ENABLED(CONFIG_HAS_IOPORT) ||
+           !acpi_gbl_FADT.smi_command || !acpi_gbl_FADT.pstate_control)
                return 0;

All of the existing callers of acpi_processor_pstate_control() are x86 which has CONFIG_HAS_IOPORT AFAICS.

And if you care about the code size, acpi_processor_notify_smm() can go away for !CONFIG_HAS_IOPORT too.

Quoted 9 lines
drivers/acpi/processor_perflib.c +0 -0
        pr_debug("Writing pstate_control [0x%x] to smi_command [0x%x]\n",
drivers/acpi/scan.c +0 -0
index 7ecc401fb97f..9d5e6dd542bf 100644
@@ -2293,7 +2293,8 @@ static int acpi_bus_attach(struct acpi_device *device, void *first_pass)
        if (device->handler)
                goto ok;
 
Quoted 8 lines
Quoted 6 lines

drivers/acpi/scan.c static int acpi_bus_attach(struct acpi_device *device, void *first_pass) · line 2297

Quoted 3 lines
drivers/acpi/scan.c +2 -1
-       acpi_ec_register_opregions(device);
+       if (IS_ENABLED(CONFIG_HAS_IOPORT))
+               acpi_ec_register_opregions(device);

I'd rather have an empty stub of acpi_ec_register_opregions() for !CONFIG_HAS_IOPORT instead.

Fair enough. Should I add stubs for all the global EC functions then?

Yes, please.

Quoted 3 lines

I also wonder if there should be a separate CONFIG_ACPI_EC symbol that allows the EC logic to be turned off on non-x86 architectures even when HAS_IOPORT is otherwise enabled.

Yes, CONFIG_ACPI_EC would make sense IMV.

Thanks!