Add two new ID for MediaTek's Bluetooth
Subsystems (2)
v2 cover Add two new ID for MediaTek's Bluetooth
In response to the customer's request, add the following two VID/PID to the USB driver table so that btusb driver can support the corresponding MT7920/MT7922 modules.
1. VID/PID 0489/e135 for MT7920
2. VID/PID 0489/e170 for MT7922
---v1->v2: Change patch title
---
Chris Lu (2):
Bluetooth: btusb: MT7920: Add VID/PID 0489/e135
Bluetooth: btusb: MT7922: Add VID/PID 0489/e170
drivers/bluetooth/btusb.c | 4 ++++ 1 file changed, 4 insertions(+)
Signature · 1 line
2.45.2
PATCH RESEND v2 1/2 Bluetooth: btusb: MT7920: Add VID/PID 0489/e135
Add VID 0489 & PID e135 for MediaTek MT7920 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e135 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
--- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/bluetooth/btusb.c +2 -0
@@ -621,6 +621,8 @@ static const struct usb_device_id quirks_table[] = {/* Additional MediaTek MT7920 Bluetooth devices */ { USB_DEVICE(0x0489, 0xe134), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0489, 0xe135), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x13d3, 0x3620), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x13d3, 0x3621), .driver_info = BTUSB_MEDIATEK |
Signature · 1 line
2.45.2
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1011622
---Test result---
Test Summary:
CheckPatch PENDING 0.47 seconds GitLint PENDING 0.34 seconds SubjectPrefix PASS 0.12 seconds BuildKernel PASS 24.61 seconds CheckAllWarning PASS 27.10 seconds CheckSparse PASS 30.67 seconds BuildKernel32 PASS 24.58 seconds TestRunnerSetup PASS 493.08 seconds TestRunner_l2cap-tester PASS 24.07 seconds TestRunner_iso-tester FAIL 40.44 seconds TestRunner_bnep-tester PASS 6.14 seconds TestRunner_mgmt-tester FAIL 113.57 seconds TestRunner_rfcomm-tester PASS 9.33 seconds TestRunner_sco-tester PASS 14.48 seconds TestRunner_ioctl-tester FAIL 10.35 seconds TestRunner_mesh-tester FAIL 11.35 seconds TestRunner_smp-tester PASS 8.47 seconds TestRunner_userchan-tester PASS 6.49 seconds IncrementalBuild PENDING 0.67 seconds
Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script Output:
##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:
##############################
Test: TestRunner_iso-tester - FAIL
Desc: Run iso-tester with test-runner
Output:
No test result found
##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner Output:
Total: 490, Passed: 482 (98.4%), Failed: 4, Not Run: 4
Failed Test Cases
Pair Device - Legacy Success 1 Failed 0.195 seconds Pair Device - Sec Mode 3 Success 1 Failed 0.176 seconds Pair Device - Legacy Reject 2 Failed 0.152 seconds Read Exp Feature - Success Failed 0.112 seconds
##############################
Test: TestRunner_ioctl-tester - FAIL
Desc: Run ioctl-tester with test-runner Output:
Total: 28, Passed: 26 (92.9%), Failed: 2, Not Run: 0
Failed Test Cases
Connection List Failed 1.055 seconds Connection Info Failed 0.139 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0
Failed Test Cases
Mesh - Send cancel - 1 Timed out 1.800 seconds Mesh - Send cancel - 2 Timed out 1.994 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series Output:
---
Regards,
Linux Bluetooth
Re: [PATCH v2 RESEND 1/2] Bluetooth: btusb: MT7920: Add VID/PID 0489/e135
In reply to Chris LuDear Chris,
Thank you for the patch.
Am 15.10.25 um 05:31 schrieb Chris Lu:
Quoted 55 lines
Add VID 0489 & PID e135 for MediaTek MT7920 USB Bluetooth chip.
The information in
/sys/kernel/debug/usb/devicesabout the Bluetooth device is listed as the below.T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e135 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125usSigned-off-by Chris Lu <[email protected]>--- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+)drivers/bluetooth/btusb.c +0
-0
drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 628
Quoted 8 lines
drivers/bluetooth/btusb.c +2
-0@@ -621,6 +621,8 @@ static const struct usb_device_id quirks_table[] = {/* Additional MediaTek MT7920 Bluetooth devices */ { USB_DEVICE(0x0489, 0xe134), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0489, 0xe135), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x13d3, 0x3620), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x13d3, 0x3621), .driver_info = BTUSB_MEDIATEK |
Kind regards,
Paul
PATCH RESEND v2 2/2 Bluetooth: btusb: MT7922: Add VID/PID 0489/e170
In reply to Chris LuAdd VID 0489 & PID e170 for MediaTek MT7922 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below.
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e170 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
--- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/bluetooth/btusb.c +2 -0
@@ -687,6 +687,8 @@ static const struct usb_device_id quirks_table[] = { BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0489, 0xe153), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0489, 0xe170), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x04ca, 0x3804), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x04ca, 0x38e4), .driver_info = BTUSB_MEDIATEK |
Signature · 1 line
2.45.2
Re: [PATCH v2 RESEND 2/2] Bluetooth: btusb: MT7922: Add VID/PID 0489/e170
Dear Chris,
Thank you for your patch.
Am 15.10.25 um 05:31 schrieb Chris Lu:
Quoted 55 lines
Add VID 0489 & PID e170 for MediaTek MT7922 USB Bluetooth chip.
The information in
/sys/kernel/debug/usb/devicesabout the Bluetooth device is listed as the below.T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e170 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125usSigned-off-by Chris Lu <[email protected]>--- drivers/bluetooth/btusb.c | 2 ++ 1 file changed, 2 insertions(+)drivers/bluetooth/btusb.c +0
-0
drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 694
Quoted 8 lines
drivers/bluetooth/btusb.c +2
-0@@ -687,6 +687,8 @@ static const struct usb_device_id quirks_table[] = { BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x0489, 0xe153), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, + { USB_DEVICE(0x0489, 0xe170), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x04ca, 0x3804), .driver_info = BTUSB_MEDIATEK | BTUSB_WIDEBAND_SPEECH }, { USB_DEVICE(0x04ca, 0x38e4), .driver_info = BTUSB_MEDIATEK |
Kind regards,
Paul
This series was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:
Hello:
This series was applied to bluetooth/bluetooth-next.git (master) by Luiz Augusto von Dentz <[email protected]>:
Quoted 8 lines · On Wed, 15 Oct 2025 11:31:48 +0800 you wrote:
In response to the customer's request, add the following two VID/PID to the USB driver table so that btusb driver can support the corresponding MT7920/MT7922 modules.
1. VID/PID 0489/e135 for MT7920
2. VID/PID 0489/e170 for MT7922[...]
Here is the summary with links:
- [v2,RESEND,1/2] Bluetooth: btusb: MT7920: Add VID/PID 0489/e135
https://git.kernel.org/bluetooth/bluetooth-next/c/bb9da27b29d0 - [v2,RESEND,2/2] Bluetooth: btusb: MT7922: Add VID/PID 0489/e170 https://git.kernel.org/bluetooth/bluetooth-next/c/042b9b4c55c7
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html