Skip to contentSkip to conversation

mci: sdhci: arasan: use correct input clock for divider calculation

PATCH Applied Lucas Stach 2 participants 3 messages Dec 12, 2024 – Dec 16, 2024

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 mci: sdhci: arasan: use correct input clock for divider calculation

Use the clock rate going into the core to calculate the divider. Fixes broken SD card transfers on Zynq 7000.

Fixes 2a879e436a5f ("mci: sdhci: arasan: Use sdhci_set_clock()")
---
 drivers/mci/arasan-sdhci.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mci/arasan-sdhci.c +1 -1
index 37be06dffdfe..2af9ad10bed7 100644
@@ -210,7 +210,7 @@ static void arasan_sdhci_set_clock(struct mci_host *mci, unsigned int clock)
 	clk_set_phase(clk_data->sdcardclk,
 		      clk_data->clk_phase_out[mci->mci->host->timing]);
 
-	sdhci_set_clock(&host->sdhci, clock, host->sdhci.max_clk);
+	sdhci_set_clock(&host->sdhci, clock, mci->f_max);
 }
 
 static void arasan_sdhci_set_ios(struct mci_host *mci, struct mci_ios *ios)
Signature · 1 line
2.47.1
#1 lore raw

PATCH 2/2 mci: sdhci: arasan: remove dead no 1.8V quirk

Since 21e5f283cb72 ("mci: sdhci: arasan: Use sdhci_setup_host()"), the no-1-8-v DT property is handled by the common mci_of_parse. Remove the dead quirk from the driver.

---
 drivers/mci/arasan-sdhci.c | 4 ----
 1 file changed, 4 deletions(-)
drivers/mci/arasan-sdhci.c +0 -4
index 2af9ad10bed7..112fb5a669d5 100644
@@ -70,7 +70,6 @@ struct arasan_sdhci_host {
 	struct sdhci_arasan_clk_data clk_data;
 /* Controller does not have CD wired and will not function normally without */
 #define SDHCI_ARASAN_QUIRK_FORCE_CDTEST		BIT(0)
-#define SDHCI_ARASAN_QUIRK_NO_1_8_V		BIT(1)
 /*
  * Some of the Arasan variations might not have timing requirements
  * met at 25MHz for Default Speed mode, those controllers work at
@@ -768,9 +767,6 @@ static int arasan_sdhci_probe(struct device *dev)
 	if (of_property_read_bool(np, "xlnx,fails-without-test-cd"))
 		arasan_sdhci->quirks |= SDHCI_ARASAN_QUIRK_FORCE_CDTEST;
 
-	if (of_property_read_bool(np, "no-1-8-v"))
-		arasan_sdhci->quirks |= SDHCI_ARASAN_QUIRK_NO_1_8_V;
-
 	if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a")) {
 		if (IS_ENABLED(CONFIG_MCI_TUNING))
 			mci->ops.execute_tuning = arasan_zynqmp_execute_tuning;
Signature · 1 line
2.47.1
Applied
#2 lore raw
In reply to Lucas Stach
Quoted 4 lines · Lucas Stach

Use the clock rate going into the core to calculate the divider. Fixes broken SD card transfers on Zynq 7000.

Applied, thanks!

[1/2] mci: sdhci: arasan: use correct input clock for divider calculation
https://git.pengutronix.de/cgit/barebox/commit/?id=b6225b579bbd (link may not be stable)
[2/2] mci: sdhci: arasan: remove dead no 1.8V quirk
https://git.pengutronix.de/cgit/barebox/commit/?id=72939ae3594d (link may not be stable)

Best regards,

Signature · 1 line
Sascha Hauer <[email protected]>