reset: brcmstb: Enable reset drivers for ARCH_BCM2835
PATCH v2 1/1 reset: brcmstb: Enable reset drivers for ARCH_BCM2835
The BRCMSTB and BRCMSTB_RESCAL reset drivers are also used in the BCM2712, AKA the RPi5. The RPi platforms have typically used the ARCH_BCM2835, and the PCIe support for this SoC can use this config which depends on these drivers so enable building them when just that arch option is enabled to ensure the platform works as expected.
---
v2: Update the defaults to add ARCH_BCM2835
This allows 6.16 to boot on the rpi5 when just using ARCH_BCM2835, which is what Fedora uses, otherwise the boot stops due to deps.
drivers/reset/Kconfig | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/reset/Kconfig +5 -5
@@ -51,8 +51,8 @@ config RESET_BERLIN config RESET_BRCMSTB tristate "Broadcom STB reset controller" - depends on ARCH_BRCMSTB || COMPILE_TEST - default ARCH_BRCMSTB + depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST + default ARCH_BRCMSTB || ARCH_BCM2835 help This enables the reset controller driver for Broadcom STB SoCs using a SUN_TOP_CTRL_SW_INIT style controller.
@@ -60,11 +60,11 @@ config RESET_BRCMSTB config RESET_BRCMSTB_RESCAL tristate "Broadcom STB RESCAL reset controller" depends on HAS_IOMEM - depends on ARCH_BRCMSTB || COMPILE_TEST - default ARCH_BRCMSTB + depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST + default ARCH_BRCMSTB || ARCH_BCM2835 help This enables the RESCAL reset controller for SATA, PCIe0, or PCIe1 on - BCM7216. + BCM7216 or the BCM2712. config RESET_EYEQ bool "Mobileye EyeQ reset controller"
Signature · 1 line
2.50.0
Quoted 9 lines · Peter Robinson
The BRCMSTB and
BRCMSTB_RESCALreset drivers are also used in the BCM2712, AKA the RPi5. The RPi platforms have typically used theARCH_BCM2835, and the PCIe support for this SoC can use this config which depends on these drivers so enable building them when just that arch option is enabled to ensure the platform works as expected.Signed-off-by Peter Robinson <[email protected]>
Signature · 1 line
Florian
Quoted 8 lines · Peter Robinson
The BRCMSTB and
BRCMSTB_RESCALreset drivers are also used in the BCM2712, AKA the RPi5. The RPi platforms have typically used theARCH_BCM2835, and the PCIe support for this SoC can use this config which depends on these drivers so enable building them when just that arch option is enabled to ensure the platform works as expected.
Quoted 7 lines
Signed-off-by Peter Robinson <[email protected]>---
v2: Update the defaults to add
ARCH_BCM2835This allows 6.16 to boot on the rpi5 when just using
ARCH_BCM2835, which is what Fedora uses, otherwise the boot stops due to deps.
Applied to reset/next, thanks!
[1/1] reset: brcmstb: Enable reset drivers for ARCH_BCM2835
https://git.pengutronix.de/cgit/pza/linux/commit/?id=1d99f92f71b6
regards
Philipp