Skip to contentSkip to conversation

sunxi: Enable SPL/SPI boot for OLinuXino Lime2

PATCH In review Eric Anderson 2 participants 3 messages Jul 13, 2025 – Aug 12, 2025 Arm/Allwinner sunXi SoC support

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 sunxi: Enable SPL/SPI boot for OLinuXino Lime2

58e9502e6 "arm: sunxi: Enable SPL/SPI boot for Olinuxino Lime2-eMMC boards" enabled SPI boot for the eMMC variant. Olimex offers the "s16MB" variant with SPI flash populated but without eMMC populated. Tested on board rev L.

---
 configs/A20-OLinuXino-Lime2_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/A20-OLinuXino-Lime2_defconfig +1 -0
index f885fc01e6e..a2c3dade795 100644
@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime2"
 CONFIG_SPL=y
+CONFIG_SPL_SPI_SUNXI=y
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
 CONFIG_I2C1_ENABLE=y
Signature · 1 line
2.50.0
Reviewed-by on v1 1/1
#1 lore raw

On Sat, 12 Jul 2025 17:27:41 -0700
Eric Anderson <[email protected]> wrote:

Hi,

Quoted 4 lines

58e9502e6 "arm: sunxi: Enable SPL/SPI boot for Olinuxino Lime2-eMMC boards" enabled SPI boot for the eMMC variant. Olimex offers the "s16MB" variant with SPI flash populated but without eMMC populated. Tested on board rev L.

Indeed there is a config without eMMC and with SPI flash in their shop.

But actually I wonder why Olimex has two different DTs for the eMMC-less boards and the board with eMMC. Many other boards make eMMC optional, either as separate SKUs, or when eMMC is on a module. And we just go with one DT, describing the eMMC, the code will just skip the initialisation if no "card" is found. That affects the A20 and A64 boards.

So I wonder if anyone wants to clean this up, because I think we would only need the A20-OLinuXino-Lime2-eMMC_defconfig, A20-OLinuXino_MICRO-eMMC_defconfig and a64-olinuxino_defconfig.

Quoted 10 lines
---
 configs/A20-OLinuXino-Lime2_defconfig | 1 +
 1 file changed, 1 insertion(+)
configs/A20-OLinuXino-Lime2_defconfig +0 -0
index f885fc01e6e..a2c3dade795 100644

configs/A20-OLinuXino-Lime2_defconfig CONFIG_ARM=y · line 5

Quoted 4 lines
configs/A20-OLinuXino-Lime2_defconfig +1 -0
@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-olinuxino-lime2"
 CONFIG_SPL=y
+CONFIG_SPL_SPI_SUNXI=y

This needs to go further down below. After configuring for a board, run "make savedefconfig", then compare the generated "defconfig" file with your ..._defconfig version (or just copy ./defconfig over).

With this fixed:

Will fix this up while committing, so no further action needed.

Cheers,
Andre

Quoted 3 lines
configs/A20-OLinuXino-Lime2_defconfig +0 -0
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
 CONFIG_I2C1_ENABLE=y
#2 lore raw
Quoted 6 lines · Andre Przywara

But actually I wonder why Olimex has two different DTs for the eMMC-less boards and the board with eMMC.
...snip...
So I wonder if anyone wants to clean this up, because I think we would only need the A20-OLinuXino-Lime2-eMMC_defconfig, A20-OLinuXino_MICRO-eMMC_defconfig and a64-olinuxino_defconfig.

I had wondered the same, but expected I'd not understand. Looking just now, it sounds like it doesn't mix with the NAND variant (-n8G) well?

https://github.com/torvalds/linux/commit/27dd9af6bc000ab21fdd41e58e3dddedba57ab92

It looks like the emmc DT has gotten slightly slimmer since being introduced. It doesn't seem the eMMC DT turns off any part of the NAND DT, so I might try to poke at this some. But I don't have a NAND version of the board to fully test.

Quoted 6 lines
Quoted 2 lines

CONFIG_SPL=y
+CONFIG_SPL_SPI_SUNXI=y

This needs to go further down below. After configuring for a board, run "make savedefconfig", then compare the generated "defconfig" file with your ..._defconfig version (or just copy ./defconfig over).

Oh, right, the tooling would know the proper order. I just sorted it, but I forgot I had wondered earlier how things were ordered. Thanks for the explanation.

Thanks for fixing it up.