vfio/pci: Properly hide first-in-list PCIe extended capability
Subsystems (2)
PATCH 1/1 vfio/pci: Properly hide first-in-list PCIe extended capability
There are cases where a PCIe extended capability should be hidden from the user. For example, an unknown capability (i.e., capability with ID greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally chosen to be hidden from the user.
Hiding a capability is done by virtualizing and modifying the 'Next Capability Offset' field of the previous capability so it points to the capability after the one that should be hidden.
The special case where the first capability in the list should be hidden is handled differently because there is no previous capability that can be modified. In this case, the capability ID and version are zeroed while leaving the next pointer intact. This hides the capability and leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done properly, as struct vfio_pci_core_device->pci_config_map is still set to the capability ID. If the first capability in the list is unknown, the following warning [1] is triggered and an out-of-bounds access to ecap_perms array occurs when vfio_config_do_rw() later uses pci_config_map to pick the right permissions.
Fix it by defining a new special capability PCI_CAP_ID_FIRST_HIDDEN, that represents a hidden extended capability that is located first in the extended capability list, and set pci_config_map to it in the above case.
[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1 (snip) Call Trace: <TASK> ? show_regs+0x69/0x80 ? __warn+0x8d/0x140 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? report_bug+0x18f/0x1a0 ? handle_bug+0x63/0xa0 ? exc_invalid_op+0x19/0x70 ? asm_exc_invalid_op+0x1b/0x20 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core] vfio_pci_rw+0x101/0x1b0 [vfio_pci_core] vfio_pci_core_read+0x1d/0x30 [vfio_pci_core] vfio_device_fops_read+0x27/0x40 [vfio] vfs_read+0xbd/0x340 ? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio] ? __rseq_handle_notify_resume+0xa4/0x4b0 __x64_sys_pread64+0x96/0xc0 x64_sys_call+0x1c3d/0x20d0 do_syscall_64+0x4d/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e
--- drivers/vfio/pci/vfio_pci_priv.h | 1 + drivers/vfio/pci/vfio_pci_config.c | 18 +++++++++++++----- 2 files changed, 14 insertions(+), 5 deletions(-)
drivers/vfio/pci/vfio_pci_priv.h +1 -0
@@ -7,6 +7,7 @@/* Special capability IDs predefined access */ #define PCI_CAP_ID_INVALID 0xFF/* default raw access */ #define PCI_CAP_ID_INVALID_VIRT 0xFE/* default virt access */ +#define PCI_CAP_ID_FIRST_HIDDEN 0xFD/* default direct access */ /* Cap maximum number of ioeventfds per device (arbitrary) */ #define VFIO_PCI_IOEVENTFD_MAX 1000
drivers/vfio/pci/vfio_pci_config.c +13 -5
@@ -320,6 +320,10 @@ static struct perm_bits cap_perms[PCI_CAP_ID_MAX + 1] = {static struct perm_bits ecap_perms[PCI_EXT_CAP_ID_MAX +1 ] = { [0 ...PCI_EXT_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } }; +/* Perms for a first-in-list hidden extended capability */ +static struct perm_bits hidden_ecap_perm = { + .readfn = vfio_direct_config_read, +};/* * Default unassigned regions to raw read-write access. Some devices * require this to function as they hide registers between the gaps in
@@ -1582,7 +1586,7 @@ static int vfio_cap_init(struct vfio_pci_core_device *vdev) __func__, pos + i, map[pos + i], cap); } -BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );memset (map + pos, cap, len); ret =vfio_fill_vconfig_bytes (vdev, pos, len);
@@ -1673,9 +1677,9 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)/* * Even though ecap is 2 bytes, we're currently a long way * from exceeding 1 byte capabilities. If we ever make it -* up to 0xFE we'll need to up this to a two-byte, byte map. +* up to 0xFD we'll need to up this to a two-byte, byte map. */ -BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );memset (map + epos, ecap, len); ret =vfio_fill_vconfig_bytes (vdev, epos, len);
@@ -1688,10 +1692,11 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)* indicates to use cap id = 0, version = 0, next = 0 if * ecaps are absent, hope users check all the way to next. */ -if (hidden) +if (hidden) { *(__le32 *)&vdev->vconfig[epos] &=cpu_to_le32 ((0xffcU <<20 )); -else +memset (map + epos,PCI_CAP_ID_FIRST_HIDDEN , len); + }else ecaps++; prev = (__le32 *)&vdev->vconfig[epos];
@@ -1895,6 +1900,9 @@ static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user }else if (cap_id ==PCI_CAP_ID_INVALID_VIRT ) { perm = &virt_perms; cap_start = *ppos; + }else if (cap_id ==PCI_CAP_ID_FIRST_HIDDEN ) { + perm = &hidden_ecap_perm; + cap_start =PCI_CFG_SPACE_SIZE ; }else {if (*ppos >=PCI_CFG_SPACE_SIZE ) {WARN_ON (cap_id >PCI_EXT_CAP_ID_MAX );
Signature · 1 line
2.40.1
Quoted 66 lines · On Wed, 20 Nov 2024 16:38:26 +0200 Avihai Horon <[email protected]> wrote:
There are cases where a PCIe extended capability should be hidden from the user. For example, an unknown capability (i.e., capability with ID greater than
PCI_EXT_CAP_ID_MAX) or a capability that is intentionally chosen to be hidden from the user.Hiding a capability is done by virtualizing and modifying the 'Next Capability Offset' field of the previous capability so it points to the capability after the one that should be hidden.
The special case where the first capability in the list should be hidden is handled differently because there is no previous capability that can be modified. In this case, the capability ID and version are zeroed while leaving the next pointer intact. This hides the capability and leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done properly, as struct
vfio_pci_core_device->pci_config_mapis still set to the capability ID. If the first capability in the list is unknown, the following warning [1] is triggered and an out-of-bounds access toecap_permsarray occurs whenvfio_config_do_rw()later usespci_config_mapto pick the right permissions.Fix it by defining a new special capability
PCI_CAP_ID_FIRST_HIDDEN, that represents a hidden extended capability that is located first in the extended capability list, and setpci_config_mapto it in the above case.[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1 (snip) Call Trace: <TASK> ? show_regs+0x69/0x80 ? __warn+0x8d/0x140 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? report_bug+0x18f/0x1a0 ? handle_bug+0x63/0xa0 ? exc_invalid_op+0x19/0x70 ? asm_exc_invalid_op+0x1b/0x20 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core] vfio_pci_rw+0x101/0x1b0 [vfio_pci_core] vfio_pci_core_read+0x1d/0x30 [vfio_pci_core] vfio_device_fops_read+0x27/0x40 [vfio] vfs_read+0xbd/0x340 ? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio] ? __rseq_handle_notify_resume+0xa4/0x4b0 __x64_sys_pread64+0x96/0xc0 x64_sys_call+0x1c3d/0x20d0 do_syscall_64+0x4d/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7eFixes 89e1f7d4c66d ("vfio: Add PCI device driver")Signed-off-by Avihai Horon <[email protected]>--- drivers/vfio/pci/vfio_pci_priv.h | 1 + drivers/vfio/pci/vfio_pci_config.c | 18 +++++++++++++----- 2 files changed, 14 insertions(+), 5 deletions(-)drivers/vfio/pci/vfio_pci_priv.h +0
-0
drivers/vfio/pci/vfio_pci_priv.h line 10
Quoted 4 lines
drivers/vfio/pci/vfio_pci_priv.h +1
-0@@ -7,6 +7,7 @@/* Special capability IDs predefined access */ #define PCI_CAP_ID_INVALID 0xFF/* default raw access */ #define PCI_CAP_ID_INVALID_VIRT 0xFE/* default virt access */ +#define PCI_CAP_ID_FIRST_HIDDEN 0xFD/* default direct access */
Thanks for catching this! I wonder if the explicit tracking of this via another dummy capability ID is really necessary though. I think the only way we can get a value in the pci_config_map greater than PCI_EXT_CAP_ID_MAX is this scenario where it appears at the base of the extended capability chain. Therefore couldn't we just do something like (compile tested only):
drivers/vfio/pci/vfio_pci_config.c +16 -4
@@ -313,12 +313,16 @@ static int vfio_virt_config_read(struct vfio_pci_core_device *vdev, int pos,return count; } +static const struct perm_bits direct_ro_perms = { + .readfn = vfio_direct_config_read +}; +/* Default capability regions to read-only, no-virtualization */ static struct perm_bits cap_perms[PCI_CAP_ID_MAX +1 ] = { - [0 ...PCI_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } + [0 ...PCI_CAP_ID_MAX ] = direct_ro_perms };static struct perm_bits ecap_perms[PCI_EXT_CAP_ID_MAX +1 ] = { - [0 ...PCI_EXT_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } + [0 ...PCI_EXT_CAP_ID_MAX ] = direct_ro_perms };/* * Default unassigned regions to raw read-write access. Some devices
@@ -1897,9 +1901,17 @@ static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user cap_start = *ppos; }else {if (*ppos >=PCI_CFG_SPACE_SIZE ) { -WARN_ON (cap_id >PCI_EXT_CAP_ID_MAX ); +/* +* We can get a cap_id that exceeds PCI_EXT_CAP_ID_MAX +* if we're hiding an unknown capability at the start +* of the extended capability chain. Use default, ro +* access, which will virtualize the id and next values. +*/ +if (cap_id >PCI_EXT_CAP_ID_MAX ) + perm = (struct perm_bits *)&direct_ro_perms; +else + perm = &ecap_perms[cap_id]; - perm = &ecap_perms[cap_id]; cap_start =vfio_find_cap_start (vdev, *ppos); }else {WARN_ON (cap_id >PCI_CAP_ID_MAX );
Quoted 41 lines
drivers/vfio/pci/vfio_pci_priv.h +0
-0/* Cap maximum number of ioeventfds per device (arbitrary) */ #define VFIO_PCI_IOEVENTFD_MAX 1000drivers/vfio/pci/vfio_pci_config.c +7
-3@@ -320,6 +320,10 @@ static struct perm_bits cap_perms[PCI_CAP_ID_MAX + 1] = {static struct perm_bits ecap_perms[PCI_EXT_CAP_ID_MAX +1 ] = { [0 ...PCI_EXT_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } }; +/* Perms for a first-in-list hidden extended capability */ +static struct perm_bits hidden_ecap_perm = { + .readfn = vfio_direct_config_read, +};/* * Default unassigned regions to raw read-write access. Some devices * require this to function as they hide registers between the gaps in @@ -1582,7 +1586,7 @@ static int vfio_cap_init(struct vfio_pci_core_device *vdev) __func__, pos + i, map[pos + i], cap); } -BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );memset (map + pos, cap, len); ret =vfio_fill_vconfig_bytes (vdev, pos, len);@@ -1673,9 +1677,9 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)/* * Even though ecap is 2 bytes, we're currently a long way * from exceeding 1 byte capabilities. If we ever make it -* up to 0xFE we'll need to up this to a two-byte, byte map. +* up to 0xFD we'll need to up this to a two-byte, byte map. */ -BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );memset (map + epos, ecap, len); ret =vfio_fill_vconfig_bytes (vdev, epos, len);@@ -1688,10 +1692,11 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)* indicates to use cap id = 0, version = 0, next = 0 if
drivers/vfio/pci/vfio_pci_config.c static int vfio_ecap_init(struct vfio_pci_core_device *vdev) · line 1700
Quoted 10 lines
drivers/vfio/pci/vfio_pci_config.c +3
-2* ecaps are absent, hope users check all the way to next. */ -if (hidden) +if (hidden) { *(__le32 *)&vdev->vconfig[epos] &=cpu_to_le32 ((0xffcU <<20 )); -else +memset (map + epos,PCI_CAP_ID_FIRST_HIDDEN , len); + }else ecaps++;
We need to add braces on the else branch as well, per our coding style standard. Alternatively we might overwrite the ecap value where we previously set hidden to true. Thanks,
Alex
Quoted 12 lines
drivers/vfio/pci/vfio_pci_config.c +3
-0prev = (__le32 *)&vdev->vconfig[epos];@@ -1895,6 +1900,9 @@ static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user }else if (cap_id ==PCI_CAP_ID_INVALID_VIRT ) { perm = &virt_perms; cap_start = *ppos; + }else if (cap_id ==PCI_CAP_ID_FIRST_HIDDEN ) { + perm = &hidden_ecap_perm; + cap_start =PCI_CFG_SPACE_SIZE ; }else {if (*ppos >=PCI_CFG_SPACE_SIZE ) {WARN_ON (cap_id >PCI_EXT_CAP_ID_MAX );
Quoted 116 lines · Alex Williamson
External email: Use caution opening links or attachments
Quoted 66 lines · On Wed, 20 Nov 2024 16:38:26 +0200 Avihai Horon <[email protected]> wrote:
There are cases where a PCIe extended capability should be hidden from the user. For example, an unknown capability (i.e., capability with ID greater than
PCI_EXT_CAP_ID_MAX) or a capability that is intentionally chosen to be hidden from the user.Hiding a capability is done by virtualizing and modifying the 'Next Capability Offset' field of the previous capability so it points to the capability after the one that should be hidden.
The special case where the first capability in the list should be hidden is handled differently because there is no previous capability that can be modified. In this case, the capability ID and version are zeroed while leaving the next pointer intact. This hides the capability and leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done properly, as struct
vfio_pci_core_device->pci_config_mapis still set to the capability ID. If the first capability in the list is unknown, the following warning [1] is triggered and an out-of-bounds access toecap_permsarray occurs whenvfio_config_do_rw()later usespci_config_mapto pick the right permissions.Fix it by defining a new special capability
PCI_CAP_ID_FIRST_HIDDEN, that represents a hidden extended capability that is located first in the extended capability list, and setpci_config_mapto it in the above case.[1]
WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1 (snip) Call Trace: <TASK> ? show_regs+0x69/0x80 ? __warn+0x8d/0x140 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? report_bug+0x18f/0x1a0 ? handle_bug+0x63/0xa0 ? exc_invalid_op+0x19/0x70 ? asm_exc_invalid_op+0x1b/0x20 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core] vfio_pci_rw+0x101/0x1b0 [vfio_pci_core] vfio_pci_core_read+0x1d/0x30 [vfio_pci_core] vfio_device_fops_read+0x27/0x40 [vfio] vfs_read+0xbd/0x340 ? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio] ? __rseq_handle_notify_resume+0xa4/0x4b0 __x64_sys_pread64+0x96/0xc0 x64_sys_call+0x1c3d/0x20d0 do_syscall_64+0x4d/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7eFixes 89e1f7d4c66d ("vfio: Add PCI device driver")Signed-off-by Avihai Horon <[email protected]>--- drivers/vfio/pci/vfio_pci_priv.h | 1 + drivers/vfio/pci/vfio_pci_config.c | 18 +++++++++++++----- 2 files changed, 14 insertions(+), 5 deletions(-)drivers/vfio/pci/vfio_pci_priv.h +0
-0drivers/vfio/pci/vfio_pci_priv.h line 10
Quoted 4 lines
drivers/vfio/pci/vfio_pci_priv.h +1
-0@@ -7,6 +7,7 @@/* Special capability IDs predefined access */ #define PCI_CAP_ID_INVALID 0xFF/* default raw access */ #define PCI_CAP_ID_INVALID_VIRT 0xFE/* default virt access */ +#define PCI_CAP_ID_FIRST_HIDDEN 0xFD/* default direct access */ Thanks for catching this! I wonder if the explicit tracking of this via another dummy capability ID is really necessary though. I think the only way we can get a value in the
pci_config_mapgreater thanPCI_EXT_CAP_ID_MAXis this scenario where it appears at the base of the extended capability chain. Therefore couldn't we just do something like (compile tested only):drivers/vfio/pci/vfio_pci_config.c +11
-3@@ -313,12 +313,16 @@ static int vfio_virt_config_read(struct vfio_pci_core_device *vdev, int pos,return count; } +static const struct perm_bits direct_ro_perms = { + .readfn = vfio_direct_config_read +}; +/* Default capability regions to read-only, no-virtualization */ static struct perm_bits cap_perms[PCI_CAP_ID_MAX +1 ] = { - [0 ...PCI_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } + [0 ...PCI_CAP_ID_MAX ] = direct_ro_perms };static struct perm_bits ecap_perms[PCI_EXT_CAP_ID_MAX +1 ] = { - [0 ...PCI_EXT_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } + [0 ...PCI_EXT_CAP_ID_MAX ] = direct_ro_perms };/* * Default unassigned regions to raw read-write access. Some devices @@ -1897,9 +1901,17 @@ static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user cap_start = *ppos; }else {if (*ppos >=PCI_CFG_SPACE_SIZE ) { -WARN_ON (cap_id >PCI_EXT_CAP_ID_MAX ); +/* +* We can get a cap_id that exceeds PCI_EXT_CAP_ID_MAX +* if we're hiding an unknown capability at the start +* of the extended capability chain. Use default, ro +* access, which will virtualize the id and next values.
drivers/vfio/pci/vfio_pci_config.c static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user · line 1917
Quoted 10 lines
drivers/vfio/pci/vfio_pci_config.c +5
-1+*/ +if (cap_id >PCI_EXT_CAP_ID_MAX ) + perm = (struct perm_bits *)&direct_ro_perms; +else + perm = &ecap_perms[cap_id]; - perm = &ecap_perms[cap_id]; cap_start =vfio_find_cap_start (vdev, *ppos); }else {WARN_ON (cap_id >PCI_CAP_ID_MAX );
Yes, you are right. This works and appears to be simpler than my fix. I will send a v2 with your suggestion shortly.
Quoted 37 lines
Quoted 37 lines
drivers/vfio/pci/vfio_pci_priv.h +0
-0/* Cap maximum number of ioeventfds per device (arbitrary) */ #define VFIO_PCI_IOEVENTFD_MAX 1000drivers/vfio/pci/vfio_pci_config.c +7
-3@@ -320,6 +320,10 @@ static struct perm_bits cap_perms[PCI_CAP_ID_MAX + 1] = {static struct perm_bits ecap_perms[PCI_EXT_CAP_ID_MAX +1 ] = { [0 ...PCI_EXT_CAP_ID_MAX ] = { .readfn = vfio_direct_config_read } }; +/* Perms for a first-in-list hidden extended capability */ +static struct perm_bits hidden_ecap_perm = { + .readfn = vfio_direct_config_read, +};/* * Default unassigned regions to raw read-write access. Some devices * require this to function as they hide registers between the gaps in @@ -1582,7 +1586,7 @@ static int vfio_cap_init(struct vfio_pci_core_device *vdev) __func__, pos + i, map[pos + i], cap); } -BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );memset (map + pos, cap, len); ret =vfio_fill_vconfig_bytes (vdev, pos, len);@@ -1673,9 +1677,9 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)/* * Even though ecap is 2 bytes, we're currently a long way * from exceeding 1 byte capabilities. If we ever make it -* up to 0xFE we'll need to up this to a two-byte, byte map. +* up to 0xFD we'll need to up this to a two-byte, byte map. */ -BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_INVALID_VIRT ); +BUILD_BUG_ON (PCI_EXT_CAP_ID_MAX >=PCI_CAP_ID_FIRST_HIDDEN );
Quoted 16 lines
Quoted 4 lines
drivers/vfio/pci/vfio_pci_config.c +0
-0memset (map + epos, ecap, len); ret =vfio_fill_vconfig_bytes (vdev, epos, len);@@ -1688,10 +1692,11 @@ static int vfio_ecap_init(struct vfio_pci_core_device *vdev)* indicates to use cap id = 0, version = 0, next = 0 if drivers/vfio/pci/vfio_pci_config.c static int vfio_ecap_init(struct vfio_pci_core_device *vdev) · line 1700
Quoted 10 lines
drivers/vfio/pci/vfio_pci_config.c +3
-2* ecaps are absent, hope users check all the way to next. */ -if (hidden) +if (hidden) { *(__le32 *)&vdev->vconfig[epos] &=cpu_to_le32 ((0xffcU <<20 )); -else +memset (map + epos,PCI_CAP_ID_FIRST_HIDDEN , len); + }else ecaps++;We need to add braces on the else branch as well, per our coding style standard.
Ack, I will remember this for future work.
Thanks!
Quoted 16 lines
Alternatively we might overwrite the ecap value where we previously set hidden to true. Thanks,
Alex
Quoted 11 lines
drivers/vfio/pci/vfio_pci_config.c +3
-0prev = (__le32 *)&vdev->vconfig[epos];@@ -1895,6 +1900,9 @@ static ssize_t vfio_config_do_rw(struct vfio_pci_core_device *vdev, char __user }else if (cap_id ==PCI_CAP_ID_INVALID_VIRT ) { perm = &virt_perms; cap_start = *ppos; + }else if (cap_id ==PCI_CAP_ID_FIRST_HIDDEN ) { + perm = &hidden_ecap_perm; + cap_start =PCI_CFG_SPACE_SIZE ; }else {if (*ppos >=PCI_CFG_SPACE_SIZE ) {WARN_ON (cap_id >PCI_EXT_CAP_ID_MAX );