sunxi: A64: enable AXP driver support
Subsystems (3)
cover sunxi: A64: enable AXP driver support
Hi,
this series enables the build of the AXP driver in U-Boot proper for all boards using the Allwinner A64 SoC. So far some static PMIC rail setup was done by TF-A, but this was rather static (enabling too many) and increases the code size of the rather limited BL31 build.
Do this for the A64 only first, since this uses RSB consistently, while the H6 boards are undergoing a transition to use I2C.
Please have a look and test!
Cheers,
Andre
Andre Przywara (2):
sunxi: A64: enable DRIVEVBUS support for respective boards
sunxi: A64: enable AXP drivers
arch/arm/Kconfig | 1 + arch/arm/mach-sunxi/Kconfig | 3 +++ configs/a64-olinuxino-emmc_defconfig | 1 + configs/a64-olinuxino_defconfig | 1 + configs/amarula_a64_relic_defconfig | 1 + configs/bananapi_m64_defconfig | 1 + configs/orangepi_win_defconfig | 1 + configs/pinetab_defconfig | 1 + 8 files changed, 10 insertions(+)
Signature · 1 line
2.46.3
PATCH 1/2 sunxi: A64: enable DRIVEVBUS support for respective boards
The X-Powers AXP PMICs contain a special pin that can be used to drive USB VBUS power, which requires a special AXP (sub-)driver.
Enable that for the 64-bit boards that use this pin, so that they can enable VBUS power on their own, without relying on the help of TF-A.
--- configs/a64-olinuxino-emmc_defconfig | 1 + configs/a64-olinuxino_defconfig | 1 + configs/amarula_a64_relic_defconfig | 1 + configs/bananapi_m64_defconfig | 1 + configs/orangepi_win_defconfig | 1 + configs/pinetab_defconfig | 1 + 6 files changed, 6 insertions(+)
configs/a64-olinuxino-emmc_defconfig +1 -0
@@ -7,5 +7,6 @@ CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_SUN8I_EMAC=y +CONFIG_REGULATOR_AXP_DRIVEVBUS=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y
configs/a64-olinuxino_defconfig +1 -0
@@ -6,5 +6,6 @@ CONFIG_MACH_SUN50I=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUN8I_EMAC=y +CONFIG_REGULATOR_AXP_DRIVEVBUS=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y
configs/amarula_a64_relic_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_MACH_SUN50I=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_VIDEO_DE2 is not set # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_REGULATOR_AXP_DRIVEVBUS=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_MUSB_GADGET=y
configs/bananapi_m64_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_SUN8I_EMAC=y +CONFIG_REGULATOR_AXP_DRIVEVBUS=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_MUSB_GADGET=y
configs/orangepi_win_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_MTD=y CONFIG_SPI_FLASH_WINBOND=y CONFIG_PHY_REALTEK=y CONFIG_SUN8I_EMAC=y +CONFIG_REGULATOR_AXP_DRIVEVBUS=y CONFIG_SPI=y CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y
configs/pinetab_defconfig +1 -0
@@ -8,3 +8,4 @@ CONFIG_DRAM_CLK=552 CONFIG_DRAM_ZQ=3881949 CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_REGULATOR_AXP_DRIVEVBUS=y
Signature · 1 line
2.46.3
PATCH 2/2 sunxi: A64: enable AXP drivers
In reply to Andre PrzywaraSo far the 64-bit SoCs were relying on Trusted-Firmware to do the PMIC setup, which was quite static: enabling most rails, regardless of whether they are needed or not.
We have a fully DM compliant AXP regulator driver for a while, so that U-Boot proper can do its own PMIC setup, based on the actual need (typically for USB, Ethernet, HDMI).
Enable that driver by default for all A64 boards, along with the RSB driver.
The goal is to allow dropping the ill-fated regulator setup code from TF-A, so that this can become smaller, and we only enable rails that are really needed.
--- arch/arm/Kconfig | 1 + arch/arm/mach-sunxi/Kconfig | 3 +++ 2 files changed, 4 insertions(+)
arch/arm/Kconfig +1 -0
@@ -1190,6 +1190,7 @@ config ARCH_SUNXI select DM_SPI_FLASH if SPI && MTD select DM_KEYBOARD select DM_SERIAL + select DM_PMIC select MMU_PGPROT if ARM64 select OF_BOARD_SETUP select OF_CONTROL
arch/arm/mach-sunxi/Kconfig +3 -0
@@ -435,6 +435,9 @@ config MACH_SUN50I select FIT select SPL_LOAD_FIT if SPL select SUNXI_A64_TIMER_ERRATUM + imply SYS_I2C_SUN8I_RSB + imply REGULATOR_AXP + imply PMIC_AXP config MACH_SUN50I_H5 bool "sun50i (Allwinner H5)"
Signature · 1 line
2.46.3
Jernej Škrabec
maintainerDne sreda, 7. maj 2025 ob 02:53:23 Srednjeevropski poletni čas je Andre Przywara napisal(a):
Quoted 9 lines
Hi,
this series enables the build of the AXP driver in U-Boot proper for all boards using the Allwinner A64 SoC. So far some static PMIC rail setup was done by TF-A, but this was rather static (enabling too many) and increases the code size of the rather limited BL31 build.
Do this for the A64 only first, since this uses RSB consistently, while the H6 boards are undergoing a transition to use I2C.
What is status of this? Unfortunatelly I don't have time to test currently, but it would be nice to have this in.
Best regards,
Jernej
Quoted 21 lines
Please have a look and test!
Cheers,
AndreAndre Przywara (2):
sunxi: A64: enable DRIVEVBUS support for respective boards
sunxi: A64: enable AXP driversarch/arm/Kconfig | 1 + arch/arm/mach-sunxi/Kconfig | 3 +++ configs/a64-olinuxino-emmc_defconfig | 1 + configs/a64-olinuxino_defconfig | 1 + configs/amarula_a64_relic_defconfig | 1 + configs/bananapi_m64_defconfig | 1 + configs/orangepi_win_defconfig | 1 + configs/pinetab_defconfig | 1 + 8 files changed, 10 insertions(+)
Quoted 8 lines · Andre Przywara
Hi,
this series enables the build of the AXP driver in U-Boot proper for all boards using the Allwinner A64 SoC. So far some static PMIC rail setup was done by TF-A, but this was rather static (enabling too many) and increases the code size of the rather limited BL31 build.
Quoted 4 lines
Do this for the A64 only first, since this uses RSB consistently, while the H6 boards are undergoing a transition to use I2C.
Please have a look and test!
For the series:
Tested on a Pine64+, I enabled CMD_PMIC and CMD_REGULATOR and could see all the expected details as well as in the output in 'dm tree' and it boots and runs as expected with Fedora 43.
Peter
Quoted 20 lines
Cheers,
AndreAndre Przywara (2):
sunxi: A64: enable DRIVEVBUS support for respective boards
sunxi: A64: enable AXP driversarch/arm/Kconfig | 1 + arch/arm/mach-sunxi/Kconfig | 3 +++ configs/a64-olinuxino-emmc_defconfig | 1 + configs/a64-olinuxino_defconfig | 1 + configs/amarula_a64_relic_defconfig | 1 + configs/bananapi_m64_defconfig | 1 + configs/orangepi_win_defconfig | 1 + configs/pinetab_defconfig | 1 + 8 files changed, 10 insertions(+)--
2.46.3