Skip to contentSkip to conversation

allwinner: a523: Add power controllers

PATCH Superseded Chen-Yu Tsai 3 participants 10 messages Jul 9, 2025 – Jul 10, 2025

Subsystems (3)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Chen-Yu Tsai

author maintainer
#0 lore raw

v2 cover allwinner: a523: Add power controllers

From: Chen-Yu Tsai <[email protected]>

Hi folks,

This is v2 of my A523 power controllers series.

Changes since v1:
- Re-order compatible string entries
- Fix name of header file to match compatible string
- Link to v1:
https://lore.kernel.org/all/[email protected]/

This series adds the power controllers found in the Allwinner A523 family of SoCs. There are two power controllers. One is the same type as those found in the D1 SoC, just with a different number of valid power domains. The second is (I assume) a unit based on ARM's PCK-600 power controller. Some of the registers and values match up, but there are extra registers for delay controls in the PCK-600's reserved register range.

Patch 1 adds new compatible string entries for both of these controllers.

Patch 2 adds support for the A523 PPU to the existing D1 PPU driver.

Patch 3 adds a new driver of the PCK-600 unit in the A523 SoC.

Patch 4 adds device nodes for both of these controllers.

Please have a look. The power controllers are critical for enabling more peripherals, such as display output, camera input, video codecs, the NPU, and a second DWMAC-compatible ethernet interface.

Thanks
ChenYu

Chen-Yu Tsai (4):
dt-bindings: power: Add A523 PPU and PCK600 power controllers
pmdomain: sunxi: sun20i-ppu: add A523 support
pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power
controller
arm64: dts: allwinner: a523: Add power controller device nodes

 .../power/allwinner,sun20i-d1-ppu.yaml        |   4 +-
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi |  18 ++
 drivers/pmdomain/sunxi/Kconfig                |   8 +
 drivers/pmdomain/sunxi/Makefile               |   1 +
 drivers/pmdomain/sunxi/sun20i-ppu.c           |  17 ++
 drivers/pmdomain/sunxi/sun55i-pck600.c        | 225 ++++++++++++++++++
 .../power/allwinner,sun55i-a523-pck-600.h     |  15 ++
 .../power/allwinner,sun55i-a523-ppu.h         |  12 +
 8 files changed, 299 insertions(+), 1 deletion(-)
 create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-pck-600.h
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-ppu.h
Signature · 1 line
2.39.5
author maintainer
#1 lore raw

PATCH v2 1/4 dt-bindings: power: Add A523 PPU and PCK600 power controllers

From: Chen-Yu Tsai <[email protected]>

The A523 PPU is likely the same kind of hardware seen on previous SoCs.

The A523 PCK600, as the name suggests, is likely a customized version of ARM's PCK-600 power controller. Comparing the BSP driver against ARM's PPU datasheet shows that the basic registers line up, but Allwinner's hardware has some additional delay controls in the reserved register range. As such it is likely not fully compatible with the standard ARM version.

Document A523 PPU and PCK600 compatibles.

Also reorder the compatible string entries so they are grouped and ordered by family first, then by SoC model.

---
Changes since v1:
- Re-order compatible string entries
- Fix name of header file to match compatible string

---
 .../bindings/power/allwinner,sun20i-d1-ppu.yaml   |  4 +++-
 .../power/allwinner,sun55i-a523-pck-600.h         | 15 +++++++++++++++
 .../dt-bindings/power/allwinner,sun55i-a523-ppu.h | 12 ++++++++++++
 3 files changed, 30 insertions(+), 1 deletion(-)
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-pck-600.h
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-ppu.h
Documentation/devicetree/bindings/power/allwinner,sun20i-d1-ppu.yaml +3 -1
index f578be6a3bc8..a28e75a9cb6a 100644
@@ -16,8 +16,10 @@ description:
 properties:
   compatible:
     enum:
-      - allwinner,sun20i-d1-ppu
       - allwinner,sun8i-v853-ppu
+      - allwinner,sun20i-d1-ppu
+      - allwinner,sun55i-a523-pck-600
+      - allwinner,sun55i-a523-ppu
 
   reg:
     maxItems: 1
include/dt-bindings/power/allwinner,sun55i-a523-pck-600.h new file +15 -0
new file mode 100644
index 000000000000..6b3d8ea7bb69
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DT_BINDINGS_POWER_SUN55I_A523_PCK600_H_
+#define _DT_BINDINGS_POWER_SUN55I_A523_PCK600_H_
+
+#define PD_VE			0
+#define PD_GPU			1
+#define PD_VI			2
+#define PD_VO0			3
+#define PD_VO1			4
+#define PD_DE			5
+#define PD_NAND			6
+#define PD_PCIE			7
+
+#endif /* _DT_BINDINGS_POWER_SUN55I_A523_PCK600_H_ */
include/dt-bindings/power/allwinner,sun55i-a523-ppu.h new file +12 -0
new file mode 100644
index 000000000000..bc9aba73c19a
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DT_BINDINGS_POWER_SUN55I_A523_PPU_H_
+#define _DT_BINDINGS_POWER_SUN55I_A523_PPU_H_
+
+#define PD_DSP			0
+#define PD_NPU			1
+#define PD_AUDIO		2
+#define PD_SRAM			3
+#define PD_RISCV		4
+
+#endif /* _DT_BINDINGS_POWER_SUN55I_A523_PPU_H_ */
Signature · 1 line
2.39.5
author maintainer
#3 lore raw

PATCH v2 2/4 pmdomain: sunxi: sun20i-ppu: add A523 support

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

A523 has a PPU like the one in the Allwinner D1 SoC.

Add a compatible entry and a list of power domain names for it.

---
 drivers/pmdomain/sunxi/sun20i-ppu.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
drivers/pmdomain/sunxi/sun20i-ppu.c +17 -0
index 9f002748d224..b65876a68cc1 100644
@@ -193,6 +193,19 @@ static const struct sun20i_ppu_desc sun8i_v853_ppu_desc = {
 	.num_domains	= ARRAY_SIZE(sun8i_v853_ppu_pd_names),
 };
 
+static const char *const sun55i_a523_ppu_pd_names[] = {
+	"DSP",
+	"NPU",
+	"AUDIO",
+	"SRAM",
+	"RISCV",
+};
+
+static const struct sun20i_ppu_desc sun55i_a523_ppu_desc = {
+	.names		= sun55i_a523_ppu_pd_names,
+	.num_domains	= ARRAY_SIZE(sun55i_a523_ppu_pd_names),
+};
+
 static const struct of_device_id sun20i_ppu_of_match[] = {
 	{
 		.compatible	= "allwinner,sun20i-d1-ppu",
@@ -202,6 +215,10 @@ static const struct of_device_id sun20i_ppu_of_match[] = {
 		.compatible	= "allwinner,sun8i-v853-ppu",
 		.data		= &sun8i_v853_ppu_desc,
 	},
+	{
+		.compatible	= "allwinner,sun55i-a523-ppu",
+		.data		= &sun55i_a523_ppu_desc,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, sun20i_ppu_of_match);
Signature · 1 line
2.39.5
author maintainer
#4 lore raw

PATCH v2 3/4 pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power controller

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner A523 family has a second power controller, named PCK-600 in the datasheets and BSP. It is likely based on ARM's PCK-600 hardware block, with some additional delay controls. The only documentation for this hardware is the BSP driver. The standard registers defined in ARM's Power Policy Unit Architecture Specification line up. Some extra delay controls are found in the reserved range of registers.

Add a driver for this power controller. Delay control register values and power domain names are from the BSP driver.

---
 drivers/pmdomain/sunxi/Kconfig         |   8 +
 drivers/pmdomain/sunxi/Makefile        |   1 +
 drivers/pmdomain/sunxi/sun55i-pck600.c | 225 +++++++++++++++++++++++++
 3 files changed, 234 insertions(+)
 create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c
drivers/pmdomain/sunxi/Kconfig +8 -0
index 43eecb3ea981..3e2b77cd9a2b 100644
@@ -18,3 +18,11 @@ config SUN50I_H6_PRCM_PPU
 	  Say y to enable the Allwinner H6/H616 PRCM power domain driver.
 	  This is required to enable the Mali GPU in the H616 SoC, it is
 	  optional for the H6.
+
+config SUN55I_PCK600
+	bool "Allwinner A523 PCK-600 power domain driver"
+	depends on PM
+	select PM_GENERIC_DOMAINS
+	help
+	  Say y to enable the PCK-600 power domain driver. This saves power
+	  when certain peripherals, such as the video engine, are idle.
drivers/pmdomain/sunxi/Makefile +1 -0
index c1343e123759..e344b232fc9f 100644
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_SUN20I_PPU)		+= sun20i-ppu.o
 obj-$(CONFIG_SUN50I_H6_PRCM_PPU)	+= sun50i-h6-prcm-ppu.o
+obj-$(CONFIG_SUN55I_PCK600)		+= sun55i-pck600.o
drivers/pmdomain/sunxi/sun55i-pck600.c new file +225 -0

225 lines not on this page · raw message

Signature · 1 line
2.39.5
author maintainer
#8 lore raw

PATCH v2 4/4 arm64: dts: allwinner: a523: Add power controller device nodes

In reply to Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The A523 SoC family has two power controllers, one based on the existing PPU, and one newer one based on ARM's PCK-600.

Add device nodes for both of them.

---
 arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi +18 -0
index cf0bc39aab04..dd6fa22f960f 100644
@@ -7,6 +7,8 @@
 #include <dt-bindings/clock/sun55i-a523-r-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-r-ccu.h>
+#include <dt-bindings/power/allwinner,sun55i-a523-ppu.h>
+#include <dt-bindings/power/allwinner,sun55i-a523-pck600.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -576,6 +578,14 @@ mdio0: mdio {
 			};
 		};
 
+		ppu: power-controller@7001400 {
+			compatible = "allwinner,sun55i-a523-ppu";
+			reg = <0x07001400 0x400>;
+			clocks = <&r_ccu CLK_BUS_R_PPU1>;
+			resets = <&r_ccu RST_BUS_R_PPU1>;
+			#power-domain-cells = <1>;
+		};
+
 		r_ccu: clock-controller@7010000 {
 			compatible = "allwinner,sun55i-a523-r-ccu";
 			reg = <0x7010000 0x250>;
@@ -622,6 +632,14 @@ r_i2c_pins: r-i2c-pins {
 			};
 		};
 
+		pck600: power-controller@7060000 {
+			compatible = "allwinner,sun55i-a523-pck-600";
+			reg = <0x07060000 0x8000>;
+			clocks = <&r_ccu CLK_BUS_R_PPU0>;
+			resets = <&r_ccu RST_BUS_R_PPU0>;
+			#power-domain-cells = <1>;
+		};
+
 		r_i2c0: i2c@7081400 {
 			compatible = "allwinner,sun55i-a523-i2c",
 				     "allwinner,sun8i-v536-i2c",
Signature · 1 line
2.39.5
#9 lore raw
In reply to Chen-Yu Tsai
Quoted 59 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Hi folks,

This is v2 of my A523 power controllers series.

Changes since v1:
- Re-order compatible string entries
- Fix name of header file to match compatible string
- Link to v1:
https://lore.kernel.org/all/[email protected]/

This series adds the power controllers found in the Allwinner A523 family of SoCs. There are two power controllers. One is the same type as those found in the D1 SoC, just with a different number of valid power domains. The second is (I assume) a unit based on ARM's PCK-600 power controller. Some of the registers and values match up, but there are extra registers for delay controls in the PCK-600's reserved register range.

Patch 1 adds new compatible string entries for both of these controllers.

Patch 2 adds support for the A523 PPU to the existing D1 PPU driver.

Patch 3 adds a new driver of the PCK-600 unit in the A523 SoC.

Patch 4 adds device nodes for both of these controllers.

Please have a look. The power controllers are critical for enabling more peripherals, such as display output, camera input, video codecs, the NPU, and a second DWMAC-compatible ethernet interface.

Thanks
ChenYu

Chen-Yu Tsai (4):
dt-bindings: power: Add A523 PPU and PCK600 power controllers
pmdomain: sunxi: sun20i-ppu: add A523 support
pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power
controller
arm64: dts: allwinner: a523: Add power controller device nodes

 .../power/allwinner,sun20i-d1-ppu.yaml        |   4 +-
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi |  18 ++
 drivers/pmdomain/sunxi/Kconfig                |   8 +
 drivers/pmdomain/sunxi/Makefile               |   1 +
 drivers/pmdomain/sunxi/sun20i-ppu.c           |  17 ++
 drivers/pmdomain/sunxi/sun55i-pck600.c        | 225 ++++++++++++++++++
 .../power/allwinner,sun55i-a523-pck-600.h     |  15 ++
 .../power/allwinner,sun55i-a523-ppu.h         |  12 +
 8 files changed, 299 insertions(+), 1 deletion(-)
 create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-pck-600.h
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-ppu.h
Quoted 5 lines

--
2.39.5

My bot found new DTB warnings on the .dts files added or changed in this series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date:

  pip3 install dtschema --upgrade

This patch series was applied (using b4) to base:
Base: attempting to guess base-commit...
Base: tags/next-20250709 (exact match)

If this is not the correct base, please add 'base-commit' tag (or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/allwinner/' for [email protected]:

In file included from arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts:8:
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi:11:10: fatal error: dt-bindings/power/allwinner,sun55i-a523-pck600.h: No such file or directory
11 | #include <dt-bindings/power/allwinner,sun55i-a523-pck600.h>

      |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

compilation terminated.
make[3]: *** [scripts/Makefile.dtbs:131: arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dtb] Error 1
make[2]: *** [scripts/Makefile.build:554: arch/arm64/boot/dts/allwinner] Error 2
make[2]: Target 'arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dtb' not remade because of errors.
make[1]: *** [/home/rob/proj/linux-dt-testing/Makefile:1478: allwinner/sun55i-t527-orangepi-4a.dtb] Error 2
In file included from arch/arm64/boot/dts/allwinner/sun55i-h728-x96qpro+.dts:6:
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi:11:10: fatal error: dt-bindings/power/allwinner,sun55i-a523-pck600.h: No such file or directory
11 | #include <dt-bindings/power/allwinner,sun55i-a523-pck600.h>

      |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

compilation terminated.
make[3]: *** [scripts/Makefile.dtbs:131: arch/arm64/boot/dts/allwinner/sun55i-h728-x96qpro+.dtb] Error 1
make[2]: *** [scripts/Makefile.build:554: arch/arm64/boot/dts/allwinner] Error 2
make[2]: Target 'arch/arm64/boot/dts/allwinner/sun55i-h728-x96qpro+.dtb' not remade because of errors.
make[1]: *** [/home/rob/proj/linux-dt-testing/Makefile:1478: allwinner/sun55i-h728-x96qpro+.dtb] Error 2
In file included from arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts:6:
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi:11:10: fatal error: dt-bindings/power/allwinner,sun55i-a523-pck600.h: No such file or directory
11 | #include <dt-bindings/power/allwinner,sun55i-a523-pck600.h>

      |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

compilation terminated.
make[3]: *** [scripts/Makefile.dtbs:131: arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dtb] Error 1
make[2]: *** [scripts/Makefile.build:554: arch/arm64/boot/dts/allwinner] Error 2
make[2]: Target 'arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dtb' not remade because of errors.
make[1]: *** [/home/rob/proj/linux-dt-testing/Makefile:1478: allwinner/sun55i-a527-cubie-a5e.dtb] Error 2
In file included from arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts:6:
arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi:11:10: fatal error: dt-bindings/power/allwinner,sun55i-a523-pck600.h: No such file or directory
11 | #include <dt-bindings/power/allwinner,sun55i-a523-pck600.h>

      |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

compilation terminated.
make[3]: *** [scripts/Makefile.dtbs:131: arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dtb] Error 1 make[2]: *** [scripts/Makefile.build:554: arch/arm64/boot/dts/allwinner] Error 2 make[2]: Target 'arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dtb' not remade because of errors. make[1]: *** [/home/rob/proj/linux-dt-testing/Makefile:1478: allwinner/sun55i-t527-avaota-a1.dtb] Error 2
make: *** [Makefile:248: __sub-make] Error 2
make: Target 'allwinner/sun50i-h616-bigtreetech-cb1-manta.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-libretech-all-h3-it.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-tanix-tx6.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h616-x96-mate.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-orangepi-pc2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-libretech-all-h3-cc.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h700-anbernic-rg35xx-plus.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-orangepi-zero-plus2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinephone-1.1.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h618-orangepi-zero2w.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h618-longanpi-3h.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-pine-h64.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h616-orangepi-zero2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-olinuxino-emmc.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-sopine-baseboard.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-emlid-neutis-n5-devboard.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-beelink-gs1.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h616-bigtreetech-pi.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h700-anbernic-rg35xx-2024.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a100-allwinner-perf1.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-orangepi-win.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinephone-1.2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h700-anbernic-rg35xx-h.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pine64.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinetab-early-adopter.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-nanopi-neo-plus2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-bananapi-m2-plus-v1.2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h618-yuzukihd-chameleon.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-orangepi-3.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-amarula-relic.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pine64-lts.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-bananapi-m2-plus.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-bananapi-m64.dtb' not remade because of errors.
make: Target 'allwinner/sun55i-t527-orangepi-4a.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-orangepi-zero-plus.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-olinuxino.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinebook.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-oceanic-5205-5inmfd.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pine64-plus.dtb' not remade because of errors.
make: Target 'allwinner/sun55i-h728-x96qpro+.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-teres-i.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinetab.dtb' not remade because of errors.
make: Target 'allwinner/sun55i-a527-cubie-a5e.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h700-anbernic-rg35xx-sp.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-pine-h64-model-b.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-orangepi-prime.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-nanopi-a64.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h618-transpeed-8k618-t.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-libretech-all-h5-cc.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a64-pinephone-1.0.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-orangepi-lite2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-tanix-tx6-mini.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h618-orangepi-zero3.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-nanopi-r1s-h5.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h64-remix-mini-pc.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-a133-liontron-h-a133l.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h5-nanopi-neo2.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h313-tanix-tx1.dtb' not remade because of errors.
make: Target 'allwinner/sun55i-t527-avaota-a1.dtb' not remade because of errors.
make: Target 'allwinner/sun50i-h6-orangepi-one-plus.dtb' not remade because of errors.

#5 lore raw

Re: [PATCH v2 3/4] pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power controller

In reply to Chen-Yu Tsai

Hi Chen-Yu,

thanks for posting this! This is a quick first view, haven't compared against the BSP bits yet....

Quoted 25 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner A523 family has a second power controller, named PCK-600 in the datasheets and BSP. It is likely based on ARM's PCK-600 hardware block, with some additional delay controls. The only documentation for this hardware is the BSP driver. The standard registers defined in ARM's Power Policy Unit Architecture Specification line up. Some extra delay controls are found in the reserved range of registers.

Add a driver for this power controller. Delay control register values and power domain names are from the BSP driver.

---
  drivers/pmdomain/sunxi/Kconfig         |   8 +
  drivers/pmdomain/sunxi/Makefile        |   1 +
  drivers/pmdomain/sunxi/sun55i-pck600.c | 225 +++++++++++++++++++++++++
  3 files changed, 234 insertions(+)

create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c

drivers/pmdomain/sunxi/Kconfig +0 -0
index 43eecb3ea981..3e2b77cd9a2b 100644

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 23

Quoted 6 lines
drivers/pmdomain/sunxi/Kconfig +3 -0
@@ -18,3 +18,11 @@ config SUN50I_H6_PRCM_PPU
  	  Say y to enable the Allwinner H6/H616 PRCM power domain driver.
  	  This is required to enable the Mali GPU in the H616 SoC, it is
  	  optional for the H6.
+
+config SUN55I_PCK600
+	bool "Allwinner A523 PCK-600 power domain driver"

Any particular reason this is not tristate? The driver advertises itself as a platform driver module?

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 28

Quoted 5 lines
drivers/pmdomain/sunxi/Kconfig +5 -0
+	depends on PM
+	select PM_GENERIC_DOMAINS
+	help
+	  Say y to enable the PCK-600 power domain driver. This saves power
+	  when certain peripherals, such as the video engine, are idle.

If I understand correctly, this driver is *required* to make use of those peripherals, and the video engine is not even the most prominent user. So regardless of the reset state of the power domain, I think the wording should be changed, to make sure distributions activate this option. At the moment it sounds highly optional. I wonder if we should use "default y if ARCH_SUNXI" even.

Quoted 15 lines
drivers/pmdomain/sunxi/Makefile +1 -0
index c1343e123759..e344b232fc9f 100644
@@ -1,3 +1,4 @@
  # SPDX-License-Identifier: GPL-2.0-only
  obj-$(CONFIG_SUN20I_PPU)		+= sun20i-ppu.o
  obj-$(CONFIG_SUN50I_H6_PRCM_PPU)	+= sun50i-h6-prcm-ppu.o
+obj-$(CONFIG_SUN55I_PCK600)		+= sun55i-pck600.o
drivers/pmdomain/sunxi/sun55i-pck600.c new file +0 -0
new file mode 100644
index 000000000000..7248f6113665

drivers/pmdomain/sunxi/sun55i-pck600.c line 3

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Allwinner PCK-600 power domain support

Can you please mention here that this device is based on the Arm PCK-600 IP, as done in the commit message. And say that this is a minimal implementaton, just supporting the off/on states.

Maybe also mention the relevant documentation: the "ARM CoreLink PCK‑600 Power Control Kit" TRM and the "Arm Power Policy Unit" architecture specification (DEN0051E).

Quoted 13 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +13 -0
+ *
+ * Copyright (c) 2025 Chen-Yu Tsai <[email protected]>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/container_of.h>
+#include <linux/device.h>
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>

drivers/pmdomain/sunxi/sun55i-pck600.c line 26

Quoted 10 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +10 -0
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/string_choices.h>
+
+#define PPU_PWPR    0x0
+#define PPU_PWSR    0x8
+#define	PPU_DCDR0   0x170

white space issue?

drivers/pmdomain/sunxi/sun55i-pck600.c line 29

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
+#define PPU_DCDR1   0x174
+
+#define PPU_PWSR_PWR_STATUS	GENMASK(3, 0)

Would just PPU_PWR_STATUS be a better name, since it's used by both the PWPR and PWSR registers?

Quoted 6 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +6 -0
+#define PPU_POWER_MODE_ON	0x8
+#define PPU_POWER_MODE_OFF	0x0
+
+#define PPU_REG_SIZE	0x1000
+
+struct sunxi_pck600_desc {

drivers/pmdomain/sunxi/sun55i-pck600.c line 45

Quoted 10 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +10 -0
+	const char * const *pd_names;
+	unsigned int num_domains;
+	u32 logic_power_switch0_delay_offset;
+	u32 logic_power_switch1_delay_offset;
+	u32 off2on_delay_offset;
+	u32 device_ctrl0_delay;
+	u32 device_ctrl1_delay;
+	u32 logic_power_switch0_delay;
+	u32 logic_power_switch1_delay;
+	u32 off2on_delay;

Is there any indication that those parameters are different between different SoCs? I appreciate the idea of making this future-proof, but this might be a bit premature, if all SoCs use the same values?

Quoted 18 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +18 -0
+};
+
+struct sunxi_pck600_pd {
+	struct generic_pm_domain genpd;
+	struct sunxi_pck600 *pck;
+	void __iomem *base;
+};
+
+struct sunxi_pck600 {
+	struct device *dev;
+	struct genpd_onecell_data genpd_data;
+	struct sunxi_pck600_pd pds[];
+};
+
+#define to_sunxi_pd(gpd) container_of(gpd, struct sunxi_pck600_pd, genpd)
+
+static int sunxi_pck600_pd_set_power(struct sunxi_pck600_pd *pd, bool on)
+{

drivers/pmdomain/sunxi/sun55i-pck600.c line 73

Quoted 10 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +10 -0
+	struct sunxi_pck600 *pck = pd->pck;
+	struct generic_pm_domain *genpd = &pd->genpd;
+	int ret;
+	u32 val, reg;
+
+	val = on ? PPU_POWER_MODE_ON : PPU_POWER_MODE_OFF;
+
+	reg = readl(pd->base + PPU_PWPR);
+	FIELD_MODIFY(PPU_PWSR_PWR_STATUS, &reg, val);
+	writel(reg, pd->base + PPU_PWPR);

Don't we need a lock here, or is this covered by the power domain framework?

Cheers,
Andre

Quoted 152 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +152 -0
+
+	/* push write out to hardware */
+	reg = readl(pd->base + PPU_PWPR);
+
+	ret = readl_poll_timeout_atomic(pd->base + PPU_PWSR, reg,
+					FIELD_GET(PPU_PWSR_PWR_STATUS, reg) == val,
+					0, 10000);
+	if (ret)
+		dev_err(pck->dev, "failed to turn domain \"%s\" %s: %d\n",
+			genpd->name, str_on_off(on), ret);
+
+	return ret;
+}
+
+static int sunxi_pck600_power_on(struct generic_pm_domain *domain)
+{
+	struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+	return sunxi_pck600_pd_set_power(pd, true);
+}
+
+static int sunxi_pck600_power_off(struct generic_pm_domain *domain)
+{
+	struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+	return sunxi_pck600_pd_set_power(pd, false);
+}
+
+static void sunxi_pck600_pd_setup(struct sunxi_pck600_pd *pd,
+				  const struct sunxi_pck600_desc *desc)
+{
+	writel(desc->device_ctrl0_delay, pd->base + PPU_DCDR0);
+	writel(desc->device_ctrl1_delay, pd->base + PPU_DCDR1);
+	writel(desc->logic_power_switch0_delay,
+	       pd->base + desc->logic_power_switch0_delay_offset);
+	writel(desc->logic_power_switch1_delay,
+	       pd->base + desc->logic_power_switch1_delay_offset);
+	writel(desc->off2on_delay, pd->base + desc->off2on_delay_offset);
+}
+
+static int sunxi_pck600_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct sunxi_pck600_desc *desc;
+	struct genpd_onecell_data *genpds;
+	struct sunxi_pck600 *pck;
+	struct reset_control *rst;
+	struct clk *clk;
+	void __iomem *base;
+	int i, ret;
+
+	desc = of_device_get_match_data(dev);
+
+	pck = devm_kzalloc(dev, struct_size(pck, pds, desc->num_domains), GFP_KERNEL);
+	if (!pck)
+		return -ENOMEM;
+
+	pck->dev = &pdev->dev;
+	platform_set_drvdata(pdev, pck);
+
+	genpds = &pck->genpd_data;
+	genpds->num_domains = desc->num_domains;
+	genpds->domains = devm_kcalloc(dev, desc->num_domains,
+				       sizeof(*genpds->domains), GFP_KERNEL);
+	if (!genpds->domains)
+		return -ENOMEM;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	rst = devm_reset_control_get_exclusive_released(dev, NULL);
+	if (IS_ERR(rst))
+		return dev_err_probe(dev, PTR_ERR(rst), "failed to get reset control\n");
+
+	clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(clk))
+		return dev_err_probe(dev, PTR_ERR(clk), "failed to get clock\n");
+
+	for (i = 0; i < desc->num_domains; i++) {
+		struct sunxi_pck600_pd *pd = &pck->pds[i];
+
+		pd->genpd.name = desc->pd_names[i];
+		pd->genpd.power_off = sunxi_pck600_power_off;
+		pd->genpd.power_on = sunxi_pck600_power_on;
+		pd->base = base + PPU_REG_SIZE * i;
+
+		sunxi_pck600_pd_setup(pd, desc);
+		ret = pm_genpd_init(&pd->genpd, NULL, false);
+		if (ret) {
+			dev_err_probe(dev, ret, "failed to initialize power domain\n");
+			goto err_remove_pds;
+		}
+
+		genpds->domains[i] = &pd->genpd;
+	}
+
+	ret = of_genpd_add_provider_onecell(dev_of_node(dev), genpds);
+	if (ret) {
+		dev_err_probe(dev, ret, "failed to add PD provider\n");
+		goto err_remove_pds;
+	}
+
+	return 0;
+
+err_remove_pds:
+	for (i--; i >= 0; i--)
+		pm_genpd_remove(genpds->domains[i]);
+
+	return ret;
+}
+
+static const char * const sun55i_a523_pck600_pd_names[] = {
+	"VE", "GPU", "VI", "VO0", "VO1", "DE", "NAND", "PCIE"
+};
+
+static const struct sunxi_pck600_desc sun55i_a523_pck600_desc = {
+	.pd_names = sun55i_a523_pck600_pd_names,
+	.num_domains = ARRAY_SIZE(sun55i_a523_pck600_pd_names),
+	.logic_power_switch0_delay_offset = 0xc00,
+	.logic_power_switch1_delay_offset = 0xc04,
+	.off2on_delay_offset = 0xc10,
+	.device_ctrl0_delay = 0xffffff,
+	.device_ctrl1_delay = 0xffff,
+	.logic_power_switch0_delay = 0x8080808,
+	.logic_power_switch1_delay = 0x808,
+	.off2on_delay = 0x8
+};
+
+static const struct of_device_id sunxi_pck600_of_match[] = {
+	{
+		.compatible	= "allwinner,sun55i-a523-pck-600",
+		.data		= &sun55i_a523_pck600_desc,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, sunxi_pck600_of_match);
+
+static struct platform_driver sunxi_pck600_driver = {
+	.probe = sunxi_pck600_probe,
+	.driver = {
+		.name   = "sunxi-pck-600",
+		.of_match_table = sunxi_pck600_of_match,
+		/* Power domains cannot be removed if in use. */
+		.suppress_bind_attrs = true,
+	},
+};
+module_platform_driver(sunxi_pck600_driver);
+
+MODULE_DESCRIPTION("Allwinner PCK-600 power domain driver");
+MODULE_AUTHOR("Chen-Yu Tsai <[email protected]>");
+MODULE_LICENSE("GPL");
author maintainer
#6 lore raw

Re: [PATCH v2 3/4] pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power controller

Quoted 27 lines · Andre Przywara

Hi Chen-Yu,

thanks for posting this! This is a quick first view, haven't compared against the BSP bits yet....

Quoted 20 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner A523 family has a second power controller, named PCK-600 in the datasheets and BSP. It is likely based on ARM's PCK-600 hardware block, with some additional delay controls. The only documentation for this hardware is the BSP driver. The standard registers defined in ARM's Power Policy Unit Architecture Specification line up. Some extra delay controls are found in the reserved range of registers.

Add a driver for this power controller. Delay control register values and power domain names are from the BSP driver.

---
  drivers/pmdomain/sunxi/Kconfig         |   8 +
  drivers/pmdomain/sunxi/Makefile        |   1 +
  drivers/pmdomain/sunxi/sun55i-pck600.c | 225 +++++++++++++++++++++++++
  3 files changed, 234 insertions(+)

create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c

Quoted 14 lines

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 23

Quoted 11 lines
drivers/pmdomain/sunxi/Kconfig +3 -0
index 43eecb3ea981..3e2b77cd9a2b 100644
@@ -18,3 +18,11 @@ config SUN50I_H6_PRCM_PPU
        Say y to enable the Allwinner H6/H616 PRCM power domain driver.
        This is required to enable the Mali GPU in the H616 SoC, it is
        optional for the H6.
+
+config SUN55I_PCK600
+     bool "Allwinner A523 PCK-600 power domain driver"

Any particular reason this is not tristate? The driver advertises itself as a platform driver module?

Cargo-culted from the D1 PPU driver. So, no particular reason.

Quoted 6 lines

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 28

Quoted 5 lines
drivers/pmdomain/sunxi/Kconfig +5 -0
+     depends on PM
+     select PM_GENERIC_DOMAINS
+     help
+       Say y to enable the PCK-600 power domain driver. This saves power
+       when certain peripherals, such as the video engine, are idle.
Quoted 6 lines

If I understand correctly, this driver is *required* to make use of those peripherals, and the video engine is not even the most prominent user. So regardless of the reset state of the power domain, I think the wording should be changed, to make sure distributions activate this option. At the moment it sounds highly optional. I wonder if we should use "default y if ARCH_SUNXI" even.

Makes sense. Though this was also cargo-culted from the D1 PPU. So I guess I should fix both.

Quoted 23 lines
Quoted 15 lines
drivers/pmdomain/sunxi/Makefile +1 -0
index c1343e123759..e344b232fc9f 100644
@@ -1,3 +1,4 @@
  # SPDX-License-Identifier: GPL-2.0-only
  obj-$(CONFIG_SUN20I_PPU)            += sun20i-ppu.o
  obj-$(CONFIG_SUN50I_H6_PRCM_PPU)    += sun50i-h6-prcm-ppu.o
+obj-$(CONFIG_SUN55I_PCK600)          += sun55i-pck600.o
drivers/pmdomain/sunxi/sun55i-pck600.c new file +0 -0
new file mode 100644
index 000000000000..7248f6113665

drivers/pmdomain/sunxi/sun55i-pck600.c line 3

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Allwinner PCK-600 power domain support

Can you please mention here that this device is based on the Arm PCK-600 IP, as done in the commit message. And say that this is a minimal implementaton, just supporting the off/on states.

Quoted 3 lines

Maybe also mention the relevant documentation: the "ARM CoreLink PCK‑600 Power Control Kit" TRM and the "Arm Power Policy Unit" architecture specification (DEN0051E).

Will do.

Quoted 45 lines
Quoted 13 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +13 -0
+ *
+ * Copyright (c) 2025 Chen-Yu Tsai <[email protected]>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/container_of.h>
+#include <linux/device.h>
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>

drivers/pmdomain/sunxi/sun55i-pck600.c line 26

Quoted 10 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +10 -0
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/string_choices.h>
+
+#define PPU_PWPR    0x0
+#define PPU_PWSR    0x8
+#define      PPU_DCDR0   0x170

white space issue?

drivers/pmdomain/sunxi/sun55i-pck600.c line 29

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
+#define PPU_DCDR1   0x174
+
+#define PPU_PWSR_PWR_STATUS  GENMASK(3, 0)

Would just PPU_PWR_STATUS be a better name, since it's used by both the PWPR and PWSR registers?

Quoted 12 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +12 -0
+#define PPU_POWER_MODE_ON    0x8
+#define PPU_POWER_MODE_OFF   0x0
+
+#define PPU_REG_SIZE 0x1000
+
+struct sunxi_pck600_desc {
+     const char * const *pd_names;
+     unsigned int num_domains;
+     u32 logic_power_switch0_delay_offset;
+     u32 logic_power_switch1_delay_offset;
+     u32 off2on_delay_offset;
+     u32 device_ctrl0_delay;
Quoted 8 lines

drivers/pmdomain/sunxi/sun55i-pck600.c line 45

Quoted 4 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +4 -0
+     u32 device_ctrl1_delay;
+     u32 logic_power_switch0_delay;
+     u32 logic_power_switch1_delay;
+     u32 off2on_delay;

Is there any indication that those parameters are different between different SoCs? I appreciate the idea of making this future-proof, but this might be a bit premature, if all SoCs use the same values?

It's hard to tell since the BSP driver only covers the A523. I'd just keep this the way it is, since it makes it easier to generalize this to cover PCK-600 in other platforms, if such a need ever presents itself.

Quoted 22 lines
Quoted 22 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +22 -0
+};
+
+struct sunxi_pck600_pd {
+     struct generic_pm_domain genpd;
+     struct sunxi_pck600 *pck;
+     void __iomem *base;
+};
+
+struct sunxi_pck600 {
+     struct device *dev;
+     struct genpd_onecell_data genpd_data;
+     struct sunxi_pck600_pd pds[];
+};
+
+#define to_sunxi_pd(gpd) container_of(gpd, struct sunxi_pck600_pd, genpd)
+
+static int sunxi_pck600_pd_set_power(struct sunxi_pck600_pd *pd, bool on)
+{
+     struct sunxi_pck600 *pck = pd->pck;
+     struct generic_pm_domain *genpd = &pd->genpd;
+     int ret;
+     u32 val, reg;
Quoted 8 lines

drivers/pmdomain/sunxi/sun55i-pck600.c line 73

Quoted 6 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +6 -0
+
+     val = on ? PPU_POWER_MODE_ON : PPU_POWER_MODE_OFF;
+
+     reg = readl(pd->base + PPU_PWPR);
+     FIELD_MODIFY(PPU_PWSR_PWR_STATUS, &reg, val);
+     writel(reg, pd->base + PPU_PWPR);

Don't we need a lock here, or is this covered by the power domain framework?

AFAICT genpd has a lock for each power domain. Since each power domain has its own set of registers, I think we're good here.

Thanks
ChenYu

Quoted 157 lines

Cheers,
Andre

Quoted 152 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +152 -0
+
+     /* push write out to hardware */
+     reg = readl(pd->base + PPU_PWPR);
+
+     ret = readl_poll_timeout_atomic(pd->base + PPU_PWSR, reg,
+                                     FIELD_GET(PPU_PWSR_PWR_STATUS, reg) == val,
+                                     0, 10000);
+     if (ret)
+             dev_err(pck->dev, "failed to turn domain \"%s\" %s: %d\n",
+                     genpd->name, str_on_off(on), ret);
+
+     return ret;
+}
+
+static int sunxi_pck600_power_on(struct generic_pm_domain *domain)
+{
+     struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+     return sunxi_pck600_pd_set_power(pd, true);
+}
+
+static int sunxi_pck600_power_off(struct generic_pm_domain *domain)
+{
+     struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+     return sunxi_pck600_pd_set_power(pd, false);
+}
+
+static void sunxi_pck600_pd_setup(struct sunxi_pck600_pd *pd,
+                               const struct sunxi_pck600_desc *desc)
+{
+     writel(desc->device_ctrl0_delay, pd->base + PPU_DCDR0);
+     writel(desc->device_ctrl1_delay, pd->base + PPU_DCDR1);
+     writel(desc->logic_power_switch0_delay,
+            pd->base + desc->logic_power_switch0_delay_offset);
+     writel(desc->logic_power_switch1_delay,
+            pd->base + desc->logic_power_switch1_delay_offset);
+     writel(desc->off2on_delay, pd->base + desc->off2on_delay_offset);
+}
+
+static int sunxi_pck600_probe(struct platform_device *pdev)
+{
+     struct device *dev = &pdev->dev;
+     const struct sunxi_pck600_desc *desc;
+     struct genpd_onecell_data *genpds;
+     struct sunxi_pck600 *pck;
+     struct reset_control *rst;
+     struct clk *clk;
+     void __iomem *base;
+     int i, ret;
+
+     desc = of_device_get_match_data(dev);
+
+     pck = devm_kzalloc(dev, struct_size(pck, pds, desc->num_domains), GFP_KERNEL);
+     if (!pck)
+             return -ENOMEM;
+
+     pck->dev = &pdev->dev;
+     platform_set_drvdata(pdev, pck);
+
+     genpds = &pck->genpd_data;
+     genpds->num_domains = desc->num_domains;
+     genpds->domains = devm_kcalloc(dev, desc->num_domains,
+                                    sizeof(*genpds->domains), GFP_KERNEL);
+     if (!genpds->domains)
+             return -ENOMEM;
+
+     base = devm_platform_ioremap_resource(pdev, 0);
+     if (IS_ERR(base))
+             return PTR_ERR(base);
+
+     rst = devm_reset_control_get_exclusive_released(dev, NULL);
+     if (IS_ERR(rst))
+             return dev_err_probe(dev, PTR_ERR(rst), "failed to get reset control\n");
+
+     clk = devm_clk_get_enabled(dev, NULL);
+     if (IS_ERR(clk))
+             return dev_err_probe(dev, PTR_ERR(clk), "failed to get clock\n");
+
+     for (i = 0; i < desc->num_domains; i++) {
+             struct sunxi_pck600_pd *pd = &pck->pds[i];
+
+             pd->genpd.name = desc->pd_names[i];
+             pd->genpd.power_off = sunxi_pck600_power_off;
+             pd->genpd.power_on = sunxi_pck600_power_on;
+             pd->base = base + PPU_REG_SIZE * i;
+
+             sunxi_pck600_pd_setup(pd, desc);
+             ret = pm_genpd_init(&pd->genpd, NULL, false);
+             if (ret) {
+                     dev_err_probe(dev, ret, "failed to initialize power domain\n");
+                     goto err_remove_pds;
+             }
+
+             genpds->domains[i] = &pd->genpd;
+     }
+
+     ret = of_genpd_add_provider_onecell(dev_of_node(dev), genpds);
+     if (ret) {
+             dev_err_probe(dev, ret, "failed to add PD provider\n");
+             goto err_remove_pds;
+     }
+
+     return 0;
+
+err_remove_pds:
+     for (i--; i >= 0; i--)
+             pm_genpd_remove(genpds->domains[i]);
+
+     return ret;
+}
+
+static const char * const sun55i_a523_pck600_pd_names[] = {
+     "VE", "GPU", "VI", "VO0", "VO1", "DE", "NAND", "PCIE"
+};
+
+static const struct sunxi_pck600_desc sun55i_a523_pck600_desc = {
+     .pd_names = sun55i_a523_pck600_pd_names,
+     .num_domains = ARRAY_SIZE(sun55i_a523_pck600_pd_names),
+     .logic_power_switch0_delay_offset = 0xc00,
+     .logic_power_switch1_delay_offset = 0xc04,
+     .off2on_delay_offset = 0xc10,
+     .device_ctrl0_delay = 0xffffff,
+     .device_ctrl1_delay = 0xffff,
+     .logic_power_switch0_delay = 0x8080808,
+     .logic_power_switch1_delay = 0x808,
+     .off2on_delay = 0x8
+};
+
+static const struct of_device_id sunxi_pck600_of_match[] = {
+     {
+             .compatible     = "allwinner,sun55i-a523-pck-600",
+             .data           = &sun55i_a523_pck600_desc,
+     },
+     {}
+};
+MODULE_DEVICE_TABLE(of, sunxi_pck600_of_match);
+
+static struct platform_driver sunxi_pck600_driver = {
+     .probe = sunxi_pck600_probe,
+     .driver = {
+             .name   = "sunxi-pck-600",
+             .of_match_table = sunxi_pck600_of_match,
+             /* Power domains cannot be removed if in use. */
+             .suppress_bind_attrs = true,
+     },
+};
+module_platform_driver(sunxi_pck600_driver);
+
+MODULE_DESCRIPTION("Allwinner PCK-600 power domain driver");
+MODULE_AUTHOR("Chen-Yu Tsai <[email protected]>");
+MODULE_LICENSE("GPL");
maintainer Reviewed-by on v2 1/4
#2 lore raw

Re: [PATCH v2 1/4] dt-bindings: power: Add A523 PPU and PCK600 power controllers

In reply to Chen-Yu Tsai
Quoted 23 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

The A523 PPU is likely the same kind of hardware seen on previous SoCs.

The A523 PCK600, as the name suggests, is likely a customized version of ARM's PCK-600 power controller. Comparing the BSP driver against ARM's PPU datasheet shows that the basic registers line up, but Allwinner's hardware has some additional delay controls in the reserved register range. As such it is likely not fully compatible with the standard ARM version.

Document A523 PPU and PCK600 compatibles.

Also reorder the compatible string entries so they are grouped and ordered by family first, then by SoC model.

---
Changes since v1:
- Re-order compatible string entries
- Fix name of header file to match compatible string

Quoted 8 lines
---
 .../bindings/power/allwinner,sun20i-d1-ppu.yaml   |  4 +++-
 .../power/allwinner,sun55i-a523-pck-600.h         | 15 +++++++++++++++
 .../dt-bindings/power/allwinner,sun55i-a523-ppu.h | 12 ++++++++++++
 3 files changed, 30 insertions(+), 1 deletion(-)
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-pck-600.h
 create mode 100644 include/dt-bindings/power/allwinner,sun55i-a523-ppu.h
#7 lore raw

Re: [PATCH v2 3/4] pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power controller

In reply to Chen-Yu Tsai

Hi,

Quoted 144 lines · Chen-Yu Tsai
Quoted 27 lines · Andre Przywara

Hi Chen-Yu,

thanks for posting this! This is a quick first view, haven't compared against the BSP bits yet....

Quoted 20 lines · Chen-Yu Tsai

From: Chen-Yu Tsai <[email protected]>

Allwinner A523 family has a second power controller, named PCK-600 in the datasheets and BSP. It is likely based on ARM's PCK-600 hardware block, with some additional delay controls. The only documentation for this hardware is the BSP driver. The standard registers defined in ARM's Power Policy Unit Architecture Specification line up. Some extra delay controls are found in the reserved range of registers.

Add a driver for this power controller. Delay control register values and power domain names are from the BSP driver.

---
   drivers/pmdomain/sunxi/Kconfig         |   8 +
   drivers/pmdomain/sunxi/Makefile        |   1 +
   drivers/pmdomain/sunxi/sun55i-pck600.c | 225 +++++++++++++++++++++++++
   3 files changed, 234 insertions(+)

create mode 100644 drivers/pmdomain/sunxi/sun55i-pck600.c

Quoted 14 lines

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 23

Quoted 11 lines
drivers/pmdomain/sunxi/Kconfig +3 -0
index 43eecb3ea981..3e2b77cd9a2b 100644
@@ -18,3 +18,11 @@ config SUN50I_H6_PRCM_PPU
         Say y to enable the Allwinner H6/H616 PRCM power domain driver.
         This is required to enable the Mali GPU in the H616 SoC, it is
         optional for the H6.
+
+config SUN55I_PCK600
+     bool "Allwinner A523 PCK-600 power domain driver"

Any particular reason this is not tristate? The driver advertises itself as a platform driver module?

Cargo-culted from the D1 PPU driver. So, no particular reason.

Quoted 6 lines

drivers/pmdomain/sunxi/Kconfig config SUN50I_H6_PRCM_PPU · line 28

Quoted 5 lines
drivers/pmdomain/sunxi/Kconfig +5 -0
+     depends on PM
+     select PM_GENERIC_DOMAINS
+     help
+       Say y to enable the PCK-600 power domain driver. This saves power
+       when certain peripherals, such as the video engine, are idle.
Quoted 6 lines

If I understand correctly, this driver is *required* to make use of those peripherals, and the video engine is not even the most prominent user. So regardless of the reset state of the power domain, I think the wording should be changed, to make sure distributions activate this option. At the moment it sounds highly optional. I wonder if we should use "default y if ARCH_SUNXI" even.

Makes sense. Though this was also cargo-culted from the D1 PPU. So I guess I should fix both.

Quoted 23 lines
Quoted 15 lines
drivers/pmdomain/sunxi/Makefile +1 -0
index c1343e123759..e344b232fc9f 100644
@@ -1,3 +1,4 @@
   # SPDX-License-Identifier: GPL-2.0-only
   obj-$(CONFIG_SUN20I_PPU)            += sun20i-ppu.o
   obj-$(CONFIG_SUN50I_H6_PRCM_PPU)    += sun50i-h6-prcm-ppu.o
+obj-$(CONFIG_SUN55I_PCK600)          += sun55i-pck600.o
drivers/pmdomain/sunxi/sun55i-pck600.c new file +0 -0
new file mode 100644
index 000000000000..7248f6113665

drivers/pmdomain/sunxi/sun55i-pck600.c line 3

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Allwinner PCK-600 power domain support

Can you please mention here that this device is based on the Arm PCK-600 IP, as done in the commit message. And say that this is a minimal implementaton, just supporting the off/on states.

Quoted 3 lines

Maybe also mention the relevant documentation: the "ARM CoreLink PCK‑600 Power Control Kit" TRM and the "Arm Power Policy Unit" architecture specification (DEN0051E).

Will do.

Quoted 45 lines
Quoted 13 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +13 -0
+ *
+ * Copyright (c) 2025 Chen-Yu Tsai <[email protected]>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/container_of.h>
+#include <linux/device.h>
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>

drivers/pmdomain/sunxi/sun55i-pck600.c line 26

Quoted 10 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +10 -0
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/string_choices.h>
+
+#define PPU_PWPR    0x0
+#define PPU_PWSR    0x8
+#define      PPU_DCDR0   0x170

white space issue?

drivers/pmdomain/sunxi/sun55i-pck600.c line 29

Quoted 3 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +3 -0
+#define PPU_DCDR1   0x174
+
+#define PPU_PWSR_PWR_STATUS  GENMASK(3, 0)

Would just PPU_PWR_STATUS be a better name, since it's used by both the PWPR and PWSR registers?

Quoted 12 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +12 -0
+#define PPU_POWER_MODE_ON    0x8
+#define PPU_POWER_MODE_OFF   0x0
+
+#define PPU_REG_SIZE 0x1000
+
+struct sunxi_pck600_desc {
+     const char * const *pd_names;
+     unsigned int num_domains;
+     u32 logic_power_switch0_delay_offset;
+     u32 logic_power_switch1_delay_offset;
+     u32 off2on_delay_offset;
+     u32 device_ctrl0_delay;
Quoted 8 lines

drivers/pmdomain/sunxi/sun55i-pck600.c line 45

Quoted 4 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +4 -0
+     u32 device_ctrl1_delay;
+     u32 logic_power_switch0_delay;
+     u32 logic_power_switch1_delay;
+     u32 off2on_delay;

Is there any indication that those parameters are different between different SoCs? I appreciate the idea of making this future-proof, but this might be a bit premature, if all SoCs use the same values?

Quoted 3 lines

It's hard to tell since the BSP driver only covers the A523. I'd just keep this the way it is, since it makes it easier to generalize this to cover PCK-600 in other platforms, if such a need ever presents itself.

Yeah, fair enough, I was just curious. It's fine either way, we can adjust this internal detail later, if need be.

Quoted 31 lines
Quoted 22 lines
Quoted 22 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +22 -0
+};
+
+struct sunxi_pck600_pd {
+     struct generic_pm_domain genpd;
+     struct sunxi_pck600 *pck;
+     void __iomem *base;
+};
+
+struct sunxi_pck600 {
+     struct device *dev;
+     struct genpd_onecell_data genpd_data;
+     struct sunxi_pck600_pd pds[];
+};
+
+#define to_sunxi_pd(gpd) container_of(gpd, struct sunxi_pck600_pd, genpd)
+
+static int sunxi_pck600_pd_set_power(struct sunxi_pck600_pd *pd, bool on)
+{
+     struct sunxi_pck600 *pck = pd->pck;
+     struct generic_pm_domain *genpd = &pd->genpd;
+     int ret;
+     u32 val, reg;
Quoted 8 lines

drivers/pmdomain/sunxi/sun55i-pck600.c line 73

Quoted 6 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +6 -0
+
+     val = on ? PPU_POWER_MODE_ON : PPU_POWER_MODE_OFF;
+
+     reg = readl(pd->base + PPU_PWPR);
+     FIELD_MODIFY(PPU_PWSR_PWR_STATUS, &reg, val);
+     writel(reg, pd->base + PPU_PWPR);

Don't we need a lock here, or is this covered by the power domain framework?

Quoted 2 lines

AFAICT genpd has a lock for each power domain. Since each power domain has its own set of registers, I think we're good here.

Right, I was adittedly lazy yesterday, but now looked it up: indeed there is a lock around every call to genpd_power_{off,on}, so it's all good.

Cheers,
Andre

Quoted 163 lines

Thanks
ChenYu

Quoted 157 lines

Cheers,
Andre

Quoted 152 lines
drivers/pmdomain/sunxi/sun55i-pck600.c new file +152 -0
+
+     /* push write out to hardware */
+     reg = readl(pd->base + PPU_PWPR);
+
+     ret = readl_poll_timeout_atomic(pd->base + PPU_PWSR, reg,
+                                     FIELD_GET(PPU_PWSR_PWR_STATUS, reg) == val,
+                                     0, 10000);
+     if (ret)
+             dev_err(pck->dev, "failed to turn domain \"%s\" %s: %d\n",
+                     genpd->name, str_on_off(on), ret);
+
+     return ret;
+}
+
+static int sunxi_pck600_power_on(struct generic_pm_domain *domain)
+{
+     struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+     return sunxi_pck600_pd_set_power(pd, true);
+}
+
+static int sunxi_pck600_power_off(struct generic_pm_domain *domain)
+{
+     struct sunxi_pck600_pd *pd = to_sunxi_pd(domain);
+
+     return sunxi_pck600_pd_set_power(pd, false);
+}
+
+static void sunxi_pck600_pd_setup(struct sunxi_pck600_pd *pd,
+                               const struct sunxi_pck600_desc *desc)
+{
+     writel(desc->device_ctrl0_delay, pd->base + PPU_DCDR0);
+     writel(desc->device_ctrl1_delay, pd->base + PPU_DCDR1);
+     writel(desc->logic_power_switch0_delay,
+            pd->base + desc->logic_power_switch0_delay_offset);
+     writel(desc->logic_power_switch1_delay,
+            pd->base + desc->logic_power_switch1_delay_offset);
+     writel(desc->off2on_delay, pd->base + desc->off2on_delay_offset);
+}
+
+static int sunxi_pck600_probe(struct platform_device *pdev)
+{
+     struct device *dev = &pdev->dev;
+     const struct sunxi_pck600_desc *desc;
+     struct genpd_onecell_data *genpds;
+     struct sunxi_pck600 *pck;
+     struct reset_control *rst;
+     struct clk *clk;
+     void __iomem *base;
+     int i, ret;
+
+     desc = of_device_get_match_data(dev);
+
+     pck = devm_kzalloc(dev, struct_size(pck, pds, desc->num_domains), GFP_KERNEL);
+     if (!pck)
+             return -ENOMEM;
+
+     pck->dev = &pdev->dev;
+     platform_set_drvdata(pdev, pck);
+
+     genpds = &pck->genpd_data;
+     genpds->num_domains = desc->num_domains;
+     genpds->domains = devm_kcalloc(dev, desc->num_domains,
+                                    sizeof(*genpds->domains), GFP_KERNEL);
+     if (!genpds->domains)
+             return -ENOMEM;
+
+     base = devm_platform_ioremap_resource(pdev, 0);
+     if (IS_ERR(base))
+             return PTR_ERR(base);
+
+     rst = devm_reset_control_get_exclusive_released(dev, NULL);
+     if (IS_ERR(rst))
+             return dev_err_probe(dev, PTR_ERR(rst), "failed to get reset control\n");
+
+     clk = devm_clk_get_enabled(dev, NULL);
+     if (IS_ERR(clk))
+             return dev_err_probe(dev, PTR_ERR(clk), "failed to get clock\n");
+
+     for (i = 0; i < desc->num_domains; i++) {
+             struct sunxi_pck600_pd *pd = &pck->pds[i];
+
+             pd->genpd.name = desc->pd_names[i];
+             pd->genpd.power_off = sunxi_pck600_power_off;
+             pd->genpd.power_on = sunxi_pck600_power_on;
+             pd->base = base + PPU_REG_SIZE * i;
+
+             sunxi_pck600_pd_setup(pd, desc);
+             ret = pm_genpd_init(&pd->genpd, NULL, false);
+             if (ret) {
+                     dev_err_probe(dev, ret, "failed to initialize power domain\n");
+                     goto err_remove_pds;
+             }
+
+             genpds->domains[i] = &pd->genpd;
+     }
+
+     ret = of_genpd_add_provider_onecell(dev_of_node(dev), genpds);
+     if (ret) {
+             dev_err_probe(dev, ret, "failed to add PD provider\n");
+             goto err_remove_pds;
+     }
+
+     return 0;
+
+err_remove_pds:
+     for (i--; i >= 0; i--)
+             pm_genpd_remove(genpds->domains[i]);
+
+     return ret;
+}
+
+static const char * const sun55i_a523_pck600_pd_names[] = {
+     "VE", "GPU", "VI", "VO0", "VO1", "DE", "NAND", "PCIE"
+};
+
+static const struct sunxi_pck600_desc sun55i_a523_pck600_desc = {
+     .pd_names = sun55i_a523_pck600_pd_names,
+     .num_domains = ARRAY_SIZE(sun55i_a523_pck600_pd_names),
+     .logic_power_switch0_delay_offset = 0xc00,
+     .logic_power_switch1_delay_offset = 0xc04,
+     .off2on_delay_offset = 0xc10,
+     .device_ctrl0_delay = 0xffffff,
+     .device_ctrl1_delay = 0xffff,
+     .logic_power_switch0_delay = 0x8080808,
+     .logic_power_switch1_delay = 0x808,
+     .off2on_delay = 0x8
+};
+
+static const struct of_device_id sunxi_pck600_of_match[] = {
+     {
+             .compatible     = "allwinner,sun55i-a523-pck-600",
+             .data           = &sun55i_a523_pck600_desc,
+     },
+     {}
+};
+MODULE_DEVICE_TABLE(of, sunxi_pck600_of_match);
+
+static struct platform_driver sunxi_pck600_driver = {
+     .probe = sunxi_pck600_probe,
+     .driver = {
+             .name   = "sunxi-pck-600",
+             .of_match_table = sunxi_pck600_of_match,
+             /* Power domains cannot be removed if in use. */
+             .suppress_bind_attrs = true,
+     },
+};
+module_platform_driver(sunxi_pck600_driver);
+
+MODULE_DESCRIPTION("Allwinner PCK-600 power domain driver");
+MODULE_AUTHOR("Chen-Yu Tsai <[email protected]>");
+MODULE_LICENSE("GPL");