Skip to contentSkip to conversation

kho: only fill kimage if KHO is finalized

PATCH Applied Pratyush Yadav 2 participants 2 messages Sep 18, 2025 – Sep 19, 2025

Subsystems (4)
lore
Share & tools
lore

Pratyush Yadav

author maintainer
#0 lore raw

PATCH 1/1 kho: only fill kimage if KHO is finalized

kho_fill_kimage() only checks for KHO being enabled before filling in the FDT to the image. KHO being enabled does not mean that the kernel has data to hand over. That happens when KHO is finalized.

When a kexec is done with KHO enabled but not finalized, the FDT page is allocated but not initialized. FDT initialization happens after finalize. This means the KHO segment is filled in but the FDT contains garbage data.

This leads to the below error messages in the next kernel:

    [    0.000000] KHO: setup: handover FDT (0x10116b000) is invalid: -9
    [    0.000000] KHO: disabling KHO revival: -22

There is no problem in practice, and the next kernel boots and works fine. But this still leads to misleading error messages and garbage being handed over.

Only fill in KHO segment when KHO is finalized. When KHO is not enabled, the debugfs interface is not created and there is no way to finalize it anyway. So the check for kho_enable is not needed, and kho_out.finalize alone is enough.

Fixes 3bdecc3c93f9f ("kexec: add KHO support to kexec file loads")
---
 kernel/kexec_handover.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/kexec_handover.c +1 -1
index 8079fc4b9189..5ff959a90165 100644
@@ -1242,7 +1242,7 @@ int kho_fill_kimage(struct kimage *image)
 	int err = 0;
 	struct kexec_buf scratch;
 
-	if (!kho_enable)
+	if (!kho_out.finalized)
 		return 0;
 
 	image->kho.fdt = page_to_phys(kho_out.ser.fdt);
Signature · 1 line
2.47.3
maintainer Reviewed-by on v1 1/1
#1 lore raw
Quoted 18 lines · Pratyush Yadav

kho_fill_kimage() only checks for KHO being enabled before filling in the FDT to the image. KHO being enabled does not mean that the kernel has data to hand over. That happens when KHO is finalized.

When a kexec is done with KHO enabled but not finalized, the FDT page is allocated but not initialized. FDT initialization happens after finalize. This means the KHO segment is filled in but the FDT contains garbage data.

This leads to the below error messages in the next kernel:

    [    0.000000] KHO: setup: handover FDT (0x10116b000) is invalid: -9
    [    0.000000] KHO: disabling KHO revival: -22

There is no problem in practice, and the next kernel boots and works fine. But this still leads to misleading error messages and garbage being handed over.

Quoted 7 lines

Only fill in KHO segment when KHO is finalized. When KHO is not enabled, the debugfs interface is not created and there is no way to finalize it anyway. So the check for kho_enable is not needed, and kho_out.finalize alone is enough.

Fixes 3bdecc3c93f9f ("kexec: add KHO support to kexec file loads")

Nice catch!

Quoted 20 lines
---
 kernel/kexec_handover.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/kexec_handover.c +1 -1
index 8079fc4b9189..5ff959a90165 100644
@@ -1242,7 +1242,7 @@ int kho_fill_kimage(struct kimage *image)
 	int err = 0;
 	struct kexec_buf scratch;
 
-	if (!kho_enable)
+	if (!kho_out.finalized)
 		return 0;
 
 	image->kho.fdt = page_to_phys(kho_out.ser.fdt);
Signature · 1 line
2.47.3
Signature · 2 lines
Sincerely yours,
Mike.