Skip to contentSkip to conversation

riscv: dts: starfive: jh7110-common: add status power led node

PATCH In review E Shattow 2 participants 3 messages Jul 16, 2025

Subsystems (3)
Device tree bindings RISC-V StarFive devicetrees
lore
Share & tools
lore

E Shattow

author
#0 lore raw

PATCH 1/1 riscv: dts: starfive: jh7110-common: add status power led node

Add status power led node for StarFive VisionFive2 and variant boards.

Signed-off-by E Shattow <[email protected]>
---
 arch/riscv/boot/dts/starfive/jh7110-common.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/riscv/boot/dts/starfive/jh7110-common.dtsi +9 -0
index 4baeb981d4df..2eaf01775ef5 100644
@@ -8,6 +8,7 @@
 #include "jh7110.dtsi"
 #include "jh7110-pinfunc.h"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/starfive,jh7110-pinctrl.h>
 
 / {

@@ -38,6 +39,14 @@ gpio-restart {
 		priority = <224>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_power: led-0 {
+			gpios = <&aongpio 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	pwmdac_codec: audio-codec {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;

base-commit: 155a3c003e555a7300d156a5252c004c392ec6b0

Signature · 1 line
2.50.0
maintainer
#1 lore raw
Quoted 3 lines · E Shattow

Add status power led node for StarFive VisionFive2 and variant boards.

Signed-off-by E Shattow <[email protected]>

Again, I'll grab this too but it may be too late for 6.17.

Quoted 36 lines
---
 arch/riscv/boot/dts/starfive/jh7110-common.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/riscv/boot/dts/starfive/jh7110-common.dtsi +9 -0
index 4baeb981d4df..2eaf01775ef5 100644
@@ -8,6 +8,7 @@
 #include "jh7110.dtsi"
 #include "jh7110-pinfunc.h"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/starfive,jh7110-pinctrl.h>
 
 / {

@@ -38,6 +39,14 @@ gpio-restart {
 		priority = <224>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_power: led-0 {
+			gpios = <&aongpio 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	pwmdac_codec: audio-codec {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;

base-commit: 155a3c003e555a7300d156a5252c004c392ec6b0

Signature · 1 line
2.50.0
author
#2 lore raw
Quoted 39 lines · Conor Dooley
Quoted 3 lines · E Shattow

Add status power led node for StarFive VisionFive2 and variant boards.

Signed-off-by E Shattow <[email protected]>

Again, I'll grab this too but it may be too late for 6.17.

Quoted 32 lines
---
 arch/riscv/boot/dts/starfive/jh7110-common.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/riscv/boot/dts/starfive/jh7110-common.dtsi +9 -0
index 4baeb981d4df..2eaf01775ef5 100644
@@ -8,6 +8,7 @@
 #include "jh7110.dtsi"
 #include "jh7110-pinfunc.h"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/starfive,jh7110-pinctrl.h>
 
 / {

@@ -38,6 +39,14 @@ gpio-restart {
 		priority = <224>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_power: led-0 {
+			gpios = <&aongpio 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	pwmdac_codec: audio-codec {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;
Quoted 4 lines
Quoted 4 lines

base-commit: 155a3c003e555a7300d156a5252c004c392ec6b0

Signature · 1 line
2.50.0

Ok sounds good to me. This is common on all JH7110 boards, but am not sure if it is connected to anything on DeepComputing Framework 13 V01.

LED color varies yet there is an LED connected this way on variants I could find a published schematic for:
- Milk-V Mars
- Pine64 Star64
- StarFive VisionFive2 1.2a
- StarFive VisionFive2 1.3b

Discussion about the OrangePi RV dts shows this to have the same connection to an LED. I am putting together patches for adding Milk-V Mars CM and Milk-V Mars CM Lite, tested successfully and listed on schematics as well. Some early revision developer sample board schematics for some of the above do not list RGPIO3 so assumed n/c and no problem there.

If anyone out there can link to the FML13V01 schematic or confirm this change does not break for users I'd appreciate that, for any follow-up that might be needed per-board.

-E