Skip to contentSkip to conversation

clk: spacemit: mark K1 pll1_d8 as critical

PATCH In review Alex Elder 4 participants 8 messages Jun 7, 2025 – Jun 9, 2025

Subsystems (3)
lore
Share & tools
lore

Alex Elder

author
#0 lore raw

PATCH 1/1 clk: spacemit: mark K1 pll1_d8 as critical

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA, adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
 drivers/clk/spacemit/ccu-k1.c  |  3 ++-
 drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
 2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
 CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
 CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +13 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
 	}									\
 }
 
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
 #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
 			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
 
 #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
 			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2
#1 lore raw

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

Quoted 66 lines

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
 drivers/clk/spacemit/ccu-k1.c  |  3 ++-
 drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
 2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
 CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
 CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
 CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +13 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
 	}									\
 }
 
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
 #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
 			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
 
 #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
 			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2
Signature · 1 line
Yixun Lan (dlan)
author
#2 lore raw
Quoted 6 lines · Yixun Lan

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

I will give you a full explanation of what I observed, below.

Quoted 11 lines
Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper

No, that is not the issue. The reset is never deasserted.

Quoted 2 lines

order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

The problem is with the pll1_d8 clock. That clock is enabled successfully. However the reset isn't ready, so the clock gets disabled, and its parent (and other ancestors) also get disabled while recovering from that.

I'll give you a high-level summary, then will lay out a ton of detail.

In the DMA driver probe function, several initial things happen and then, a clock is requested (enabled):
<&syscon_apmu CLK_DMA>
That succeeds.

Next, a reset is requested:
<&syscon_apmu RESET_DMA>
But that fails, because the reset driver probe function hasn't been called yet. The request gets -EPROBE_DEFER as its result, and the DMA driver starts unwinding everything so that it can be probed again later. Dropping the clock reference results in parent clocks dropping references. And because pll1_div8 initially had a reference count of 0 (despite being on), dropping this single reference means it gets disabled. Then we're stuck.

Here is how the DMA clock is supplied (at boot time):

pll1 -> pll1_d8 -> pll1_d8_307p2 -> pmua_aclk -> dma_clk

pll1 and pll1_d8 are enabled by the boot loader, but at this time the drivers for various hardware that require them aren't "getting" and enabling them (yet).

devm_clk_get_optional_enabled() causes clk_prepare_enable() to be called on the target clock (pll1_d8). That simply calls clk_prepare() and clk_enable(). Let's focus on the latter.
clk_enable(dma_clk)
clk_core_enable_lock()

So now the clock enable lock is held. The target clock's enable_count for pll1_d8 is 0.

clk_core_enable(dma_clk)
clk_core_enable(parent = pmua_aclk)
...
enable_count++ (on dma_clk)

The parent gets enabled (I'm fairly certain pmua_clk's enable_count is also 0).

clk_core_enable(pmua_aclk)

    clk_core_enable(parent = pll1_d8_307p2)
    ...
    enable_count++ (on pmua_clk)

And so on. When the clk_enable(dma_clk) completes, we have these enable counts:
dma_clk: 1
pmua_clk: 1
pll1_d8_307p2: 1
pll1_d8: 1
pll1: 1? (I don't recall)

The -EPROBE_DEFER causes the devm_clk_get_optional_enabled() for dma_clk to get undone. That means clk_disable_unprepare() gets called on dma_clk. Let's just focus on clk_disable().

clk_disable(dma_clk)
clk_core_disable_lock(dma_clk)
(takes clk_enable lock) clk_core_disable()
--enable_count becomes 0 (on dma_clk) (disables dma_clk) clk_core_disable(core->parent = pmua_aclk)

clk_core_disable(pmua_aclk)
--enable_count becomes 0 (on pmua_clk) (disables pmua_clk) clk_core_dissable(core->parent = pll1_d8_307p2)

clk_core_disable(pll1_d8_307p2)

    --enable_count becomes 0 (on pll1_d8_307p2)
    (disables pll1_d8_307p2)
    clk_core_dissable(core->parent = pll1_d8)

clk_core_disable(pll1_d8\)
--enable_count becomes 0 (on pll1)
(disables pll1_d8)
BOOM

I hope this is clear.

-Alex

Quoted 67 lines
Quoted 66 lines

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
  drivers/clk/spacemit/ccu-k1.c  |  3 ++-
  drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
  2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
  CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
  CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +13 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
  	}									\
  }
 
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
  #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
  			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
 
  #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
  			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2
#3 lore raw
Quoted 108 lines · Alex Elder
Quoted 6 lines · Yixun Lan

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

I will give you a full explanation of what I observed, below.

Quoted 11 lines
Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper

No, that is not the issue. The reset is never deasserted.

Quoted 2 lines

order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

The problem is with the pll1_d8 clock. That clock is enabled successfully. However the reset isn't ready, so the clock gets disabled, and its parent (and other ancestors) also get disabled while recovering from that.

I'll give you a high-level summary, then will lay out a ton of detail.

In the DMA driver probe function, several initial things happen and then, a clock is requested (enabled):
<&syscon_apmu CLK_DMA>
That succeeds.

Next, a reset is requested:
<&syscon_apmu RESET_DMA>
But that fails, because the reset driver probe function hasn't been called yet. The request gets -EPROBE_DEFER as its result, and the DMA driver starts unwinding everything so that it can be probed again later. Dropping the clock reference results in parent clocks dropping references. And because pll1_div8 initially had a reference count of 0 (despite being on), dropping this single reference means it gets disabled. Then we're stuck.

Here is how the DMA clock is supplied (at boot time):

pll1 -> pll1_d8 -> pll1_d8_307p2 -> pmua_aclk -> dma_clk

pll1 and pll1_d8 are enabled by the boot loader, but at this time the drivers for various hardware that require them aren't "getting" and enabling them (yet).

devm_clk_get_optional_enabled() causes clk_prepare_enable() to be called on the target clock (pll1_d8). That simply calls clk_prepare() and clk_enable(). Let's focus on the latter.
clk_enable(dma_clk)
clk_core_enable_lock()

So now the clock enable lock is held. The target clock's enable_count for pll1_d8 is 0.

clk_core_enable(dma_clk)
clk_core_enable(parent = pmua_aclk)
...
enable_count++ (on dma_clk)

The parent gets enabled (I'm fairly certain pmua_clk's enable_count is also 0).

clk_core_enable(pmua_aclk)

    clk_core_enable(parent = pll1_d8_307p2)
    ...
    enable_count++ (on pmua_clk)

And so on. When the clk_enable(dma_clk) completes, we have these enable counts:
dma_clk: 1
pmua_clk: 1
pll1_d8_307p2: 1
pll1_d8: 1
pll1: 1? (I don't recall)

The -EPROBE_DEFER causes the devm_clk_get_optional_enabled() for dma_clk to get undone. That means clk_disable_unprepare() gets called on dma_clk. Let's just focus on clk_disable().

clk_disable(dma_clk)
clk_core_disable_lock(dma_clk)
(takes clk_enable lock) clk_core_disable()
--enable_count becomes 0 (on dma_clk) (disables dma_clk) clk_core_disable(core->parent = pmua_aclk)

clk_core_disable(pmua_aclk)
--enable_count becomes 0 (on pmua_clk) (disables pmua_clk) clk_core_dissable(core->parent = pll1_d8_307p2)

clk_core_disable(pll1_d8_307p2)

Quoted 8 lines
    --enable_count becomes 0 (on pll1_d8_307p2)
    (disables pll1_d8_307p2)
    clk_core_dissable(core->parent = pll1_d8)

clk_core_disable(pll1_d8\)
--enable_count becomes 0 (on pll1)
(disables pll1_d8)
BOOM

Yeah, I got the reason that pll1_d8 is disabled, but I don't still understand why it matters: pll1_d8 is a simple factor gate, though being parent of various peripheral clocks, it's okay to enable it again later if some peripherals decide to use it or one of its child, isn't it?

I could come up with several scenarios where disabling the clock really causes problems,

1. Some essential SoC components are actually supplied by pll1_d8 or one of its children, but isn't described in devicetree or the driver, thus disabling pll1_d8 leads to an SoC hang. We should mark the precise clock that being essential as critcal, instead of setting pll1_d8 as critical to work around the problem.
2. There're bugs in our clock driver, thus it fails to bring pll1_d8 (or maybe also its children) back to a sound state. If so we should fix the driver.

Unless you could confirm pll1_d8 (not its child) really supplies some essential SoC components, I don't think simply marking pll1_d8 as critical is the correct solution.

And, I don't even know what "non-functioning system" behaves like. Could you please provide more information, like soC behaviours or dmesg when disabling pll1_d8 causes problems? Thanks.

Quoted 3 lines

I hope this is clear.

-Alex

Regards,
Haylen Chu

Quoted 58 lines
Quoted 58 lines
Quoted 58 lines

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
  drivers/clk/spacemit/ccu-k1.c  |  3 ++-
  drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
  2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
  CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
  CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
  CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +11 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
  	}									\
  }
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
  #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
  			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
Quoted 9 lines
Quoted 8 lines
Quoted 7 lines
drivers/clk/spacemit/ccu_mix.h +2 -0
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
  #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
  			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2

_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv

#4 lore raw

Hi Alex, Haylen,

Quoted 123 lines · Haylen Chu
Quoted 108 lines · Alex Elder
Quoted 6 lines · Yixun Lan

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

I will give you a full explanation of what I observed, below.

Quoted 11 lines
Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper

No, that is not the issue. The reset is never deasserted.

Quoted 2 lines

order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

The problem is with the pll1_d8 clock. That clock is enabled successfully. However the reset isn't ready, so the clock gets disabled, and its parent (and other ancestors) also get disabled while recovering from that.

I'll give you a high-level summary, then will lay out a ton of detail.

In the DMA driver probe function, several initial things happen and then, a clock is requested (enabled):
<&syscon_apmu CLK_DMA>
That succeeds.

Next, a reset is requested:
<&syscon_apmu RESET_DMA>
But that fails, because the reset driver probe function hasn't been called yet. The request gets -EPROBE_DEFER as its result, and the DMA driver starts unwinding everything so that it can be probed again later. Dropping the clock reference results in parent clocks dropping references. And because pll1_div8 initially had a reference count of 0 (despite being on), dropping this single reference means it gets disabled. Then we're stuck.

Here is how the DMA clock is supplied (at boot time):

pll1 -> pll1_d8 -> pll1_d8_307p2 -> pmua_aclk -> dma_clk

pll1 and pll1_d8 are enabled by the boot loader, but at this time the drivers for various hardware that require them aren't "getting" and enabling them (yet).

devm_clk_get_optional_enabled() causes clk_prepare_enable() to be called on the target clock (pll1_d8). That simply calls clk_prepare() and clk_enable(). Let's focus on the latter.
clk_enable(dma_clk)
clk_core_enable_lock()

So now the clock enable lock is held. The target clock's enable_count for pll1_d8 is 0.

clk_core_enable(dma_clk)
clk_core_enable(parent = pmua_aclk)
...
enable_count++ (on dma_clk)

The parent gets enabled (I'm fairly certain pmua_clk's enable_count is also 0).

clk_core_enable(pmua_aclk)

    clk_core_enable(parent = pll1_d8_307p2)
    ...
    enable_count++ (on pmua_clk)

And so on. When the clk_enable(dma_clk) completes, we have these enable counts:
dma_clk: 1
pmua_clk: 1
pll1_d8_307p2: 1
pll1_d8: 1
pll1: 1? (I don't recall)

The -EPROBE_DEFER causes the devm_clk_get_optional_enabled() for dma_clk to get undone. That means clk_disable_unprepare() gets called on dma_clk. Let's just focus on clk_disable().

clk_disable(dma_clk)
clk_core_disable_lock(dma_clk)
(takes clk_enable lock) clk_core_disable()
--enable_count becomes 0 (on dma_clk) (disables dma_clk) clk_core_disable(core->parent = pmua_aclk)

clk_core_disable(pmua_aclk)
--enable_count becomes 0 (on pmua_clk) (disables pmua_clk) clk_core_dissable(core->parent = pll1_d8_307p2)

clk_core_disable(pll1_d8_307p2)

Quoted 8 lines
    --enable_count becomes 0 (on pll1_d8_307p2)
    (disables pll1_d8_307p2)
    clk_core_dissable(core->parent = pll1_d8)

clk_core_disable(pll1_d8\)
--enable_count becomes 0 (on pll1)
(disables pll1_d8)
BOOM

Yeah, I got the reason that pll1_d8 is disabled, but I don't still understand why it matters: pll1_d8 is a simple factor gate, though being parent of various peripheral clocks, it's okay to enable it again later if some peripherals decide to use it or one of its child, isn't it?

Quoted 8 lines

I could come up with several scenarios where disabling the clock really causes problems,

1. Some essential SoC components are actually supplied by pll1_d8 or one of its children, but isn't described in devicetree or the driver, thus disabling pll1_d8 leads to an SoC hang. We should mark the precise clock that being essential as critcal, instead of setting pll1_d8 as critical to work around the problem.

I second Haylen's suggestion here, instead of marking pll1_d8 as critical, we should find out which is the precise clock, or if turns out pll1_d8 must be provided for some essential SoC/CPU/or Bus, then fine by me

Quoted 8 lines

2. There're bugs in our clock driver, thus it fails to bring pll1_d8 (or maybe also its children) back to a sound state. If so we should fix the driver.

Unless you could confirm pll1_d8 (not its child) really supplies some essential SoC components, I don't think simply marking pll1_d8 as critical is the correct solution.

right

Quoted 3 lines

And, I don't even know what "non-functioning system" behaves like. Could you please provide more information, like soC behaviours or dmesg when disabling pll1_d8 causes problems? Thanks.

It could be likely the system just hang without any output.. maybe bus hang or something like that.. It would be great to poke vendor to get info from high topology level..

Quoted 9 lines
Quoted 4 lines

I hope this is clear.

-Alex

Regards,
Haylen Chu

Quoted 1 line
Signature · 1 line
Yixun Lan (dlan)
author
#5 lore raw
In reply to Haylen Chu
Quoted 1 line · Haylen Chu

On Sat, Jun 07, 2025 at 09:46:03PM -0500, Alex Elder wrote:

I respond below. I'm leaving all the context for now.

Quoted 117 lines
Quoted 108 lines · Yixun Lan
Quoted 6 lines

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

I will give you a full explanation of what I observed, below.

Quoted 11 lines
Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper

No, that is not the issue. The reset is never deasserted.

Quoted 2 lines

order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

The problem is with the pll1_d8 clock. That clock is enabled successfully. However the reset isn't ready, so the clock gets disabled, and its parent (and other ancestors) also get disabled while recovering from that.

I'll give you a high-level summary, then will lay out a ton of detail.

In the DMA driver probe function, several initial things happen and then, a clock is requested (enabled):
<&syscon_apmu CLK_DMA>
That succeeds.

Next, a reset is requested:
<&syscon_apmu RESET_DMA>
But that fails, because the reset driver probe function hasn't been called yet. The request gets -EPROBE_DEFER as its result, and the DMA driver starts unwinding everything so that it can be probed again later. Dropping the clock reference results in parent clocks dropping references. And because pll1_div8 initially had a reference count of 0 (despite being on), dropping this single reference means it gets disabled. Then we're stuck.

Here is how the DMA clock is supplied (at boot time):

pll1 -> pll1_d8 -> pll1_d8_307p2 -> pmua_aclk -> dma_clk

pll1 and pll1_d8 are enabled by the boot loader, but at this time the drivers for various hardware that require them aren't "getting" and enabling them (yet).

devm_clk_get_optional_enabled() causes clk_prepare_enable() to be called on the target clock (pll1_d8). That simply calls clk_prepare() and clk_enable(). Let's focus on the latter.
clk_enable(dma_clk)
clk_core_enable_lock()

So now the clock enable lock is held. The target clock's enable_count for pll1_d8 is 0.

clk_core_enable(dma_clk)
clk_core_enable(parent = pmua_aclk)
...
enable_count++ (on dma_clk)

The parent gets enabled (I'm fairly certain pmua_clk's enable_count is also 0).

   clk_core_enable(pmua_aclk)
     clk_core_enable(parent = pll1_d8_307p2)
     ...
     enable_count++ (on pmua_clk)

And so on. When the clk_enable(dma_clk) completes, we have these enable counts:

   dma_clk:		1
   pmua_clk:		1
   pll1_d8_307p2:	1
   pll1_d8:		1
   pll1:			1? (I don't recall)

The -EPROBE_DEFER causes the devm_clk_get_optional_enabled() for dma_clk to get undone. That means clk_disable_unprepare() gets called on dma_clk. Let's just focus on clk_disable().

   clk_disable(dma_clk)
     clk_core_disable_lock(dma_clk)
       (takes clk_enable lock)
       clk_core_disable()
         --enable_count becomes 0 (on dma_clk)
         (disables dma_clk)
         clk_core_disable(core->parent = pmua_aclk)

   clk_core_disable(pmua_aclk)
     --enable_count becomes 0 (on pmua_clk)
     (disables pmua_clk)
     clk_core_dissable(core->parent = pll1_d8_307p2)

   clk_core_disable(pll1_d8_307p2)
Quoted 8 lines
     --enable_count becomes 0 (on pll1_d8_307p2)
     (disables pll1_d8_307p2)
     clk_core_dissable(core->parent = pll1_d8)

   clk_core_disable(pll1_d8\)
     --enable_count becomes 0 (on pll1)
     (disables pll1_d8)
     BOOM
Quoted 4 lines

Yeah, I got the reason that pll1_d8 is disabled, but I don't still understand why it matters: pll1_d8 is a simple factor gate, though being parent of various peripheral clocks, it's okay to enable it again later if some peripherals decide to use it or one of its child, isn't it?

When it gets disabled, the system becomes non-functional. What that means is that everything stops, no more output, and even when I enabled KDB it did not drop into KDB. *Something* depends on it, but there is no driver that properly enables the clock (yet). This means--for now--it seems to be a critical clock.

Quoted 6 lines

I could come up with several scenarios where disabling the clock really causes problems,

1. Some essential SoC components are actually supplied by pll1_d8 or one of its children, but isn't described in devicetree or the driver, thus disabling pll1_d8 leads to an SoC hang. We should mark the

This is what I believe is happening. So my fix marks the one clock as critical in the driver. I would not want to mark it critical in DT.

Quoted 2 lines

precise clock that being essential as critcal, instead of setting pll1_d8 as critical to work around the problem.

I provided the chain of clocks leading to the dma_clk. Disabling the dma_clk did not cause harm; disabling pmua_aclk did not cause harm; disabling pll1_d8_307p2 did not cause harm. Only when pll1_d8 was disabled did the machine become unusable.

Quoted 3 lines

2. There're bugs in our clock driver, thus it fails to bring pll1_d8 (or maybe also its children) back to a sound state. If so we should fix the driver.

No, I found that pll1_d8 had an enable count of 1 after dma_clk was enabled. And then the set of disables that resulted from the -EPROBE_DEFER discovered its enable count was zero, and therefore disabled pll1_d8 (after dma_clk, pmua_aclk, and pll1_d8_307p2 were disabled). I do not suspect the clock *driver* is at fault.

Quoted 3 lines

Unless you could confirm pll1_d8 (not its child) really supplies some essential SoC components, I don't think simply marking pll1_d8 as critical is the correct solution.

I did confirm this. The child gets disabled before the parent in clk_core_disable().

Quoted 3 lines

And, I don't even know what "non-functioning system" behaves like. Could you please provide more information, like soC behaviours or dmesg when disabling pll1_d8 causes problems? Thanks.

Maybe you could, as an experiment, pretend <&syscon_apmu CLK_DMA> is a clock for something and get it during probe, using devm_clk_get_optional_enabled(). Then just return -EPROBE_DEFER after that, and I think you'll reproduce the issue. In fact, you might hit the issue more quickly if you used CLK_PLL1_D8.

-Alex

Quoted 74 lines
Quoted 3 lines

I hope this is clear.

-Alex

Regards,
Haylen Chu

Quoted 67 lines
Quoted 66 lines
Quoted 65 lines

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
   drivers/clk/spacemit/ccu-k1.c  |  3 ++-
   drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
   2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
   CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
   CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +13 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
   	}									\
   }
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
   #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
   			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
   #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
   			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2
#6 lore raw
Quoted 136 lines · Alex Elder
Quoted 1 line · Haylen Chu

On Sat, Jun 07, 2025 at 09:46:03PM -0500, Alex Elder wrote:

I respond below. I'm leaving all the context for now.

Quoted 117 lines
Quoted 108 lines · Yixun Lan
Quoted 6 lines

Hi Alex,

Quoted 2 lines · Alex Elder

The pll1_d8 clock is enabled by the boot loader, and is ultimately a parent for numerous clocks. Guodong Xu was recently testing DMA,

~~~~~~~~~this is still vague, numerous isn't equal to critical

I will give you a full explanation of what I observed, below.

Quoted 11 lines
Quoted 6 lines

adding a reset property, and discovered that the needed reset was not yet ready during initial probe. It dropped its clock reference, which dropped parent references, and along the way it dropped the sole reference to pll1_d8 (from its prior clk_get()). Clock pll1_d8 got disabled, which resulted in a non-functioning system.

So, I'm trying to understand the problem, and would like to evaluate if the "critical" flag is necessary..

It occurs to me, the DMA driver should request and enable clock first, then request and issue a reset, it probably could be solved by proper

No, that is not the issue. The reset is never deasserted.

Quoted 2 lines

order? so what's the real problem here? is DMA or reset? dropped the clock? or does driver fail to request a reset before clock is ready?

The problem is with the pll1_d8 clock. That clock is enabled successfully. However the reset isn't ready, so the clock gets disabled, and its parent (and other ancestors) also get disabled while recovering from that.

I'll give you a high-level summary, then will lay out a ton of detail.

In the DMA driver probe function, several initial things happen and then, a clock is requested (enabled):
<&syscon_apmu CLK_DMA>
That succeeds.

Next, a reset is requested:
<&syscon_apmu RESET_DMA>
But that fails, because the reset driver probe function hasn't been called yet. The request gets -EPROBE_DEFER as its result, and the DMA driver starts unwinding everything so that it can be probed again later. Dropping the clock reference results in parent clocks dropping references. And because pll1_div8 initially had a reference count of 0 (despite being on), dropping this single reference means it gets disabled. Then we're stuck.

Here is how the DMA clock is supplied (at boot time):

pll1 -> pll1_d8 -> pll1_d8_307p2 -> pmua_aclk -> dma_clk

pll1 and pll1_d8 are enabled by the boot loader, but at this time the drivers for various hardware that require them aren't "getting" and enabling them (yet).

devm_clk_get_optional_enabled() causes clk_prepare_enable() to be called on the target clock (pll1_d8). That simply calls clk_prepare() and clk_enable(). Let's focus on the latter.
clk_enable(dma_clk)
clk_core_enable_lock()

So now the clock enable lock is held. The target clock's enable_count for pll1_d8 is 0.

clk_core_enable(dma_clk)
clk_core_enable(parent = pmua_aclk)
...
enable_count++ (on dma_clk)

The parent gets enabled (I'm fairly certain pmua_clk's enable_count is also 0).

   clk_core_enable(pmua_aclk)
     clk_core_enable(parent = pll1_d8_307p2)
     ...
     enable_count++ (on pmua_clk)

And so on. When the clk_enable(dma_clk) completes, we have these enable counts:

   dma_clk:		1
   pmua_clk:		1
   pll1_d8_307p2:	1
   pll1_d8:		1
   pll1:			1? (I don't recall)

The -EPROBE_DEFER causes the devm_clk_get_optional_enabled() for dma_clk to get undone. That means clk_disable_unprepare() gets called on dma_clk. Let's just focus on clk_disable().

   clk_disable(dma_clk)
     clk_core_disable_lock(dma_clk)
       (takes clk_enable lock)
       clk_core_disable()
         --enable_count becomes 0 (on dma_clk)
         (disables dma_clk)
         clk_core_disable(core->parent = pmua_aclk)

   clk_core_disable(pmua_aclk)
     --enable_count becomes 0 (on pmua_clk)
     (disables pmua_clk)
     clk_core_dissable(core->parent = pll1_d8_307p2)

   clk_core_disable(pll1_d8_307p2)
Quoted 8 lines
     --enable_count becomes 0 (on pll1_d8_307p2)
     (disables pll1_d8_307p2)
     clk_core_dissable(core->parent = pll1_d8)

   clk_core_disable(pll1_d8\)
     --enable_count becomes 0 (on pll1)
     (disables pll1_d8)
     BOOM
Quoted 4 lines

Yeah, I got the reason that pll1_d8 is disabled, but I don't still understand why it matters: pll1_d8 is a simple factor gate, though being parent of various peripheral clocks, it's okay to enable it again later if some peripherals decide to use it or one of its child, isn't it?

When it gets disabled, the system becomes non-functional. What that means is that everything stops, no more output, and even when I enabled KDB it did not drop into KDB. *Something* depends on it, but there is no driver that properly enables the clock (yet). This means--for now--it seems to be a critical clock.

Quoted 3 lines

I could come up with several scenarios where disabling the clock really causes problems,

Quoted 7 lines
Quoted 3 lines

1. Some essential SoC components are actually supplied by pll1_d8 or one of its children, but isn't described in devicetree or the driver, thus disabling pll1_d8 leads to an SoC hang. We should mark the

This is what I believe is happening. So my fix marks the one clock as critical in the driver. I would not want to mark it critical in DT.

Okay. Then please make it more explicit in the commit message, "pll1_d8 seems to supply critical SoC components" describes the situation more precisely than "Clock pll1_d8 got disabled, which resulted in a non-functioning system".

Quoted 7 lines
Quoted 2 lines

precise clock that being essential as critcal, instead of setting pll1_d8 as critical to work around the problem.

I provided the chain of clocks leading to the dma_clk. Disabling the dma_clk did not cause harm; disabling pmua_aclk did not cause harm; disabling pll1_d8_307p2 did not cause harm. Only when pll1_d8 was disabled did the machine become unusable.

I don't think this is an evidence strong enough to prove pll1_d8 itself is critical.

pll1_d8 supplies not only pll1_d8_307p2 and its children, but also pll1_d16_153p6, pll1_d24_102p4 and many more. It's totally possible that not pll1_d8 but actually pll1_d16_153p6 or pll1_d24_102p4 is critical for SoC operation: in a normal functioning system with a working UART, these two clocks are always enabled since they (indirectly) supply UART bus and func clocks, hidding the problem.

In your case, when DMA driver reverts the enable operation, the UART driver don't seem to be probed yet (or enable count of pll1_d8 won't decrease to zero). Disabling the parent may cause an SoC hang as well if pll1_d16_153p6 or pll1_d24_102p4 is critcal in fact.

Quoted 9 lines
Quoted 3 lines

2. There're bugs in our clock driver, thus it fails to bring pll1_d8 (or maybe also its children) back to a sound state. If so we should fix the driver.

No, I found that pll1_d8 had an enable count of 1 after dma_clk was enabled. And then the set of disables that resulted from the -EPROBE_DEFER discovered its enable count was zero, and therefore disabled pll1_d8 (after dma_clk, pmua_aclk, and pll1_d8_307p2 were disabled). I do not suspect the clock *driver* is at fault.

A correct enable count doesn't mean the hardware is configured correctly.

Quoted 11 lines
Quoted 3 lines

Unless you could confirm pll1_d8 (not its child) really supplies some essential SoC components, I don't think simply marking pll1_d8 as critical is the correct solution.

I did confirm this. The child gets disabled before the parent in clk_core_disable().

Quoted 3 lines

And, I don't even know what "non-functioning system" behaves like. Could you please provide more information, like soC behaviours or dmesg when disabling pll1_d8 causes problems? Thanks.

Quoted 7 lines

Maybe you could, as an experiment, pretend <&syscon_apmu CLK_DMA> is a clock for something and get it during probe, using devm_clk_get_optional_enabled(). Then just return -EPROBE_DEFER after that, and I think you'll reproduce the issue. In fact, you might hit the issue more quickly if you used CLK_PLL1_D8.

-Alex

Thanks,
Haylen Chu

Quoted 75 lines
Quoted 74 lines
Quoted 3 lines

I hope this is clear.

-Alex

Regards,
Haylen Chu

Quoted 67 lines
Quoted 66 lines
Quoted 65 lines

Mark that clock critical so it doesn't get turned off in this case. We might be able to turn this flag off someday, but for now it resolves the problem Guodong encountered.

Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to be supplied for a CCU_FACTOR_GATE clock.

Fixes 1b72c59db0add ("clk: spacemit: Add clock support for SpacemiT K1 SoC")
---
   drivers/clk/spacemit/ccu-k1.c  |  3 ++-
   drivers/clk/spacemit/ccu_mix.h | 21 +++++++++++++--------
   2 files changed, 15 insertions(+), 9 deletions(-)
drivers/clk/spacemit/ccu-k1.c +2 -1
index cdde37a052353..df65009a07bb1 100644
@@ -170,7 +170,8 @@ CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4,
   CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
-CCU_FACTOR_GATE_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1);
+CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
+		CLK_IS_CRITICAL);
   CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
   CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
drivers/clk/spacemit/ccu_mix.h +13 -8
index 51d19f5d6aacb..668c8139339e1 100644
@@ -101,16 +101,21 @@ static struct ccu_mix _name = {							\
   	}									\
   }
+#define CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, _flags)					\
+struct ccu_mix _name = {							\
+	.gate	= CCU_GATE_INIT(_mask_gate),					\
+	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
+	.common = {								\
+		.reg_ctrl	= _reg_ctrl,					\
+		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, _flags)	\
+	}									\
+}
+
   #define CCU_FACTOR_GATE_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
   			       _mul)						\
-static struct ccu_mix _name = {							\
-	.gate	= CCU_GATE_INIT(_mask_gate),					\
-	.factor	= CCU_FACTOR_INIT(_div, _mul),					\
-	.common = {								\
-		.reg_ctrl	= _reg_ctrl,					\
-		CCU_MIX_INITHW(_name, _parent, spacemit_ccu_factor_gate_ops, 0)	\
-	}									\
-}
+	CCU_FACTOR_GATE_FLAGS_DEFINE(_name, _parent, _reg_ctrl, _mask_gate, _div,	\
+			       _mul, 0)
   #define CCU_MUX_GATE_DEFINE(_name, _parents, _reg_ctrl, _shift, _width,		\
   			    _mask_gate, _flags)					\
Signature · 1 line
2.45.2
#7 lore raw
In reply to Alex Elder
kernel test robot noticed the following build warnings:

Hi Alex,

kernel test robot noticed the following build warnings:

[auto build test WARNING on linus/master]
[also build test WARNING on next-20250606]
[cannot apply to v6.15]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Alex-Elder/clk-spacemit-mark-K1-pll1_d8-as-critical/20250608-042952
base:   linus/master
patch link:    https://lore.kernel.org/r/20250607202759.4180579-1-elder%40riscstar.com
patch subject: [PATCH] clk: spacemit: mark K1 pll1_d8 as critical
config: csky-randconfig-r111-20250608 (https://download.01.org/0day-ci/archive/20250609/[email protected]/config)
compiler: csky-linux-gcc (GCC) 15.1.0
reproduce: (https://download.01.org/0day-ci/archive/20250609/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

sparse warnings: (new ones prefixed by >>)

>> drivers/clk/spacemit/ccu-k1.c:168:1: sparse: sparse: symbol 'pll1_d3' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:170:1: sparse: sparse: symbol 'pll1_d5' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:172:1: sparse: sparse: symbol 'pll1_d7' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:175:1: sparse: sparse: symbol 'pll1_d11_223p4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:176:1: sparse: sparse: symbol 'pll1_d13_189' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:177:1: sparse: sparse: symbol 'pll1_d23_106p8' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:178:1: sparse: sparse: symbol 'pll1_d64_38p4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:179:1: sparse: sparse: symbol 'pll1_aud_245p7' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:180:1: sparse: sparse: symbol 'pll1_aud_24p5' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:182:1: sparse: sparse: symbol 'pll2_d1' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:183:1: sparse: sparse: symbol 'pll2_d2' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:184:1: sparse: sparse: symbol 'pll2_d3' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:185:1: sparse: sparse: symbol 'pll2_d4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:186:1: sparse: sparse: symbol 'pll2_d5' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:187:1: sparse: sparse: symbol 'pll2_d6' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:188:1: sparse: sparse: symbol 'pll2_d7' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:189:1: sparse: sparse: symbol 'pll2_d8' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:191:1: sparse: sparse: symbol 'pll3_d1' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:192:1: sparse: sparse: symbol 'pll3_d2' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:193:1: sparse: sparse: symbol 'pll3_d3' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:194:1: sparse: sparse: symbol 'pll3_d4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:195:1: sparse: sparse: symbol 'pll3_d5' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:196:1: sparse: sparse: symbol 'pll3_d6' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:197:1: sparse: sparse: symbol 'pll3_d7' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:198:1: sparse: sparse: symbol 'pll3_d8' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:214:1: sparse: sparse: symbol 'pll1_d24_102p4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:215:1: sparse: sparse: symbol 'pll1_d48_51p2' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:216:1: sparse: sparse: symbol 'pll1_d48_51p2_ap' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:217:1: sparse: sparse: symbol 'pll1_m3d128_57p6' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:218:1: sparse: sparse: symbol 'pll1_d96_25p6' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:219:1: sparse: sparse: symbol 'pll1_d192_12p8' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:220:1: sparse: sparse: symbol 'pll1_d192_12p8_wdt' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:221:1: sparse: sparse: symbol 'pll1_d384_6p4' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:228:1: sparse: sparse: symbol 'pll1_d12_204p8' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:231:1: sparse: sparse: symbol 'pll1_d10_245p76' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:234:1: sparse: sparse: symbol 'pll1_d52_47p26' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:235:1: sparse: sparse: symbol 'pll1_d78_31p5' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:247:1: sparse: sparse: symbol 'i2s_sysclk' was not declared. Should it be static?
>> drivers/clk/spacemit/ccu-k1.c:248:1: sparse: sparse: symbol 'i2s_bclk' was not declared. Should it be static?

vim +/pll1_d3 +168 drivers/clk/spacemit/ccu-k1.c

1b72c59db0add8 Haylen Chu 2025-04-16  159  
1b72c59db0add8 Haylen Chu 2025-04-16  160  CCU_PLL_DEFINE(pll1, pll1_rate_tbl, APBS_PLL1_SWCR1, APBS_PLL1_SWCR3, MPMU_POSR, POSR_PLL1_LOCK,
1b72c59db0add8 Haylen Chu 2025-04-16  161  	       CLK_SET_RATE_GATE);
1b72c59db0add8 Haylen Chu 2025-04-16  162  CCU_PLL_DEFINE(pll2, pll2_rate_tbl, APBS_PLL2_SWCR1, APBS_PLL2_SWCR3, MPMU_POSR, POSR_PLL2_LOCK,
1b72c59db0add8 Haylen Chu 2025-04-16  163  	       CLK_SET_RATE_GATE);
1b72c59db0add8 Haylen Chu 2025-04-16  164  CCU_PLL_DEFINE(pll3, pll3_rate_tbl, APBS_PLL3_SWCR1, APBS_PLL3_SWCR3, MPMU_POSR, POSR_PLL3_LOCK,
1b72c59db0add8 Haylen Chu 2025-04-16  165  	       CLK_SET_RATE_GATE);
1b72c59db0add8 Haylen Chu 2025-04-16  166  
1b72c59db0add8 Haylen Chu 2025-04-16  167  CCU_FACTOR_GATE_DEFINE(pll1_d2, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(1), 2, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @168  CCU_FACTOR_GATE_DEFINE(pll1_d3, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(2), 3, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  169  CCU_FACTOR_GATE_DEFINE(pll1_d4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(3), 4, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @170  CCU_FACTOR_GATE_DEFINE(pll1_d5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(4), 5, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  171  CCU_FACTOR_GATE_DEFINE(pll1_d6, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(5), 6, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @172  CCU_FACTOR_GATE_DEFINE(pll1_d7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(6), 7, 1);
5d0122955ef9fd Alex Elder 2025-06-07  173  CCU_FACTOR_GATE_FLAGS_DEFINE(pll1_d8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(7), 8, 1,
5d0122955ef9fd Alex Elder 2025-06-07  174  		CLK_IS_CRITICAL);
1b72c59db0add8 Haylen Chu 2025-04-16 @175  CCU_FACTOR_GATE_DEFINE(pll1_d11_223p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(15), 11, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @176  CCU_FACTOR_GATE_DEFINE(pll1_d13_189, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(16), 13, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @177  CCU_FACTOR_GATE_DEFINE(pll1_d23_106p8, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(20), 23, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @178  CCU_FACTOR_GATE_DEFINE(pll1_d64_38p4, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(0), 64, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @179  CCU_FACTOR_GATE_DEFINE(pll1_aud_245p7, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(10), 10, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @180  CCU_FACTOR_GATE_DEFINE(pll1_aud_24p5, CCU_PARENT_HW(pll1), APBS_PLL1_SWCR2, BIT(11), 100, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  181  
1b72c59db0add8 Haylen Chu 2025-04-16 @182  CCU_FACTOR_GATE_DEFINE(pll2_d1, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(0), 1, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @183  CCU_FACTOR_GATE_DEFINE(pll2_d2, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(1), 2, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @184  CCU_FACTOR_GATE_DEFINE(pll2_d3, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(2), 3, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @185  CCU_FACTOR_GATE_DEFINE(pll2_d4, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(3), 4, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @186  CCU_FACTOR_GATE_DEFINE(pll2_d5, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(4), 5, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @187  CCU_FACTOR_GATE_DEFINE(pll2_d6, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(5), 6, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @188  CCU_FACTOR_GATE_DEFINE(pll2_d7, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(6), 7, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @189  CCU_FACTOR_GATE_DEFINE(pll2_d8, CCU_PARENT_HW(pll2), APBS_PLL2_SWCR2, BIT(7), 8, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  190  
1b72c59db0add8 Haylen Chu 2025-04-16 @191  CCU_FACTOR_GATE_DEFINE(pll3_d1, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(0), 1, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @192  CCU_FACTOR_GATE_DEFINE(pll3_d2, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(1), 2, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @193  CCU_FACTOR_GATE_DEFINE(pll3_d3, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(2), 3, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @194  CCU_FACTOR_GATE_DEFINE(pll3_d4, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(3), 4, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @195  CCU_FACTOR_GATE_DEFINE(pll3_d5, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(4), 5, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @196  CCU_FACTOR_GATE_DEFINE(pll3_d6, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(5), 6, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @197  CCU_FACTOR_GATE_DEFINE(pll3_d7, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(6), 7, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @198  CCU_FACTOR_GATE_DEFINE(pll3_d8, CCU_PARENT_HW(pll3), APBS_PLL3_SWCR2, BIT(7), 8, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  199  
1b72c59db0add8 Haylen Chu 2025-04-16  200  CCU_FACTOR_DEFINE(pll3_20, CCU_PARENT_HW(pll3_d8), 20, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  201  CCU_FACTOR_DEFINE(pll3_40, CCU_PARENT_HW(pll3_d8), 10, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  202  CCU_FACTOR_DEFINE(pll3_80, CCU_PARENT_HW(pll3_d8), 5, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  203  
1b72c59db0add8 Haylen Chu 2025-04-16  204  /* APBS clocks end */
1b72c59db0add8 Haylen Chu 2025-04-16  205  
1b72c59db0add8 Haylen Chu 2025-04-16  206  /* MPMU clocks start */
1b72c59db0add8 Haylen Chu 2025-04-16  207  CCU_GATE_DEFINE(pll1_d8_307p2, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(13), 0);
1b72c59db0add8 Haylen Chu 2025-04-16  208  
1b72c59db0add8 Haylen Chu 2025-04-16  209  CCU_FACTOR_DEFINE(pll1_d32_76p8, CCU_PARENT_HW(pll1_d8_307p2), 4, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  210  
1b72c59db0add8 Haylen Chu 2025-04-16  211  CCU_FACTOR_DEFINE(pll1_d40_61p44, CCU_PARENT_HW(pll1_d8_307p2), 5, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  212  
1b72c59db0add8 Haylen Chu 2025-04-16  213  CCU_FACTOR_DEFINE(pll1_d16_153p6, CCU_PARENT_HW(pll1_d8), 2, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @214  CCU_FACTOR_GATE_DEFINE(pll1_d24_102p4, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(12), 3, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @215  CCU_FACTOR_GATE_DEFINE(pll1_d48_51p2, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(7), 6, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @216  CCU_FACTOR_GATE_DEFINE(pll1_d48_51p2_ap, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(11), 6, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @217  CCU_FACTOR_GATE_DEFINE(pll1_m3d128_57p6, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(8), 16, 3);
1b72c59db0add8 Haylen Chu 2025-04-16 @218  CCU_FACTOR_GATE_DEFINE(pll1_d96_25p6, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(4), 12, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @219  CCU_FACTOR_GATE_DEFINE(pll1_d192_12p8, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(3), 24, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @220  CCU_FACTOR_GATE_DEFINE(pll1_d192_12p8_wdt, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(19), 24, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @221  CCU_FACTOR_GATE_DEFINE(pll1_d384_6p4, CCU_PARENT_HW(pll1_d8), MPMU_ACGR, BIT(2), 48, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  222  
1b72c59db0add8 Haylen Chu 2025-04-16  223  CCU_FACTOR_DEFINE(pll1_d768_3p2, CCU_PARENT_HW(pll1_d384_6p4), 2, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  224  CCU_FACTOR_DEFINE(pll1_d1536_1p6, CCU_PARENT_HW(pll1_d384_6p4), 4, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  225  CCU_FACTOR_DEFINE(pll1_d3072_0p8, CCU_PARENT_HW(pll1_d384_6p4), 8, 1);
1b72c59db0add8 Haylen Chu 2025-04-16  226  
1b72c59db0add8 Haylen Chu 2025-04-16  227  CCU_GATE_DEFINE(pll1_d6_409p6, CCU_PARENT_HW(pll1_d6), MPMU_ACGR, BIT(0), 0);

1b72c59db0add8 Haylen Chu 2025-04-16 @228 CCU_FACTOR_GATE_DEFINE(pll1_d12_204p8, CCU_PARENT_HW(pll1_d6), MPMU_ACGR, BIT(5), 2, 1); 1b72c59db0add8 Haylen Chu 2025-04-16 229
1b72c59db0add8 Haylen Chu 2025-04-16 230 CCU_GATE_DEFINE(pll1_d5_491p52, CCU_PARENT_HW(pll1_d5), MPMU_ACGR, BIT(21), 0); 1b72c59db0add8 Haylen Chu 2025-04-16 @231 CCU_FACTOR_GATE_DEFINE(pll1_d10_245p76, CCU_PARENT_HW(pll1_d5), MPMU_ACGR, BIT(18), 2, 1); 1b72c59db0add8 Haylen Chu 2025-04-16 232

1b72c59db0add8 Haylen Chu 2025-04-16  233  CCU_GATE_DEFINE(pll1_d4_614p4, CCU_PARENT_HW(pll1_d4), MPMU_ACGR, BIT(15), 0);
1b72c59db0add8 Haylen Chu 2025-04-16 @234  CCU_FACTOR_GATE_DEFINE(pll1_d52_47p26, CCU_PARENT_HW(pll1_d4), MPMU_ACGR, BIT(10), 13, 1);
1b72c59db0add8 Haylen Chu 2025-04-16 @235  CCU_FACTOR_GATE_DEFINE(pll1_d78_31p5, CCU_PARENT_HW(pll1_d4), MPMU_ACGR, BIT(6), 39, 2);
1b72c59db0add8 Haylen Chu 2025-04-16  236  
1b72c59db0add8 Haylen Chu 2025-04-16  237  CCU_GATE_DEFINE(pll1_d3_819p2, CCU_PARENT_HW(pll1_d3), MPMU_ACGR, BIT(14), 0);
1b72c59db0add8 Haylen Chu 2025-04-16  238  
1b72c59db0add8 Haylen Chu 2025-04-16  239  CCU_GATE_DEFINE(pll1_d2_1228p8, CCU_PARENT_HW(pll1_d2), MPMU_ACGR, BIT(16), 0);
1b72c59db0add8 Haylen Chu 2025-04-16  240  
1b72c59db0add8 Haylen Chu 2025-04-16  241  CCU_GATE_DEFINE(slow_uart, CCU_PARENT_NAME(osc), MPMU_ACGR, BIT(1), CLK_IGNORE_UNUSED);
1b72c59db0add8 Haylen Chu 2025-04-16  242  CCU_DDN_DEFINE(slow_uart1_14p74, pll1_d16_153p6, MPMU_SUCCR, 16, 13, 0, 13, 0);
1b72c59db0add8 Haylen Chu 2025-04-16  243  CCU_DDN_DEFINE(slow_uart2_48, pll1_d4_614p4, MPMU_SUCCR_1, 16, 13, 0, 13, 0);
1b72c59db0add8 Haylen Chu 2025-04-16  244  
1b72c59db0add8 Haylen Chu 2025-04-16  245  CCU_GATE_DEFINE(wdt_clk, CCU_PARENT_HW(pll1_d96_25p6), MPMU_WDTPCR, BIT(1), 0);
1b72c59db0add8 Haylen Chu 2025-04-16  246  

1b72c59db0add8 Haylen Chu 2025-04-16 @247 CCU_FACTOR_GATE_DEFINE(i2s_sysclk, CCU_PARENT_HW(pll1_d16_153p6), MPMU_ISCCR, BIT(31), 50, 1); 1b72c59db0add8 Haylen Chu 2025-04-16 @248 CCU_FACTOR_GATE_DEFINE(i2s_bclk, CCU_PARENT_HW(i2s_sysclk), MPMU_ISCCR, BIT(29), 1, 1); 1b72c59db0add8 Haylen Chu 2025-04-16 249

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki