Skip to contentSkip to conversation

{am62,am62a}-phycore-som: Add R5F and C7xv device nodes

PATCH Superseded Daniel Schultz 4 participants 8 messages May 6, 2025

Subsystems (2)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover {am62,am62a}-phycore-som: Add R5F and C7xv device nodes

This patch series is based on [1] and adds these R5F and C7xv device nodes to the am62- and am62a-phycore-som device-trees. It also reserves main_timer2 as well as main_rti4 for the C7 DSP firmware.

1: https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#t

Daniel Schultz (4):
arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors
arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors
arm64: dts: ti: k3-am62a-phycore-som: Reserve main_rti4 for C7x DSP
arm64: dts: ti: k3-am62a-phycore-som: Reserve main_timer2 for C7x DSP

 .../boot/dts/ti/k3-am62-phycore-som.dtsi      |  35 +++++-
 .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 106 +++++++++++++++++-
 2 files changed, 129 insertions(+), 12 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/4 arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors

For every remote processor, set up dedicated memory regions and associate the required mailbox channels. Allocate two memory areas per remote core: one 1MB region for vring shared buffers, and another for external memory used by the remote processor for its resource table and trace buffer.

---
 .../boot/dts/ti/k3-am62-phycore-som.dtsi      | 35 +++++++++++++++----
 1 file changed, 29 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi +29 -6
index 2ef4cbaec789..71d165a7abe0 100644
@@ -57,6 +57,18 @@ mcu_m4fss_memory_region: m4f-memory@9cc00000 {
 			no-map;
 		};
 
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9da00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9da00000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+
 		secure_tfa_ddr: tfa@9e780000 {
 			reg = <0x00 0x9e780000 0x00 0x80000>;
 			alignment = <0x1000>;
@@ -68,12 +80,6 @@ secure_ddr: optee@9e800000 {
 			alignment = <0x1000>;
 			no-map;
 		};
-
-		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9db00000 0x00 0x00c00000>;
-			no-map;
-		};
 	};
 
 	vcc_5v0_som: regulator-vcc-5v0-som {
@@ -226,10 +232,17 @@ cpsw3g_phy1: ethernet-phy@1 {
 };
 
 &mailbox0_cluster0 {
+	status = "okay";
+
 	mbox_m4_0: mbox-m4-0 {
 		ti,mbox-rx = <0 0 0>;
 		ti,mbox-tx = <1 0 0>;
 	};
+
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
 };
 
 &main_i2c0 {
@@ -365,3 +378,13 @@ &sdhci0 {
 	non-removable;
 	status = "okay";
 };
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+			<&wkup_r5fss0_core0_memory_region>;
+};
Signature · 1 line
2.25.1
Reviewed-by on v1 1/4
#2 lore raw

Re: [PATCH 1/4] arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors

Quoted 8 lines · Daniel Schultz

For every remote processor, set up dedicated memory regions and associate the required mailbox channels. Allocate two memory areas per remote core: one 1MB region for vring shared buffers, and another for external memory used by the remote processor for its resource table and trace buffer.

---

Quoted 71 lines
  .../boot/dts/ti/k3-am62-phycore-som.dtsi      | 35 +++++++++++++++----
  1 file changed, 29 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi +29 -6
index 2ef4cbaec789..71d165a7abe0 100644
@@ -57,6 +57,18 @@ mcu_m4fss_memory_region: m4f-memory@9cc00000 {
  			no-map;
  		};
 
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9da00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9da00000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+
  		secure_tfa_ddr: tfa@9e780000 {
  			reg = <0x00 0x9e780000 0x00 0x80000>;
  			alignment = <0x1000>;
@@ -68,12 +80,6 @@ secure_ddr: optee@9e800000 {
  			alignment = <0x1000>;
  			no-map;
  		};
-
-		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9db00000 0x00 0x00c00000>;
-			no-map;
-		};
  	};
 
  	vcc_5v0_som: regulator-vcc-5v0-som {
@@ -226,10 +232,17 @@ cpsw3g_phy1: ethernet-phy@1 {
  };
 
  &mailbox0_cluster0 {
+	status = "okay";
+
  	mbox_m4_0: mbox-m4-0 {
  		ti,mbox-rx = <0 0 0>;
  		ti,mbox-tx = <1 0 0>;
  	};
+
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
  };
 
  &main_i2c0 {
@@ -365,3 +378,13 @@ &sdhci0 {
  	non-removable;
  	status = "okay";
  };
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+			<&wkup_r5fss0_core0_memory_region>;
+};
#3 lore raw

PATCH 2/4 arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

In reply to Daniel Schultz

For every remote processor, set up dedicated memory regions and associate the required mailbox channels. Allocate two memory areas per remote core: one 1MB region for vring shared buffers, and another for external memory used by the remote processor for its resource table and trace buffer.

---
 .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
 1 file changed, 90 insertions(+), 6 deletions(-)
arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi +90 -6
index a5aceaa39670..fc252543f18a 100644
@@ -58,6 +58,42 @@ linux,cma {
 			linux,cma-default;
 		};
 
+		c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99800000 0x00 0x100000>;
+			no-map;
+		};
+
+		c7x_0_memory_region: c7x-memory@99900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b800000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c800000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c900000 0x00 0xf00000>;
+			no-map;
+		};
+
 		secure_tfa_ddr: tfa@9e780000 {
 			reg = <0x00 0x9e780000 0x00 0x80000>;
 			alignment = <0x1000>;
@@ -69,12 +105,6 @@ secure_ddr: optee@9e800000 {
 			alignment = <0x1000>;
 			no-map;
 		};
-
-		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9c900000 0x00 0x01e00000>;
-			no-map;
-		};
 	};
 
 	vcc_5v0_som: regulator-vcc-5v0-som {
@@ -164,6 +194,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) EXTINTn */
 	};
 };
 
+&c7x_0 {
+	mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
+	memory-region = <&c7x_0_dma_memory_region>,
+			<&c7x_0_memory_region>;
+	status = "okay";
+};
+
 &cpsw3g {
 	status = "okay";
 	pinctrl-names = "default";
@@ -192,6 +229,33 @@ &fss {
 	status = "okay";
 };
 
+&mailbox0_cluster0 {
+	status = "okay";
+
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster1 {
+	status = "okay";
+
+	mbox_c7x_0: mbox-c7x-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster2 {
+	status = "okay";
+
+	mbox_mcu_r5_0: mbox-mcu-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
 &main_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_pins_default>;
@@ -302,6 +366,16 @@ &main_gpio_intr {
 	status = "okay";
 };
 
+&mcu_r5fss0 {
+	status = "okay";
+};
+
+&mcu_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+};
+
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
@@ -328,3 +402,13 @@ &sdhci0 {
 	non-removable;
 	status = "okay";
 };
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+			<&wkup_r5fss0_core0_memory_region>;
+};
Signature · 1 line
2.25.1
#4 lore raw

PATCH 3/4 arm64: dts: ti: k3-am62a-phycore-som: Reserve main_rti4 for C7x DSP

In reply to Daniel Schultz

The main rti4 watchdog timer is used by the C7x DSP, so reserve the timer in the linux device tree.

---
 arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi | 5 +++++
 1 file changed, 5 insertions(+)
arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi +5 -0
index fc252543f18a..343118af448b 100644
@@ -366,6 +366,11 @@ &main_gpio_intr {
 	status = "okay";
 };
 
+/* main_rti4 is used by C7x DSP */
+&main_rti4 {
+	status = "reserved";
+};
+
 &mcu_r5fss0 {
 	status = "okay";
 };
Signature · 1 line
2.25.1
#5 lore raw

PATCH 4/4 arm64: dts: ti: k3-am62a-phycore-som: Reserve main_timer2 for C7x DSP

In reply to Daniel Schultz

C7x DSP uses main_timer2, so mark it as reserved in linux DT.

---
 arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi | 5 +++++
 1 file changed, 5 insertions(+)
arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi +5 -0
index 343118af448b..b6c46c410b78 100644
@@ -371,6 +371,11 @@ &main_rti4 {
 	status = "reserved";
 };
 
+/* main_timer2 is used by C7x DSP */
+&main_timer2 {
+	status = "reserved";
+};
+
 &mcu_r5fss0 {
 	status = "okay";
 };
Signature · 1 line
2.25.1
#6 lore raw
In reply to Daniel Schultz

Am 06.05.25 um 14:54 schrieb Daniel Schultz:

Quoted 11 lines

This patch series is based on [1] and adds these R5F and C7xv device nodes to the am62- and am62a-phycore-som device-trees. It also reserves main_timer2 as well as main_rti4 for the C7 DSP firmware.

1: https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#t

Daniel Schultz (4):
arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors
arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors
arm64: dts: ti: k3-am62a-phycore-som: Reserve main_rti4 for C7x DSP
arm64: dts: ti: k3-am62a-phycore-som: Reserve main_timer2 for C7x DSP

Patches do not apply on master

Quoted 5 lines
  .../boot/dts/ti/k3-am62-phycore-som.dtsi      |  35 +++++-
  .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 106 +++++++++++++++++-
  2 files changed, 129 insertions(+), 12 deletions(-)