ASoC: SOF: ipc4-pcm: Enable delay reporting for ChainDMA streams
Subsystems (3)
Peter Ujfalusi
maintainerPATCH 1/1 ASoC: SOF: ipc4-pcm: Enable delay reporting for ChainDMA streams
All streams (currently) which is configured to use ChainDMA can only work on Link/host DMA pairs where the link side position can be access via host registers (like HDA on CAVS 2.5 platforms).
Since the firmware does not provide time_info for ChainDMA, unlike for HDA stream, the kernel should calculate the start and end offsets that is needed for the delay calculation.
With this small change we can report accurate delays when the stream is configured to use ChainDMA.
--- sound/soc/sof/ipc4-pcm.c | 49 ++++++++++++++++++++++++++++++++--- sound/soc/sof/ipc4-topology.c | 6 ++--- sound/soc/sof/ipc4-topology.h | 1 + 3 files changed, 49 insertions(+), 7 deletions(-)
sound/soc/sof/ipc4-pcm.c +45 -4
@@ -409,9 +409,33 @@ static int sof_ipc4_trigger_pipelines(struct snd_soc_component *component,* If use_chain_dma attribute is set we proceed to chained DMA * trigger function that handles the rest for the substream. */ -if (pipeline->use_chain_dma) -return sof_ipc4_chain_dma_trigger (sdev, spcm, substream->stream, - pipeline_list, state, cmd); +if (pipeline->use_chain_dma) { +struct sof_ipc4_timestamp_info *time_info; + + time_info =sof_ipc4_sps_to_time_info (&spcm->stream[substream->stream]); + + ret =sof_ipc4_chain_dma_trigger (sdev, spcm, substream->stream, + pipeline_list, state, cmd); +if (ret || !time_info) +return ret; + +if (state ==SOF_IPC4_PIPE_PAUSED ) { +/* +* Record the DAI position for delay reporting +* To handle multiple pause/resume/xrun we need to add +* the positions to simulate how the firmware behaves +*/ +u64 pos =snd_sof_pcm_get_dai_frame_counter (sdev, component, + substream); + + time_info->stream_end_offset += pos; + }else if (state ==SOF_IPC4_PIPE_RESET ) { +/* Reset the end offset as the stream is stopped */ + time_info->stream_end_offset =0 ; + } + +return 0 ; + }/* allocate memory for the pipeline data */ trigger_list = kzalloc(struct_size(trigger_list, pipeline_instance_ids,
@@ -928,8 +952,24 @@ static int sof_ipc4_get_stream_start_offset(struct snd_sof_dev *sdev,if (!host_copier || !dai_copier)return -EINVAL ; -if (host_copier->data.gtw_cfg.node_id ==SOF_IPC4_INVALID_NODE_ID ) +if (host_copier->data.gtw_cfg.node_id ==SOF_IPC4_INVALID_NODE_ID ) {return -EINVAL ; + }else if (host_copier->data.gtw_cfg.node_id ==SOF_IPC4_CHAIN_DMA_NODE_ID ) { +/* +* While the firmware does not supports time_info reporting for +* streams using ChainDMA, it is granted that ChainDMA can only +* be used on Host+Link pairs where the link position is +* accessible from the host side. +* +* Enable delay calculation in case of ChainDMA via host +* accessible registers. +* +* The ChainDMA uses 2x 1ms ping-pong buffer, dai side starts +* when 1ms data is available +*/ + time_info->stream_start_offset = substream->runtime->rate /MSEC_PER_SEC ; + goto out; + } node_index =SOF_IPC4_NODE_INDEX (host_copier->data.gtw_cfg.node_id); offset = offsetof(struct sof_ipc4_fw_registers , pipeline_regs) + node_index *sizeof (ppl_reg);
@@ -947,6 +987,7 @@ static int sof_ipc4_get_stream_start_offset(struct snd_sof_dev *sdev, time_info->stream_end_offset = ppl_reg.stream_end_offset;do_div (time_info->stream_end_offset, dai_sample_size); +out:/* * Calculate the wrap boundary need to be used for delay calculation * The host counter is in bytes, it will wrap earlier than the frames
sound/soc/sof/ipc4-topology.c +3 -3
@@ -1873,10 +1873,10 @@ sof_ipc4_prepare_copier_module(struct snd_sof_widget *swidget, pipeline->msg.extension |=SOF_IPC4_GLB_EXT_CHAIN_DMA_FIFO_SIZE (fifo_size);/* -* Chain DMA does not support stream timestamping, set node_id to invalid -* to skip the code in sof_ipc4_get_stream_start_offset(). +* Chain DMA does not support stream timestamping, but it +* can use the host side registers for delay calculation. */ - copier_data->gtw_cfg.node_id =SOF_IPC4_INVALID_NODE_ID ; + copier_data->gtw_cfg.node_id =SOF_IPC4_CHAIN_DMA_NODE_ID ;return 0 ; }
sound/soc/sof/ipc4-topology.h +1 -0
@@ -58,6 +58,7 @@#define SOF_IPC4_DMA_DEVICE_MAX_COUNT 16 +#define SOF_IPC4_CHAIN_DMA_NODE_ID 0x7fffffff#define SOF_IPC4_INVALID_NODE_ID 0xffffffff/* FW requires minimum 2ms DMA buffer size */
Signature · 1 line
2.49.0
Mark Brown
maintainerQuoted 9 lines · Peter Ujfalusi
All streams (currently) which is configured to use ChainDMA can only work on Link/host DMA pairs where the link side position can be access via host registers (like HDA on CAVS 2.5 platforms).
Since the firmware does not provide
time_infofor ChainDMA, unlike for HDA stream, the kernel should calculate the start and end offsets that is needed for the delay calculation.[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/1] ASoC: SOF: ipc4-pcm: Enable delay reporting for ChainDMA streams
commit: a1d203d390e04798ccc1c3c06019cd4411885d6d
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark