riscv: dts: starfive: jh7110-milkv-mars: set host mode and vbus pin for on-chip USB 2.0
Subsystems (3)
PATCH 1/1 riscv: dts: starfive: jh7110-milkv-mars: set host mode and vbus pin for on-chip USB 2.0
Enable host mode USB for Milk-V Mars by setting host mode and connect vbus pinctrl.
Note that testing this functionality depends on two features:
1. commit e10c52e7e064038d9bd67b20bf4ce92077d7d84e "phy: starfive:
jh7110-usb: Fix link configuration to controller"
2. Setting the USB over-current register to disable. This is done at bootloader phase, for example U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
If the over-current register is not prepared for us then the result is no change in functional outcome with this patch applied; there is an error visible to the user and usb configuration fails (same as it is now).
--- .../boot/dts/starfive/jh7110-milkv-mars.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts +17 -1
@@ -53,7 +53,23 @@ &spi0 { status = "okay"; }; +&sysgpio { + usb_pins: usb0-0 { + driver-vbus-pin { + pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS, + GPOEN_ENABLE, + GPI_NONE)>; + bias-disable; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + &usb0 { - dr_mode = "peripheral"; + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&usb_pins>; status = "okay"; };
Signature · 7 lines
2.45.2 _______________________________________________ linux-riscv mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-riscv
Rob Herring (Arm)
maintainerQuoted 12 lines · E Shattow
Enable host mode USB for Milk-V Mars by setting host mode and connect vbus pinctrl.
Note that testing this functionality depends on two features:
1. commit
e10c52e7e064038d9bd67b20bf4ce92077d7d84e"phy: starfive:
jh7110-usb: Fix link configuration to controller"2. Setting the USB over-current register to disable. This is done at bootloader phase, for example U-Boot:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
Quoted 9 lines
If the over-current register is not prepared for us then the result is no change in functional outcome with this patch applied; there is an error visible to the user and usb configuration fails (same as it is now).
Signed-off-by E Shattow <[email protected]>--- .../boot/dts/starfive/jh7110-milkv-mars.dts | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
My bot found new DTB warnings on the .dts files added or changed in this series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y starfive/jh7110-milkv-mars.dtb' for [email protected]:
arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dtb: pinctrl@13040000: usb0-0: 'driver-vbus-pin' does not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#