dt-bindings: clock: Convert silabs,si5341 to DT schema

deleted file mode 100644
index ce55aba0ce22..000000000000
@@ -1,175 +0,0 @@
-Binding for Silicon Labs Si5340, Si5341 Si5342, Si5344 and Si5345 programmable
-i2c clock generator.
-
-Reference
-[1] Si5341 Data Sheet
-    https://www.silabs.com/documents/public/data-sheets/Si5341-40-D-DataSheet.pdf
-[2] Si5341 Reference Manual
-    https://www.silabs.com/documents/public/reference-manuals/Si5341-40-D-RM.pdf
-[3] Si5345 Reference Manual
-    https://www.silabs.com/documents/public/reference-manuals/Si5345-44-42-D-RM.pdf
-
-The Si5341 and Si5340 are programmable i2c clock generators with up to 10 output
-clocks. The chip contains a PLL that sources 5 (or 4) multisynth clocks, which
-in turn can be directed to any of the 10 (or 4) outputs through a divider.
-The internal structure of the clock generators can be found in [2].
-The Si5345 is similar to the Si5341 with the addition of fractional input
-dividers and automatic input selection, as described in [3].
-The Si5342 and Si5344 are smaller versions of the Si5345, with 2 or 4 outputs.
-
-The driver can be used in "as is" mode, reading the current settings from the
-chip at boot, in case you have a (pre-)programmed device. If the PLL is not
-configured when the driver probes, it assumes the driver must fully initialize
-it.
-
-The device type, speed grade and revision are determined runtime by probing.
-
-The driver currently does not support any fancy input configurations. They can
-still be programmed into the chip and the driver will leave them "as is".
-
-==I2C device node==
-
-Required properties:
-- compatible: shall be one of the following:
-	"silabs,si5340" - Si5340 A/B/C/D
-	"silabs,si5341" - Si5341 A/B/C/D
-	"silabs,si5342" - Si5342 A/B/C/D
-	"silabs,si5344" - Si5344 A/B/C/D
-	"silabs,si5345" - Si5345 A/B/C/D
-- reg: i2c device address, usually 0x74
-- #clock-cells: from common clock binding; shall be set to 2.
-	The first value is "0" for outputs, "1" for synthesizers.
-	The second value is the output or synthesizer index.
-- clocks: from common clock binding; list of parent clock  handles,
-	corresponding to inputs. Use a fixed clock for the "xtal" input.
-	At least one must be present.
-- clock-names: One of: "xtal", "in0", "in1", "in2"
-
-Optional properties:
-- vdd-supply: Regulator node for VDD
-- vdda-supply: Regulator node for VDDA
-- vdds-supply: Regulator node for VDDS
-- silabs,pll-m-num, silabs,pll-m-den: Numerator and denominator for PLL
-  feedback divider. Must be such that the PLL output is in the valid range. For
-  example, to create 14GHz from a 48MHz xtal, use m-num=14000 and m-den=48. Only
-  the fraction matters, using 3500 and 12 will deliver the exact same result.
-  If these are not specified, and the PLL is not yet programmed when the driver
-  probes, the PLL will be set to 14GHz.
-- silabs,reprogram: When present, the driver will always assume the device must
-  be initialized, and always performs the soft-reset routine. Since this will
-  temporarily stop all output clocks, don't do this if the chip is generating
-  the CPU clock for example.
-- silabs,xaxb-ext-clk: When present, indicates that the XA/XB pins are used
-  in EXTCLK (external reference clock) rather than XTAL (crystal) mode.
-- interrupts: Interrupt for INTRb pin.
-- silabs,iovdd-33: When present, indicates that the I2C lines are using 3.3V
-  rather than 1.8V thresholds.
-- vddoX-supply (where X is an output index): Regulator node for VDDO for the
-  specified output. The driver selects the output VDD_SEL setting based on this
-  voltage.
-- #address-cells: shall be set to 1.
-- #size-cells: shall be set to 0.
-
-
-== Child nodes: Outputs ==
-
-The child nodes list the output clocks.
-
-Each of the clock outputs can be overwritten individually by using a child node.
-If a child node for a clock output is not set, the configuration remains
-unchanged.
-
-Required child node properties:
-- reg: number of clock output.
-
-Optional child node properties:
-- silabs,format: Output format, one of:
-	1 = differential (defaults to LVDS levels)
-	2 = low-power (defaults to HCSL levels)
-	4 = LVCMOS
-- silabs,common-mode: Manually override output common mode, see [2] for values
-- silabs,amplitude: Manually override output amplitude, see [2] for values
-- silabs,synth-master: boolean. If present, this output is allowed to change the
-	multisynth frequency dynamically.
-- silabs,silabs,disable-high: boolean. If set, the clock output is driven HIGH
-	when disabled, otherwise it's driven LOW.
-
-==Example==
-
-/* 48MHz reference crystal */
-ref48: ref48M {
-	compatible = "fixed-clock";
-	#clock-cells = <0>;
-	clock-frequency = <48000000>;
-};
-
-i2c-master-node {
-	/* Programmable clock (for logic) */
-	si5341: clock-generator@74 {
-		reg = <0x74>;
-		compatible = "silabs,si5341";
-		#clock-cells = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&ref48>;
-		clock-names = "xtal";
-
-		silabs,pll-m-num = <14000>; /* PLL at 14.0 GHz */
-		silabs,pll-m-den = <48>;
-		silabs,reprogram; /* Chips are not programmed, always reset */
-
-		out@0 {
-			reg = <0>;
-			silabs,format = <1>; /* LVDS 3v3 */
-			silabs,common-mode = <3>;
-			silabs,amplitude = <3>;
-			silabs,synth-master;
-		};
-
-		/*
-		 * Output 6 configuration:
-		 *  LVDS 1v8
-		 */
-		out@6 {
-			reg = <6>;
-			silabs,format = <1>; /* LVDS 1v8 */
-			silabs,common-mode = <13>;
-			silabs,amplitude = <3>;
-		};
-
-		/*
-		 * Output 8 configuration:
-		 *  HCSL 3v3
-		 */
-		out@8 {
-			reg = <8>;
-			silabs,format = <2>;
-			silabs,common-mode = <11>;
-			silabs,amplitude = <3>;
-		};
-	};
-};
-
-some-video-node {
-	/* Standard clock bindings */
-	clock-names = "pixel";
-	clocks = <&si5341 0 7>; /* Output 7 */
-
-	/* Set output 7 to use syntesizer 3 as its parent */
-	assigned-clocks = <&si5341 0 7>, <&si5341 1 3>;
-	assigned-clock-parents = <&si5341 1 3>;
-	/* Set output 7 to 148.5 MHz using a synth frequency of 594 MHz */
-	assigned-clock-rates = <148500000>, <594000000>;
-};
-
-some-audio-node {
-	clock-names = "i2s-clk";
-	clocks = <&si5341 0 0>;
-	/*
-	 * since output 0 is a synth-master, the synth will be automatically set
-	 * to an appropriate frequency when the audio driver requests another
-	 * frequency. We give control over synth 2 to this output here.
-	 */
-	assigned-clocks = <&si5341 0 0>;
-	assigned-clock-parents = <&si5341 1 2>;
-};

217 lines not on this page · raw message