sc5xx: Add complete board support for all ADI SC5xx boards
Subsystems (2)
cover sc5xx: Add complete board support for all ADI SC5xx boards
This series adds the final pieces to enable mainline U-Boot to build and boot all Analog Devices SC5xx SoCs and supports the associated carrier board options. At this point it should be viable for new users for these platforms to start with the latest version of U-Boot rather than our vendor fork, however some features (such as OSPI support and falcon boot) remain unavailable until we are able to unify our implementations with the mainline implementations.
Greg Malysa (8):
docker: add ADI build-related tools to docker image
board: adi: Add SOMCRR infrastructure
board: adi: Add support for SC573-ezkit
board: adi: Add support for SC589 boards
board: adi: Add support for SC584
board: adi: Add support for SC598
board: adi: Add support for SC594
MAINTAINERS: Update ADI entries for new boards
Utsav Agarwal (2):
mach-sc5xx: Introduce Kconfig symbols for image addresses
mach-sc5xx: Add binman support
MAINTAINERS | 1 + arch/arm/dts/sc573-ezkit.dts | 227 +++++++++++++++++ arch/arm/dts/sc57x.dtsi | 123 ++++++++- arch/arm/dts/sc584-ezkit.dts | 230 +++++++++++++++++ arch/arm/dts/sc589-ezkit.dts | 198 +++++++++++++++ arch/arm/dts/sc589-mini.dts | 18 +- arch/arm/dts/sc58x.dtsi | 153 ++++++++++- arch/arm/dts/sc594-som-ezkit.dts | 126 ++++++++++ arch/arm/dts/sc594-som-ezlite.dts | 83 ++++++ arch/arm/dts/sc594-som.dtsi | 184 +++++++++++++- arch/arm/dts/sc598-som-ezkit.dts | 166 ++++++++++++ arch/arm/dts/sc598-som-ezlite.dts | 82 ++++++ arch/arm/dts/sc598-som.dtsi | 237 +++++++++++++++++- arch/arm/dts/sc59x.dtsi | 183 ++++++++++++++ arch/arm/dts/sc5xx.dtsi | 189 +++++++++++++- arch/arm/mach-sc5xx/Kconfig | 63 +++++ board/adi/carriers/Makefile | 8 + board/adi/carriers/somcrr.h | 14 ++ board/adi/carriers/somcrr_common.c | 19 ++ board/adi/carriers/somcrr_ezkit.c | 38 +++ board/adi/carriers/somcrr_ezlite.c | 24 ++ board/adi/common-sc594-som/sc594-som.c | 34 +++ board/adi/common-sc598-som/sc598-som.c | 34 +++ board/adi/sc573-ezkit/Makefile | 6 + board/adi/sc573-ezkit/sc573-ezkit.c | 21 ++ board/adi/sc573-ezkit/sc573-ezkit.env | 17 +- board/adi/sc584-ezkit/Makefile | 6 + board/adi/sc584-ezkit/sc584-ezkit.c | 21 ++ board/adi/sc584-ezkit/sc584-ezkit.env | 16 +- board/adi/sc589-ezkit/Makefile | 6 + board/adi/sc589-ezkit/sc589-ezkit.c | 21 ++ board/adi/sc589-ezkit/sc589-ezkit.env | 17 +- board/adi/sc589-mini/Makefile | 6 + board/adi/sc589-mini/sc589-mini.c | 21 ++ board/adi/sc589-mini/sc589-mini.env | 17 +- board/adi/sc594-som-ezkit/Makefile | 8 + board/adi/sc594-som-ezkit/sc594-som-ezkit.env | 18 +- board/adi/sc594-som-ezlite/Makefile | 8 + .../adi/sc594-som-ezlite/sc594-som-ezlite.env | 18 +- board/adi/sc598-som-ezkit/Makefile | 8 + board/adi/sc598-som-ezkit/sc598-som-ezkit.env | 18 +- board/adi/sc598-som-ezlite/Makefile | 8 + .../adi/sc598-som-ezlite/sc598-som-ezlite.env | 12 +- configs/sc573-ezkit_defconfig | 102 ++++++++ configs/sc584-ezkit_defconfig | 108 ++++++++ configs/sc589-ezkit_defconfig | 113 +++++++++ configs/sc589-mini_defconfig | 109 ++++++++ configs/sc594-som-ezkit-spl_defconfig | 90 +++++++ configs/sc594-som-ezlite-spl_defconfig | 98 ++++++++ configs/sc598-som-ezkit-spl_defconfig | 123 +++++++++ configs/sc598-som-ezlite-spl_defconfig | 123 +++++++++ tools/docker/Dockerfile | 8 + 52 files changed, 3508 insertions(+), 73 deletions(-) create mode 100644 arch/arm/dts/sc59x.dtsi create mode 100644 board/adi/carriers/Makefile create mode 100644 board/adi/carriers/somcrr.h create mode 100644 board/adi/carriers/somcrr_common.c create mode 100644 board/adi/carriers/somcrr_ezkit.c create mode 100644 board/adi/carriers/somcrr_ezlite.c create mode 100644 board/adi/common-sc594-som/sc594-som.c create mode 100644 board/adi/common-sc598-som/sc598-som.c create mode 100644 board/adi/sc573-ezkit/Makefile create mode 100644 board/adi/sc573-ezkit/sc573-ezkit.c create mode 100644 board/adi/sc584-ezkit/Makefile create mode 100644 board/adi/sc584-ezkit/sc584-ezkit.c create mode 100644 board/adi/sc589-ezkit/Makefile create mode 100644 board/adi/sc589-ezkit/sc589-ezkit.c create mode 100644 board/adi/sc589-mini/Makefile create mode 100644 board/adi/sc589-mini/sc589-mini.c create mode 100644 board/adi/sc594-som-ezkit/Makefile create mode 100644 board/adi/sc594-som-ezlite/Makefile create mode 100644 board/adi/sc598-som-ezkit/Makefile create mode 100644 board/adi/sc598-som-ezlite/Makefile create mode 100644 configs/sc573-ezkit_defconfig create mode 100644 configs/sc584-ezkit_defconfig create mode 100644 configs/sc589-ezkit_defconfig create mode 100644 configs/sc589-mini_defconfig create mode 100644 configs/sc594-som-ezkit-spl_defconfig create mode 100644 configs/sc594-som-ezlite-spl_defconfig create mode 100644 configs/sc598-som-ezkit-spl_defconfig create mode 100644 configs/sc598-som-ezlite-spl_defconfig
Signature · 4 lines
2.45.2 base-commit: 2f3766949bbea7aa5a472157561d387fd94205d2 branch: dev/sc5xx-boards-v1
PATCH 1/10 mach-sc5xx: Introduce Kconfig symbols for image addresses
From: Utsav Agarwal <[email protected]>
Add Kconfig symbols to parameterize the SPI flash layout used in a default-ish configuration. This adds more flexibility to the default ADI environment, enabling customers with boards based on but not identical to an ezkit to reuse more of the infrastructure. Furthermore it allows for yocto (the expected default) or binman (to be introduced in this series) to configure or use the flash layout based on a single definition of all of the parameters when creating an image.
---
--- arch/arm/mach-sc5xx/Kconfig | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+)
arch/arm/mach-sc5xx/Kconfig +30 -0
@@ -117,6 +117,36 @@ endchoice endif +config SC5XX_UBOOT_SPL_OFFSET + hex "SPL offset" + default 0x0 + help + The default offset where the SPL is located. + +config SC5XX_UBOOT_OFFSET + hex "U-Boot offset" + default 0x40000 + help + The default offset where u-boot is located. + +config SC5XX_FITIMAGE_OFFSET + hex "FitImage offset" + default 0x1a0000 + help + The default offset where the fitImage is located. + +config SC5XX_ROOTFS_OFFSET + hex "RootFS offset" + default 0x102000 + help + The default offset where the rootfs is located. + +config SC5XX_LOADADDR + hex "Load address" + default 0x90000000 + help + The default load address for u-boot. + config ADI_IMAGE string "ADI fitImage type" help
Signature · 1 line
2.45.2
PATCH 2/10 mach-sc5xx: Add binman support
In reply to Greg MalysaFrom: Utsav Agarwal <[email protected]>
Binman is optionally supported for Analog Devices sc5xx if Yocto is not being used to create and assemble system images. The spl LDR is generated locally but other artifacts such as kernel FIT image, stage 2 bootloader LDR, and root file system are built externally and must be supplied to binman if used.
Binman is enabled by selecting the SC5XX_USE_BINMAN config symbol and the image structure is included in the shared sc5xx device tree.
---
arch/arm/dts/sc5xx.dtsi | 52 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-sc5xx/Kconfig | 33 +++++++++++++++++++++++ 2 files changed, 85 insertions(+)
arch/arm/dts/sc5xx.dtsi +52 -0
@@ -10,6 +10,58 @@ #address-cells = <1>; #size-cells = <1>; + chosen { + stdout-path = "serial0:115200"; + bootph-pre-ram; + }; + + aliases { + spi2 = "/spi2"; + serial0 = &uart0; + bootph-pre-ram; + }; + +#ifdef CONFIG_SC5XX_USE_BINMAN + binman { + filename = CONFIG_SC5XX_BINMAN_FILENAME; + stage1-boot { + offset = <CONFIG_SC5XX_UBOOT_SPL_OFFSET>; + type = "blob-ext"; + filename = "spl/u-boot-spl.ldr"; + }; + + /* since falcon mode can jump from SPL to OS directly + * full u-boot is optional + * + * @todo: review if we can say this given support has + * not yet been upstreamed. Otherwise we might have to + * invoke binman only for full u-boot. + */ + stage2-boot { + offset = <CONFIG_SC5XX_UBOOT_OFFSET>; + type = "blob-ext"; + filename = "u-boot.ldr"; + optional; + }; + +#ifdef CONFIG_SC5XX_FITIMAGE_NAME + fitImage { + offset = <CONFIG_SC5XX_FITIMAGE_OFFSET>; + type = "blob-ext"; + filename = CONFIG_SC5XX_FITIMAGE_NAME; + }; +#endif + +#ifdef CONFIG_SC5XX_ROOTFS_NAME + rfs { + offset = <CONFIG_SC5XX_ROOTFS_OFFSET>; + type = "blob-ext"; + filename = CONFIG_SC5XX_ROOTFS_NAME; + }; +#endif + }; +#endif + clocks { sys_clkin0: sys_clkin0 { compatible = "fixed-clock";
arch/arm/mach-sc5xx/Kconfig +33 -0
@@ -147,6 +147,39 @@ config SC5XX_LOADADDR help The default load address for u-boot. +menu "Binman configuration" +config SC5XX_USE_BINMAN + bool "Use binman for final image" + select BINMAN + help + If you wish to use binman to assemble an image, say 'Y' here. + This will enable binman-specific sections in the device tree. + +config SC5XX_BINMAN_FILENAME + string "Image name" + default "sc5xx-image.img" + depends on SC5XX_USE_BINMAN + help + The name of the image that will be created by binman. + This is used to create the final image. + +config SC5XX_FITIMAGE_NAME + string "FitImage name" + default "fitImage" + depends on SC5XX_USE_BINMAN + help + The name of the fitImage to be packed by binman. + This is used to create the final image. + +config SC5XX_ROOTFS_NAME + string "RootFS name" + default "rootfs" + depends on SC5XX_USE_BINMAN + help + The name of the rootfs to be packed by binman. + This is used to create the final image. +endmenu + config ADI_IMAGE string "ADI fitImage type" help
Signature · 1 line
2.45.2
PATCH 3/10 docker: add ADI build-related tools to docker image
In reply to Greg MalysaADI processors require packaging with the ldr utility for bootrom compatibility. Normally this is available as part of our yocto-derived toolchain but it is not a part of any other premade toolchain, so it is otherwise unavailable in the docker image for CI. This patch adds a source build from the ADI maintained github repository. The same ldr tool is used for arm and arm64 for all of our boards with names adjusted to match the expected $(CROSS_COMPILE) for these boards.
---
tools/docker/Dockerfile | 8 ++++++++ 1 file changed, 8 insertions(+)
tools/docker/Dockerfile +8 -0
@@ -308,6 +308,14 @@ RUN wget -O - https://coreboot.org/releases/coreboot-24.08.tar.xz | tar -C /tmp sudo cp build/coreboot.rom build/cbfstool /opt/coreboot/ && \ rm -rf /tmp/coreboot-24.08 +# Build ldr tool for ADI boards and install to match expected abi name +RUN git clone https://github.com/analogdevicesinc/lnxdsp-arm-poky-linux-gnueabi-ldr.git /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr && \ + cd /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr/src/ldr && \ + ./configure && \ + make -j $(nproc) && \ + cp ldr /usr/bin/arm-linux-gnueabi-ldr && \ + cp ldr /usr/bin/aarch64-linux-ldr + # Create our user/group RUN echo uboot ALL=NOPASSWD: ALL > /etc/sudoers.d/uboot RUN useradd -m -U uboot
Signature · 1 line
2.45.2
PATCH 4/10 board: adi: Add SOMCRR infrastructure
In reply to Greg MalysaThis adds infrastructure and shared library code for building targets that use the ADI SOMCRR-EZKIT and SOMCRR-EZLITE carrier boards. These are not used directly as board targets in their own right.
---
board/adi/carriers/Makefile | 8 +++++++ board/adi/carriers/somcrr.h | 14 +++++++++++ board/adi/carriers/somcrr_common.c | 19 +++++++++++++++ board/adi/carriers/somcrr_ezkit.c | 38 ++++++++++++++++++++++++++++++ board/adi/carriers/somcrr_ezlite.c | 24 +++++++++++++++++++ 5 files changed, 103 insertions(+) create mode 100644 board/adi/carriers/Makefile create mode 100644 board/adi/carriers/somcrr.h create mode 100644 board/adi/carriers/somcrr_common.c create mode 100644 board/adi/carriers/somcrr_ezkit.c create mode 100644 board/adi/carriers/somcrr_ezlite.c
board/adi/carriers/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2024 - Analog Devices, Inc. +# + +obj-y += somcrr_common.o +obj-$(CONFIG_ADI_CARRIER_SOMCRR_EZKIT) += somcrr_ezkit.o +obj-$(CONFIG_ADI_CARRIER_SOMCRR_EZLITE) += somcrr_ezlite.o
board/adi/carriers/somcrr.h new file +14 -0
@@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* +* (C) Copyright 2025 - Analog Devices, Inc. +* +*/ + +#ifndef BOARD_ADI_CARRIERS_SOMCRR_H +#define BOARD_ADI_CARRIERS_SOMCRR_H + +void adi_somcrr_init_ethernet (void ); +void adi_somcrr_enable_ethernet (void ); +void adi_somcrr_disable_ethernet (void ); + +#endif
board/adi/carriers/somcrr_common.c new file +19 -0
@@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <linux/delay.h> + +#include "somcrr.h" + +void adi_somcrr_init_ethernet (void ) +{ +adi_somcrr_enable_ethernet (); +mdelay (20 ); +adi_somcrr_disable_ethernet (); +mdelay (90 ); +adi_somcrr_enable_ethernet (); +mdelay (20 ); +}
board/adi/carriers/somcrr_ezkit.c new file +38 -0
@@ -0,0 +1,38 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <asm/gpio.h> + +#include "somcrr.h" + +void adi_somcrr_enable_ethernet (void ) +{ +struct gpio_desc *eth1; +struct gpio_desc *eth1_reset; +struct gpio_desc *gige_reset; + +gpio_hog_lookup_name ("~eth1-en" , ð1); +gpio_hog_lookup_name ("~eth1-reset" , ð1_reset); +gpio_hog_lookup_name ("~gige-reset" , &gige_reset); + +dm_gpio_set_value (eth1,1 ); +dm_gpio_set_value (eth1_reset,0 ); +dm_gpio_set_value (gige_reset,1 ); +} + +void adi_somcrr_disable_ethernet (void ) +{ +struct gpio_desc *eth1; +struct gpio_desc *eth1_reset; +struct gpio_desc *gige_reset; + +gpio_hog_lookup_name ("~eth1-en" , ð1); +gpio_hog_lookup_name ("~eth1-reset" , ð1_reset); +gpio_hog_lookup_name ("~gige-reset" , &gige_reset); + +dm_gpio_set_value (eth1,1 ); +dm_gpio_set_value (eth1_reset,0 ); +dm_gpio_set_value (gige_reset,0 ); +}
board/adi/carriers/somcrr_ezlite.c new file +24 -0
@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <asm/gpio.h> + +#include "somcrr.h" + +void adi_somcrr_enable_ethernet (void ) +{ +struct gpio_desc *gige_reset; + +gpio_hog_lookup_name ("~eth0-reset" , &gige_reset); +dm_gpio_set_value (gige_reset,1 ); +} + +void adi_somcrr_disable_ethernet (void ) +{ +struct gpio_desc *gige_reset; + +gpio_hog_lookup_name ("~eth0-reset" , &gige_reset); +dm_gpio_set_value (gige_reset,0 ); +}
Signature · 1 line
2.45.2
PATCH 5/10 board: adi: Add support for SC573-ezkit
In reply to Greg MalysaThis adds support for the Analog Devices SC573 EZKIT.
---
arch/arm/dts/sc573-ezkit.dts | 227 ++++++++++++++++++++++++++ arch/arm/dts/sc57x.dtsi | 123 +++++++++++++- board/adi/sc573-ezkit/Makefile | 6 + board/adi/sc573-ezkit/sc573-ezkit.c | 21 +++ board/adi/sc573-ezkit/sc573-ezkit.env | 17 +- configs/sc573-ezkit_defconfig | 102 ++++++++++++ 6 files changed, 486 insertions(+), 10 deletions(-) create mode 100644 board/adi/sc573-ezkit/Makefile create mode 100644 board/adi/sc573-ezkit/sc573-ezkit.c create mode 100644 configs/sc573-ezkit_defconfig
arch/arm/dts/sc573-ezkit.dts +227 -0
@@ -5,9 +5,236 @@ /dts-v1/; +#include "sc5xx.dtsi" #include "sc57x.dtsi" / { model = "ADI SC573-EZKIT"; compatible = "adi,sc573-ezkit", "adi,sc57x"; }; + +&i2c0 { + gpio_expander1: mcp23017@21 { + compatible = "microchip,mcp23017"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + eeprom { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~eeprom-en"; + bootph-pre-ram; + }; + + uart0-flow-en { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~uart0-flow-en"; + bootph-pre-ram; + }; + + mlb { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~mlb-en"; + bootph-pre-ram; + }; + + can0 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can0-en"; + bootph-pre-ram; + }; + + can1 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can1-en"; + bootph-pre-ram; + }; + + adau1962 { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1962-en"; + bootph-pre-ram; + }; + + adau1979 { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1979-en"; + bootph-pre-ram; + }; + + sd-wp-en { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~sd-wp-en"; + bootph-pre-ram; + }; + + spi2flash-cs { + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2flash-cs"; + bootph-pre-ram; + }; + + spi2d2-d3 { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2d2-d3-en"; + bootph-pre-ram; + }; + + spdif-opt { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-optical-en"; + bootph-pre-ram; + }; + + spdif-dig { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-digital-en"; + bootph-pre-ram; + }; + }; + + gpio_expander2: mcp23017@22 { + compatible = "microchip,mcp23017"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + pushbutton3 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~pushbutton3-en"; + bootph-pre-ram; + }; + + pushbutton2 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~pushbutton2-en"; + bootph-pre-ram; + }; + + pushbutton1 { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~pushbutton1-en"; + bootph-pre-ram; + }; + + leds { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~leds-en"; + bootph-pre-ram; + }; + + flg0 { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~flg0_loop"; + bootph-pre-ram; + }; + + flg1 { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~flg1_loop"; + bootph-pre-ram; + }; + + flg2 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~flg2_loop"; + bootph-pre-ram; + }; + + flg3 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~flg3_loop"; + bootph-pre-ram; + }; + + adau1977 { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~adau1977_en"; + bootph-pre-ram; + }; + + adau1977_fault_rst { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~adau1977_fault_rst_en"; + bootph-pre-ram; + }; + + thumbwheel { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~thumbwheel_oe"; + bootph-pre-ram; + }; + + engine_rpm { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~engine_rpm_oe"; + bootph-pre-ram; + }; + }; +}; + +ð0 { + snps,reset-gpio = <&gpio0 ADI_ADSP_PIN('A', 5) GPIO_ACTIVE_LOW>; +}; + +&gpio0 { + emac0_phy_pwdn { + gpio-hog; + output-high; + gpios = <ADI_ADSP_PIN('A', 4) GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc { + status = "okay"; +};
arch/arm/dts/sc57x.dtsi +119 -4
138 lines not on this page · raw message
board/adi/sc573-ezkit/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y += sc573-ezkit.o
board/adi/sc573-ezkit/sc573-ezkit.c new file +21 -0
@@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> + +int board_phy_config (struct phy_device *phydev) +{ +fixup_dp83867_phy (phydev); +return 0 ; +} + +int board_init (void ) +{ +sc5xx_enable_rgmii (); +return 0 ; +}
board/adi/sc573-ezkit/sc573-ezkit.env +11 -6
@@ -4,10 +4,15 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x20000 -adi_image_offset=0xE0000 -adi_rfs_offset=0x6E0000 -loadaddr=0x83000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc573-ezkit.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_SPI +#define USE_RAM +#define USE_MMC + +#include <env/adi/adi_boot.env>
configs/sc573-ezkit_defconfig new file +102 -0
102 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH 6/10 board: adi: Add support for SC589 boards
In reply to Greg MalysaThis adds support for the Analog Devices SC589-EZKIT and SC589-mini.
---
arch/arm/dts/sc589-ezkit.dts | 198 ++++++++++++++++++++++++++ arch/arm/dts/sc589-mini.dts | 18 ++- arch/arm/dts/sc58x.dtsi | 153 +++++++++++++++++++- board/adi/sc589-ezkit/Makefile | 6 + board/adi/sc589-ezkit/sc589-ezkit.c | 21 +++ board/adi/sc589-ezkit/sc589-ezkit.env | 17 ++- board/adi/sc589-mini/Makefile | 6 + board/adi/sc589-mini/sc589-mini.c | 21 +++ board/adi/sc589-mini/sc589-mini.env | 17 ++- configs/sc589-ezkit_defconfig | 113 +++++++++++++++ configs/sc589-mini_defconfig | 109 ++++++++++++++ 11 files changed, 663 insertions(+), 16 deletions(-) create mode 100644 board/adi/sc589-ezkit/Makefile create mode 100644 board/adi/sc589-ezkit/sc589-ezkit.c create mode 100644 board/adi/sc589-mini/Makefile create mode 100644 board/adi/sc589-mini/sc589-mini.c create mode 100644 configs/sc589-ezkit_defconfig create mode 100644 configs/sc589-mini_defconfig
arch/arm/dts/sc589-ezkit.dts +198 -0
@@ -8,6 +8,204 @@ #include "sc58x.dtsi" / { + #address-cells = <1>; + #size-cells = <1>; model = "ADI SC589-EZKIT"; compatible = "adi,sc589-ezkit", "adi,sc58x"; }; + +&i2c0 { + #address-cells = <1>; + #size-cells = <0>; + gpio_expander1: mcp23017@21 { + compatible = "microchip,mcp23017"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + eeprom { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~eeprom-en"; + bootph-pre-ram; + }; + + uart0-flow-en { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~uart0-flow-en"; + bootph-pre-ram; + }; + + uart0-en { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~uart0-en"; + bootph-pre-ram; + }; + + eth0 { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~eth0-en"; + bootph-pre-ram; + }; + + eth1 { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~eth1-en"; + bootph-pre-ram; + }; + + mlb { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~mlb-en"; + bootph-pre-ram; + }; + + can0 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can0-en"; + bootph-pre-ram; + }; + + can1 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can1-en"; + bootph-pre-ram; + }; + + adau1962 { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1962-en"; + bootph-pre-ram; + }; + + adau1979 { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1979-en"; + bootph-pre-ram; + }; + + sd_wp { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~sd-wp-en"; + bootph-pre-ram; + }; + + spi2d2-d3 { + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2d2-d3-en"; + bootph-pre-ram; + }; + + spi2flash-cs { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2flash-cs"; + bootph-pre-ram; + }; + + spdif-opt { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-optical-en"; + bootph-pre-ram; + }; + + spdif-dig { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-digital-en"; + bootph-pre-ram; + }; + }; + + gpio_expander2: mcp23017@22 { + compatible = "microchip,mcp23017"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + pushbutton1 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~pushbutton1-en"; + bootph-pre-ram; + }; + + pushbutton2 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~pushbutton2-en"; + bootph-pre-ram; + }; + + led10 { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~led10-en"; + bootph-pre-ram; + }; + + led11 { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~led11-en"; + bootph-pre-ram; + }; + + led12 { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~led12-en"; + bootph-pre-ram; + }; + }; +}; + +ð0 { + snps,reset-gpio = <&gpio0 ADI_ADSP_PIN('B', 14) GPIO_ACTIVE_LOW>; +}; + +&gpio0 { + emac0_phy_pwdn { + gpio-hog; + output-high; + gpios = <ADI_ADSP_PIN('C', 15) GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc { + status = "okay"; +};
arch/arm/dts/sc589-mini.dts +17 -1
@@ -8,6 +8,22 @@ #include "sc58x.dtsi" / { - model = "ADI SC598-MINI"; + model = "ADI SC589-MINI"; compatible = "adi,sc589-mini", "adi,sc58x"; }; + +ð0 { + snps,reset-gpio = <&gpio0 ADI_ADSP_PIN('B', 7) GPIO_ACTIVE_LOW>; +}; + +&gpio0 { + emac0_phy_pwdn { + gpio-hog; + output-high; + gpios = <ADI_ADSP_PIN('F', 6) GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc { + status = "okay"; +};
arch/arm/dts/sc58x.dtsi +150 -3
168 lines not on this page · raw message
board/adi/sc589-ezkit/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := sc589-ezkit.o
board/adi/sc589-ezkit/sc589-ezkit.c new file +21 -0
@@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> + +int board_phy_config (struct phy_device *phydev) +{ +fixup_dp83867_phy (phydev); +return 0 ; +} + +int board_init (void ) +{ +sc5xx_enable_rgmii (); +return 0 ; +}
board/adi/sc589-ezkit/sc589-ezkit.env +11 -6
@@ -4,10 +4,15 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x20000 -adi_image_offset=0xE0000 -adi_rfs_offset=0x6E0000 -loadaddr=0xC3000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc589-ezkit.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_RAM +#define USE_MMC +#define USE_SPI + +#include <env/adi/adi_boot.env>
board/adi/sc589-mini/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := sc589-mini.o
board/adi/sc589-mini/sc589-mini.c new file +21 -0
@@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> + +int board_phy_config (struct phy_device *phydev) +{ +fixup_dp83867_phy (phydev); +return 0 ; +} + +int board_init (void ) +{ +sc5xx_enable_rgmii (); +return 0 ; +}
board/adi/sc589-mini/sc589-mini.env +11 -6
@@ -4,10 +4,15 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x20000 -adi_image_offset=0xE0000 -adi_rfs_offset=0x8E0000 -loadaddr=0xC3000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc589-mini.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_RAM +#define USE_SPI +#define USE_MMC + +#include <env/adi/adi_boot.env>
configs/sc589-ezkit_defconfig new file +113 -0
113 lines not on this page · raw message
configs/sc589-mini_defconfig new file +109 -0
109 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH 7/10 board: adi: Add support for SC584
In reply to Greg MalysaThis adds support for the Analog Devices SC584-EZKIT.
---
arch/arm/dts/sc584-ezkit.dts | 230 ++++++++++++++++++++++++++ board/adi/sc584-ezkit/Makefile | 6 + board/adi/sc584-ezkit/sc584-ezkit.c | 21 +++ board/adi/sc584-ezkit/sc584-ezkit.env | 16 +- configs/sc584-ezkit_defconfig | 108 ++++++++++++ 5 files changed, 375 insertions(+), 6 deletions(-) create mode 100644 board/adi/sc584-ezkit/Makefile create mode 100644 board/adi/sc584-ezkit/sc584-ezkit.c create mode 100644 configs/sc584-ezkit_defconfig
arch/arm/dts/sc584-ezkit.dts +230 -0
@@ -11,3 +11,233 @@ model = "ADI SC584-EZKIT"; compatible = "adi,sc584-ezkit", "adi,sc58x"; }; + +&i2c2 { + gpio_expander1: mcp23017@21 { + compatible = "microchip,mcp23017"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + eeprom { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~eeprom-en"; + bootph-pre-ram; + }; + + uart0-flow-en { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~uart0-flow-en"; + bootph-pre-ram; + }; + + uart0-en { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~uart0-en"; + bootph-pre-ram; + }; + + mlb { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~mlb-en"; + bootph-pre-ram; + }; + + can0 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can0-en"; + bootph-pre-ram; + }; + + can1 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can1-en"; + bootph-pre-ram; + }; + + adau1962 { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1962-en"; + bootph-pre-ram; + }; + + adau1979 { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1979-en"; + bootph-pre-ram; + }; + + audio_jack_sel { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "audio_jack_sel"; + bootph-pre-ram; + }; + + spi2d2-d3 { + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2d2-d3-en"; + bootph-pre-ram; + }; + + spi2flash-cs { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~spi2flash-cs"; + bootph-pre-ram; + }; + + spdif-opt { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-optical-en"; + bootph-pre-ram; + }; + + spdif-dig { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-digital-en"; + bootph-pre-ram; + }; + }; + + gpio_expander2: mcp23017@22 { + compatible = "microchip,mcp23017"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + pushbutton3 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~pushbutton3-en"; + bootph-pre-ram; + }; + + pushbutton2 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~pushbutton2-en"; + bootph-pre-ram; + }; + + pushbutton1 { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~pushbutton1-en"; + bootph-pre-ram; + }; + + leds { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~leds-en"; + bootph-pre-ram; + }; + + flg0 { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~flg0_loop"; + bootph-pre-ram; + }; + + flg1 { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~flg1_loop"; + bootph-pre-ram; + }; + + flg2 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~flg2_loop"; + bootph-pre-ram; + }; + + flg3 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~flg3_loop"; + bootph-pre-ram; + }; + + adau1977 { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~adau1977_en"; + bootph-pre-ram; + }; + + adau1977_fault_rst { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~adau1977_fault_rst_en"; + bootph-pre-ram; + }; + + thumbwheel { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~thumbwheel_oe"; + bootph-pre-ram; + }; + + engine_rpm { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~engine_rpm_oe"; + bootph-pre-ram; + }; + }; +}; + +ð0 { + snps,reset-gpio = <&gpio0 ADI_ADSP_PIN('B', 14) GPIO_ACTIVE_LOW>; +}; + +&gpio0 { + emac0_phy_pwdn { + gpio-hog; + output-high; + gpios = <ADI_ADSP_PIN('C', 15) GPIO_ACTIVE_HIGH>; + }; +};
board/adi/sc584-ezkit/Makefile new file +6 -0
@@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := sc584-ezkit.o
board/adi/sc584-ezkit/sc584-ezkit.c new file +21 -0
@@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> + +int board_phy_config (struct phy_device *phydev) +{ +fixup_dp83867_phy (phydev); +return 0 ; +} + +int board_init (void ) +{ +sc5xx_enable_rgmii (); +return 0 ; +}
board/adi/sc584-ezkit/sc584-ezkit.env +10 -6
@@ -4,10 +4,14 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x20000 -adi_image_offset=0xE0000 -adi_rfs_offset=0x6E0000 -loadaddr=0x89300000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc584-ezkit.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_SPI +#define USE_RAM + +#include <env/adi/adi_boot.env>
configs/sc584-ezkit_defconfig new file +108 -0
108 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH 8/10 board: adi: Add support for SC598
In reply to Greg MalysaThis adds support for the Analog Devices SC598-SOM and configurations for using it with both the SOMCRR-EZKIT and SOMCRR-EZLITE.
---
arch/arm/dts/sc598-som-ezkit.dts | 166 ++++++++++++ arch/arm/dts/sc598-som-ezlite.dts | 82 ++++++ arch/arm/dts/sc598-som.dtsi | 237 +++++++++++++++++- arch/arm/dts/sc59x.dtsi | 183 ++++++++++++++ arch/arm/dts/sc5xx.dtsi | 137 +++++++++- board/adi/common-sc598-som/sc598-som.c | 34 +++ board/adi/sc598-som-ezkit/Makefile | 8 + board/adi/sc598-som-ezkit/sc598-som-ezkit.env | 18 +- board/adi/sc598-som-ezlite/Makefile | 8 + .../adi/sc598-som-ezlite/sc598-som-ezlite.env | 12 +- configs/sc598-som-ezkit-spl_defconfig | 123 +++++++++ configs/sc598-som-ezlite-spl_defconfig | 123 +++++++++ 12 files changed, 1105 insertions(+), 26 deletions(-) create mode 100644 arch/arm/dts/sc59x.dtsi create mode 100644 board/adi/common-sc598-som/sc598-som.c create mode 100644 board/adi/sc598-som-ezkit/Makefile create mode 100644 board/adi/sc598-som-ezlite/Makefile create mode 100644 configs/sc598-som-ezkit-spl_defconfig create mode 100644 configs/sc598-som-ezlite-spl_defconfig
arch/arm/dts/sc598-som-ezkit.dts +166 -0
@@ -11,3 +11,169 @@ model = "ADI SC598-SOM-EZKIT"; compatible = "adi,sc598-som-ezkit", "adi,sc59x-64"; }; + +&i2c2{ + gpio_expander2: mcp23017@22 { + compatible = "microchip,mcp23017"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + eeprom { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "eeprom-en"; + bootph-pre-ram; + }; + + pushbutton { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "pushbutton-en"; + bootph-pre-ram; + }; + + microsd { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~microsd-spi"; + bootph-pre-ram; + }; + + ftdi { + gpio-hog; + gpios = <3 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~ftdi-usb-en"; + bootph-pre-ram; + }; + + can { + gpio-hog; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~can-en"; + bootph-pre-ram; + }; + + adau1962 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "adau1962-en"; + bootph-pre-ram; + }; + + adau1979 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "adau1979-en"; + bootph-pre-ram; + }; + + octal { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "octal-spi-cs-en"; + bootph-pre-ram; + }; + + spdif-dig { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-digital-en"; + bootph-pre-ram; + }; + + spdif-opt { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-optical-en"; + bootph-pre-ram; + }; + + audio-jack { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "audio-jack-sel"; + bootph-pre-ram; + }; + + mlb { + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~mlb-en"; + bootph-pre-ram; + }; + + eth1 { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~eth1-en"; + bootph-pre-ram; + }; + + eth1-reset { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + /* + * USB0 lines are shared with Eth1 so Eth PHY must be held in reset + * when using the USB + */ + output-low; + line-name = "~eth1-reset"; + bootph-pre-ram; + }; + + gige-reset { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~gige-reset"; + bootph-pre-ram; + }; + }; +}; + +&ospi { + status = "okay"; + + clocks = <&clk ADSP_SC598_CLK_OSPI_REFCLK>; + + flash0: mx66lm1g45@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor", "mx66lm1g45"; + reg = <0>; + + /* + * This is board dependent to some extent. We've been able to + *set it higher on some boards + */ + spi-max-frequency = <66666666>; + cdns,spi-calib-frequency = <10000000>; + + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + + tshsl-ns = <50>; + tsd2d-ns = <50>; + tchsh-ns = <4>; + tslch-ns = <4>; + bootph-pre-ram; + + cdns,dqs; + cdns,phy; + }; +};
arch/arm/dts/sc598-som-ezlite.dts +82 -0
85 lines not on this page · raw message
arch/arm/dts/sc598-som.dtsi +234 -3
257 lines not on this page · raw message
arch/arm/dts/sc59x.dtsi new file +183 -0
183 lines not on this page · raw message
arch/arm/dts/sc5xx.dtsi +126 -11
177 lines not on this page · raw message
board/adi/common-sc598-som/sc598-som.c new file +34 -0
@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <config.h> +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> +#include <asm/armv8/mmu.h> + +#include "../carriers/somcrr.h" + +int board_phy_config (struct phy_device *phydev) +{ +if (IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZKIT )) +fixup_dp83867_phy (phydev); +return 0 ; +} + +int board_init (void ) +{ +sc59x_remap_ospi (); + +if (IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZKIT ) || +IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZLITE )) { +adi_somcrr_init_ethernet (); + } + +sc5xx_enable_rgmii (); + +return 0 ; +}
board/adi/sc598-som-ezkit/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := ../common-sc598-som/sc598-som.o + +obj-y += ../carriers/
board/adi/sc598-som-ezkit/sc598-som-ezkit.env +12 -6
@@ -4,10 +4,16 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x40000 -adi_image_offset=0x01a0000 -adi_rfs_offset=0x1020000 -loadaddr=0x90000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc598-som-ezkit.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_SPI +#define USE_OSPI +#define USE_RAM +#define USE_MMC + +#include <env/adi/adi_boot.env>
board/adi/sc598-som-ezlite/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := ../common-sc598-som/sc598-som.o + +obj-y += ../carriers/
board/adi/sc598-som-ezlite/sc598-som-ezlite.env +6 -6
@@ -4,10 +4,10 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x40000 -adi_image_offset=0x01a0000 -adi_rfs_offset=0x1020000 -loadaddr=0x90000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET +loadaddr=CONFIG_SC5XX_LOADADDR jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc598-som-ezlite.jffs2 + +#include <env/adi/adi_boot.env>
configs/sc598-som-ezkit-spl_defconfig new file +123 -0
123 lines not on this page · raw message
configs/sc598-som-ezlite-spl_defconfig new file +123 -0
123 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH 9/10 board: adi: Add support for SC594
In reply to Greg MalysaThis adds support for the Analog Devices SC594 SOM and configurations for using it with both the SOMCRR-EZKIT and SOMCRR-EZLITE.
---
arch/arm/dts/sc594-som-ezkit.dts | 126 ++++++++++++ arch/arm/dts/sc594-som-ezlite.dts | 83 ++++++++ arch/arm/dts/sc594-som.dtsi | 184 +++++++++++++++++- board/adi/common-sc594-som/sc594-som.c | 34 ++++ board/adi/sc594-som-ezkit/Makefile | 8 + board/adi/sc594-som-ezkit/sc594-som-ezkit.env | 18 +- board/adi/sc594-som-ezlite/Makefile | 8 + .../adi/sc594-som-ezlite/sc594-som-ezlite.env | 18 +- configs/sc594-som-ezkit-spl_defconfig | 90 +++++++++ configs/sc594-som-ezlite-spl_defconfig | 98 ++++++++++ 10 files changed, 652 insertions(+), 15 deletions(-) create mode 100644 board/adi/common-sc594-som/sc594-som.c create mode 100644 board/adi/sc594-som-ezkit/Makefile create mode 100644 board/adi/sc594-som-ezlite/Makefile create mode 100644 configs/sc594-som-ezkit-spl_defconfig create mode 100644 configs/sc594-som-ezlite-spl_defconfig
arch/arm/dts/sc594-som-ezkit.dts +126 -0
@@ -11,3 +11,129 @@ model = "ADI SC594-SOM-EZKIT"; compatible = "adi,sc594-som-ezkit", "adi,sc59x"; }; + +&i2c2{ + gpio_expander2: mcp23017@22 { + compatible = "microchip,mcp23017"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + bootph-pre-ram; + + eeprom { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "eeprom-en"; + bootph-pre-ram; + }; + + pushbutton { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "pushbutton-en"; + bootph-pre-ram; + }; + + microsd { + gpio-hog; + gpios = <2 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~microsd-spi"; + bootph-pre-ram; + }; + + adau-reset { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "adau-reset"; + bootph-pre-ram; + }; + + adau1962 { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "adau1962-en"; + bootph-pre-ram; + }; + + adau1979 { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "adau1979-en"; + bootph-pre-ram; + }; + + octal { + gpio-hog; + gpios = <8 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "octal-spi-cs-en"; + bootph-pre-ram; + }; + + spdif-dig { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-digital-en"; + bootph-pre-ram; + }; + + spdif-opt { + gpio-hog; + gpios = <10 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~spdif-optical-en"; + bootph-pre-ram; + }; + + audio-jack { + gpio-hog; + gpios = <11 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "audio-jack-sel"; + bootph-pre-ram; + }; + + mlb { + gpio-hog; + gpios = <12 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~mlb-en"; + bootph-pre-ram; + }; + + eth1 { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "~eth1-en"; + bootph-pre-ram; + }; + + eth1-reset { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + /* + * USB0 lines are shared with Eth1 so Eth PHY must be held in reset + * when using the USB + */ + output-low; + line-name = "~eth1-reset"; + bootph-pre-ram; + }; + + gige-reset { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "~gige-reset"; + bootph-pre-ram; + }; + }; +};
arch/arm/dts/sc594-som-ezlite.dts +83 -0
86 lines not on this page · raw message
arch/arm/dts/sc594-som.dtsi +181 -3
195 lines not on this page · raw message
board/adi/common-sc594-som/sc594-som.c new file +34 -0
@@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* +* (C) Copyright 2025 - Analog Devices, Inc. +*/ + +#include <config.h> +#include <phy.h> +#include <asm/u-boot.h> +#include <asm/arch-adi/sc5xx/sc5xx.h> +#include <asm/arch-adi/sc5xx/soc.h> + +#include "../carriers/somcrr.h" + +int board_phy_config (struct phy_device *phydev) +{ +if (IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZKIT )) +fixup_dp83867_phy (phydev); + +return 0 ; +} + +int board_init (void ) +{ +sc59x_remap_ospi (); + +if (IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZKIT ) || +IS_ENABLED (CONFIG_ADI_CARRIER_SOMCRR_EZLITE )) { +adi_somcrr_init_ethernet (); + } + +sc5xx_enable_rgmii (); + +return 0 ; +}
board/adi/sc594-som-ezkit/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := ../common-sc594-som/sc594-som.o + +obj-y += ../carriers/
board/adi/sc594-som-ezkit/sc594-som-ezkit.env +12 -6
@@ -4,10 +4,16 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x40000 -adi_image_offset=0x0120000 -adi_rfs_offset=0x1020000 -loadaddr=0xA2000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc594-som-ezkit.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_SPI +#define USE_OSPI +#define USE_RAM +#define USE_MMC + +#include <env/adi/adi_boot.env>
board/adi/sc594-som-ezlite/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# +# (C) Copyright 2025 - Analog Devices, Inc. +# + +obj-y := ../common-sc594-som/sc594-som.o + +obj-y += ../carriers/
board/adi/sc594-som-ezlite/sc594-som-ezlite.env +12 -6
@@ -4,10 +4,16 @@ * (C) Copyright 2024 - Analog Devices, Inc. */ -#include <env/adi/adi_boot.env> - -adi_stage2_offset=0x40000 -adi_image_offset=0x0120000 -adi_rfs_offset=0x1020000 -loadaddr=0xA2000000 +adi_stage2_offset=CONFIG_SC5XX_UBOOT_OFFSET +adi_image_offset=CONFIG_SC5XX_FITIMAGE_OFFSET +adi_rfs_offset=CONFIG_SC5XX_ROOTFS_OFFSET jffs2file=adsp-sc5xx-__stringify(CONFIG_ADI_IMAGE)-adsp-sc594-som-ezlite.jffs2 +loadaddr=CONFIG_SC5XX_LOADADDR + +#define USE_NFS +#define USE_SPI +#define USE_OSPI +#define USE_RAM +#define USE_MMC + +#include <env/adi/adi_boot.env>
configs/sc594-som-ezkit-spl_defconfig new file +90 -0
90 lines not on this page · raw message
configs/sc594-som-ezlite-spl_defconfig new file +98 -0
98 lines not on this page · raw message
Signature · 1 line
2.45.2
PATCH 10/10 MAINTAINERS: Update ADI entries for new boards
In reply to Greg MalysaThis adds missing maintainers entries for the ADI SC5xx defconfigs.
---
MAINTAINERS | 1 + 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
@@ -631,6 +631,7 @@ F: arch/arm/dts/sc5* F: arch/arm/include/asm/arch-adi/ F: arch/arm/mach-sc5xx/ F: board/adi/ +F: configs/sc5* F: doc/device-tree-bindings/arm/adi/adi,sc5xx.yaml F: doc/device-tree-bindings/clock/adi,sc5xx-clocks.yaml F: doc/device-tree-bindings/pinctrl/adi,adsp-pinctrl.yaml
Signature · 1 line
2.45.2
Re: [PATCH 03/10] docker: add ADI build-related tools to docker image
In reply to Greg MalysaAm 2. Juni 2025 21:44:41 MESZ schrieb Greg Malysa <[email protected]>:
Quoted 1 line
ADI processors require packaging with the ldr utility for bootrom
"ADI processors" is not self explanatory. Can we add a sentence like
"LDR files are the executable format for the Analog Devices ADSP-SCxxx on-chip Boot ROM. Provide the ldr compiler for ARMv7 and ARMv8."
Quoted 18 lines
compatibility. Normally this is available as part of our yocto-derived toolchain but it is not a part of any other premade toolchain, so it is otherwise unavailable in the docker image for CI. This patch adds a source build from the ADI maintained github repository. The same ldr tool is used for arm and arm64 for all of our boards with names adjusted to match the expected $(CROSS_COMPILE) for these boards.
Signed-off-by Greg Malysa <[email protected]>---
tools/docker/Dockerfile| 8 ++++++++1 file changed, 8 insertions(+)tools/docker/Dockerfile +0
-0
tools/docker/Dockerfile RUN wget -O - https://coreboot.org/releases/coreboot-24.08.tar.xz | tar -C /tmp · line 317
Quoted 10 lines
tools/docker/Dockerfile +7
-0@@ -308,6 +308,14 @@ RUN wget -O - https://coreboot.org/releases/coreboot-24.08.tar.xz | tar -C /tmp sudo cp build/coreboot.rom build/cbfstool /opt/coreboot/ && \ rm -rf /tmp/coreboot-24.08 +# Build ldr tool for ADI boards and install to match expected abi name +RUN git clone https://github.com/analogdevicesinc/lnxdsp-arm-poky-linux-gnueabi-ldr.git /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr && \ + cd /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr/src/ldr && \ + ./configure && \ + make -j $(nproc) && \ + cp ldr /usr/bin/arm-linux-gnueabi-ldr && \ + cp ldr /usr/bin/aarch64-linux-ldr
In the Docker image we tend to put such tools into a directory in /opt.
Best regards
Heinrich
Quoted 4 lines
tools/docker/Dockerfile +1
-0+ # Create our user/groupRUN echo uboot ALL=NOPASSWD: ALL >
/etc/sudoers.d/ubootRUN useradd -m -U uboot
PATCH 3/10 docker: add ADI build-related tools to docker image
In reply to a message not in the archiveMy apologies, I accidentally didn't hit reply to all, please see below.
---------- Forwarded message ---------
From: Greg Malysa <[email protected]>
Date: Tue, Jun 3, 2025 at 3:04 AM
Subject: Re: [PATCH 03/10] docker: add ADI build-related tools to docker image
To: Heinrich Schuchardt <[email protected]>
Hi Heinrich,
Quoted 7 lines · Heinrich Schuchardt
Am 2. Juni 2025 21:44:41 MESZ schrieb Greg Malysa <[email protected]>:
Quoted 1 line
ADI processors require packaging with the ldr utility for bootrom
"ADI processors" is not self explanatory. Can we add a sentence like
"LDR files are the executable format for the Analog Devices ADSP-SCxxx on-chip Boot ROM. Provide the ldr compiler for ARMv7 and ARMv8."
Yes I can update the message with text like this for v2.
Quoted 11 lines
tools/docker/Dockerfile RUN wget -O - https://coreboot.org/releases/coreboot-24.08.tar.xz | tar -C /tmp · line 317
Quoted 9 lines
tools/docker/Dockerfile +7
-0+# Build ldr tool for ADI boards and install to match expected abi name +RUN git clone https://github.com/analogdevicesinc/lnxdsp-arm-poky-linux-gnueabi-ldr.git /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr && \ + cd /tmp/lnxdsp-arm-poky-linux-gnueabi-ldr/src/ldr && \ + ./configure && \ + make -j $(nproc) && \ + cp ldr /usr/bin/arm-linux-gnueabi-ldr && \ + cp ldr /usr/bin/aarch64-linux-ldrIn the Docker image we tend to put such tools into a directory in /opt.
I will make this change as well and run through CI again on my runner. I'll wait a week or so for feedback on the rest of the series before resubmitting. Thanks for the feedback!
Thanks,
Greg
Re: [PATCH 10/10] MAINTAINERS: Update ADI entries for new boards
In reply to Greg MalysaQuoted 17 lines · Greg Malysa
This adds missing maintainers entries for the ADI SC5xx defconfigs.
Signed-off-by Vasileios Bimpikas <[email protected]>Signed-off-by Utsav Agarwal <[email protected]>Signed-off-by Arturs Artamonovs <[email protected]>Signed-off-by Nathan Barrett-Morrison <[email protected]>Signed-off-by Greg Malysa <[email protected]>---
MAINTAINERS | 1 + 1 file changed, 1 insertion(+)MAINTAINERS +0
-0
MAINTAINERS F: arch/arm/dts/sc5* · line 637
Quoted 7 lines
MAINTAINERS +1
-0@@ -631,6 +631,7 @@ F: arch/arm/dts/sc5* F: arch/arm/include/asm/arch-adi/ F: arch/arm/mach-sc5xx/ F: board/adi/ +F: configs/sc5* F: doc/device-tree-bindings/arm/adi/adi,sc5xx.yaml F: doc/device-tree-bindings/clock/adi,sc5xx-clocks.yaml F: doc/device-tree-bindings/pinctrl/adi,adsp-pinctrl.yaml
This doesn't also catch the other drivers and so forth added. Perhaps the "N: " regex syntax would be helpful here, to make adding all of those as well easier? Thanks.
Signature · 1 line
Tom
Re: [PATCH 10/10] MAINTAINERS: Update ADI entries for new boards
Hi Tom,
Quoted 15 lines · Tom Rini
Quoted 12 lines · Greg Malysa
This adds missing maintainers entries for the ADI SC5xx defconfigs.
Signed-off-by Vasileios Bimpikas <[email protected]>Signed-off-by Utsav Agarwal <[email protected]>Signed-off-by Arturs Artamonovs <[email protected]>Signed-off-by Nathan Barrett-Morrison <[email protected]>Signed-off-by Greg Malysa <[email protected]>---
MAINTAINERS | 1 + 1 file changed, 1 insertion(+)
Quoted 16 lines
MAINTAINERS F: arch/arm/dts/sc5* · line 637
Quoted 12 lines
MAINTAINERS +1
-0@@ -631,6 +631,7 @@ F: arch/arm/dts/sc5* F: arch/arm/include/asm/arch-adi/ F: arch/arm/mach-sc5xx/ F: board/adi/ +F: configs/sc5* F: doc/device-tree-bindings/arm/adi/adi,sc5xx.yaml F: doc/device-tree-bindings/clock/adi,sc5xx-clocks.yaml F: doc/device-tree-bindings/pinctrl/adi,adsp-pinctrl.yamlThis doesn't also catch the other drivers and so forth added. Perhaps the "N: " regex syntax would be helpful here, to make adding all of those as well easier? Thanks.
Thanks for the feedback, I'll review the names again before v2 and look for any missed entries. Our names are a bit inconsistent: some adi, some adsp, some include sc5xx and some do not. In v2 of this series we could rename the defconfigs to adhere to a useful, specific naming convention, and then follow up by renaming drivers across different subsystems in a separate series so that we can have one N:
line and catch them all. Do you have any tips on tracking down files that are missed? Using scripts/get_maintainer.pl with a list of what I think the files are could work but I won't know if I forgot something that way :-). Is there a particular way to invoke it that checks all files, perhaps, and reports on files that are missing supporters?
Thanks,
Greg
Re: [PATCH 10/10] MAINTAINERS: Update ADI entries for new boards
Quoted 35 lines · Greg Malysa
Hi Tom,
Quoted 15 lines · Tom Rini
Quoted 12 lines · Greg Malysa
This adds missing maintainers entries for the ADI SC5xx defconfigs.
Signed-off-by Vasileios Bimpikas <[email protected]>Signed-off-by Utsav Agarwal <[email protected]>Signed-off-by Arturs Artamonovs <[email protected]>Signed-off-by Nathan Barrett-Morrison <[email protected]>Signed-off-by Greg Malysa <[email protected]>---
MAINTAINERS | 1 + 1 file changed, 1 insertion(+)Quoted 16 lines
MAINTAINERS F: arch/arm/dts/sc5* · line 637
Quoted 12 lines
MAINTAINERS +1
-0@@ -631,6 +631,7 @@ F: arch/arm/dts/sc5* F: arch/arm/include/asm/arch-adi/ F: arch/arm/mach-sc5xx/ F: board/adi/ +F: configs/sc5* F: doc/device-tree-bindings/arm/adi/adi,sc5xx.yaml F: doc/device-tree-bindings/clock/adi,sc5xx-clocks.yaml F: doc/device-tree-bindings/pinctrl/adi,adsp-pinctrl.yamlThis doesn't also catch the other drivers and so forth added. Perhaps the "N: " regex syntax would be helpful here, to make adding all of those as well easier? Thanks.
Quoted 11 lines
Thanks for the feedback, I'll review the names again before v2 and look for any missed entries. Our names are a bit inconsistent: some adi, some adsp, some include sc5xx and some do not. In v2 of this series we could rename the defconfigs to adhere to a useful, specific naming convention, and then follow up by renaming drivers across different subsystems in a separate series so that we can have one N:
line and catch them all. Do you have any tips on tracking down files that are missed? Usingscripts/get_maintainer.plwith a list of what I think the files are could work but I won't know if I forgot something that way :-). Is there a particular way to invoke it that checks all files, perhaps, and reports on files that are missing supporters?
Sadly it's a manual process.
Signature · 1 line
Tom